Linus Torvalds [Fri, 14 Sep 2012 22:34:07 +0000 (15:34 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Use after free and new device IDs in bluetooth from Andre Guedes,
Yevgeniy Melnichuk, Gustavo Padovan, and Henrik Rydberg.
2) Fix crashes with short packet lengths and VLAN in pktgen, from
Nishank Trivedi.
3) mISDN calls flush_work_sync() with locks held, fix from Karsten
Keil.
4) Packet scheduler gred parameters are reported to userspace
improperly scaled, and WRED idling is not performed correctly. All
from David Ward.
5) Fix TCP socket refcount problem in ipv6, from Julian Anastasov.
6) ibmveth device has RX queue alignment requirements which are not
being explicitly met resulting in sporadic failures, fix from
Santiago Leon.
7) Netfilter needs to take care when interpreting sockets attached to
socket buffers, they could be time-wait minisockets. Fix from Eric
Dumazet.
8) sock_edemux() has the same issue as netfilter did in #7 above, fix
from Eric Dumazet.
9) Avoid infinite loops in CBQ scheduler with some configurations, from
Eric Dumazet.
10) Deal with "Reflection scan: an Off-Path Attack on TCP", from Jozsef
Kadlecsik.
11) SCTP overcharges socket for TX packets, fix from Thomas Graf.
12) CODEL packet scheduler should not reset it's state every time it
builds a new flow, fix from Eric Dumazet.
13) Fix memory leak in nl80211, from Wei Yongjun.
14) NETROM doesn't check skb_copy_datagram_iovec() return values, from
Alan Cox.
15) l2tp ethernet was using sizeof(ETH_HLEN) instead of plain ETH_HLEN,
oops. From Eric Dumazet.
16) Fix selection of ath9k chips on which PA linearization and AM2PM
predistoration are used, from Felix Fietkau.
17) Flow steering settings in mlx4 driver need to be validated properly,
from Hadar Hen Zion.
18) bnx2x doesn't show the correct link duplex setting, from Yaniv
Rosner.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
pktgen: fix crash with vlan and packet size less than 46
bnx2x: Add missing afex code
bnx2x: fix registers dumped
bnx2x: correct advertisement of pause capabilities
bnx2x: display the correct duplex value
bnx2x: prevent timeouts when using PFC
bnx2x: fix stats copying logic
bnx2x: Avoid sending multiple statistics queries
net: qmi_wwan: call subdriver with control intf only
net_sched: gred: actually perform idling in WRED mode
net_sched: gred: fix qave reporting via netlink
net_sched: gred: eliminate redundant DP prio comparisons
net_sched: gred: correct comment about qavg calculation in RIO mode
mISDN: Fix wrong usage of flush_work_sync while holding locks
netfilter: log: Fix log-level processing
net-sched: sch_cbq: avoid infinite loop
net: qmi_wwan: fix Gobi device probing for un2430
net: fix net/core/sock.c build error
ixp4xx_hss: fix build failure due to missing linux/module.h inclusion
caif: move the dereference below the NULL test
...
Linus Torvalds [Fri, 14 Sep 2012 21:54:57 +0000 (14:54 -0700)]
Merge tag 'usb-3.6-rc6' of git://git./linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of USB patches, a bit more than I normally like this
late in the -rc series, but given people's vacations (myself
included), and the kernel summit, it seems to have happened this way.
All are tiny, but they add up. A number of gadget and xhci fixes, and
a few new device ids. All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: don't stall endpoint if request list is empty in isr_tr_complete_low
usb: chipidea: cleanup dma_pool if udc_start() fails
usb: chipidea: udc: fix error path in udc_start()
usb: chipidea: udc: add pullup fuction, needed by the uvc gadget
usb: chipidea: udc: fix setup of endpoint maxpacket size
USB: option: replace ZTE K5006-Z entry with vendor class rule
EHCI: Update qTD next pointer in QH overlay region during unlink
USB: cdc-wdm: fix wdm_find_device* return value
USB: ftdi_sio: do not claim CDC ACM function
usb: dwc3: gadget: fix pending isoc handling
usb: renesas_usbhs: fixup DMA transport data alignment
usb: gadget: at91udc: Don't check for ep->ep.desc
usb: gadget: at91udc: don't overwrite driver data
usb: dwc3: core: fix incorrect usage of resource pointer
usb: musb: musbhsdma: fix IRQ check
usb: musb: tusb6010: fix error path in tusb_probe()
usb: musb: host: fix for musb_start_urb Oops
usb: gadget: dummy_hcd: add support for USB_DT_BOS on rh
usb: gadget: dummy_hcd: fixup error probe path
usb: gadget: s3c-hsotg.c: fix error return code
...
Linus Torvalds [Fri, 14 Sep 2012 21:54:29 +0000 (14:54 -0700)]
Merge tag 'tty-3.6-rc6' of git://git./linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are 2 tiny patches for a serial driver to resolve issues that
people have reported with the 3.6-rc tree.
Both of these have been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: don't reinit clock in imx_setup_ufcr()
tty: serial: imx: console write routing is unsafe on SMP
Linus Torvalds [Fri, 14 Sep 2012 21:53:51 +0000 (14:53 -0700)]
Merge tag 'staging-3.6-rc6' of git://git./linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are a few staging tree fixes for problems that have been
reported.
Nothing major, just a number of tiny driver fixes. All of these have
been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
drm/omap: add more new timings fields
drm/omap: update for interlaced
staging: r8712u: fix bug in r8712_recv_indicatepkt()
staging: zcache: fix cleancache race condition with shrinker
Staging: Android alarm: IOCTL command encoding fix
staging: vt6656: [BUG] - Failed connection, incorrect endian.
staging: ozwpan: fix memcmp() test in oz_set_active_pd()
staging: wlan-ng: Fix problem with wrong arguments
staging: comedi: das08: Correct AO output for das08jr-16-ao
staging: comedi: das08: Correct AI encoding for das08jr-16-ao
staging: comedi: das08: Fix PCI ref count
staging: comedi: amplc_pci230: Fix PCI ref count
staging: comedi: amplc_pc263: Fix PCI ref count
staging: comedi: amplc_pc236: Fix PCI ref count
staging: comedi: amplc_dio200: Fix PCI ref count
staging: comedi: amplc_pci224: Fix PCI ref count
drivers/iio/adc/at91_adc.c: adjust inconsistent IS_ERR and PTR_ERR
staging iio: fix potential memory leak in lis3l02dq_ring.c
staging:iio: prevent divide by zero bugs
Linus Torvalds [Fri, 14 Sep 2012 21:53:22 +0000 (14:53 -0700)]
Merge tag 'driver-core-3.6-rc6' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg Kroah-Hartman:
"Here is one fix for 3.6-rc6 for the kobject.h file.
It fixes a reported oops if CONFIG_HOTPLUG is disabled. It's been in
the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix oops with "input0: bad kobj_uevent_env content in show_uevent()"
Linus Torvalds [Fri, 14 Sep 2012 21:48:21 +0000 (14:48 -0700)]
vfs: make O_PATH file descriptors usable for 'fstat()'
We already use them for openat() and friends, but fstat() also wants to
be able to use O_PATH file descriptors. This should make it more
directly comparable to the O_SEARCH of Solaris.
Note that you could already do the same thing with "fstatat()" and an
empty path, but just doing "fstat()" directly is simpler and faster, so
there is no reason not to just allow it directly.
See also commit
332a2e1244bd, which did the same thing for fchdir, for
the same reasons.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # O_PATH introduced in 3.0+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nishank Trivedi [Wed, 12 Sep 2012 13:32:49 +0000 (13:32 +0000)]
pktgen: fix crash with vlan and packet size less than 46
If vlan option is being specified in the pktgen and packet size
being requested is less than 46 bytes, despite being illogical
request, pktgen should not crash the kernel.
BUG: unable to handle kernel paging request at
ffff88021fb82000
Process kpktgend_0 (pid: 1184, threadinfo
ffff880215f1a000, task
ffff880218544530)
Call Trace:
[<
ffffffffa0637cd2>] ? pktgen_finalize_skb+0x222/0x300 [pktgen]
[<
ffffffff814f0084>] ? build_skb+0x34/0x1c0
[<
ffffffffa0639b11>] pktgen_thread_worker+0x5d1/0x1790 [pktgen]
[<
ffffffffa03ffb10>] ? igb_xmit_frame_ring+0xa30/0xa30 [igb]
[<
ffffffff8107ba20>] ? wake_up_bit+0x40/0x40
[<
ffffffff8107ba20>] ? wake_up_bit+0x40/0x40
[<
ffffffffa0639540>] ? spin+0x240/0x240 [pktgen]
[<
ffffffff8107b4e3>] kthread+0x93/0xa0
[<
ffffffff81615de4>] kernel_thread_helper+0x4/0x10
[<
ffffffff8107b450>] ? flush_kthread_worker+0x80/0x80
[<
ffffffff81615de0>] ? gs_change+0x13/0x13
The root cause of why pktgen is not able to handle this case is due
to comparison of signed (datalen) and unsigned data (sizeof), which
eventually passes a huge number to skb_put().
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Tue, 11 Sep 2012 04:34:14 +0000 (04:34 +0000)]
bnx2x: Add missing afex code
Commit
a334872224a67b614dc888460377862621f3dac7 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 11 Sep 2012 04:34:13 +0000 (04:34 +0000)]
bnx2x: fix registers dumped
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Tue, 11 Sep 2012 04:34:12 +0000 (04:34 +0000)]
bnx2x: correct advertisement of pause capabilities
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Tue, 11 Sep 2012 04:34:11 +0000 (04:34 +0000)]
bnx2x: display the correct duplex value
Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Tue, 11 Sep 2012 04:34:10 +0000 (04:34 +0000)]
bnx2x: prevent timeouts when using PFC
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Tue, 11 Sep 2012 04:34:09 +0000 (04:34 +0000)]
bnx2x: fix stats copying logic
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Tue, 11 Sep 2012 04:34:08 +0000 (04:34 +0000)]
bnx2x: Avoid sending multiple statistics queries
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Wed, 12 Sep 2012 20:44:35 +0000 (20:44 +0000)]
net: qmi_wwan: call subdriver with control intf only
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit
230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Thu, 13 Sep 2012 05:22:35 +0000 (05:22 +0000)]
net_sched: gred: actually perform idling in WRED mode
gred_dequeue() and gred_drop() do not seem to get called when the
queue is empty, meaning that we never start idling while in WRED
mode. And since qidlestart is not stored by gred_store_wred_set(),
we would never stop idling while in WRED mode if we ever started.
This messes up the average queue size calculation that influences
packet marking/dropping behavior.
Now, we start WRED mode idling as we are removing the last packet
from the queue. Also we now actually stop WRED mode idling when we
are enqueuing a packet.
Cc: Bruce Osler <brosler@cisco.com>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Thu, 13 Sep 2012 05:22:34 +0000 (05:22 +0000)]
net_sched: gred: fix qave reporting via netlink
q->vars.qavg is a Wlog scaled value, but q->backlog is not. In order
to pass q->vars.qavg as the backlog value, we need to un-scale it.
Additionally, the qave value returned via netlink should not be Wlog
scaled, so we need to un-scale the result of red_calc_qavg().
This caused artificially high values for "Average Queue" to be shown
by 'tc -s -d qdisc', but did not affect the actual operation of GRED.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Thu, 13 Sep 2012 05:22:33 +0000 (05:22 +0000)]
net_sched: gred: eliminate redundant DP prio comparisons
Each pair of DPs only needs to be compared once when searching for
a non-unique prio value.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Thu, 13 Sep 2012 05:22:32 +0000 (05:22 +0000)]
net_sched: gred: correct comment about qavg calculation in RIO mode
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Thu, 13 Sep 2012 04:36:20 +0000 (04:36 +0000)]
mISDN: Fix wrong usage of flush_work_sync while holding locks
It is a bad idea to hold a spinlock and call flush_work_sync.
Move the workqueue cleanup outside the spinlock and use cancel_work_sync,
on closing the channel this seems to be the more correct function.
Remove the never used and constant return value of mISDN_freebchannel.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 13 Sep 2012 17:53:06 +0000 (13:53 -0400)]
Merge branch 'master' of git://1984.lsi.us.es/nf
Pablo Neira Ayuso say:
====================
The following patchset contains four updates for your net tree, they are:
* Fix crash on timewait sockets, since the TCP early demux was added,
in nfnetlink_log, from Eric Dumazet.
* Fix broken syslog log-level for xt_LOG and ebt_log since printk format was
converted from <.> to a 2 bytes pattern using ASCII SOH, from Joe Perches.
* Two security fixes for the TCP connection tracking targeting off-path attacks,
from Jozsef Kadlecsik. The problem was discovered by Jan Wrobel and it is
documented in: http://mixedbit.org/reflection_scan/reflection_scan.pdf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 13 Sep 2012 11:51:41 +0000 (19:51 +0800)]
Merge tag 'sound-3.6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few small / trivial regression fixes at this time."
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: ice1724: Use linear scale for AK4396 volume control.
ALSA: hda_intel: add position_fix quirk for Asus K53E
ALSA: compress_core: fix open flags test in snd_compr_open()
ALSA: hda - Fix Oops at codec reset/reconfig
ALSA: usb-audio: Fix bogus error messages for delay accounting
ALSA: hda - Fix missing Master volume for STAC9200/925x
Linus Torvalds [Thu, 13 Sep 2012 11:10:50 +0000 (19:10 +0800)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Olof Johansson:
- A set of OMAP fixes, about half of them PM/clock related, the rest
scattered over the platform code but all small and targeted to real
bugs.
- Two small i.MX fixes for SSI device clock setup.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: clk-imx35: Fix SSI clock registration
ARM: clk-imx25: Fix SSI clock registration
ARM: OMAP4: Fix array size for irq_target_cpu
ARM: OMAP4: hwmod data: temporarily comment out data for the sl2if IP block
ARM: OMAP: hwmod code: Disable module when hwmod enable fails
ARM: OMAP3: hwmod data: fix iva2 reset info
ARM: OMAP3xxx: clockdomain: fix software supervised wakeup/sleep
ARM: OMAP2+: am33xx: Fix the timer fck clock naming convention
ARM: OMAP: Config fix for omap3-touchbook board
ARM: OMAP: sram: skip the first 16K on OMAP3 HS
ARM: OMAP: sram: fix OMAP4 errata handling
ARM: OMAP: timer: obey the !CONFIG_OMAP_32K_TIMER
Linus Torvalds [Thu, 13 Sep 2012 11:07:15 +0000 (19:07 +0800)]
Merge tag 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
Pull additional AHCI PCI IDs from Jeff Garzik.
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Add identifiers for ASM106x devices
ahci: Add alternate identifier for the 88SE9172
ahci: Add JMicron 362 device IDs
Olof Johansson [Thu, 13 Sep 2012 05:00:07 +0000 (22:00 -0700)]
Merge tag 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6 into fixes
ARM: i.MX: Fix SSI clock associations for i.MX25/i.MX35
* tag 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: clk-imx35: Fix SSI clock registration
ARM: clk-imx25: Fix SSI clock registration
+ Linux 3.6-rc5
Alan Cox [Tue, 4 Sep 2012 15:25:25 +0000 (16:25 +0100)]
ahci: Add identifiers for ASM106x devices
They don't always appear as AHCI class devices but instead as IDE class.
Based on an initial patch by Hiroaki Nito
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42804
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Tue, 4 Sep 2012 15:07:18 +0000 (16:07 +0100)]
ahci: Add alternate identifier for the 88SE9172
This can also appear as 0x9192. Reported in bugzilla and confirmed with the
board documentation for these boards.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: The Stables <stable@vger.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 10 Sep 2012 00:09:04 +0000 (01:09 +0100)]
ahci: Add JMicron 362 device IDs
The JMicron JMB362 controller supports AHCI only, but some revisions
use the IDE class code. These need to be matched by device ID.
These additions have apparently been included by QNAP in their NAS
devices using these controllers.
References: http://bugs.debian.org/634180
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dmitry Kasatkin [Wed, 12 Sep 2012 10:26:55 +0000 (13:26 +0300)]
digsig: add hash size comparision on signature verification
When pkcs_1_v1_5_decode_emsa() returns without error and hash sizes do
not match, hash comparision is not done and digsig_verify_rsa() returns
no error. This is a bug and this patch fixes it.
The bug was introduced in v3.3 by commit
b35e286a640f ("lib/digsig:
pkcs_1_v1_5_decode_emsa cleanup").
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 13 Sep 2012 01:05:22 +0000 (09:05 +0800)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"It's been a while... so there's a little more here than normal.
Mostly updates from Will for the breakpoint stuff, and plugging a few
holes in the user access functions which crept in when domain support
was disabled for ARMv7 CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7529/1: delay: set loops_per_jiffy when moving to timer-based loop
ARM: 7528/1: uaccess: annotate [__]{get,put}_user functions with might_fault()
ARM: 7527/1: uaccess: explicitly check __user pointer when !CPU_USE_DOMAINS
ARM: 7526/1: traps: send SIGILL if get_user fails on undef handling path
ARM: 7521/1: Fix semihosting Kconfig text
ARM: 7513/1: Make sure dtc is built before running it
ARM: 7512/1: Fix XIP build due to PHYS_OFFSET definition moving
ARM: 7499/1: mm: Fix vmalloc overlap check for !HIGHMEM
ARM: 7503/1: mm: only flush both pmd entries for classic MMU
ARM: 7502/1: contextidr: avoid using bfi instruction during notifier
ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores
ARM: 7497/1: hw_breakpoint: allow single-byte watchpoints on all addresses
ARM: 7496/1: hw_breakpoint: don't rely on dfsr to show watchpoint access type
ARM: Fix ioremap() of address zero
Linus Torvalds [Thu, 13 Sep 2012 01:04:13 +0000 (09:04 +0800)]
Merge tag 'nfs-for-3.6-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Final (hopefully) fix for the range checking code in NFSv4 getacl.
This should fix the Oopses being seen when the acl size is close to
PAGE_SIZE.
- Fix a regression with the legacy binary mount code
- Fix a regression in the readdir cookieverf initialisation
- Fix an RPC over UDP regression
- Ensure that we report all errors in the NFSv4 open code
- Ensure that fsync() reports all relevant synchronisation errors.
* tag 'nfs-for-3.6-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: fsync() must exit with an error if page writeback failed
SUNRPC: Fix a UDP transport regression
NFS: return error from decode_getfh in decode open
NFSv4: Fix buffer overflow checking in __nfs4_get_acl_uncached
NFSv4: Fix range checking in __nfs4_get_acl_uncached and __nfs4_proc_set_acl
NFS: Fix a problem with the legacy binary mount code
NFS: Fix the initialisation of the readdir 'cookieverf' array
Greg Kroah-Hartman [Wed, 12 Sep 2012 18:12:31 +0000 (11:12 -0700)]
Merge branch 'chipidea-stable' into usb-linus
Chipidea patches for 3.6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik [Wed, 12 Sep 2012 11:58:04 +0000 (14:58 +0300)]
usb: chipidea: udc: don't stall endpoint if request list is empty in isr_tr_complete_low
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde [Wed, 12 Sep 2012 11:58:03 +0000 (14:58 +0300)]
usb: chipidea: cleanup dma_pool if udc_start() fails
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde [Wed, 12 Sep 2012 11:58:02 +0000 (14:58 +0300)]
usb: chipidea: udc: fix error path in udc_start()
This patch fixes the error path of udc_start(). Now NULL is used to
unset the peripheral with otg_set_peripheral().
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik [Wed, 12 Sep 2012 11:58:01 +0000 (14:58 +0300)]
usb: chipidea: udc: add pullup fuction, needed by the uvc gadget
Add function to physicaly enable or disable of pullup connection on the USB-D+
line. The uvc gaget will fail, if this function is not implemented.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik [Wed, 12 Sep 2012 11:58:00 +0000 (14:58 +0300)]
usb: chipidea: udc: fix setup of endpoint maxpacket size
This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.
Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joe Perches [Wed, 12 Sep 2012 02:04:53 +0000 (02:04 +0000)]
netfilter: log: Fix log-level processing
auto75914331@hushmail.com reports that iptables does not correctly
output the KERN_<level>.
$IPTABLES -A RULE_0_in -j LOG --log-level notice --log-prefix "DENY in: "
result with linux 3.6-rc5
Sep 12 06:37:29 xxxxx kernel: <5>DENY in: IN=eth0 OUT= MAC=.......
result with linux 3.5.3 and older:
Sep 9 10:43:01 xxxxx kernel: DENY in: IN=eth0 OUT= MAC......
commit
04d2c8c83d0
("printk: convert the format for KERN_<LEVEL> to a 2 byte pattern")
updated the syslog header style but did not update netfilter uses.
Do so.
Use KERN_SOH and string concatenation instead of "%c" KERN_SOH_ASCII
as suggested by Eric Dumazet.
Signed-off-by: Joe Perches <joe@perches.com>
cc: auto75914331@hushmail.com
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Matteo Frigo [Wed, 12 Sep 2012 14:12:06 +0000 (10:12 -0400)]
ALSA: ice1724: Use linear scale for AK4396 volume control.
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
Signed-off-by: Matteo Frigo <athena@fftw.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eric Dumazet [Tue, 11 Sep 2012 13:11:12 +0000 (13:11 +0000)]
net-sched: sch_cbq: avoid infinite loop
Its possible to setup a bad cbq configuration leading to
an infinite loop in cbq_classify()
DEV_OUT=eth0
ICMP="match ip protocol 1 0xff"
U32="protocol ip u32"
DST="match ip dst"
tc qdisc add dev $DEV_OUT root handle 1: cbq avpkt 1000 \
bandwidth 100mbit
tc class add dev $DEV_OUT parent 1: classid 1:1 cbq \
rate 512kbit allot 1500 prio 5 bounded isolated
tc filter add dev $DEV_OUT parent 1: prio 3 $U32 \
$ICMP $DST 192.168.3.234 flowid 1:
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Tested-by: Denys Fedoryschenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 11 Sep 2012 23:16:54 +0000 (07:16 +0800)]
Merge branch 'for-3.6-fixes' of git://git./linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"It's later than I'd like but well the timing just didn't work out this
time.
There are three bug fixes. One from before 3.6-rc1 and two from the
new CPU hotplug code. Kudos to Lai for discovering all of them and
providing fixes.
* Atomicity bug when clearing a flag and setting another. The two
operation should have been atomic but wasn't. This bug has existed
for a long time but is unlikely to have actually happened. Fix is
safe. Marked for -stable.
* If CPU hotplug cycles happen back-to-back before workers finish the
previous cycle, the states could get out of sync and it could get
stuck. Fixed by waiting for workers to complete before finishing
hotplug cycle.
* While CPU hotplug is in progress, idle workers could be depleted
which can then lead to deadlock. I think both happening together
is highly unlikely but still better to fix it and the fix isn't too
scary.
There's another workqueue related regression which reported a few days
ago:
https://bugzilla.kernel.org/show_bug.cgi?id=47301
It's a bit of head scratcher but there is a semi-reliable reproduce
case, so I'm hoping to resolve it soonish."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix possible idle worker depletion across CPU hotplug
workqueue: restore POOL_MANAGING_WORKERS
workqueue: fix possible deadlock in idle worker rebinding
workqueue: move WORKER_REBIND clearing in rebind_workers() to the end of the function
workqueue: UNBOUND -> REBIND morphing in rebind_workers() should be atomic
Linus Torvalds [Tue, 11 Sep 2012 23:14:17 +0000 (07:14 +0800)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the authenc self-test crash as well as a missing export of
a symbol used by a module."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authenc - Fix crash with zero-length assoc data
crypto/caam: Export gen_split_key symbol for other modules
Linus Torvalds [Tue, 11 Sep 2012 23:12:53 +0000 (07:12 +0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lliubbo/blackfin
Pull blackfin updates from Bob Liu:
"One kbuild and a smp build fix."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
kbuild: add symbol prefix arg to kallsyms
blackfin: smp: adapt to generic smp helpers
Trond Myklebust [Tue, 11 Sep 2012 19:38:32 +0000 (15:38 -0400)]
NFS: fsync() must exit with an error if page writeback failed
We need to ensure that if the call to filemap_write_and_wait_range()
fails, then we report that error back to the application.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Bjørn Mork [Tue, 11 Sep 2012 07:40:31 +0000 (09:40 +0200)]
USB: option: replace ZTE K5006-Z entry with vendor class rule
Fix the ZTE K5006-Z entry so that it actually matches anything
commit
f1b5c997 USB: option: add ZTE K5006-Z
added a device specific entry assuming that the device would use
class/subclass/proto == ff/ff/ff like other ZTE devices. It
turns out that ZTE has started using vendor specific subclass
and protocol codes:
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1018 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF821Vxxxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=86 Prot=10 Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=05 Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=00 Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
We do not have any information on how ZTE intend to use these
codes, but let us assume for now that the 3 sets matching
serial functions in the K5006-Z always will identify a serial
function in a ZTE device.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Catalin Iacob [Sun, 9 Sep 2012 21:41:11 +0000 (21:41 +0000)]
ALSA: hda_intel: add position_fix quirk for Asus K53E
Commit
c20c5a841cbe47f5b7812b57bd25397497e5fbc0 changed some chipsets to
default to POS_FIX_COMBO so they now use POS_FIX_LPIB instead of
POS_FIX_POSBUF. Since then I've been getting artifacts on playback, including
repeated sounds on my Asus laptop.
My hardware is Cougar Point which the commit log of
c20c5a841cbe47f5b7812b57bd25397497e5fbc0 mentions as tested so POS_FIX_COMBO
probably works in general but apparently it doesn't on Asus K53E therefore the
need for the quirk.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter [Tue, 11 Sep 2012 11:12:43 +0000 (14:12 +0300)]
ALSA: compress_core: fix open flags test in snd_compr_open()
O_RDONLY is zero so the original test (f->f_flags & O_RDONLY) is always
false and it will never do compress capture. The test for O_WRONLY is
also slightly off. The original test would consider "->flags =
(O_WRONLY | O_RDWR)" as write only instead of rejecting it as invalid.
I've also removed the pr_err() because that could flood dmesg.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fabio Estevam [Mon, 20 Aug 2012 12:39:22 +0000 (09:39 -0300)]
ARM: clk-imx35: Fix SSI clock registration
SSI block has two types of clock:
ipg: bus clock, the clock needed for accessing registers.
per: peripheral clock, the clock needed for generating the bit rate.
Currently SSI driver only supports slave mode and only need to handle
the ipg clock, because the peripheral clock comes from the master codec.
Only register the ipg clock and do not register the peripheral clock for ssi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Fabio Estevam [Sun, 19 Aug 2012 17:05:59 +0000 (14:05 -0300)]
ARM: clk-imx25: Fix SSI clock registration
SSI block has two types of clock:
ipg: bus clock, the clock needed for accessing registers.
per: peripheral clock, the clock needed for generating the bit rate.
Currently SSI driver only supports slave mode and only need to handle
the ipg clock, because the peripheral clock comes from the master codec.
Only register the ipg clock and do not register the peripheral clock for ssi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Pierre Sauter [Mon, 10 Sep 2012 07:02:59 +0000 (07:02 +0000)]
net: qmi_wwan: fix Gobi device probing for un2430
HP un2430 is a Gobi 3000 device. It was mistakenly treated as Gobi 1000
in patch
b9f90eb2740203ff2592efe640409ad48335d1c2.
I own this device and qmi_wwan works again with this fix.
Signed-off-by: Pierre Sauter <pierre.sauter@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 11 Sep 2012 04:05:45 +0000 (12:05 +0800)]
crypto: authenc - Fix crash with zero-length assoc data
The authenc code doesn't deal with zero-length associated data
correctly and ends up constructing a zero-length sg entry which
causes a crash when it's fed into the crypto system.
This patch fixes this by avoiding the code-path that triggers
the SG construction if we have no associated data.
This isn't the most optimal fix as it means that we'll end up
using the fallback code-path even when we could still execute
the digest function. However, this isn't a big deal as nobody
but the test path would supply zero-length associated data.
Reported-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Romain Francoise <romain@orebokech.com>
James Hogan [Thu, 6 Sep 2012 21:11:25 +0000 (22:11 +0100)]
kbuild: add symbol prefix arg to kallsyms
Commit
1f2bfbd00e466ff3489b2ca5cc75b1cccd14c123 ("kbuild: link of
vmlinux moved to a script") introduced in v3.5-rc1 broke kallsyms on
architectures which have symbol prefixes.
The --symbol-prefix argument used to be added to the KALLSYMS command
line from the architecture Makefile, however this isn't picked up by the
new scripts/link-vmlinux.sh. This resulted in symbols like
kallsyms_addresses being added which weren't correctly overriding the
weak symbols such as _kallsyms_addresses. These could then trigger
BUG_ONs in kallsyms code.
This is fixed by removing the KALLSYMS addition from the architecture
Makefile, and using CONFIG_SYMBOL_PREFIX in the link-vmlinux.sh script
to determine whether to add the --symbol-prefix argument.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Linus Torvalds [Tue, 11 Sep 2012 01:31:26 +0000 (09:31 +0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"I had actually prepared this fix set before I left for KS + Plumbers,
so it's been incubating much longer than it should have. I'll be
picking up my three week backlog this week, so more fixes will then be
forthcoming
This set consist of three minor and one fairly major (the device not
ready causing offlining problem which is a serious regression
introduced by the media change update) fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix 'Device not ready' issue on mpt2sas
[SCSI] scsi_lib: fix scsi_io_completion's SG_IO error propagation
[SCSI] megaraid_sas: Move poll_aen_lock initializer
[SCSI] mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value
Linus Torvalds [Tue, 11 Sep 2012 01:30:08 +0000 (09:30 +0800)]
Merge tag 'kvm-3.6-2' of git://git./virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"A trio of KVM fixes: incorrect lookup of guest cpuid, an uninitialized
variable fix, and error path cleanup fix."
* tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: fix error paths for failed gfn_to_page() calls
KVM: x86: Check INVPCID feature bit in EBX of leaf 7
KVM: PIC: fix use of uninitialised variable.
Linus Torvalds [Tue, 11 Sep 2012 01:29:17 +0000 (09:29 +0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse
Pull FUSE fixes from Miklos Szeredi:
"This contains bugfixes for FUSE and CUSE and a compile warning fix."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix retrieve length
fuse: mark variables uninitialized
cuse: kill connection on initialization error
cuse: fix fuse_conn_kill()
Rob Clark [Fri, 7 Sep 2012 17:59:45 +0000 (12:59 -0500)]
drm/omap: add more new timings fields
Without these, DVI is broken.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rob Clark [Wed, 5 Sep 2012 21:48:53 +0000 (16:48 -0500)]
drm/omap: update for interlaced
'struct omap_video_timings' was updated w/ a 'bool interlaced'. Without
a matching update in omap_connector, this field could have undefined
values from the stack, which isn't quite ideal.
Update the fxns to convert omapdss<->drm timings structs, and zero-init
'struct omap_video_timings' when it is declared on stack to avoid issues
like this in the future.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavankumar Kondeti [Fri, 7 Sep 2012 05:53:28 +0000 (11:23 +0530)]
EHCI: Update qTD next pointer in QH overlay region during unlink
There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.
Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.
qTD1 --> qTD2 --> Dummy
To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed. The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt. If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error. Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Mon, 10 Sep 2012 19:22:11 +0000 (21:22 +0200)]
staging: r8712u: fix bug in r8712_recv_indicatepkt()
64bit arches have a buggy r8712u driver, let's fix it.
skb->tail must be set properly or network stack behavior is undefined.
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=847525
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=45071
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Jones <davej@redhat.com>
Cc: stable <stable@vger.kernel.org> [2.6.37+]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Mon, 10 Sep 2012 20:17:34 +0000 (22:17 +0200)]
USB: cdc-wdm: fix wdm_find_device* return value
A logic error made the wdm_find_device* functions
return a bogus pointer into static data instead of
the intended NULL no matching device was found.
Cc: stable <stable@vger.kernel.org> # v3.4+
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 10 Sep 2012 21:52:49 +0000 (05:52 +0800)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French.
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix endianness conversion
CIFS: Fix error handling in cifs_push_mandatory_locks
Linus Torvalds [Mon, 10 Sep 2012 21:51:35 +0000 (05:51 +0800)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull UDF and ext3 fixes from Jan Kara:
"One UDF data corruption fix and one ext3 fix where we didn't write
everything to disk on fsync in one corner case."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fix data corruption for files in ICB
ext3: Fix fdatasync() for files with only i_size changes
Randy Dunlap [Mon, 10 Sep 2012 16:13:07 +0000 (09:13 -0700)]
net: fix net/core/sock.c build error
Fix net/core/sock.c build error when CONFIG_INET is not enabled:
net/built-in.o: In function `sock_edemux':
(.text+0xd396): undefined reference to `inet_twsk_put'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 10 Sep 2012 12:06:58 +0000 (14:06 +0200)]
ixp4xx_hss: fix build failure due to missing linux/module.h inclusion
Commit
36a1211970193ce215de50ed1e4e1272bc814df1 (netprio_cgroup.h:
dont include module.h from other includes) made the following build
error on ixp4xx_hss pop up:
CC [M] drivers/net/wan/ixp4xx_hss.o
drivers/net/wan/ixp4xx_hss.c:1412:20: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1413:25: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1414:21: error: expected ';', ',' or ')'
before string constant
drivers/net/wan/ixp4xx_hss.c:1415:19: error: expected ';', ',' or ')'
before string constant
make[8]: *** [drivers/net/wan/ixp4xx_hss.o] Error 1
This was previously hidden because ixp4xx_hss includes linux/hdlc.h which
includes linux/netdevice.h which includes linux/netprio_cgroup.h which
used to include linux/module.h. The real issue was actually present since
the initial commit that added this driver since it uses macros from
linux/module.h without including this file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Sun, 9 Sep 2012 18:38:27 +0000 (18:38 +0000)]
caif: move the dereference below the NULL test
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennart Sorensen [Fri, 7 Sep 2012 12:14:02 +0000 (12:14 +0000)]
sierra_net: Endianess bug fix.
I discovered I couldn't get sierra_net to work on a powerpc. Turns out
the firmware attribute check assumes the system is little endian and
hence fails because the attributes is a 16 bit value.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Mon, 10 Sep 2012 10:01:05 +0000 (12:01 +0200)]
USB: ftdi_sio: do not claim CDC ACM function
The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application. This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction. The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.
Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00. I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.
Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 10 Sep 2012 17:13:59 +0000 (01:13 +0800)]
Merge branch 'i2c-for-linus' of git://git./linux/kernel/git/jdelvare/staging
Pull i2c subsystem fixes from Jean Delvare.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-core: Fix for lockdep validator
i2c-designware: Fix build error if CONFIG_I2C_DESIGNWARE_PLATFORM=y && CONFIG_I2C_DESIGNWARE_PCI=y
i2c-i801: Add Device IDs for Intel Lynx Point-LP PCH
Lai Jiangshan [Mon, 10 Sep 2012 17:03:44 +0000 (10:03 -0700)]
workqueue: fix possible idle worker depletion across CPU hotplug
To simplify both normal and CPU hotplug paths, worker management is
prevented while CPU hoplug is in progress. This is achieved by CPU
hotplug holding the same exclusion mechanism used by workers to ensure
there's only one manager per pool.
If someone else seems to be performing the manager role, workers
proceed to execute work items. CPU hotplug using the same mechanism
can lead to idle worker depletion because all workers could proceed to
execute work items while CPU hotplug is in progress and CPU hotplug
itself wouldn't actually perform the worker management duty - it
doesn't guarantee that there's an idle worker left when it releases
management.
This idle worker depletion, under extreme circumstances, can break
forward-progress guarantee and thus lead to deadlock.
This patch fixes the bug by using separate mechanisms for manager
exclusion among workers and hotplug exclusion. For manager exclusion,
POOL_MANAGING_WORKERS which was restored by the previous patch is
used. pool->manager_mutex is now only used for exclusion between the
elected manager and CPU hotplug. The elected manager won't proceed
without holding pool->manager_mutex.
This ensures that the worker which won the manager position can't skip
managing while CPU hotplug is in progress. It will block on
manager_mutex and perform management after CPU hotplug is complete.
Note that hotplug may happen while waiting for manager_mutex. A
manager isn't either on idle or busy list and thus the hoplug code
can't unbind/rebind it. Make the manager handle its own un/rebinding.
tj: Updated comment and description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Linus Torvalds [Mon, 10 Sep 2012 17:05:19 +0000 (01:05 +0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Just noticed I hadn't send these out, nothing majorly urgent, I know
AMD guys have some regression fixes coming soon.
This contains:
2 nouveau fixes so it loads on the retina MBP systems properly,
2 vmwgfx fixes to load the driver earlier, and allow distros config it
1 error->debug fix in ast
and Keith was playing with 32-on-64 and decided we may as well stick
the compat ioctl in all the drivers. It fixes udl for him."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: add MODULE_DEVICE_TABLE so vmwgfx loads at boot
drm/vmwgfx: allow a kconfig option to choose if fbcon is enabled
drm: use drm_compat_ioctl for 32-bit apps
drm/ast: drop debug level on error printk
drm/nv50-/gpio: initialise to vbios defaults during init
drm/nvd0/disp: hopefully fix selection of 6/8bpc mode on DP outputs
Lai Jiangshan [Mon, 10 Sep 2012 17:03:33 +0000 (10:03 -0700)]
workqueue: restore POOL_MANAGING_WORKERS
This patch restores POOL_MANAGING_WORKERS which was replaced by
pool->manager_mutex by
6037315269 "workqueue: use mutex for global_cwq
manager exclusion".
There's a subtle idle worker depletion bug across CPU hotplug events
and we need to distinguish an actual manager and CPU hotplug
preventing management. POOL_MANAGING_WORKERS will be used for the
former and manager_mutex the later.
This patch just lays POOL_MANAGING_WORKERS on top of the existing
manager_mutex and doesn't introduce any synchronization changes. The
next patch will update it.
Note that this patch fixes a non-critical anomaly where
too_many_workers() may return %true spuriously while CPU hotplug is in
progress. While the issue could schedule idle timer spuriously, it
didn't trigger any actual misbehavior.
tj: Rewrote patch description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Xiao Guangrong [Fri, 7 Sep 2012 06:14:20 +0000 (14:14 +0800)]
KVM: fix error paths for failed gfn_to_page() calls
This bug was triggered:
[ 4220.198458] BUG: unable to handle kernel paging request at
fffffffffffffffe
[ 4220.203907] IP: [<
ffffffff81104d85>] put_page+0xf/0x34
......
[ 4220.237326] Call Trace:
[ 4220.237361] [<
ffffffffa03830d0>] kvm_arch_destroy_vm+0xf9/0x101 [kvm]
[ 4220.237382] [<
ffffffffa036fe53>] kvm_put_kvm+0xcc/0x127 [kvm]
[ 4220.237401] [<
ffffffffa03702bc>] kvm_vcpu_release+0x18/0x1c [kvm]
[ 4220.237407] [<
ffffffff81145425>] __fput+0x111/0x1ed
[ 4220.237411] [<
ffffffff8114550f>] ____fput+0xe/0x10
[ 4220.237418] [<
ffffffff81063511>] task_work_run+0x5d/0x88
[ 4220.237424] [<
ffffffff8104c3f7>] do_exit+0x2bf/0x7ca
The test case:
printf(fmt, ##args); \
exit(-1);} while (0)
static int create_vm(void)
{
int sys_fd, vm_fd;
sys_fd = open("/dev/kvm", O_RDWR);
if (sys_fd < 0)
die("open /dev/kvm fail.\n");
vm_fd = ioctl(sys_fd, KVM_CREATE_VM, 0);
if (vm_fd < 0)
die("KVM_CREATE_VM fail.\n");
return vm_fd;
}
static int create_vcpu(int vm_fd)
{
int vcpu_fd;
vcpu_fd = ioctl(vm_fd, KVM_CREATE_VCPU, 0);
if (vcpu_fd < 0)
die("KVM_CREATE_VCPU ioctl.\n");
printf("Create vcpu.\n");
return vcpu_fd;
}
static void *vcpu_thread(void *arg)
{
int vm_fd = (int)(long)arg;
create_vcpu(vm_fd);
return NULL;
}
int main(int argc, char *argv[])
{
pthread_t thread;
int vm_fd;
(void)argc;
(void)argv;
vm_fd = create_vm();
pthread_create(&thread, NULL, vcpu_thread, (void *)(long)vm_fd);
printf("Exit.\n");
return 0;
}
It caused by release kvm->arch.ept_identity_map_addr which is the
error page.
The parent thread can send KILL signal to the vcpu thread when it was
exiting which stops faulting pages and potentially allocating memory.
So gfn_to_pfn/gfn_to_page may fail at this time
Fixed by checking the page before it is used
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Takashi Iwai [Mon, 10 Sep 2012 07:39:31 +0000 (09:39 +0200)]
ALSA: hda - Fix Oops at codec reset/reconfig
snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec. However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.
This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.
Reported-by: Daniel J Blueman <daniel@quora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jean Delvare [Mon, 10 Sep 2012 08:14:02 +0000 (10:14 +0200)]
i2c-core: Fix for lockdep validator
If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().
Based on an earlier fix from Michael Lawnick.
Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Axel Lin [Mon, 10 Sep 2012 08:14:02 +0000 (10:14 +0200)]
i2c-designware: Fix build error if CONFIG_I2C_DESIGNWARE_PLATFORM=y && CONFIG_I2C_DESIGNWARE_PCI=y
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.
Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.
This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:
LD drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]
James Ralston [Mon, 10 Sep 2012 08:14:02 +0000 (10:14 +0200)]
i2c-i801: Add Device IDs for Intel Lynx Point-LP PCH
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jozsef Kadlecsik [Fri, 31 Aug 2012 09:55:54 +0000 (09:55 +0000)]
netfilter: Validate the sequence number of dataless ACK packets as well
We spare nothing by not validating the sequence number of dataless
ACK packets and enabling it makes harder off-path attacks.
See: "Reflection scan: an Off-Path Attack on TCP" by Jan Wrobel,
http://arxiv.org/abs/1201.2074
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jozsef Kadlecsik [Fri, 31 Aug 2012 09:55:53 +0000 (09:55 +0000)]
netfilter: Mark SYN/ACK packets as invalid from original direction
Clients should not send such packets. By accepting them, we open
up a hole by wich ephemeral ports can be discovered in an off-path
attack.
See: "Reflection scan: an Off-Path Attack on TCP" by Jan Wrobel,
http://arxiv.org/abs/1201.2074
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Will Deacon [Fri, 7 Sep 2012 17:24:53 +0000 (18:24 +0100)]
ARM: 7529/1: delay: set loops_per_jiffy when moving to timer-based loop
The delay functions may be called by some platforms between switching to
the timer-based delay loop but before calibration. In this case, the
initial loops_per_jiffy may not be suitable for the timer (although a
compromise may be achievable) and delay times may be considered too
inaccurate.
This patch updates loops_per_jiffy when switching to the timer-based
delay loop so that delays are consistent prior to calibration.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Fri, 7 Sep 2012 17:24:10 +0000 (18:24 +0100)]
ARM: 7528/1: uaccess: annotate [__]{get,put}_user functions with might_fault()
The user access functions may generate a fault, resulting in invocation
of a handler that may sleep.
This patch annotates the accessors with might_fault() so that we print a
warning if they are invoked from atomic context and help lockdep keep
track of mmap_sem.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 7 Sep 2012 17:22:28 +0000 (18:22 +0100)]
ARM: 7527/1: uaccess: explicitly check __user pointer when !CPU_USE_DOMAINS
The {get,put}_user macros don't perform range checking on the provided
__user address when !CPU_HAS_DOMAINS.
This patch reworks the out-of-line assembly accessors to check the user
address against a specified limit, returning -EFAULT if is is out of
range.
[will: changed get_user register allocation to match put_user]
[rmk: fixed building on older ARM architectures]
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ren, Yongjie [Fri, 7 Sep 2012 07:36:59 +0000 (07:36 +0000)]
KVM: x86: Check INVPCID feature bit in EBX of leaf 7
Checks and operations on the INVPCID feature bit should use EBX
of CPUID leaf 7 instead of ECX.
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Yongjie Ren <yongjien.ren@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linus Torvalds [Sat, 8 Sep 2012 23:43:45 +0000 (16:43 -0700)]
Linux 3.6-rc5
Linus Torvalds [Sat, 8 Sep 2012 23:22:43 +0000 (16:22 -0700)]
Merge branch 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit
e9da6e9905e6 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
Linus Torvalds [Sat, 8 Sep 2012 23:20:59 +0000 (16:20 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: i8042 - add Gigabyte T1005 series netbooks to noloop table
Input: imx_keypad - reset the hardware before enabling
Input: edt-ft5x06 - fix build error when compiling wthout CONFIG_DEBUG_FS
Chema Gonzalez [Fri, 7 Sep 2012 13:40:50 +0000 (13:40 +0000)]
net: small bug on rxhash calculation
In the current rxhash calculation function, while the
sorting of the ports/addrs is coherent (you get the
same rxhash for packets sharing the same 4-tuple, in
both directions), ports and addrs are sorted
independently. This implies packets from a connection
between the same addresses but crossed ports hash to
the same rxhash.
For example, traffic between A=S:l and B=L:s is hashed
(in both directions) from {L, S, {s, l}}. The same
rxhash is obtained for packets between C=S:s and D=L:l.
This patch ensures that you either swap both addrs and ports,
or you swap none. Traffic between A and B, and traffic
between C and D, get their rxhash from different sources
({L, S, {l, s}} for A<->B, and {L, S, {s, l}} for C<->D)
The patch is co-written with Eric Dumazet <edumazet@google.com>
Signed-off-by: Chema Gonzalez <chema@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Fri, 7 Sep 2012 22:03:21 +0000 (15:03 -0700)]
Merge tag 'omap-fixes-for-v3.6-rc4' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Fixes for timer, sram, memory corruption, and one board file that affect
booting on various omaps. Then some PM related fixes for reset, sleep
and wakeup.
* tag 'omap-fixes-for-v3.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: Fix array size for irq_target_cpu
ARM: OMAP4: hwmod data: temporarily comment out data for the sl2if IP block
ARM: OMAP: hwmod code: Disable module when hwmod enable fails
ARM: OMAP3: hwmod data: fix iva2 reset info
ARM: OMAP3xxx: clockdomain: fix software supervised wakeup/sleep
ARM: OMAP2+: am33xx: Fix the timer fck clock naming convention
ARM: OMAP: Config fix for omap3-touchbook board
ARM: OMAP: sram: skip the first 16K on OMAP3 HS
ARM: OMAP: sram: fix OMAP4 errata handling
ARM: OMAP: timer: obey the !CONFIG_OMAP_32K_TIMER
Will Deacon [Fri, 7 Sep 2012 17:21:44 +0000 (18:21 +0100)]
ARM: 7526/1: traps: send SIGILL if get_user fails on undef handling path
get_user may fail to load from the provided __user address due to an
unhandled fault generated by the access.
In the case of the undefined instruction trap, this results in failure
to load the faulting instruction, in which case we should send SIGILL to
the task rather than continue with potentially uninitialised data.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stephen Boyd [Thu, 6 Sep 2012 20:24:32 +0000 (21:24 +0100)]
ARM: 7521/1: Fix semihosting Kconfig text
It seems we were missing some text in the title for the
semihosting DEBUG_LL option. Add in the "/O" and fix up some
minor typos in the help text.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Brown [Tue, 4 Sep 2012 20:36:37 +0000 (21:36 +0100)]
ARM: 7513/1: Make sure dtc is built before running it
'make dtbs' in a clean tree will try running the dtc before actually
building it. Make these rules depend upon the scripts to build it.
Cc: <stable@vger.kernel.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stephen Boyd [Tue, 4 Sep 2012 19:04:35 +0000 (20:04 +0100)]
ARM: 7512/1: Fix XIP build due to PHYS_OFFSET definition moving
During the p2v changes, the PHYS_OFFSET #define moved into a
!__ASSEMBLY__ section. This causes a XIP build to fail with
arch/arm/kernel/head.o: In function 'stext':
arch/arm/kernel/head.S:146: undefined reference to 'PHYS_OFFSET'
Momentarily leave the #ifndef __ASSEMBLY__ section so we can
define PHYS_OFFSET for all compilation units.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Fri, 7 Sep 2012 19:29:38 +0000 (12:29 -0700)]
Merge branch 'upstream-fixes' of git://git./linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
performance improvement (not processing debug data if noone is
interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
work even with generic driver in a crippled mode, by Andres Freund."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
HID: Only dump input if someone is listening
HID: add NOGET quirk for Eaton Ellipse MAX UPS
John W. Linville [Fri, 7 Sep 2012 17:33:27 +0000 (13:33 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless into for-davem
John W. Linville says:
====================
Please pull these fixes intended for 3.6. There are more commits
here than I would like -- I got a bit behind while I was stalking
Steven Rostedt in San Diego last week... I'll slow it down after this!
There are a couple of pulls here. One is from Johannes:
"Please pull (according to the below information) to get a few fixes.
* a fix to properly disconnect in the driver when authentication or
association fails
* a fix to prevent invalid information about mesh paths being reported
to userspace
* a memory leak fix in an nl80211 error path"
The other comes via Gustavo:
"A few updates for the 3.6 kernel. There are two btusb patches to add
more supported devices through the new USB_VENDOR_AND_INTEFACE_INFO()
macro and another one that add a new device id for a Sony Vaio laptop,
one fix for a user-after-free and, finally, two patches from Vinicius
to fix a issue in SMP pairing."
Along with those...
Arend van Spriel provides a fix for a use-after-free bug in brcmfmac.
Daniel Drake avoids a hang by not trying to touch the libertas hardware
duing suspend if it is already powered-down.
Felix Fietkau provides a batch of ath9k fixes that adress some
potential problems with power settings, as well as a fix to avoid a
potential interrupt storm.
Gertjan van Wingerde provides a register-width fix for rt2x00, and
a rt2x00 fix to prevent incorrectly detecting the rfkill status.
He also provides a device ID patch.
Hante Meuleman gives us three brcmfmac fixes, one that properly
initializes a command structure, one that fixes a race condition that
could lose usb requests, and one that removes some log spam.
Marc Kleine-Budde offers an rt2x00 fix for a voltage setting on some
specific devices.
Mohammed Shafi Shajakhan sent an ath9k fix to avoid a crash related to
using timers that aren't allocated when 2 wire bluetooth coexistence
hardware is in use.
Sergei Poselenov changes rt2800usb to do some validity checking for
received packets, avoiding crashes on an ARM Soc.
Stone Piao gives us an mwifiex fix for an incorrectly set skb length
value for a command buffer.
All of these are localized to their specific drivers, and relatively
small. The power-related patches from Felix are bigger than I would
like, but I merged them in consideration of their isolation to ath9k
and the sensitive nature of power settings in wireless devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Thu, 6 Sep 2012 00:47:05 +0000 (00:47 +0000)]
|PATCH] seeq: Add missing spinlock init
It doesn't seem this spinlock was properly initialized.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 5 Sep 2012 23:34:44 +0000 (23:34 +0000)]
udp: increment UDP_MIB_INERRORS if copy failed
In UDP recvmsg(), we miss an increase of UDP_MIB_INERRORS if the copy
of skb to userspace failed for whatever reason.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugenia Emantayev [Wed, 5 Sep 2012 22:50:52 +0000 (22:50 +0000)]
net/mlx4_core: Return the error value in case of command initialization failure
If mlx4_cmd_init() failed, the init_one function returned
success, although no resources were opened.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Yehezkel [Wed, 5 Sep 2012 22:50:51 +0000 (22:50 +0000)]
net/mlx4_core: Fixing error flow in case of QUERY_FW failure
The order of operations was wrong on the teardown flow.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aviad Yehezkel [Wed, 5 Sep 2012 22:50:50 +0000 (22:50 +0000)]
net/mlx4_core: Looking for promiscuous entries on the correct port
The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Wed, 5 Sep 2012 22:50:49 +0000 (22:50 +0000)]
net/mlx4_core: Add security check / enforcement for flow steering rules set for VMs
Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hadar Hen Zion [Wed, 5 Sep 2012 22:50:48 +0000 (22:50 +0000)]
net/mlx4_core: Put Firmware flow steering structures in common header files
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This page took 0.05293 seconds and 5 git commands to generate.