Jeremy Vial [Thu, 31 Jul 2014 13:10:33 +0000 (15:10 +0200)]
ARM: OMAP3: Fix choice of omap3_restore_es function in OMAP34XX rev3.1.2 case.
According to the comment “restore_es3: applies to 34xx >= ES3.0" in
"arch/arm/mach-omap2/sleep34xx.S”, omap3_restore_es3 should be used
if the revision of an OMAP34xx is ES3.1.2.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Tue, 29 Jul 2014 11:03:30 +0000 (04:03 -0700)]
Merge tag 'for-v3.17/omap-clock-b' of git://git./linux/kernel/git/pjw/omap-pending into omap-for-v3.17/soc
Modify OMAP PLL rate rounding function to round to the exact rate requested
or the next one below it. This is intended to resolve some DSS problems.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/clock-b-v3.17/
20140725061121/
Paul Walmsley [Fri, 25 Jul 2014 12:11:15 +0000 (06:11 -0600)]
ARM: OMAP2+: clock: allow omap2_dpll_round_rate() to round to next-lowest rate
Change the behavior of omap2_dpll_round_rate() to round to either the
exact rate requested, or the next lowest rate that the clock is able to
provide.
This is not an ideal fix, but is intended to provide a relatively safe
way for drivers to set PLL rates, until a better solution can be
implemented.
For the time being, omap3_noncore_dpll_set_rate() is still allowed to
set its rate to something other than what the caller requested; but will
warn when this occurs.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tony Lindgren [Wed, 23 Jul 2014 08:26:02 +0000 (01:26 -0700)]
Merge branch 'omap-for-v3.17/mailbox' into omap-for-v3.17/soc
Tony Lindgren [Wed, 23 Jul 2014 08:21:33 +0000 (01:21 -0700)]
Merge tag 'for-v3.17/omap-hwmod-a' of git://git./linux/kernel/git/pjw/omap-pending into omap-for-v3.17/soc
OMAP hwmod data additions for v3.17. Most of these are DRA7xx-related,
although one patch adds DSS hwmods for AM43xx.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-v3.17/
20140722143514/
Lokesh Vutla [Tue, 22 Jul 2014 19:15:57 +0000 (13:15 -0600)]
ARM: DRA7: hwmod: Add data for RTC
Add hwmod data for RTC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Mugunthan V N [Tue, 8 Jul 2014 13:16:39 +0000 (18:46 +0530)]
arm: dra7xx: Add hwmod data for MDIO and CPSW
Adding hwmod data for CPSW and MDIO which is present in DRA7xx SoC
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kishon Vijay Abraham I [Wed, 9 Jul 2014 09:02:47 +0000 (14:32 +0530)]
arm: dra7xx: Add hwmod data for pcie1 and pcie2 subsystems
Added hwmod data for pcie1 and pcie2 subsystem present in DRA7xx SOC.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Kishon Vijay Abraham I [Wed, 25 Jun 2014 18:02:45 +0000 (23:32 +0530)]
arm: dra7xx: Add hwmod data for pcie1 phy and pcie2 phy
Added hwmod data for pcie1 and pcie2 phy present in DRA7xx SOC.
Also added the missing CLKCTRL OFFSET macro and CONTEXT OFFSET macro
for pcie1 phy and pcie2 phy.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Roger Quadros [Sat, 5 Jul 2014 23:44:58 +0000 (17:44 -0600)]
ARM: DRA7: hwmod: Add OCP2SCP3 module
This module is needed for the SATA and PCIe PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Nishanth Menon [Thu, 12 Jun 2014 11:45:23 +0000 (17:15 +0530)]
ARM: DRA7: hwmod: remove interrupts for DMA
DMA interrupts are now available in of, and the definitions are
duplicates in hwmod. This prevents us from dynamically allocating
interrupt resources for dma from devicetree.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Nishanth Menon [Thu, 12 Jun 2014 11:45:22 +0000 (17:15 +0530)]
ARM: OMAP2+: DMA: remove requirement of irq for platform-dma driver
we have currently 2 DMA drivers that try to co-exist.
drivers/dma/omap-dma.c which registers it's own IRQ and is device tree
aware and uses arch/arm/plat-omap/dma.c instance created by
arch/arm/mach-omap2/dma.c to maintain channel usage (omap_request_dma).
Currently both try to register interrupts and mach-omap2/plat-omap dma.c
attempts to use the IRQ number registered by hwmod to register it's own
interrupt handler.
Now, there is no reasonable way of static allocating DMA irq in GIC
SPI when we use crossbar. However, since the dma_chan structure is
freed as a result of IRQ not being present due to devm allocation,
maintaining information of channel by platform code fails at a later
point in time when that region of memory is reused.
So, if hwmod does not indicate an IRQ number, then, assume that
dma-engine will take care of the interrupt handling.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 21 Jul 2014 07:35:38 +0000 (00:35 -0700)]
Merge tag 'for-v3.17/omap-clock-a' of git://git./linux/kernel/git/pjw/omap-pending into omap-for-v3.17/soc
An OMAP clock cleanup series for 3.17 from Tero Kristo.
This is in preparation for moving this code into drivers/clk/ti.
Basic build, boot, and PM test logs are here:
http://www.pwsan.com/omap/testlogs/clock-a-v3.17/
20140717034329/
Tero Kristo [Wed, 2 Jul 2014 08:47:47 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/interface: remove some headers from clkt_iclk.c file
Instead, copy the used constants from the header file to the source file.
This allows the code to be migrated under drivers folder where we don't
have access to the OMAP specific header files.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:46 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/dpll: remove unused header includes from dpll3xxx.c
Some of the machine specific header includes are no longer used, so remove
these from the source file. This allows migration of the file under clock
driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:45 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/dpll: remove unused header includes from clkt_dpll.c
Some of the machine specific header includes are no longer used, so remove
these from the source file. This allows migration of the file under clock
driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:44 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/interface: add a clk_features definition for idlest value
Helps to get rid of some runtime cpu_is_x checks. This also allows eventual
migration of the code under clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:43 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/dpll: add jitter correction behind clk_features
Currently DPLL code uses runtime cpu_is_343x checks to see if the DPLL
has freqsel fields in its control register or not. Instead, add a new
flag to the clk_features.flags and use this during runtime. Allows
eventual move of the DPLL code under clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:42 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/dpll: convert bypass check to use clk_features
OMAP2 DPLL code for checking whether DPLL is in bypass mode now uses
clk_features data provided during boot. This avoids the need to use
cpu_is_X type checks runtime, and allows us to eventually move the
clock code under the clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:41 +0000 (11:47 +0300)]
ARM: OMAP2+: clock/dpll: add private API for checking if DPLL is in bypass
Currently, same functionality is copy pasted in two locations. Instead,
add a private API for this and get rid of some duplicated code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:40 +0000 (11:47 +0300)]
ARM: OMAP2+: clock: add fint values to the ti_clk_features struct
These are SoC specific and get their init values based on the SoC type.
Previously the values were hard coded within the DPLL clock code, but
having them inside the clock features avoids runtime cpu_is_X type checks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:39 +0000 (11:47 +0300)]
ARM: OMAP2+: clock: introduce ti_clk_features flags
This shall be used to replace the cpu type checks around the clock code.
Actual bit values will be introduced in patches later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:38 +0000 (11:47 +0300)]
ARM: OMAP4+: dpll44xx: remove cm-regbits-44xx.h and clock44xx.h includes
Instead, copy the used bitfield definitions to the source file. Done in
preparation to migrate the clock implementation under clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:37 +0000 (11:47 +0300)]
ARM: OMAP4+: dpll: remove cpu_is_omap44xx checks
These are unnecessary, as the clock code is only used on OMAP4+ platforms
through clock registrations. This also allows to eventually migrate the
clock type implementation under clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tony Lindgren [Tue, 15 Jul 2014 14:00:00 +0000 (07:00 -0700)]
Merge branch 'for-v3.17/cm-prm-cleanup' of https://github.com/t-kristo/linux-pm into omap-for-v3.17/soc
Suman Anna [Fri, 11 Jul 2014 21:44:43 +0000 (16:44 -0500)]
ARM: AM33xx: hwmod_data: Remove legacy mailbox addrs
The legacy-style definition of the hwmod addr space is no longer
required as AM33xx/AM43xx are DT-boot only, and the minimal mailbox
DT nodes have been added, so clean up this data.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:42 +0000 (16:44 -0500)]
ARM: OMAP4: hwmod_data: Remove legacy mailbox addrs
The legacy-style definition of the hwmod addr space is no longer
required after the addition of the OMAP4 mailbox DT node, so
clean up this data.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:41 +0000 (16:44 -0500)]
ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs
OMAP2 devices are devicetree boot only, and the legacy mode
of mailbox device creation should no longer be used, so remove
the mailbox attribute data and the hwmod addr space used for
creating mailboxes in legacy mode.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:40 +0000 (16:44 -0500)]
ARM: OMAP2+: Avoid mailbox legacy device creation for DT-boot
The legacy platform device for mailbox should not be created for
a DT boot, so adjust the platform device initialization logic
appropriately.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:39 +0000 (16:44 -0500)]
ARM: DRA7: hwmod_data: Add mailbox hwmod data
Add the hwmod data for the 13 instances of the system mailbox
IP in DRA7 SoC. The patch is needed for performing a soft-reset
while configuring the respective mailbox instance, otherwise is
a non-essential change for functionality. The modules are smart
idled on reset, and the IP module mode is hardware controlled.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:38 +0000 (16:44 -0500)]
ARM: dts: DRA7: Add mailbox nodes
DRA7xx has 13 system mailboxes, and is present on both the
DRA72x and DRA74x family of SoCs. Add the DT nodes for all
these 13 mailboxes. Except for mailbox 1, all other mailboxes
do not have interrupts mapped into the MPU GIC by default.
All the mailboxes have been disabled and the interrupts
property information is left out intentionally for now,
because of the dependencies against the crossbar driver.
These mailboxes can be enabled when a usecase arises
and the crossbar driver dependencies are met.
NOTE: The mailbox 1 has different number of mailbox fifos
and IP interrupts compared to the remaining 12 mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:37 +0000 (16:44 -0500)]
ARM: dts: AM4372: Correct mailbox node data
The mailbox DT node for AM4372 is enabled and is corrected to
remove some properties that have crept in by mistake.
Fixes: 9e3269b (ARM: dts: AM4372: Add L2, EDMA, mailbox, MMC and SHAM nodes)
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:36 +0000 (16:44 -0500)]
ARM: dts: AM33xx: Add mailbox node
The mailbox DT node data has been added for AM33xx device.
The mailbox IP in AM33xx is similar to the version found in
OMAP4+ devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:35 +0000 (16:44 -0500)]
ARM: dts: OMAP4: Add mailbox node
The mailbox DT node data has been added for OMAP44xx
devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suman Anna [Fri, 11 Jul 2014 21:44:34 +0000 (16:44 -0500)]
ARM: dts: OMAP2+: Add mailbox fifo and user information
The number of mailbox fifos and users (IP interrupts) are added
to the Mailbox DT nodes on OMAP2420, OMAP2430, OMAP3, and OMAP5
family of SoCs through the DT properties "ti,mbox-num-fifos" and
"ti,mbox-num-users" properties. This data represents the same data
that used to be represented in hwmod attribute data through the
.num_fifos and .num_users fields previously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tero Kristo [Wed, 2 Jul 2014 08:47:36 +0000 (11:47 +0300)]
ARM: OMAP4+: clock: remove DEFINE_CLK_OMAP_HSDIVIDER macro
This clock type declaration is no longer used as all omap4+ SoC clock
data has been moved to DT, thus remove it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Joachim Eastwood [Wed, 21 May 2014 15:48:48 +0000 (17:48 +0200)]
ARM: OMAP4: Ctrl module register define diet
The mach-omap2 directory contains full register defines for OMAP4
control module but only around 27 of those are used. There are is
a total of 1795 register defines in four files with only 27 in use.
That is pretty low usefulness ratio...
I guess alot more was used when we had omap4 board files and
mach-omap2 contained more drivers but this has now changed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Sun, 6 Jul 2014 19:37:51 +0000 (12:37 -0700)]
Linux 3.16-rc4
Linus Torvalds [Sun, 6 Jul 2014 19:11:57 +0000 (12:11 -0700)]
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bugfix from Grant Likely:
"Important bug fix for parsing 64-bit addresses on 32-bit platforms.
Without this patch the kernel will try to use memory ranges that
cannot be reached"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch
Linus Torvalds [Sun, 6 Jul 2014 19:08:30 +0000 (12:08 -0700)]
Merge tag 'scsi-for-linus' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
The fixes are mostly correct value initialisations, avoiding NULL
derefs and some uninitialised pointer avoidance.
All the patches have been incubated in -next for a few days. The
final patch (use the scsi data buffer length to extract transfer size)
has been rebased to add a cc to stable, but only the commit message
has changed"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] use the scsi data buffer length to extract transfer size
virtio-scsi: fix various bad behavior on aborted requests
virtio-scsi: avoid cancelling uninitialized work items
ibmvscsi: Add memory barriers for send / receive
ibmvscsi: Abort init sequence during error recovery
qla2xxx: Fix sparse warning in qla_target.c.
bnx2fc: Improve stats update mechanism
bnx2fc: do not scan uninitialized lists in case of error.
fc: ensure scan_work isn't active when freeing fc_rport
pm8001: Fix potential null pointer dereference and memory leak.
MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
be2iscsi: remove potential junk pointer free
be2iscsi: add an missing goto in error path
scsi_error: set DID_TIME_OUT correctly
scsi_error: fix invalid setting of host byte
Linus Torvalds [Sun, 6 Jul 2014 00:13:46 +0000 (17:13 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, tda998x and vmwgfx fixes,
The main one is i915 fix for missing VGA connectors, along with some
fixes for the tda998x from Russell fixing some modesetting problems.
(still on holidays, but got a spare moment to find these)"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix incorrect write to read-only register v2:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
drm/i2c: tda998x: add some basic mode validation
drm/i2c: tda998x: faster polling for edid
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
Linus Torvalds [Sat, 5 Jul 2014 23:57:12 +0000 (16:57 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:
- A set of of OMAP patches that we had missed Tony's pull request of:
* Reset fix for am43xx
* Proper OPP table for omap5
* Fix for SoC detection of one of the DRA7 SoCs
* hwmod updates to get SATA and OCP to work on omap5 (drivers
merged in 3.16)
* ... plus a handful of smaller fixes
- sunxi needed to re-add machine specific restart code that was
removed in anticipation of a watchdog driver being merged for 3.16,
and it didn't make it in.
- Marvell fixes for PCIe on SMP and a big-endian fix.
- A trivial defconfig update to make my capri test board boot with
bcm_defconfig again.
... and a couple of MAINTAINERS updates, one to claim new Keystone
drivers that have been merged, and one to merge MXS and i.MX (both
Freescale platforms).
The largest diffs come from the hwmod code for omap5 and the re-add of
the restart code on sunxi. The hwmod stuff is quite late at this
point but it slipped through cracks repeatedly while coming up the
maintainer chain and only affects the one SoC so risk is low"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add few more Keystone drivers
MAINTAINERS: merge MXS entry into IMX one
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
ARM: bcm: Fix bcm and multi_v7 defconfigs
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
Linus Torvalds [Sat, 5 Jul 2014 23:56:14 +0000 (16:56 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
which I introduced in the last round of cleanups :("
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix memory leak when calling irq_free_hwirqs()
irqchip: spear_shirq: Fix interrupt offset
irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
irqchip: armada-370-xp: Mask all interrupts during initialization.
Sathya Prakash M R [Sat, 5 Jul 2014 23:44:57 +0000 (17:44 -0600)]
ARM: AM43xx: hwmod: add DSS hwmod data
Add DSS hwmod data for AM43xx.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
[tomi.valkeinen@ti.com: added missing dispc flags]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Felipe Balbi <balbi@ti.com> # on linux-next 5f295cdf5c5d
[paul@pwsan.com: fixed build break on AM43xx-only config]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Dave Airlie [Sat, 5 Jul 2014 21:49:59 +0000 (07:49 +1000)]
Merge tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel
Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.
* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
Dave Airlie [Sat, 5 Jul 2014 21:49:28 +0000 (07:49 +1000)]
Merge branch 'vmwgfx-fixes-3.16' of git://people.freedesktop.org/~thomash/linux
fix to a 3.15 commit.
* 'vmwgfx-fixes-3.16' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix incorrect write to read-only register v2:
Dave Airlie [Sat, 5 Jul 2014 21:48:26 +0000 (07:48 +1000)]
Merge branch 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox
mode fixes for tda998x.
* 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
drm/i2c: tda998x: add some basic mode validation
drm/i2c: tda998x: faster polling for edid
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
Keith Busch [Mon, 30 Jun 2014 22:24:44 +0000 (16:24 -0600)]
genirq: Fix memory leak when calling irq_free_hwirqs()
irq_free_hwirqs() always calls irq_free_descs() with a cnt == 0
which makes it a no-op since the interrupt count to free is
decremented in itself.
Fixes: 7b6ef1262549f6afc5c881aaef80beb8fd15f908
Signed-off-by: Keith Busch <keith.busch@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1404167084-8070-1-git-send-email-keith.busch@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Sat, 5 Jul 2014 17:12:52 +0000 (10:12 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull ARM64 fixes from Catalin Marinas:
- Exception level check at boot time (for completeness, not triggering
any bug before)
- I/D-cache synchronisation logic for huge pages
- Config symbol typo
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fix el2_setup check of CurrentEL
arm64: mm: Make icache synchronisation logic huge page aware
arm64: mm: Fix horrendous config typo
Santosh Shilimkar [Sun, 22 Jun 2014 20:06:22 +0000 (16:06 -0400)]
MAINTAINERS: Add few more Keystone drivers
Update MAINTAINERS file for recently added reset controller, AEMIF
and clocksource driver for Keystone SOCs.
The EMIF memory controller driver is also added along with AEMIF.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Shawn Guo [Wed, 2 Jul 2014 07:37:10 +0000 (15:37 +0800)]
MAINTAINERS: merge MXS entry into IMX one
The mach-mxs platform is actually co-maintained by myself and
pengutronix folks. Also it's hosted in the same kernel tree as IMX.
So let's merge the entry into IMX one.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 5 Jul 2014 04:51:19 +0000 (21:51 -0700)]
Merge tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for v3.16 (round #2)
- mvebu
- Fix PCIe deadlock now that SMP is enabled
- Fix cpuidle for big-endian systems
* tag 'mvebu-fixes-3.16-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: fix cpuidle implementation to work on big-endian systems
ARM: mvebu: update L2/PCIe deadlock workaround after L2CC cleanup
ARM: mvebu: move Armada 375 external abort logic as a quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
Maxime Ripard [Sun, 29 Jun 2014 13:48:53 +0000 (15:48 +0200)]
ARM: sunxi: Reintroduce the restart code for A10/A20 SoCs
This partly reverts commits
553600502b84 (ARM: sunxi: Remove reset code from
the platform) and
5e669ec583e2 (ARM: sunxi: Remove init_machine callback) for
the sun4i, sun5i and sun7i families.
This is needed because the watchdog counterpart of these commits was dropped,
and didn't make it into 3.16. In order to still be able to reboot the board, we
need to reintroduce that code. Of course, the long term view is still to get
rid of that code in mach-sunxi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 5 Jul 2014 04:45:38 +0000 (21:45 -0700)]
Merge tag 'omap-for-v3.16/fixes-against-rc1' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
Linus Torvalds [Fri, 4 Jul 2014 16:37:43 +0000 (09:37 -0700)]
Merge tag 'md/3.16-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Two minor bugfixes for md in 3.16"
* tag 'md/3.16-fixes' of git://neil.brown.name/md:
md: flush writes before starting a recovery.
md: make sure GET_ARRAY_INFO ioctl reports correct "clean" status
Linus Torvalds [Fri, 4 Jul 2014 15:56:57 +0000 (08:56 -0700)]
Merge tag 'sound-3.16-rc4' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup"
* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
drm/i915: provide interface for audio driver to query cdclk
ALSA: hda - Add a fixup for Thinkpad T540p
ALSA: hda - Add another headset pin quirk for some Dell machines
Linus Torvalds [Fri, 4 Jul 2014 15:53:53 +0000 (08:53 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We've queued up a few fixes in my for-linus branch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix crash when starting transaction
Btrfs: fix btrfs_print_leaf for skinny metadata
Btrfs: fix race of using total_bytes_pinned
btrfs: use E2BIG instead of EIO if compression does not help
btrfs: remove stale comment from btrfs_flush_all_pending_stuffs
Btrfs: fix use-after-free when cloning a trailing file hole
btrfs: fix null pointer dereference in btrfs_show_devname when name is null
btrfs: fix null pointer dereference in clone_fs_devices when name is null
btrfs: fix nossd and ssd_spread mount option regression
Btrfs: fix race between balance recovery and root deletion
Btrfs: atomically set inode->i_flags in btrfs_update_iflags
btrfs: only unlock block in verify_parent_transid if we locked it
Btrfs: assert send doesn't attempt to start transactions
btrfs compression: reuse recently used workspace
Btrfs: fix crash when mounting raid5 btrfs with missing disks
btrfs: create sprout should rename fsid on the sysfs as well
btrfs: dev replace should replace the sysfs entry
btrfs: dev add should add its sysfs entry
btrfs: dev delete should remove sysfs entry
btrfs: rename add_device_membership to btrfs_kobj_add_device
Marc Zyngier [Fri, 6 Jun 2014 13:16:21 +0000 (14:16 +0100)]
arm64: fix el2_setup check of CurrentEL
The CurrentEL system register reports the Current Exception Level
of the CPU. It doesn't say anything about the stack handling, and
yet we compare it to PSR_MODE_EL2t and PSR_MODE_EL2h.
It works by chance because PSR_MODE_EL2t happens to match the right
bits, but that's otherwise a very bad idea. Just check for the EL
value instead.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[catalin.marinas@arm.com: fixed arch/arm64/kernel/efi-entry.S]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tero Kristo [Tue, 4 Mar 2014 15:43:04 +0000 (17:43 +0200)]
ARM: OMAP3: control: isolate control module init to its own function
Control module related PM initializations are now moved within control
module driver. Done in preparation to isolate the code to its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Tue, 4 Mar 2014 15:24:21 +0000 (17:24 +0200)]
ARM: OMAP3: PRM: move modem reset and iva2 idle to PRM driver
Done in preparation to move PRM into its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Tue, 4 Mar 2014 15:17:06 +0000 (17:17 +0200)]
ARM: OMAP3: control: add API for setting up the modem pads
This patch moves the functionality from PM core to control driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Wed, 26 Feb 2014 15:30:43 +0000 (17:30 +0200)]
ARM: OMAP3: PRM: move PRM init code from PM core to the driver
Helps to isolate the PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Wed, 26 Feb 2014 13:31:05 +0000 (15:31 +0200)]
ARM: OMAP24xx: PRM: add API for clearing wakeup status bits
This helps to isolate the PRM into its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Wed, 26 Feb 2014 10:00:16 +0000 (12:00 +0200)]
ARM: OMAP3: PRM: add API for saving PRM scratchpad contents
This isolates the PRM register access within the PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Wed, 26 Feb 2014 09:54:29 +0000 (11:54 +0200)]
ARM: OMAP3: PRM: add API for checking and clearing cold reset status
This isolates the PRM register access within the PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Tue, 4 Mar 2014 13:48:33 +0000 (15:48 +0200)]
ARM: OMAP3: PRM: move modem reset to PRM driver
This is a more proper isolation of the code. Done in preparation of making
PRM an individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Tue, 25 Feb 2014 16:04:56 +0000 (18:04 +0200)]
ARM: OMAP3: PRM: move iva reset to PRM driver
This is a more proper isolation of the code. Done in preparation of making
PRM an individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tero Kristo [Tue, 25 Feb 2014 13:40:30 +0000 (15:40 +0200)]
ARM: OMAP3: PRM: move prcm wakeup helper to prm driver
Done in preparation to make the prm an individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Steve Capper [Wed, 2 Jul 2014 10:46:23 +0000 (11:46 +0100)]
arm64: mm: Make icache synchronisation logic huge page aware
The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.
This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org>
Tested-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> # v3.11+
Steve Capper [Wed, 25 Jun 2014 07:41:45 +0000 (08:41 +0100)]
arm64: mm: Fix horrendous config typo
The define ARM64_64K_PAGES is tested for rather than
CONFIG_ARM64_64K_PAGES. Correct that typo here.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Mengdong Lin [Thu, 3 Jul 2014 09:02:23 +0000 (17:02 +0800)]
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
For HSW/BDW display HD-A controller, hda_set_bclk() is defined to set BCLK
by programming the M/N values as per the core display clock (CDCLK) queried from
i915 display driver.
And the audio driver will also set BCLK in azx_first_init() since the display
driver can turn off the shared power in boot phase if only eDP is connected
and M/N values will be lost and must be reprogrammed.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jani Nikula [Fri, 4 Jul 2014 02:00:37 +0000 (10:00 +0800)]
drm/i915: provide interface for audio driver to query cdclk
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Fri, 4 Jul 2014 02:12:58 +0000 (19:12 -0700)]
Merge tag 'usb-3.16-rc4' of git://git./linux/kernel/git/gregkh/usb
Pull USB bugfixes from Greg KH:
"Here's a round of USB bugfixes, quirk additions, and new device ids
for 3.16-rc4. Nothing major in here at all, just a bunch of tiny
changes. All have been in linux-next with no reported issues"
* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: delete td from req's td list at ep_dequeue
usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
usb-storage/SCSI: Add broken_fua blacklist flag
usb: musb: dsps: fix the base address for accessing the mode register
tools: ffs-test: fix header values endianess
usb: phy: msm: Do not do runtime pm if the phy is not idle
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
usb: gadget: gr_udc: Fix check for invalid number of microframes
usb: musb: Fix panic upon musb_am335x module removal
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
xhci: Fix runtime suspended xhci from blocking system suspend.
xhci: clear root port wake on bits if controller isn't wake-up capable
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
xhci: Use correct SLOT ID when handling a reset device command
MAINTAINERS: update e-mail address
usb: option: add/modify Olivetti Olicard modems
USB: ftdi_sio: fix null deref at port probe
MAINTAINERS: drop two usb-serial subdriver entries
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
...
Linus Torvalds [Fri, 4 Jul 2014 02:11:48 +0000 (19:11 -0700)]
Merge tag 'staging-3.16-rc4' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver bugfixes from Greg KH:
"Nothing major here, just 4 small bugfixes that resolve some issues
reported for the IIO (staging and non-staging) and the tidspbridge
driver"
* tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: tidspbridge: fix an erroneous removal of parentheses
iio: of_iio_channel_get_by_name() returns non-null pointers for error legs
staging: iio/ad7291: fix error code in ad7291_probe()
iio:adc:ad799x: Fix reading and writing of event values, apply shift
Linus Torvalds [Fri, 4 Jul 2014 01:53:13 +0000 (18:53 -0700)]
Merge tag 'driver-core-3.16-rc4' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Well, one drivercore fix for kernfs to resolve a reported issue with
sysfs files being updated from atomic contexts, and another lz4 bugfix
for testing potential buffer overflows"
* tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
kernfs: kernfs_notify() must be useable from non-sleepable contexts
Linus Torvalds [Fri, 4 Jul 2014 01:37:25 +0000 (18:37 -0700)]
Merge tag 'trace-fixes-v3.16-rc3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg Nesterov found and fixed a bug in the perf/ftrace/uprobes code
where running:
# perf probe -x /lib/libc.so.6 syscall
# echo 1 >> /sys/kernel/debug/tracing/events/probe_libc/enable
# perf record -e probe_libc:syscall whatever
kills the uprobe. Along the way he found some other minor bugs and
clean ups that he fixed up making it a total of 4 patches.
Doing unrelated work, I found that the reading of the ftrace trace
file disables all function tracer callbacks. This was fine when
ftrace was the only user, but now that it's used by perf and kprobes,
this is a bug where reading trace can disable kprobes and perf. A
very unexpected side effect and should be fixed"
* tag 'trace-fixes-v3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove ftrace_stop/start() from reading the trace file
tracing/uprobes: Fix the usage of uprobe_buffer_enable() in probe_event_enable()
tracing/uprobes: Kill the bogus UPROBE_HANDLER_REMOVE code in uprobe_dispatcher()
uprobes: Change unregister/apply to WARN() if uprobe/consumer is gone
tracing/uprobes: Revert "Support mix of ftrace and perf"
Linus Torvalds [Fri, 4 Jul 2014 01:34:00 +0000 (18:34 -0700)]
Merge branch 'rc-fixes' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"There is one more fix for the relative paths series from -rc1: Print
the path to the build directory at the start of the build, so that
editors and IDEs can match the relative paths to source files"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Print the name of the build directory
Linus Torvalds [Fri, 4 Jul 2014 01:33:22 +0000 (18:33 -0700)]
Merge branch 'for-3.16' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"By coincidence, two NFSv4 symlink bugs, one introduced in the 3.16 xdr
encoding rewrite, the other a decoding bug that I think we've had
since the start but that just doesn't trigger very often"
* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
nfs: fix nfs4d readlink truncated packet
nfsd: fix rare symlink decoding bug
Tejun Heo [Thu, 3 Jul 2014 19:43:15 +0000 (15:43 -0400)]
ptrace,x86: force IRET path after a ptrace_stop()
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Kroah-Hartman [Thu, 3 Jul 2014 23:06:57 +0000 (16:06 -0700)]
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
Jan points out that I forgot to make the needed fixes to the
lz4_uncompress_unknownoutputsize() function to mirror the changes done
in lz4_decompress() with regards to potential pointer overflows.
The only in-kernel user of this function is the zram code, which only
takes data from a valid compressed buffer that it made itself, so it's
not a big issue. But due to external kernel modules using this
function, it's better to be safe here.
Reported-by: Jan Beulich <JBeulich@suse.com>
Cc: "Don A. Bailey" <donb@securitymouse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Thu, 3 Jul 2014 18:04:27 +0000 (11:04 -0700)]
Merge remote-tracking branch 'scsi-queue/drivers-for-3.16' into for-linus
Martin K. Petersen [Tue, 24 Jun 2014 14:59:35 +0000 (16:59 +0200)]
[SCSI] use the scsi data buffer length to extract transfer size
Commit
8846bab180fa introduced a helper that can be used to query the
wire transfer size for a SCSI command taking protection information into
account.
However, some commands do not have a 1:1 mapping between the block range
they work on and the payload size (discard, write same). After the
scatterlist has been set up these requests use __data_len to store the
number of bytes to report completion on. This means that callers of
scsi_transfer_length() would get the wrong byte count for these types of
requests.
To overcome this we make scsi_transfer_length() use the scatterlist
length in the scsi_data_buffer as basis for the wire transfer
calculation instead of __data_len.
Reported-by: Christoph Hellwig <hch@infradead.org>
Debugged-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Fixes: d77e65350f2d82dfa0557707d505711f5a43c8fd
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Thu, 3 Jul 2014 16:22:00 +0000 (09:22 -0700)]
Merge branch 'akpm' (patches from Andrew Morton)
Merge fixes from Andrew Morton:
"14 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
shmem: fix init_page_accessed use to stop !PageLRU bug
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
fs/seq_file: fallback to vmalloc allocation
/proc/stat: convert to single_open_size()
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
msync: fix incorrect fstart calculation
zram: revalidate disk after capacity change
tools: memory-hotplug fix unexpected operator error
tools: cpu-hotplug fix unexpected operator error
autofs4: fix false positive compile error
slub: fix off by one in number of slab tests
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
Hugh Dickins [Wed, 2 Jul 2014 22:22:38 +0000 (15:22 -0700)]
shmem: fix init_page_accessed use to stop !PageLRU bug
Under shmem swapping load, I sometimes hit the VM_BUG_ON_PAGE(!PageLRU)
in isolate_lru_pages() at mm/vmscan.c:1281!
Commit
2457aec63745 ("mm: non-atomically mark page accessed during page
cache allocation where possible") looks like interrupted work-in-progress.
mm/filemap.c's call to init_page_accessed() is fine, but not mm/shmem.c's
- shmem_write_begin() is clearly wrong to use it after shmem_getpage(),
when the page is always visible in radix_tree, and often already on LRU.
Revert change to shmem_write_begin(), and use init_page_accessed() or
mark_page_accessed() appropriately for SGP_WRITE in shmem_getpage_gfp().
SGP_WRITE also covers shmem_symlink(), which did not mark_page_accessed()
before; but since many other filesystems use [__]page_symlink(), which did
and does mark the page accessed, consider this as rectifying an oversight.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Wed, 2 Jul 2014 22:22:38 +0000 (15:22 -0700)]
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
Revert commit
939f04bec1a4 ("printk: enable interrupts before calling
console_trylock_for_printk()").
Andreas reported:
: None of the post 3.15 kernel boot for me. They all hang at the GRUB
: screen telling me it loaded and started the kernel, but the kernel
: itself stops before it prints anything (or even replaces the GRUB
: background graphics).
939f04bec1a4 is modest latency reduction. Revert it until we understand
the reason for these failures.
Reported-by: Andreas Bombe <aeb@debian.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shuah Khan [Wed, 2 Jul 2014 22:22:37 +0000 (15:22 -0700)]
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
The test fails in the middle when it is not run as root while accessing
/proc/sys/kernel/msg_next_id. Changed it to check for root at the
beginning of the test and exit if not root.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Carstens [Wed, 2 Jul 2014 22:22:37 +0000 (15:22 -0700)]
fs/seq_file: fallback to vmalloc allocation
There are a couple of seq_files which use the single_open() interface.
This interface requires that the whole output must fit into a single
buffer.
E.g. for /proc/stat allocation failures have been observed because an
order-4 memory allocation failed due to memory fragmentation. In such
situations reading /proc/stat is not possible anymore.
Therefore change the seq_file code to fallback to vmalloc allocations
which will usually result in a couple of order-0 allocations and hence
also work if memory is fragmented.
For reference a call trace where reading from /proc/stat failed:
sadc: page allocation failure: order:4, mode:0x1040d0
CPU: 1 PID: 192063 Comm: sadc Not tainted 3.10.0-123.el7.s390x #1
[...]
Call Trace:
show_stack+0x6c/0xe8
warn_alloc_failed+0xd6/0x138
__alloc_pages_nodemask+0x9da/0xb68
__get_free_pages+0x2e/0x58
kmalloc_order_trace+0x44/0xc0
stat_open+0x5a/0xd8
proc_reg_open+0x8a/0x140
do_dentry_open+0x1bc/0x2c8
finish_open+0x46/0x60
do_last+0x382/0x10d0
path_openat+0xc8/0x4f8
do_filp_open+0x46/0xa8
do_sys_open+0x114/0x1f0
sysc_tracego+0x14/0x1a
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tested-by: David Rientjes <rientjes@google.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Thorsten Diehl <thorsten.diehl@de.ibm.com>
Cc: Andrea Righi <andrea@betterlinux.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Carstens [Wed, 2 Jul 2014 22:22:37 +0000 (15:22 -0700)]
/proc/stat: convert to single_open_size()
These two patches are supposed to "fix" failed order-4 memory
allocations which have been observed when reading /proc/stat. The
problem has been observed on s390 as well as on x86.
To address the problem change the seq_file memory allocations to
fallback to use vmalloc, so that allocations also work if memory is
fragmented.
This approach seems to be simpler and less intrusive than changing
/proc/stat to use an interator. Also it "fixes" other users as well,
which use seq_file's single_open() interface.
This patch (of 2):
Use seq_file's single_open_size() to preallocate a buffer that is large
enough to hold the whole output, instead of open coding it. Also
calculate the requested size using the number of online cpus instead of
possible cpus, since the size of the output only depends on the number
of online cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Thorsten Diehl <thorsten.diehl@de.ibm.com>
Cc: Andrea Righi <andrea@betterlinux.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chen Yucong [Wed, 2 Jul 2014 22:22:37 +0000 (15:22 -0700)]
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
Until now, the kernel has the same policy to handle victimized page
frames that belong to kernel-space(reserved/slab-subsystem) or
non-LRU(unknown page state). In other word, the result of handling
either of these victimized page frames is (IGNORED | FAILED), and the
return value of memory_failure() is -EBUSY.
This patch is to avoid that memory_failure() returns very soon due to
the "true" value of (!PageLRU(p)), and it also ensures that
action_result() can report more precise information("reserved kernel",
"kernel slab", and "unknown page state") instead of "non LRU",
especially for memory errors which are detected by memory-scrubbing.
Andi said:
: While running the mcelog test suite on 3.14 I hit the following VM_BUG_ON:
:
: soft_offline: 0x56d4: unknown non LRU page type
3ffff800008000
: page:
ffffea000015b400 count:3 mapcount:
2097169 mapping: (null) index:0xffff8800056d7000
: page flags: 0x3ffff800004081(locked|slab|head)
: ------------[ cut here ]------------
: kernel BUG at mm/rmap.c:1495!
:
: I think what happened is that a LRU page turned into a slab page in
: parallel with offlining. memory_failure initially tests for this case,
: but doesn't retest later after the page has been locked.
:
: ...
:
: I ran this patch in a loop over night with some stress plus
: the mcelog test suite running in a loop. I cannot guarantee it hit it,
: but it should have given it a good beating.
:
: The kernel survived with no messages, although the mcelog test suite
: got killed at some point because it couldn't fork anymore. Probably
: some unrelated problem.
:
: So the patch is ok for me for .16.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chen Yucong [Wed, 2 Jul 2014 22:22:36 +0000 (15:22 -0700)]
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
When using trace-vmscan-postprocess.pl for checking the file/anon rate
of scanning, we can find that it can not be performed. At the same
time, the following message will be reported:
WARNING: Format not as expected for event vmscan/mm_vmscan_lru_isolate
'file' != 'contig_taken' Fewer fields than expected in format at
./trace-vmscan-postprocess.pl line 171, <FORMAT> line 76.
In trace-vmscan-postprocess.pl, (contig_taken, contig_dirty, and
contig_failed) are be associated respectively to (nr_lumpy_taken,
nr_lumpy_dirty, and nr_lumpy_failed) for lumpy reclaim. Via commit
c53919adc045 ("mm: vmscan: remove lumpy reclaim"), lumpy reclaim had
already been removed by Mel, but the update for
trace-vmscan-postprocess.pl was missed.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Namjae Jeon [Wed, 2 Jul 2014 22:22:36 +0000 (15:22 -0700)]
msync: fix incorrect fstart calculation
Fix a regression caused by
7fc34a62ca44 ("mm/msync.c: sync only the
requested range in msync()").
xfstests generic/075 fail occured on ext4 data=journal mode because the
intended range was not syncing due to wrong fstart calculation.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Reported-by: Eric Whitney <enwlinux@gmail.com>
Tested-by: Eric Whitney <enwlinux@gmail.com>
Acked-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Tested-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Wed, 2 Jul 2014 22:22:36 +0000 (15:22 -0700)]
zram: revalidate disk after capacity change
Alexander reported mkswap on /dev/zram0 is failed if other process is
opening the block device file.
Step is as follows,
0. Reset the unused zram device.
1. Use a program that opens /dev/zram0 with O_RDWR and sleeps
until killed.
2. While that program sleeps, echo the correct value to
/sys/block/zram0/disksize.
3. Verify (e.g. in /proc/partitions) that the disk size is applied
correctly. It is.
4. While that program still sleeps, attempt to mkswap /dev/zram0.
This fails: mkswap: error: swap area needs to be at least 40 KiB
When I investigated, the size get by ioctl(fd, BLKGETSIZE64, xxx) on
mkswap to get a size of blockdev was zero although zram0 has right size by
2.
The reason is zram didn't revalidate disk after changing capacity so that
size of blockdev's inode is not uptodate until all of file is close.
This patch should fix the BUG.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Tested-by: Alexander E. Patrakov <patrakov@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shuah Khan [Wed, 2 Jul 2014 22:22:36 +0000 (15:22 -0700)]
tools: memory-hotplug fix unexpected operator error
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
./on-off-test.sh: 9: [: !=: unexpected operator
Change Makefile to use bash instead.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shuah Khan [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
tools: cpu-hotplug fix unexpected operator error
on-off-test uses "$UID != 0" to test for root, but $UID is a construct
specific to bash. Using /bin/sh that isn't bash results in the
following error (due to the "$UID" part expanding to nothing):
./on-off-test.sh: 9: [: !=: unexpected operator
Change Makefile to use bash instead.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Kent [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
autofs4: fix false positive compile error
On strict build environments we can see:
fs/autofs4/inode.c: In function 'autofs4_fill_super':
fs/autofs4/inode.c:312: error: 'pgrp' may be used uninitialized in this function
make[2]: *** [fs/autofs4/inode.o] Error 1
make[1]: *** [fs/autofs4] Error 2
make: *** [fs] Error 2
make: *** Waiting for unfinished jobs....
This is due to the use of pgrp_set being used to indicate pgrp has has
been set rather than initializing pgrp itself.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
slub: fix off by one in number of slab tests
min_partial means minimum number of slab cached in node partial list.
So, if nr_partial is less than it, we keep newly empty slab on node
partial list rather than freeing it. But if nr_partial is equal or
greater than it, it means that we have enough partial slabs so should
free newly empty slab. Current implementation missed the equal case so
if we set min_partial is 0, then, at least one slab could be cached.
This is critical problem to kmemcg destroying logic because it doesn't
works properly if some slabs is cached. This patch fixes this problem.
Fixes
91cb69620284 ("slub: make dead memcg caches discard free slabs
immediately").
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Nazarewicz [Wed, 2 Jul 2014 22:22:35 +0000 (15:22 -0700)]
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE,
the following is triggered at early boot:
SMP: Total of 8 processors activated.
devtmpfs: initialized
Unable to handle kernel NULL pointer dereference at virtual address
00000008
pgd =
fffffe0000050000
[
00000008] *pgd=
00000043fba00003, *pmd=
00000043fba00003, *pte=
00e0000078010407
Internal error: Oops:
96000006 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44
task:
fffffe03bc040000 ti:
fffffe03bc080000 task.ti:
fffffe03bc080000
PC is at __list_add+0x10/0xd4
LR is at free_one_page+0x270/0x638
...
Call trace:
__list_add+0x10/0xd4
free_one_page+0x26c/0x638
__free_pages_ok.part.52+0x84/0xbc
__free_pages+0x74/0xbc
init_cma_reserved_pageblock+0xe8/0x104
cma_init_reserved_areas+0x190/0x1e4
do_one_initcall+0xc4/0x154
kernel_init_freeable+0x204/0x2a8
kernel_init+0xc/0xd4
This happens because init_cma_reserved_pageblock() calls
__free_one_page() with pageblock_order as page order but it is bigger
than MAX_ORDER. This in turn causes accesses past zone->free_list[].
Fix the problem by changing init_cma_reserved_pageblock() such that it
splits pageblock into individual MAX_ORDER pages if pageblock is bigger
than a MAX_ORDER page.
In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all
architectures expect for ia64, powerpc and tile at the moment, the
â
\80\9cpageblock_order > MAX_ORDERâ
\80\9d condition will be optimised out since both
sides of the operator are constants. In cases where pageblock size is
variable, the performance degradation should not be significant anyway
since init_cma_reserved_pageblock() is called only at boot time at most
MAX_CMA_AREAS times which by default is eight.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> [3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filipe Manana [Tue, 24 Jun 2014 16:46:58 +0000 (17:46 +0100)]
Btrfs: fix crash when starting transaction
Often when starting a transaction we commit the currently running transaction,
which can end up writing block group caches when the current process has its
journal_info set to NULL (and not to a transaction). This makes our assertion
at btrfs_check_data_free_space() (current_journal != NULL) fail, resulting
in a crash/hang. Therefore fix it by setting journal_info.
Two different traces of this issue follow below.
1)
[51502.241936] BTRFS: assertion failed: current->journal_info, file: fs/btrfs/extent-tree.c, line: 3670
[51502.242213] ------------[ cut here ]------------
[51502.242493] kernel BUG at fs/btrfs/ctree.h:3964!
[51502.242669] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
(...)
[51502.244010] Call Trace:
[51502.244010] [<
ffffffffa02bc025>] btrfs_check_data_free_space+0x395/0x3a0 [btrfs]
[51502.244010] [<
ffffffffa02c3bdc>] btrfs_write_dirty_block_groups+0x4ac/0x640 [btrfs]
[51502.244010] [<
ffffffffa0357a6a>] commit_cowonly_roots+0x164/0x226 [btrfs]
[51502.244010] [<
ffffffffa02d53cd>] btrfs_commit_transaction+0x4ed/0xab0 [btrfs]
[51502.244010] [<
ffffffff8168ec7b>] ? _raw_spin_unlock+0x2b/0x40
[51502.244010] [<
ffffffffa02d6259>] start_transaction+0x459/0x620 [btrfs]
[51502.244010] [<
ffffffffa02d67ab>] btrfs_start_transaction+0x1b/0x20 [btrfs]
[51502.244010] [<
ffffffffa02d73e1>] __unlink_start_trans+0x31/0xe0 [btrfs]
[51502.244010] [<
ffffffffa02dea67>] btrfs_unlink+0x37/0xc0 [btrfs]
[51502.244010] [<
ffffffff811bb054>] ? do_unlinkat+0x114/0x2a0
[51502.244010] [<
ffffffff811baebc>] vfs_unlink+0xcc/0x150
[51502.244010] [<
ffffffff811bb1a0>] do_unlinkat+0x260/0x2a0
[51502.244010] [<
ffffffff811a9ef4>] ? filp_close+0x64/0x90
[51502.244010] [<
ffffffff810aaea6>] ? trace_hardirqs_on_caller+0x16/0x1e0
[51502.244010] [<
ffffffff81349cab>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[51502.244010] [<
ffffffff811be9eb>] SyS_unlinkat+0x1b/0x40
[51502.244010] [<
ffffffff81698452>] system_call_fastpath+0x16/0x1b
[51502.244010] Code: 0b 55 48 89 e5 0f 0b 55 48 89 e5 0f 0b 55 89 f1 48 c7 c2 71 13 36 a0 48 89 fe 31 c0 48 c7 c7 b8 43 36 a0 48 89 e5 e8 5d b0 32 e1 <0f> 0b 0f 1f 44 00 00 55 b9 11 00 00 00 48 89 e5 41 55 49 89 f5
[51502.244010] RIP [<
ffffffffa03575da>] assfail.constprop.88+0x1e/0x20 [btrfs]
2)
[25405.097230] BTRFS: assertion failed: current->journal_info, file: fs/btrfs/extent-tree.c, line: 3670
[25405.097488] ------------[ cut here ]------------
[25405.097767] kernel BUG at fs/btrfs/ctree.h:3964!
[25405.097940] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
(...)
[25405.100008] Call Trace:
[25405.100008] [<
ffffffffa02bc025>] btrfs_check_data_free_space+0x395/0x3a0 [btrfs]
[25405.100008] [<
ffffffffa02c3bdc>] btrfs_write_dirty_block_groups+0x4ac/0x640 [btrfs]
[25405.100008] [<
ffffffffa035755a>] commit_cowonly_roots+0x164/0x226 [btrfs]
[25405.100008] [<
ffffffffa02d53cd>] btrfs_commit_transaction+0x4ed/0xab0 [btrfs]
[25405.100008] [<
ffffffff8109c170>] ? bit_waitqueue+0xc0/0xc0
[25405.100008] [<
ffffffffa02d6259>] start_transaction+0x459/0x620 [btrfs]
[25405.100008] [<
ffffffffa02d67ab>] btrfs_start_transaction+0x1b/0x20 [btrfs]
[25405.100008] [<
ffffffffa02e3407>] btrfs_create+0x47/0x210 [btrfs]
[25405.100008] [<
ffffffffa02d74cc>] ? btrfs_permission+0x3c/0x80 [btrfs]
[25405.100008] [<
ffffffff811bc63b>] vfs_create+0x9b/0x130
[25405.100008] [<
ffffffff811bcf19>] do_last+0x849/0xe20
[25405.100008] [<
ffffffff811b9409>] ? link_path_walk+0x79/0x820
[25405.100008] [<
ffffffff811bd5b5>] path_openat+0xc5/0x690
[25405.100008] [<
ffffffff810ab07d>] ? trace_hardirqs_on+0xd/0x10
[25405.100008] [<
ffffffff811cdcd2>] ? __alloc_fd+0x32/0x1d0
[25405.100008] [<
ffffffff811be2a3>] do_filp_open+0x43/0xa0
[25405.100008] [<
ffffffff811cddf1>] ? __alloc_fd+0x151/0x1d0
[25405.100008] [<
ffffffff811abcfc>] do_sys_open+0x13c/0x230
[25405.100008] [<
ffffffff810aaea6>] ? trace_hardirqs_on_caller+0x16/0x1e0
[25405.100008] [<
ffffffff811abe12>] SyS_open+0x22/0x30
[25405.100008] [<
ffffffff81698452>] system_call_fastpath+0x16/0x1b
[25405.100008] Code: 0b 55 48 89 e5 0f 0b 55 48 89 e5 0f 0b 55 89 f1 48 c7 c2 51 13 36 a0 48 89 fe 31 c0 48 c7 c7 d0 43 36 a0 48 89 e5 e8 6d b5 32 e1 <0f> 0b 0f 1f 44 00 00 55 b9 11 00 00 00 48 89 e5 41 55 49 89 f5
[25405.100008] RIP [<
ffffffffa03570ca>] assfail.constprop.88+0x1e/0x20 [btrfs]
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Josef Bacik [Wed, 2 Jul 2014 17:20:48 +0000 (10:20 -0700)]
Btrfs: fix btrfs_print_leaf for skinny metadata
We wouldn't actuall print the extent information if we had a skinny metadata
item, this fixes that. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Liu Bo [Wed, 2 Jul 2014 08:58:01 +0000 (16:58 +0800)]
Btrfs: fix race of using total_bytes_pinned
This percpu counter @total_bytes_pinned is introduced to skip unnecessary
operations of 'commit transaction', it accounts for those space we may free
but are stuck in delayed refs.
And we zero out @space_info->total_bytes_pinned every transaction period so
we have a better idea of how much space we'll actually free up by committing
this transaction. However, we do the 'zero out' part a little earlier, before
we actually unpin space, so we end up returning ENOSPC when we actually have
free space that's just unpinned from committing transaction.
xfstests/generic/074 complained then.
This fixes it by actually accounting the percpu pinned number when 'unpin',
and since it's protected by space_info->lock, the race is gone now.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
This page took 0.054231 seconds and 5 git commands to generate.