Johannes Berg [Fri, 7 Oct 2011 12:01:25 +0000 (14:01 +0200)]
mac80211: move fragment flag to info flag as dont-fragment
The purpose of this is two-fold:
1) by moving it out of tx_data.flags, we can in
another patch move the radiotap parsing so it
no longer is in the hotpath
2) if a device implements fragmentation but can
optionally skip it, the radiotap request for
not doing fragmentation may be honoured
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 7 Oct 2011 12:01:24 +0000 (14:01 +0200)]
mac80211: remove tx_data ethertype
It's set, but never used, so kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 7 Oct 2011 12:01:23 +0000 (14:01 +0200)]
mac80211: optimise monitor xmit
Since the only way the interface can be a monitor
interface in ieee80211_xmit() is because the frame
came from ieee80211_monitor_start_xmit() we can
move all the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 7 Oct 2011 09:53:41 +0000 (11:53 +0200)]
mac80211: Update injection documentation
Add documentation about NOACK tx flag usage.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 7 Oct 2011 00:28:15 +0000 (02:28 +0200)]
ath9k: fix retry counting / BAR handling during queue flush
When tx is suspended temporarily and the queue is flushed, do not increase
the retry count or attempt to send out BAR frames. Instead simply retry
the affected subframes normally after the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 7 Oct 2011 00:28:14 +0000 (02:28 +0200)]
ath9k: improve PS filter clearing and retry counting for A-MPDU
Do not increment the retry counter if packets to a sleeping station
were not sent because of tx failure, instead of only checking the filter
flag.
Clear the PS filter only after an A-MPDU was reported as filtered,
otherwise the hardware might do some unnecessary extra retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 7 Oct 2011 00:28:13 +0000 (02:28 +0200)]
ath9k: keep track of what's triggering hardware resets
Export how many times each of the reset triggers has fired through debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 7 Oct 2011 00:28:12 +0000 (02:28 +0200)]
ath9k: indicate which queues are blocked when stopping tx fails
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 6 Oct 2011 21:54:22 +0000 (14:54 -0700)]
mac80211: Fix regression that allowed mpaths between non-peers.
Mesh paths should only exist over established peer links.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Wed, 5 Oct 2011 21:58:24 +0000 (14:58 -0700)]
mwifiex: fix smatch errors
drivers/net/wireless/mwifiex/main.c +828 mwifiex_remove_card(52)
error: potential null derefence 'priv'.
drivers/net/wireless/mwifiex/main.c +828 mwifiex_remove_card(52)
error: we previously assumed 'priv' could be null (see line 820)
drivers/net/wireless/mwifiex/txrx.c +90 mwifiex_process_tx(24)
error: potential null derefence 'local_tx_pd'.
drivers/net/wireless/mwifiex/sta_ioctl.c +766
mwifiex_rate_ioctl_set_rate_value(30)
error: buffer overflow 'rate' 14 <= 14
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 5 Oct 2011 05:48:20 +0000 (08:48 +0300)]
ath9k: remove some bogus error handling code
If "axq_qnum >= ARRAY_SIZE(sc->tx.txq)", then the call to
ath9k_hw_releasetxqueue() would read beyond the end of the ah->txq[]
array and possibly corrupt memory. Fortunately,
ath9k_hw_setuptxqueue() doesn't return high values of "axq_qnum" and
this code can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 5 Oct 2011 05:46:37 +0000 (08:46 +0300)]
ath5k: remove some unneeded error handling code
th5k_hw_setup_tx_queue() returns a valid offset into the ah->ah_txq[]
array. The ah->ah_txq[] and the ah->txqs[] array are the same size.
Both have AR5K_NUM_TX_QUEUES elements. So this error handling code
will never trigger.
Also it's wrong. The call to ath5k_hw_release_tx_queue() with a qnum
of AR5K_NUM_TX_QUEUES or more will just trigger a WARN_ON() and
return. Or if it missed the WARN_ON(), it would just corrupt some
memory and return.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 4 Oct 2011 16:27:10 +0000 (18:27 +0200)]
mac80211: fix offchannel TX cookie matching
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Cc: stable@kernel.org [2.6.38+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Tue, 4 Oct 2011 14:10:19 +0000 (07:10 -0700)]
iwlagn: separate init calib and rt calib
My previous patch for init calib cfg disable a set of calibration for both
init and runtime which cause performance issue, Fix it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 4 Oct 2011 13:07:33 +0000 (15:07 +0200)]
mac80211: pass no-CCK flag through to HW scan
This is needed so that offloaded scan can do the
right thing. Without this patch, the no_cck flag
contains random values from the kernel heap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 11 Oct 2011 19:56:29 +0000 (15:56 -0400)]
Merge branch 'for-linville' of git://github.com/lucacoelho/wl12xx
Arend van Spriel [Wed, 5 Oct 2011 11:19:03 +0000 (13:19 +0200)]
net: wireless: add brcm80211 drivers
Add the brcm80211 tree to drivers/net/wireless, and disable the version that's
in drivers/staging. This version includes the sources currently in staging,
plus any changes that have been sent out for review.
Sources in staging will be deleted in a followup patch.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 11 Oct 2011 19:33:10 +0000 (15:33 -0400)]
ath6kl: fixup merge damage in ath6kl_mgmt_tx
CC [M] drivers/net/wireless/ath/ath6kl/cfg80211.o
drivers/net/wireless/ath/ath6kl/cfg80211.c:1838:2: warning: initialization from incompatible pointer type
Caused by commit
e9f935e3e8dc0bddd0df6d148165d95925422502...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Wed, 5 Oct 2011 09:55:38 +0000 (11:55 +0200)]
wl12xx: disable AP-mode-specific quirks
The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.
WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Shahar Levi [Thu, 8 Sep 2011 10:01:33 +0000 (13:01 +0300)]
wl12xx: Add support for HW channel switch
The wl12xx FW supports HW channel switch. If we don't use it,
sometimes the firmware gets confused when recalibrating to the new
channel, causing RX problems. This commit adds HW channel switch
support by implementing the channell_switch op.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
[added one comment, remove the tx_flush and rephrased the commit message]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 27 Sep 2011 13:22:35 +0000 (16:22 +0300)]
wl12xx: set max_sched_scan_ie_len correctly
The wiphy max_sched_scan_ie_len attribute was not set correctly and
remained as 0, so when IEs were being passed in a scheduled scan, we
were returning -EINVAL.
Fix this by setting the attribute properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 3 Oct 2011 10:06:36 +0000 (12:06 +0200)]
wl12xx: configure rate policy for p2p operations
p2p packets should go out only with OFDM rates.
Configure a new rate policy that will (later) be used
during p2p_find (when the p2p_cli / p2p_go interfaces
are in use, we won't have to use this policy, as
the configured rates should already be OFDM-only).
Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect
the current value from the fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
John W. Linville [Tue, 4 Oct 2011 18:06:47 +0000 (14:06 -0400)]
Merge branch 'master' of git://github.com/padovan/bluetooth-next
Mohammed Shafi Shajakhan [Fri, 30 Sep 2011 06:01:28 +0000 (11:31 +0530)]
ath9k_hw: set pci_express capability true for AR9480
the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Fri, 30 Sep 2011 06:01:27 +0000 (11:31 +0530)]
ath9k_hw: Fix number of GPIO pins for AR9287/9300
this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Mon, 3 Oct 2011 10:33:02 +0000 (11:33 +0100)]
libertas: detect TX lockups and reset hardware
Recent patches added support for resetting the SD8686 hardware when
commands time out, which seems to happen quite frequently soon after
resuming the system from a Wake-on-WLAN-triggered resume.
At http://dev.laptop.org/ticket/10969 we see the same thing happen
with transmits. In this case, the hardware will fail to respond to
a frame passed for transmission, and libertas (correctly) will block
all further commands and transmissions as the hardware can only
deal with one thing at a time. This results in a lockup while the
system waits indefinitely for the dead card to respond.
Hook up a TX lockup timer to detect this and reset the hardware.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Sun, 2 Oct 2011 08:15:52 +0000 (10:15 +0200)]
mac80211: pass vif param to conf_tx() callback
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Fri, 30 Sep 2011 18:40:20 +0000 (11:40 -0700)]
iwlagn: rename iwlagn module iwlwifi and alias to iwlagn.
Rename the iwlagn module as iwlwifi in preparation for future
changes. Add an alias to iwlagn for backward compatibility.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Fri, 30 Sep 2011 06:47:28 +0000 (12:17 +0530)]
ath9k_hw: extend GPIO pin select mask for rfkill
this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as
we use GPIO pin 11 as rfkill for AR9480 and also remove few unused
macros
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: "Hu, Russell" <rhu@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 30 Sep 2011 03:43:41 +0000 (20:43 -0700)]
mwifiex: handle an error path correctly
In failure case locks are not allocated in mwifiex_register().
So mwifiex_free_lock_list() routine call becomes redundant.
Also we don't need to check return type for mwifiex_init_lock_list()
routine. It never fails.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 30 Sep 2011 03:43:40 +0000 (20:43 -0700)]
mwifiex: correct AMSDU aggregation check
The commit "mwifiex: remove list traversal.."(
fcf2176c87..)
wrongly modifies AMSDU aggregation check. Due to this even though
packet size for iperf traffic is already large, we unnecessarily
try to aggregate them which adds some delay. If Tx iperf is started
on UUT for 30 seconds, UUT keeps sending Tx packets for few more
seconds.
That commit is reverted to fix the problem.
Also, MIN_NUM_AMSDU check is moved inside the loop to optimize the
loop.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 29 Sep 2011 17:42:19 +0000 (10:42 -0700)]
ath9k_htc: add AVM FRITZ!WLAN 11N v2 support
This was reported and tested by Martin Walter over at AVM GmbH Berlin.
This also applies to 3.0.1 so sendint to stable.
Cc: s.kirste@avm.de
Cc: d.friedel@avm.de
Cc: Martin Walter <m.walter@avm.de>
Cc: Peter Grabienski <pgrabien@qca.qualcomm.com>
Cc: stable@kernel.org
Tested-by: Martin Walter <m.walter@avm.de>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Thu, 29 Sep 2011 15:04:04 +0000 (20:34 +0530)]
mac80211: Send nullfunc frames at lower rate during connection monitor
Recently mac80211 was changed to use nullfunc instead of probe
request for connection monitoring for tx ack status reporting
hardwares. Sometimes in congested network, STA got disconnected
quickly after the association. It was observered that the rate
control was not adopted to environment due to minimal transmission.
As the nullfunc are used for monitoring purpose, these frames should
not be sacrificed for rate control updation. So it is better to send
the monitoring null func frames at minimum rate that could help to
retain the connection.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sangwook Lee [Thu, 29 Sep 2011 11:57:17 +0000 (12:57 +0100)]
net:rfkill: add a gpio setup function into GPIO rfkill
Add a gpio setup function which gives a chance to set up
platform specific configuration such as pin multiplexing,
input/output direction at the runtime or booting time.
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 29 Sep 2011 11:42:25 +0000 (13:42 +0200)]
mac80211: Allow noack flag overwrite for injected frames
Allow injected unicast frames to be sent without having to wait
for an ACK.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 3 Oct 2011 18:59:35 +0000 (14:59 -0400)]
Merge branch 'for-linville' of git://github.com/kvalo/ath6kl
Kalle Valo [Mon, 3 Oct 2011 10:44:40 +0000 (13:44 +0300)]
ath6kl: include vmalloc.h in debug.c
Fixes compilation errors when compiling for ARM:
ath6kl/debug.c:312: error: implicit declaration of function 'vmalloc'
ath6kl/debug.c:312: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:342: error: implicit declaration of function 'vfree'
ath6kl/debug.c:696: warning: assignment makes pointer from integer without a cast
ath6kl/debug.c:871: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Sat, 1 Oct 2011 06:43:09 +0000 (09:43 +0300)]
ath6kl: fix size_t related warnings
My earlier debug log additions added these warnings when compiling 64 bit
kernels:
ath6kl/init.c:962: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:975: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:988: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1009: warning: format '%d' expects type 'int',
but argument 3 has type 'size_t'
ath6kl/init.c:1192: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1236: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
ath6kl/init.c:1267: warning: format '%d' expects type 'int',
but argument 4 has type 'size_t'
Reported-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:41 +0000 (16:04 +0200)]
mac80211: dont assign seqno to or aggregate QoS Null frames
802.11 says:
"Sequence numbers for QoS (+)Null frames may be
set to any value."
However, if we use the normal counters then peers
will get confused with aggregation since there'll
be holes in the sequence number sequence.
To avoid that, neither assign a sequence number
to QoS null frames nor put them on aggregation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:40 +0000 (16:04 +0200)]
mac80211: document client powersave
With the addition of uAPSD and driver buffering
the powersave handling has gotten quite complex.
Add a section to the documentation to explain it
for anyone wanting to implement it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:39 +0000 (16:04 +0200)]
mac80211: allow out-of-band EOSP notification
iwlwifi has a separate EOSP notification from
the device, and to make use of that properly
it needs to be passed to mac80211. To be able
to mix with tx_status_irqsafe and rx_irqsafe
it also needs to be an "_irqsafe" version in
the sense that it goes through the tasklet,
the actual flag clearing would be IRQ-safe
but doing it directly would cause reordering
issues.
This is needed in the case of a P2P GO going
into an absence period without transmitting
any frames that should be driver-released as
in this case there's no other way to inform
mac80211 that the service period ended. Note
that for drivers that don't use the _irqsafe
functions another version of this function
will be required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:38 +0000 (16:04 +0200)]
mac80211: explicitly notify drivers of frame release
iwlwifi needs to know the number of frames that are
going to be sent to a station while it is asleep so
it can properly handle the uCode blocking of that
station.
Before uAPSD, we got by by telling the device that
a single frame was going to be released whenever we
encountered IEEE80211_TX_CTL_POLL_RESPONSE. With
uAPSD, however, that is no longer possible since
there could be more than a single frame.
To support this model, add a new callback to notify
drivers when frames are going to be released.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:37 +0000 (16:04 +0200)]
mac80211: add missing station flags to debugfs
My work and some previous work didn't add
all the flags, add them now and while at it
simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:36 +0000 (16:04 +0200)]
mac80211: optimise station flags
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:35 +0000 (16:04 +0200)]
mac80211: reply only once to each PS-poll
If a PS-poll frame is retried (but was received)
there is no way to detect that since it has no
sequence number. As a consequence, the standard
asks us to not react to PS-poll frames until the
response to one made it out (was ACKed or lost).
Implement this by using the WLAN_STA_SP flags to
also indicate a PS-Poll "service period" and the
IEEE80211_TX_STATUS_EOSP flag for the response
packet to indicate the end of the "SP" as usual.
We could use separate flags, but that will most
likely completely confuse drivers, and while the
standard doesn't exclude simultaneously polling
using uAPSD and PS-Poll, doing that seems quite
problematic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:34 +0000 (16:04 +0200)]
mac80211: send (QoS) Null if no buffered frames
For PS-poll, there's a possible race between
us expiring a frame and the station polling
for it -- send it a null frame in that case.
For uAPSD, the standard says that we have to
send a frame in each SP, so send null if we
don't have any other frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:33 +0000 (16:04 +0200)]
mac80211: implement uAPSD
Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.
Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:32 +0000 (16:04 +0200)]
mac80211: allow releasing driver-buffered frames
If there are frames for a station buffered in
the driver, mac80211 announces those in the TIM
IE but there's no way to release them. Add new
API to release such frames and use it when the
station polls for a frame.
Since the API will soon also be used for uAPSD
it is easily extensible.
Note that before this change drivers announcing
driver-buffered frames in the TIM bit actually
will respond to a PS-Poll with a potentially
lower priority frame (if there are any frames
buffered in mac80211), after this patch a driver
that hasn't been changed will no longer respond
at all. This only affects ath9k, which will need
to be fixed to implement the new API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:31 +0000 (16:04 +0200)]
mac80211: clear more-data bit on filtered frames
It doesn't seem likely, but maybe possible, that the
more-data bit needs to be recomputed due to changes
in the queued frames. Clear it for filtered frames
to ensure that we never send it incorrectly. It'll
be set again as necessary when we retransmit this
frame.
The more likely case is maybe where the station woke
up after the filtered frame in which case more-data
should be clear when the frame is transmitted to the
station since it is now awake.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:30 +0000 (16:04 +0200)]
mac80211: remove return value from add_pending_skbs
Now that we no longer use the return value, we no
longer need to maintain it either, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:29 +0000 (16:04 +0200)]
mac80211: split PS buffers into ACs
For uAPSD support we'll need to have per-AC PS
buffers. As this is a major undertaking, split
the buffers before really adding support for
uAPSD. This already makes some reference to the
uapsd_queues variable, but for now that will
never be non-zero.
Since book-keeping is complicated, also change
the logic for keeping a maximum of frames only
and allow 64 frames per AC (up from 128 for a
station).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:28 +0000 (16:04 +0200)]
mac80211: also expire filtered frames
mac80211 will expire normal PS-buffered frames, but
if the device rejected some frames for a sleeping
station, these won't be on the ps_tx_buf queue but
on the tx_filtered queue instead; this is done to
avoid reordering.
However, mac80211 will not expire frames from the
filtered queue, let's fix that.
Also add a more comments to what all this expiry is
doing and how it works.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:27 +0000 (16:04 +0200)]
mac80211: unify TIM bit handling
Currently, the TIM bit for a given station is set
and cleared all over the place. Since the logic to
set/clear it will become much more complex when we
add uAPSD support, as a first step let's collect
the entire logic in one place. This requires a few
small adjustments to other places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 29 Sep 2011 14:04:26 +0000 (16:04 +0200)]
mac80211: let drivers inform it about per TID buffered frames
For uAPSD implementation, it is necessary to know on
which ACs frames are buffered. mac80211 obviously
knows about the frames it has buffered itself, but
with aggregation many drivers buffer frames. Thus,
mac80211 needs to be informed about this.
For now, since we don't have APSD in any form, this
will unconditionally set the TIM bit for the station
but later with uAPSD only some ACs might cause the
TIM bit to be set.
ath9k is the only driver using this API and I only
modify it in the most basic way, it won't be able
to implement uAPSD with this yet. But it can't do
that anyway since there's no way to selectively
release frames to the peer yet.
Since drivers will buffer frames per TID, let them
inform mac80211 on a per TID basis, mac80211 will
then sort out the AC mapping itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Wed, 28 Sep 2011 11:12:54 +0000 (14:12 +0300)]
mac80211: data path modification for TDLS peers
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Wed, 28 Sep 2011 11:12:53 +0000 (14:12 +0300)]
nl80211/mac80211: allow adding TDLS peers as stations
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Wed, 28 Sep 2011 11:12:52 +0000 (14:12 +0300)]
mac80211: handle TDLS high-level commands and frames
Register and implement the TDLS cfg80211 callback functions.
Internally prepare and send TDLS management frames. We incorporate
local STA capabilities and supported rates with extra IEs given by
usermode. The resulting packet is either encapsulated in a data frame,
or assembled as an action frame. It is transmitted either directly or
through the AP, as mandated by the TDLS specification.
Declare support for the TDLS external setup wiphy capability. This
tells usermode to handle link setup and discovery on its own, and use the
kernel driver for sending TDLS mgmt packets.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Wed, 28 Sep 2011 11:12:51 +0000 (14:12 +0300)]
mac80211: standardize adding supported rates IEs
Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Wed, 28 Sep 2011 11:12:50 +0000 (14:12 +0300)]
nl80211: support sending TDLS commands/frames
Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.
Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Wed, 28 Sep 2011 22:54:04 +0000 (17:54 -0500)]
iwlagn: iwl-agn-rs: remove unnecessary null check for sta and lq_sta
both sta and lq_sta are guaranteed to be not null in the
calling function so we don't need to check them here.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 28 Sep 2011 11:26:10 +0000 (16:56 +0530)]
ath9k/ath9k_htc: Fix PS wrappers for RF kill
ath9k_hw_gpio_get reads the GPIO in/out registers to get the status of
GPIO pins, so use PS wrappers
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 27 Sep 2011 18:56:12 +0000 (20:56 +0200)]
cfg80211/mac80211: apply station uAPSD parameters selectively
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 27 Sep 2011 05:48:21 +0000 (00:48 -0500)]
rtlwifi: Remove unused _usb_nbytes_read_write and _usb_writeN_sync
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 27 Sep 2011 05:48:20 +0000 (00:48 -0500)]
rtlwifi: Remove unused routine _usb_readN_sync
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Tue, 27 Sep 2011 03:37:26 +0000 (20:37 -0700)]
mwifiex: add cfg80211 handlers add/del_virtual_intf
Making adding and deleting virtual interfaces dynamic. Adding
handlers for creating and deleting virtual interface with
given name and dev respectively.
Also, creating default interface of type station on insmod of
the driver.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 27 Sep 2011 03:37:25 +0000 (20:37 -0700)]
mwifiex: fix Tx data rate display issue
"iw dev mlan0 link" shows wrong data rate, because data rate is
not sent properly to cfg80211 stack. Also stack is not updated
with mcs and Tx data flags information.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 27 Sep 2011 03:37:24 +0000 (20:37 -0700)]
mwifiex: remove unreachable code
In disconnected state "iw dev mlan0 link" command will return
from cfg80211 stack itself. We also have an error check in
mwifiex_cfg80211_get_station() routine. Therefore the code
under "if (!priv->media_connected)" condition in
mwifiex_rate_ioctl_get_rate_value() routine becomes unreachable.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Tue, 27 Sep 2011 03:37:23 +0000 (20:37 -0700)]
mwifiex: remove unnecessary mwifiex_dump_station_info() call
An extra call to mwifiex_dump_station_info() routine in get_station
callback function is redundant
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 26 Sep 2011 16:46:56 +0000 (22:16 +0530)]
ath9k: Remove redundant my beacon check at ath_rx_ps_beacon
Make use of the rx status's is_mybeacon in order to avoid
redundant memcmp.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 26 Sep 2011 16:18:39 +0000 (21:48 +0530)]
ath9k: Remove unnecessary AMPDU check at tx status
Fill the ampdu_[ack]_len for both aggregation and normal frames.
So that we could avoid unnecesary conditional at tx status.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Sat, 24 Sep 2011 16:48:26 +0000 (18:48 +0200)]
mac80211: max_tp_rate2 management of minstrel_ht
I noticed a possible issue in the max_tp_rate2 management of
minstrel_ht. In particular, if we look up just among max_tp_rate2 of
each group it will be possible that the selected rate will not be the
mcs with second maximum throughput. I wrote this simple patch.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andy Shevchenko [Wed, 28 Sep 2011 09:30:59 +0000 (12:30 +0300)]
wireless: at76c50x: use native hex_pack_byte() method
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oliver Neukum [Wed, 21 Sep 2011 09:41:45 +0000 (11:41 +0200)]
btusb: add device entry for Broadcom SoftSailing
From
0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
This device declares itself to be vendor specific
It therefore needs to be added to the device table
to make btusb bind.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Mon, 26 Sep 2011 23:48:35 +0000 (20:48 -0300)]
Bluetooth: hci_le_adv_report_evt code refactoring
There is no reason to treat the first advertising entry differently
from the potential other ones. Besides, the current implementation
can easily leads to typos.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Waldemar Rymarkiewicz [Fri, 23 Sep 2011 08:01:30 +0000 (10:01 +0200)]
Bluetooth: Fix possible NULL pointer dereference
Checking conn->pending_sec_level if there is no connection leads to potential
null pointer dereference. Don't process pin_code_request_event at all if no
connection exists.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Stephen Rothwell [Wed, 28 Sep 2011 08:32:34 +0000 (18:32 +1000)]
wireless/ath6kl: use of module_param requires the inclusion of moduleparam.h
Otheriwse the module.h split up fails like this:
drivers/net/wireless/ath/ath6kl/init.c:27:26: error: expected ')' before 'uint'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Tue, 27 Sep 2011 11:31:21 +0000 (14:31 +0300)]
ath6kl: improve wmi debug messages
Add a new debug level ATH6KL_DBG_WMI_DUMP and other minor
improvements to the wmi debug messages.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Tue, 27 Sep 2011 11:31:11 +0000 (14:31 +0300)]
ath6kl: add debug logs for booting
Just to make it easier to find out why boot fails.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Tue, 27 Sep 2011 11:30:58 +0000 (14:30 +0300)]
ath6kl: add sdio debug messages
Add extensive debug messages to sdio.c. Makes it easier to debug
various problems.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Tue, 27 Sep 2011 11:30:45 +0000 (14:30 +0300)]
ath6kl: add prefix parameter to ath6kl_dbg_dump()
Makes it easier to recognise longs dumps.
Obligatory screenshot using "rx" prefix:
ath6kl: ath6kl_rx
rx
00000000: 10 10 00 00 00 00 08 30 00 00 00 00 00 00 f9 0b .......0........
rx
00000010: 2c 44 08 30 00 00 f9 0b 0c a4 02 00 00 00 73 d2 ,D.0..........s.
rx
00000020: 94 00 f9 0b 04 8c 01 00 02 00 07 02 02 00 f9 0b ................
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kalle Valo [Tue, 27 Sep 2011 20:33:28 +0000 (23:33 +0300)]
ath6kl: silence "invalid rate" warning
For some reason firmware is sending invalid rates when we try to
query current bitrate from ath6kl_get_station() and a warning is issued:
[ 3810.415720] ath6kl: invalid rate:
1935633515
[ 3811.105493] ath6kl: invalid rate:
1935633515
[ 3811.556063] ath6kl: invalid rate:
1935633515
As the warning happens way too often, convert the warning to a debug
message once we have a proper fix. But to make it easy to follow
how often the problem appears, add a debugfs to print
various statistics about workarounds and make this issue the first WAR.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville [Wed, 28 Sep 2011 14:28:09 +0000 (10:28 -0400)]
Merge branch 'master' of git://git.infradead.org/users/linville/wireless
Conflicts:
drivers/net/wireless/iwlwifi/iwl-scan.c
net/wireless/nl80211.c
Szymon Janc [Thu, 28 Jul 2011 14:24:33 +0000 (16:24 +0200)]
Bluetooth: Mark not declared l2cap_core functions as static
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Anderson Lizardo [Wed, 27 Jul 2011 21:40:09 +0000 (18:40 -0300)]
Bluetooth: use recommended LE connection parameters
The new connection parameters now match the recommended values for
Proximity and Health Thermometer profiles. The previous values were
ramdomly chosen, and are either too low or too high for most cases.
New values:
Scan Interval: 60 ms
Scan Window: 30 ms
Minimum Connection Interval: 50 ms
Maximum Connection Interval: 70 ms
Supervision Timeout: 420 ms
See "Table 5.2: Recommended Scan Interval and Scan Window Values" and
"Table 5.3: Recommended Connection Interval Values" for both profiles
for details. Note that the "fast connection" parameters were chosen,
because we do not support yet dynamically changing these parameters from
initiator side.
Additionally, the Proximity profile recommends (section "4.4 Alert on
Link Loss"):
"It is recommended that the Link Supervision Timeout (LSTO) is set to 6x
the connection interval."
Minimum_CE_Length and Maximum_CE_Length were also changed from 0x0001 to
0x0000 because they are informational and optional, and old value was
not reflecting reality.
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Fri, 22 Jul 2011 21:54:00 +0000 (14:54 -0700)]
Bluetooth: Perform L2CAP SDU reassembly without copying data
Use sk_buff fragment capabilities to link together incoming skbs
instead of allocating a new skb for reassembly and copying.
The new reassembly code works equally well for ERTM and streaming
mode, so there is now one reassembly function instead of two.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Fri, 22 Jul 2011 21:53:59 +0000 (14:53 -0700)]
Bluetooth: Handle fragmented skbs in bt_sock_stream_recvmsg()
ERTM reassembly will be more efficient when skbs are linked together
rather than copying every incoming data byte. The existing stream recv
function assumes skbs are linear, so it needs to know how to handle
fragments before reassembly is changed.
bt_sock_recvmsg() already handles fragmented skbs.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Fri, 22 Jul 2011 21:53:58 +0000 (14:53 -0700)]
Bluetooth: Linearize skbs for use in BNEP, CMTP, HIDP, and RFCOMM
Fragmented skbs are only encountered when receiving ERTM or streaming
mode L2CAP data. BNEP, CMTP, HIDP, and RFCOMM generally use basic
mode, but they need to handle fragments without crashing.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Peter Hurley [Thu, 14 Jul 2011 12:48:32 +0000 (08:48 -0400)]
Bluetooth: Allow ACL packets over USB in HCI_RAW mode
Removed tests which prevent transmission of ACL packets
when the device is in HCI_RAW mode. These tests verified that
there are ACL or LE links currently tracked by the HCI
connection manager. However, a HCI_RAW mode device does not
use the connection manager. In these circumstances, the connection
counts will be zero, and thus, transmitted ACL packets dropped.
The acl_num test is actually a vestige of a previous bulk URB
scheme that is no longer used by this driver (bulk URBs were not
started until at least one ACL connection was created). This was
incompatible with some endpoint implementations and was dropped -
see commit
43c2e57f94.
The utility of these tests is marginal - currently, the hci tx
scheduler cannot send an ACL or LE packet for an untracked connection
(except if the device is in HCI_RAW mode).
Lastly, no other transport layer driver enforces these same tests.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Arik Nemtsov [Mon, 26 Sep 2011 06:36:42 +0000 (09:36 +0300)]
mac80211: treat the WME sta flag as a bit
Correct flag usage - use it as a bit index instead of a bit value.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Mon, 26 Sep 2011 06:30:40 +0000 (09:30 +0300)]
wl3501_cs: min_t() cast truncates high bits
wrqu->encoding.length comes from the network administrator. It's
size u16. We want to limit "tocopy" to the smallest value of either
"len_keys", "wrqu->encoding.length" or 100. But because .length
gets cast from u16 to u8 we might use a random, smaller value than
the was desired. It's probably not very serious, but we may as well
fix it.
Btw, this is from code auditing and not from testing. I don't know
if this affects anyone in real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Sun, 25 Sep 2011 17:06:54 +0000 (20:06 +0300)]
mac80211: save tx params per sdata
save and configure tx param per sdata, rather than
per hardware.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Sun, 25 Sep 2011 17:06:53 +0000 (20:06 +0300)]
cfg80211/mac80211: add netdev param to set_txq_params()
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sun, 25 Sep 2011 09:23:31 +0000 (14:53 +0530)]
mac80211: Send the management frame at requested rate
Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sun, 25 Sep 2011 09:23:30 +0000 (14:53 +0530)]
nl80211/cfg80211: Add support to disable CCK rate for management frame
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Fri, 23 Sep 2011 06:14:35 +0000 (09:14 +0300)]
NFC: use after free on error
We returned a freed variable on some error paths when the intent was
to return a NULL. Part of the reason this was missed was that the
code was confusing because it had too many gotos so I removed them
and simplified the flow a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 22 Sep 2011 22:15:00 +0000 (15:15 -0700)]
iwlagn: fix scan complete processing
When we cancel a scan, the completion runs
only from the workqueue. This can cause the
remain-on-channel scan to fail when another
one was just canceled, because we're still
aborting it.
To fix this, run the completion inline with
the lock still held before returning from
iwl_scan_cancel_timeout().
Also, to avoid the scan complete work from
completing a new scan prematurely, add a
new STATUS_SCAN_COMPLETE bit.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 22 Sep 2011 22:14:59 +0000 (15:14 -0700)]
iwlagn: move iwl_process_scan_complete up
To make the next patch easier to read, move
the function up, it'll be needed earlier in
this file in the next patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 22 Sep 2011 22:14:58 +0000 (15:14 -0700)]
iwlagn: refactor scan complete
We'll need to be able to run scan complete
inline, not from the workqueue, so refactor
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 22 Sep 2011 22:14:57 +0000 (15:14 -0700)]
iwlagn: make iwl_scan_cancel_timeout void
The return value of iwl_scan_cancel_timeout()
isn't used anywhere, so let's just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 22 Sep 2011 22:14:56 +0000 (15:14 -0700)]
iwlagn: remove Kelvin support
Only 5150 series devices report their temperature
in Kelvin, and for those we already convert it to
Celsius when storing into priv->temperature, so
there's no way priv->temperature will ever be in
Kelvin. Remove support for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This page took 0.046002 seconds and 5 git commands to generate.