Andy Lutomirski [Wed, 15 Jul 2015 17:29:37 +0000 (10:29 -0700)]
x86/nmi/64: Reorder nested NMI checks
Check the repeat_nmi .. end_repeat_nmi special case first. The
next patch will rework the RSP check and, as a side effect, the
RSP check will no longer detect repeat_nmi .. end_repeat_nmi, so
we'll need this ordering of the checks.
Note: this is more subtle than it appears. The check for
repeat_nmi .. end_repeat_nmi jumps straight out of the NMI code
instead of adjusting the "iret" frame to force a repeat. This
is necessary, because the code between repeat_nmi and
end_repeat_nmi sets "NMI executing" and then writes to the
"iret" frame itself. If a nested NMI comes in and modifies the
"iret" frame while repeat_nmi is also modifying it, we'll end up
with garbage. The old code got this right, as does the new
code, but the new code is a bit more explicit.
If we were to move the check right after the "NMI executing"
check, then we'd get it wrong and have random crashes.
( Because the "NMI executing" check would jump to the code that would
modify the "iret" frame without checking if the interrupted NMI was
currently modifying it. )
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andy Lutomirski [Wed, 15 Jul 2015 17:29:36 +0000 (10:29 -0700)]
x86/nmi/64: Improve nested NMI comments
I found the nested NMI documentation to be difficult to follow.
Improve the comments.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andy Lutomirski [Wed, 15 Jul 2015 17:29:35 +0000 (10:29 -0700)]
x86/nmi/64: Switch stacks on userspace NMI entry
Returning to userspace is tricky: IRET can fail, and ESPFIX can
rearrange the stack prior to IRET.
The NMI nesting fixup relies on a precise stack layout and
atomic IRET. Rather than trying to teach the NMI nesting fixup
to handle ESPFIX and failed IRET, punt: run NMIs that came from
user mode on the normal kernel stack.
This will make some nested NMIs visible to C code, but the C
code is okay with that.
As a side effect, this should speed up perf: it eliminates an
RDMSR when NMIs come from user mode.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andy Lutomirski [Wed, 15 Jul 2015 17:29:34 +0000 (10:29 -0700)]
x86/nmi/64: Remove asm code that saves CR2
Now that do_nmi saves CR2, we don't need to save it in asm.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andy Lutomirski [Wed, 15 Jul 2015 17:29:33 +0000 (10:29 -0700)]
x86/nmi: Enable nested do_nmi() handling for 64-bit kernels
32-bit kernels handle nested NMIs in C. Enable the exact same
handling on 64-bit kernels as well. This isn't currently
necessary, but it will become necessary once the asm code starts
allowing limited nesting.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Fri, 17 Jul 2015 04:10:53 +0000 (21:10 -0700)]
Merge tag 'pm+acpi-4.2-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two bugs in the cpufreq core (including one recent
regression), fix a 4.0 PCI regression related to the ACPI resources
management and quieten an RCU-related lockdep complaint about a
tracepoint in the suspend-to-idle code.
Specifics:
- Fix a recently introduced issue in the cpufreq policy object
reinitialization that leads to CPU offline/online breakage (Viresh
Kumar)
- Make it possible to access frequency tables of offline CPUs which
is needed by thermal management code among other things (Viresh
Kumar)
- Fix an ACPI resource management regression introduced during the
4.0 cycle that may cause incorrect resource validation results to
appear in 32-bit x86 kernels due to silent truncation of 64-bit
values to 32-bit (Jiang Liu)
- Fix up an RCU-related lockdep complaint about suspicious RCU usage
in idle caused by using a suspend tracepoint in the core suspend-
to-idle code (Rafael J Wysocki)"
* tag 'pm+acpi-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
Linus Torvalds [Fri, 17 Jul 2015 03:57:25 +0000 (20:57 -0700)]
Merge tag 'platform-drivers-x86-v4.2-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix SMBIOS call handling and hwswitch state coherency in the
dell-laptop driver. Cleanups for intel_*_ipc drivers. Details:
dell-laptop:
- Do not cache hwswitch state
- Check return value of each SMBIOS call
- Clear buffer before each SMBIOS call
intel_scu_ipc:
- Move local memory initialization out of a mutex
intel_pmc_ipc:
- Update kerneldoc formatting
- Fix compiler casting warnings"
* tag 'platform-drivers-x86-v4.2-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_scu_ipc: move local memory initialization out of a mutex
intel_pmc_ipc: Update kerneldoc formatting
dell-laptop: Do not cache hwswitch state
dell-laptop: Check return value of each SMBIOS call
dell-laptop: Clear buffer before each SMBIOS call
intel_pmc_ipc: Fix compiler casting warnings
Linus Torvalds [Fri, 17 Jul 2015 03:49:09 +0000 (20:49 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/gerg/m68knommu
Pull m68knommu/coldfire fixes from Greg Ungerer:
"Contains build fixes and updates for the ColdFire defconfigs.
Specifically there is a couple of fixes that address problems building
allnoconfig. Also fix for enabling PCI bus on the M54xx family of
ColdFire"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: enable PCI support for m5475evb defconfig
m68k: fix io functions for ColdFire/MMU/PCI case
m68knommu: update defconfig for ColdFire m5475evb
m68knommu: update defconfig for ColdFire m5407c3
m68knommu: update defconfig for ColdFire m5307c3
m68knommu: update defconfig for ColdFire m5275evb
m68knommu: update defconfig for ColdFire m5272c3
m68knommu: update defconfig for ColdFire m5249evb
m68knommu: update defconfig for m5208evb
m68knommu: make ColdFire SoC selection a choice
m68knommu: improve the clock configuration defaults
m68knommu: force setting of CONFIG_CLOCK_FREQ for ColdFire
Linus Torvalds [Thu, 16 Jul 2015 23:38:08 +0000 (16:38 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes from the last few weeks that should go into the
current series. This contains:
- Various fixes for the per-blkcg policy data, fixing regressions
since 4.1. From Arianna and Tejun
- Code cleanup for bcache closure macros from me. Really just
flushing this out, it's been sitting in another branch for months
- FIELD_SIZEOF cleanup from Maninder Singh
- bio integrity oops fix from Mike
- Timeout regression fix for blk-mq from Ming Lei"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: set default timeout as 30 seconds
NVMe: Reread partitions on metadata formats
bcache: don't embed 'return' statements in closure macros
blkcg: fix blkcg_policy_data allocation bug
blkcg: implement all_blkcgs list
blkcg: blkcg_css_alloc() should grab blkcg_pol_mutex while iterating blkcg_policy[]
blkcg: allow blkcg_pol_mutex to be grabbed from cgroup [file] methods
block/blk-cgroup.c: free per-blkcg data when freeing the blkcg
block: use FIELD_SIZEOF to calculate size of a field
bio integrity: do not assume bio_integrity_pool exists if bioset exists
Linus Torvalds [Thu, 16 Jul 2015 23:28:28 +0000 (16:28 -0700)]
Merge tag 'jfs-4.2' of git://github.com/kleikamp/linux-shaggy
Pull jfs fixes from David Kleikamp:
"A couple trivial fixes and an error path fix"
* tag 'jfs-4.2' of git://github.com/kleikamp/linux-shaggy:
jfs: clean up jfs_rename and fix out of order unlock
jfs: fix indentation on if statement
jfs: removed a prohibited space after opening parenthesis
Rafael J. Wysocki [Thu, 16 Jul 2015 21:47:19 +0000 (23:47 +0200)]
Merge branches 'pm-cpuidle', 'pm-cpufreq' and 'acpi-resources'
* pm-cpuidle:
suspend-to-idle: Prevent RCU from complaining about tick_freeze()
* pm-cpufreq:
cpufreq: Allow freq_table to be obtained for offline CPUs
cpufreq: Initialize the governor again while restoring policy
* acpi-resources:
ACPI / PCI: Fix regressions caused by resource_size_t overflow with 32-bit kernel
Ming Lei [Thu, 16 Jul 2015 11:53:22 +0000 (19:53 +0800)]
blk-mq: set default timeout as 30 seconds
It is reasonable to set default timeout of request as 30 seconds instead of
30000 ticks, which may be 300 seconds if HZ is 100, for example, some arm64
based systems may choose 100 HZ.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Fixes: c76cbbcf4044 ("blk-mq: put blk_queue_rq_timeout together in blk_mq_init_queue()"
Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Thu, 16 Jul 2015 01:38:24 +0000 (18:38 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull TPM bugfixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm, tpm_crb: fail when TPM2 ACPI table contents look corrupted
tpm: Fix initialization of the cdev
Linus Torvalds [Thu, 16 Jul 2015 00:03:03 +0000 (17:03 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Mainly fix-ups for the various 4.2 items"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (24 commits)
IB/core: Destroy ocrdma_dev_id IDR on module exit
IB/core: Destroy multcast_idr on module exit
IB/mlx4: Optimize do_slave_init
IB/mlx4: Fix memory leak in do_slave_init
IB/mlx4: Optimize freeing of items on error unwind
IB/mlx4: Fix use of flow-counters for process_mad
IB/ipath: Convert use of __constant_<foo> to <foo>
IB/ipoib: Set MTU to max allowed by mode when mode changes
IB/ipoib: Scatter-Gather support in connected mode
IB/ucm: Fix bitmap wrap when devnum > IB_UCM_MAX_DEVICES
IB/ipoib: Prevent lockdep warning in __ipoib_ib_dev_flush
IB/ucma: Fix lockdep warning in ucma_lock_files
rds: rds_ib_device.refcount overflow
RDMA/nes: Fix for incorrect recording of the MAC address
RDMA/nes: Fix for resolving the neigh
RDMA/core: Fixes for port mapper client registration
IB/IPoIB: Fix bad error flow in ipoib_add_port()
IB/mlx4: Do not attemp to report HCA clock offset on VFs
IB/cm: Do not queue work to a device that's going away
IB/srp: Avoid using uninitialized variable
...
Keith Busch [Tue, 14 Jul 2015 17:57:48 +0000 (11:57 -0600)]
NVMe: Reread partitions on metadata formats
This patch has the driver automatically reread partitions if a namespace
has a separate metadata format. Previously revalidating a disk was
sufficient to get the correct capacity set on such formatted drives,
but partitions that may exist would not have been surfaced.
Reported-by: Paul Grabinar <paul.grabinar@ranbarg.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Paul Grabinar <paul.grabinar@ranbarg.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Wed, 15 Jul 2015 20:35:23 +0000 (13:35 -0700)]
Merge tag 'locks-v4.2-1' of git://git.samba.org/jlayton/linux
Pull file locking updates from Jeff Layton:
"I had thought that I was going to get away without a pull request this
cycle. There was a NFSv4 file locking problem that cropped up that I
tried to fix in the NFSv4 code alone, but that fix has turned out to
be problematic. These patches fix this in the correct way.
Note that this touches some NFSv4 code as well. Ordinarily I'd wait
for Trond to ACK this, but he's on holiday right now and the bug is
rather nasty. So I suggest we merge this and if he raises issues with
it we can sort it out when he gets back"
Acked-by: Bruce Fields <bfields@fieldses.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
[ +1 to this series fixing a 100% reproducible slab corruption +
general protection fault in my nfs-root test environment. - Dan ]
Acked-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
* tag 'locks-v4.2-1' of git://git.samba.org/jlayton/linux:
locks: inline posix_lock_file_wait and flock_lock_file_wait
nfs4: have do_vfs_lock take an inode pointer
locks: new helpers - flock_lock_inode_wait and posix_lock_inode_wait
locks: have flock_lock_file take an inode pointer instead of a filp
Revert "nfs: take extra reference to fl->fl_file when running a LOCKU operation"
Linus Torvalds [Wed, 15 Jul 2015 20:30:12 +0000 (13:30 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- Fix FPU refactoring ("kvm: x86: fix load xsave feature warning")
- Fix eager FPU mode (Cc stable)
- AMD bits of MTRR virtualization
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: fix load xsave feature warning
KVM: x86: apply guest MTRR virtualization on host reserved pages
KVM: SVM: Sync g_pat with guest-written PAT value
KVM: SVM: use NPT page attributes
KVM: count number of assigned devices
KVM: VMX: fix vmwrite to invalid VMCS
KVM: x86: reintroduce kvm_is_mmio_pfn
x86: hyperv: add CPUID bit for crash handlers
Linus Torvalds [Wed, 15 Jul 2015 20:17:31 +0000 (13:17 -0700)]
Merge tag 'arc-v4.2-rc3-fixes' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Makefile changes (top-level+ARC) reinstates -O3 builds (regression
since 3.16)
- IDU intc related fixes, IRQ affinity
- patch to make bitops safer for ARC
- perf fix from Alexey to remove signed PC braino
- Futex backend gets llock/scond support
* tag 'arc-v4.2-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: support HS38 releases
ARC: make sure instruction_pointer() returns unsigned value
ARC: slightly refactor macros for boot logging
ARC: Add llock/scond to futex backend
arc:irqchip: prepare for drivers/irqchip/irqchip.h removal
ARC: Make ARC bitops "safer" (add anti-optimization)
ARCv2: [axs103] bump CPU frequency from 75 to 90 MHZ
ARCv2: intc: IDU: Fix potential race in installing a chained IRQ handler
ARCv2: intc: IDU: support irq affinity
ARC: fix unused var wanring
ARC: Don't memzero twice in dma_alloc_coherent for __GFP_ZERO
ARC: Override toplevel default -O2 with -O3
kbuild: Allow arch Makefiles to override {cpp,ld,c}flags
ARCv2: guard SLC DMA ops with spinlock
ARC: Kconfig: better way to disable ARC_HAS_LLSC for ARC_CPU_750D
Linus Torvalds [Wed, 15 Jul 2015 20:12:44 +0000 (13:12 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"One improvement for the zcrypt driver, the quality attribute for the
hwrng device has been missing. Without it the kernel entropy seeding
will not happen automatically.
And six bug fixes, the most important one is the fix for the vector
register corruption due to machine checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/nmi: fix vector register corruption
s390/process: fix sfpc inline assembly
s390/dasd: fix kernel panic when alias is set offline
s390/sclp: clear upper register halves in _sclp_print_early
s390/oprofile: fix compile error
s390/sclp: fix compile error
s390/zcrypt: enable s390 hwrng to seed kernel entropy
Dave Kleikamp [Wed, 15 Jul 2015 17:52:47 +0000 (12:52 -0500)]
jfs: clean up jfs_rename and fix out of order unlock
The end of jfs_rename(), which is also used by the error paths,
included a call to IWRITE_UNLOCK(new_ip) after labels out1, out2
and out3. If we come in through these labels, IWRITE_LOCK() has not
been called yet.
In moving that call to the correct spot, I also moved some
exceptional truncate code earlier as well, since the early error
paths don't need to deal with it, and I renamed out4: to out_tx: so
a future patch by Jan Kara doesn't need to deal with renumbering or
confusing out-of-order labels.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Linus Torvalds [Wed, 15 Jul 2015 18:16:35 +0000 (11:16 -0700)]
Merge tag 'module-final-v4.2-rc1' of git://git./linux/kernel/git/paulg/linux
Pull final init.h/module.h code relocation from Paul Gortmaker:
"With the release of 4.2-rc2 done, we should not be seeing any new code
added that gets upset by this small code move, and we've banked yet
another complete week of testing with this move in place on top of
4.2-rc1 via linux-next to ensure that remained true.
Given that, I'd like to put it in now so that people formulating new
work for 4.3-rc1 will be exposed to the ever so slightly stricter (but
sensible) requirements wrt. whether they are needing init.h vs.
module.h macros, even if they are not using linux-next.
The diffstat of the move is slightly asymmetrical due to needing to
leave behind a couple #ifdef in the old location and add the same ones
to the new location, but other than that, it is a 1:1 move, complete
with the module_init/exit trailing semicolon that we can't fix. That
is, until/unless someone does a tree-wide sed fix of all the
approximately 800 currently in tree users relying on it"
* tag 'module-final-v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
module: relocate module_init from init.h to module.h
Linus Torvalds [Wed, 15 Jul 2015 18:14:10 +0000 (11:14 -0700)]
Merge tag 'trace-v4.2-rc1-fix' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fengguang Wu discovered a crash that happened to be because of the
branch tracer (traces unlikely and likely branches) when enabled with
certain debug options.
What happened was that various debug options like lockdep and
DEBUG_PREEMPT can cause parts of the branch tracer to recurse outside
its recursion protection. In fact, part of its recursion protection
used these features that caused the lockup. This cleans up the code a
little and makes the recursion protection a bit more robust"
* tag 'trace-v4.2-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Have branch tracer use recursive field of task struct
James Morris [Wed, 15 Jul 2015 11:46:59 +0000 (21:46 +1000)]
Merge tag 'tpm-fixes-for-4.2-rc2' of https://github.com/PeterHuewe/linux-tpmdd into for-linus
Christophe JAILLET [Mon, 13 Jul 2015 14:44:54 +0000 (16:44 +0200)]
intel_scu_ipc: move local memory initialization out of a mutex
'{ }' and memset will both reset the cbuf buffer.
Only once is enough and this can be done outside fo the mutex.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Johannes Thumshirn [Wed, 8 Jul 2015 15:23:00 +0000 (17:23 +0200)]
IB/core: Destroy ocrdma_dev_id IDR on module exit
Destroy ocrdma_dev_id IDR on module exit, reclaiming the allocated memory.
This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@
module_init(init);
@ defines_module_exit @
identifier exit;
@@
module_exit(exit);
@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@
DEFINE_IDR(idr);
@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
idr_destroy(&idr);
...
}
@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
+idr_destroy(&idr);
}
</SmPL>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Johannes Thumshirn [Wed, 8 Jul 2015 15:21:15 +0000 (17:21 +0200)]
IB/core: Destroy multcast_idr on module exit
Destroy multcast_idr on module exit, reclaiming the allocated memory.
This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@
module_init(init);
@ defines_module_exit @
identifier exit;
@@
module_exit(exit);
@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@
DEFINE_IDR(idr);
@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
idr_destroy(&idr);
...
}
@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
+idr_destroy(&idr);
}
</SmPL>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Doug Ledford [Thu, 9 Jul 2015 14:21:08 +0000 (10:21 -0400)]
IB/mlx4: Optimize do_slave_init
There is little chance our memory allocation will fail, so we can
combine initializing the work structs with allocating them instead of
looping through all of them once to allocate and again to initialize.
Then when we need to actually find out if our device is up or in the
process of going down, have all of our work structs batched up, take the
spin_lock once and only once, and do all of the batch under the one
spin_lock invocation instead of incurring all of the locked memory cycles
we would otherwise incur to take/release the spin_lock over and over
again.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Doug Ledford [Thu, 9 Jul 2015 14:16:12 +0000 (10:16 -0400)]
IB/mlx4: Fix memory leak in do_slave_init
We create a number of work structs to be queued up to a workqueue, and
on completion of the workqueue handler, the workqueue handler frees the
allocated memory. If, however, we don't queue the work struct because
the device is going down, then we need to free the memory ourselves.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Maninder Singh [Wed, 8 Jul 2015 04:13:35 +0000 (09:43 +0530)]
IB/mlx4: Optimize freeing of items on error unwind
On failure, we loop through all possible pointers and test them before
calling kfree. But really, why even attempt to free items we didn't
allocate when we can easily loop through exactly and only the devices
for which the original memory allocation succeeded and free just those.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Or Gerlitz [Thu, 25 Jun 2015 14:45:38 +0000 (17:45 +0300)]
IB/mlx4: Fix use of flow-counters for process_mad
For IB links, reading HCA flow counters through iboe_process_mad() should
be used when mlx4_ib_process_mad() is invoked only for VFs PMA queries and
exactly nothing else.
Fixes: 7193a141eb74 ('IB/mlx4: Set VF to read from QP counters')
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Vaishali Thakkar [Tue, 16 Jun 2015 11:43:05 +0000 (17:13 +0530)]
IB/ipath: Convert use of __constant_<foo> to <foo>
In little endian cases, the macros be16_to_cpu and cpu_to_be64
unfolds to __swab{16,64} which provides special case for constants.
In big endian cases, __constant_be16_to_cpu and be16_to_cpu
expand directly to the same expression. The same applies for
__constant_cpu_to_be64 and cpu_to_be64.
So, replace __constant_be16_to_cpu with be16_to_cpu and
__constant_cpu_to_be64 with cpu_to_be64, with the goal of getting
rid of the definition of __constant_be16_to_cpu and
__constant_cpu_to_be64 completely.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Erez Shitrit [Sun, 7 Jun 2015 10:36:11 +0000 (13:36 +0300)]
IB/ipoib: Set MTU to max allowed by mode when mode changes
When switching between modes (datagram / connected) change the MTU
accordingly.
datagram mode up to 4K, connected mode up to (64K - 0x10).
Signed-off-by: ELi Cohen <eli@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Yuval Shaia [Sun, 12 Jul 2015 08:24:09 +0000 (01:24 -0700)]
IB/ipoib: Scatter-Gather support in connected mode
By default, IPoIB-CM driver uses 64k MTU. Larger MTU gives better
performance.
This MTU plus overhead puts the memory allocation for IP based packets at
32 4k pages (order 5), which have to be contiguous.
When the system memory under pressure, it was observed that allocating 128k
contiguous physical memory is difficult and causes serious errors (such as
system becomes unusable).
This enhancement resolve the issue by removing the physically contiguous
memory requirement using Scatter/Gather feature that exists in Linux stack.
With this fix Scatter-Gather will be supported also in connected mode.
This change reverts some of the change made in commit
e112373fd6aa
("IPoIB/cm: Reduce connected mode TX object size").
The ability to use SG in IPoIB CM is possible because the coupling
between NETIF_F_SG and NETIF_F_CSUM was removed in commit
ec5f06156423 ("net: Kill link between CSUM and SG features.")
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Christian Marie <christian@ponies.io>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Carol L Soto [Thu, 11 Jun 2015 16:06:41 +0000 (11:06 -0500)]
IB/ucm: Fix bitmap wrap when devnum > IB_UCM_MAX_DEVICES
ib_ucm_release_dev clears the wrong bit if devnum is greater
than IB_UCM_MAX_DEVICES.
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Haggai Eran [Tue, 7 Jul 2015 14:45:13 +0000 (17:45 +0300)]
IB/ipoib: Prevent lockdep warning in __ipoib_ib_dev_flush
__ipoib_ib_dev_flush calls itself recursively on child devices, and lockdep
complains about locking vlan_rwsem twice (see below). Use down_read_nested
instead of down_read to prevent the warning.
=============================================
[ INFO: possible recursive locking detected ]
4.1.0-rc4+ #36 Tainted: G O
---------------------------------------------
kworker/u20:2/261 is trying to acquire lock:
(&priv->vlan_rwsem){.+.+..}, at: [<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
but task is already holding lock:
(&priv->vlan_rwsem){.+.+..}, at: [<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&priv->vlan_rwsem);
lock(&priv->vlan_rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by kworker/u20:2/261:
#0: ("%s""ipoib_flush"){.+.+..}, at: [<
ffffffff810827cc>] process_one_work+0x15c/0x760
#1: ((&priv->flush_heavy)){+.+...}, at: [<
ffffffff810827cc>] process_one_work+0x15c/0x760
#2: (&priv->vlan_rwsem){.+.+..}, at: [<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
stack backtrace:
CPU: 3 PID: 261 Comm: kworker/u20:2 Tainted: G O 4.1.0-rc4+ #36
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007
Workqueue: ipoib_flush ipoib_ib_dev_flush_heavy [ib_ipoib]
ffff8801c6c54790 ffff8801c9927af8 ffffffff81665238 0000000000000001
ffffffff825b5b30 ffff8801c9927bd8 ffffffff810bba51 ffff880100000000
ffffffff00000001 ffff880100000001 ffff8801c6c55428 ffff8801c6c54790
Call Trace:
[<
ffffffff81665238>] dump_stack+0x4f/0x6f
[<
ffffffff810bba51>] __lock_acquire+0x741/0x1820
[<
ffffffff810bcbf8>] lock_acquire+0xc8/0x240
[<
ffffffffa0791e2a>] ? __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
[<
ffffffff81669d2c>] down_read+0x4c/0x70
[<
ffffffffa0791e2a>] ? __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
[<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
[<
ffffffffa0791e4a>] __ipoib_ib_dev_flush+0x5a/0x2b0 [ib_ipoib]
[<
ffffffffa07920ba>] ipoib_ib_dev_flush_heavy+0x1a/0x20 [ib_ipoib]
[<
ffffffff81082871>] process_one_work+0x201/0x760
[<
ffffffff810827cc>] ? process_one_work+0x15c/0x760
[<
ffffffff81082ef0>] worker_thread+0x120/0x4d0
[<
ffffffff81082dd0>] ? process_one_work+0x760/0x760
[<
ffffffff81082dd0>] ? process_one_work+0x760/0x760
[<
ffffffff81088b7e>] kthread+0xfe/0x120
[<
ffffffff81088a80>] ? __init_kthread_worker+0x70/0x70
[<
ffffffff8166c6e2>] ret_from_fork+0x42/0x70
[<
ffffffff81088a80>] ? __init_kthread_worker+0x70/0x70
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Haggai Eran [Tue, 7 Jul 2015 14:45:12 +0000 (17:45 +0300)]
IB/ucma: Fix lockdep warning in ucma_lock_files
The ucma_lock_files() locks the mut mutex on two files, e.g. for migrating
an ID. Use mutex_lock_nested() to prevent the warning below.
=============================================
[ INFO: possible recursive locking detected ]
4.1.0-rc6-hmm+ #40 Tainted: G O
---------------------------------------------
pingpong_rpc_se/10260 is trying to acquire lock:
(&file->mut){+.+.+.}, at: [<
ffffffffa047ac55>] ucma_migrate_id+0xc5/0x248 [rdma_ucm]
but task is already holding lock:
(&file->mut){+.+.+.}, at: [<
ffffffffa047ac4b>] ucma_migrate_id+0xbb/0x248 [rdma_ucm]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&file->mut);
lock(&file->mut);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by pingpong_rpc_se/10260:
#0: (&file->mut){+.+.+.}, at: [<
ffffffffa047ac4b>] ucma_migrate_id+0xbb/0x248 [rdma_ucm]
stack backtrace:
CPU: 0 PID: 10260 Comm: pingpong_rpc_se Tainted: G O 4.1.0-rc6-hmm+ #40
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007
ffff8801f85b63d0 ffff880195677b58 ffffffff81668f49 0000000000000001
ffffffff825cbbe0 ffff880195677c38 ffffffff810bb991 ffff880100000000
ffff880100000000 ffff880100000001 ffff8801f85b7010 ffffffff8121bee9
Call Trace:
[<
ffffffff81668f49>] dump_stack+0x4f/0x6e
[<
ffffffff810bb991>] __lock_acquire+0x741/0x1820
[<
ffffffff8121bee9>] ? dput+0x29/0x320
[<
ffffffff810bcb38>] lock_acquire+0xc8/0x240
[<
ffffffffa047ac55>] ? ucma_migrate_id+0xc5/0x248 [rdma_ucm]
[<
ffffffff8166b901>] ? mutex_lock_nested+0x291/0x3e0
[<
ffffffff8166b6d5>] mutex_lock_nested+0x65/0x3e0
[<
ffffffffa047ac55>] ? ucma_migrate_id+0xc5/0x248 [rdma_ucm]
[<
ffffffff810baeed>] ? trace_hardirqs_on+0xd/0x10
[<
ffffffff8166b66e>] ? mutex_unlock+0xe/0x10
[<
ffffffffa047ac55>] ucma_migrate_id+0xc5/0x248 [rdma_ucm]
[<
ffffffffa0478474>] ucma_write+0xa4/0xb0 [rdma_ucm]
[<
ffffffff81200674>] __vfs_write+0x34/0x100
[<
ffffffff8112427c>] ? __audit_syscall_entry+0xac/0x110
[<
ffffffff810ec055>] ? current_kernel_time+0xc5/0xe0
[<
ffffffff812aa4d3>] ? security_file_permission+0x23/0x90
[<
ffffffff8120088d>] ? rw_verify_area+0x5d/0xe0
[<
ffffffff812009bb>] vfs_write+0xab/0x120
[<
ffffffff81201519>] SyS_write+0x59/0xd0
[<
ffffffff8112427c>] ? __audit_syscall_entry+0xac/0x110
[<
ffffffff8166ffee>] system_call_fastpath+0x12/0x76
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Wengang Wang [Mon, 6 Jul 2015 06:35:11 +0000 (14:35 +0800)]
rds: rds_ib_device.refcount overflow
Fixes: 3e0249f9c05c ("RDS/IB: add refcount tracking to struct rds_ib_device")
There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr
failed(mr pool running out). this lead to the refcount overflow.
A complain in line 117(see following) is seen. From vmcore:
s_ib_rdma_mr_pool_depleted is
2147485544 and rds_ibdev->refcount is -
2147475448.
That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely
to return ERR_PTR(-EAGAIN).
115 void rds_ib_dev_put(struct rds_ib_device *rds_ibdev)
116 {
117 BUG_ON(atomic_read(&rds_ibdev->refcount) <= 0);
118 if (atomic_dec_and_test(&rds_ibdev->refcount))
119 queue_work(rds_wq, &rds_ibdev->free_work);
120 }
fix is to drop refcount when rds_ib_alloc_fmr failed.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tatyana Nikolova [Thu, 2 Jul 2015 17:52:29 +0000 (12:52 -0500)]
RDMA/nes: Fix for incorrect recording of the MAC address
Fix for incorrect recording of the MAC address
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tatyana Nikolova [Thu, 2 Jul 2015 17:49:40 +0000 (12:49 -0500)]
RDMA/nes: Fix for resolving the neigh
Neighbor resolution doesn't work without this fix
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tatyana Nikolova [Thu, 2 Jul 2015 17:47:44 +0000 (12:47 -0500)]
RDMA/core: Fixes for port mapper client registration
Fixes to allow clients to make remove mapping requests, after
they have provided the user space service with the mapping
information, they are using when the service is restarted.
1) Adding IWPM_REG_VALID, IWPM_REG_INCOMPL and IWPM_REG_UNDEF
registration types for the port mapper clients and functions
to set/check the registration type.
2) If the port mapper user space service is not available to register
the client, then its registration stays IWPM_REG_UNDEF and the
registration isn't checked until the service becomes available
(no mappings are possible, if the user space service isn't running).
3) After the service is restarted, the user space port mapper pid is set
to valid and the client registration is set to IWPM_REG_INCOMPL
to allow the client to make remove mapping requests.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Amir Vadai [Wed, 1 Jul 2015 11:31:01 +0000 (14:31 +0300)]
IB/IPoIB: Fix bad error flow in ipoib_add_port()
Error values of ib_query_port() and ib_query_device() weren't propagated
correctly. Because of that, ipoib_add_port() could return NULL value,
which escaped the IS_ERR() check in ipoib_add_one() and we crashed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Matan Barak [Wed, 1 Jul 2015 11:31:02 +0000 (14:31 +0300)]
IB/mlx4: Do not attemp to report HCA clock offset on VFs
mlx4 VFs can provide CQE raw time-stamping services, but they
don't have the hca core clock mapped to their PCI bars.
As such, we should not attempt to query and report the clock offset
to user space for VFs. Doing so causes query_device over VFs to fail
with -ENOSUPP.
Fixes: 4b664c4355b2 ('IB/mlx4: Add support for CQ time-stamping')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Erez Shitrit [Thu, 25 Jun 2015 14:13:22 +0000 (17:13 +0300)]
IB/cm: Do not queue work to a device that's going away
Whenever ib_cm gets remove_one call, like when there is a hot-unplug
event, the driver should mark itself as going_down and confirm that no
new works are going to be queued for that device.
so, the order of the actions are:
1. mark the going_down bit.
2. flush the wq.
3. [make sure no new works for that device.]
4. unregister mad agent.
otherwise, works that are already queued can be scheduled after the mad
agent was freed.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Sagi Grimberg [Thu, 25 Jun 2015 10:34:15 +0000 (13:34 +0300)]
IB/srp: Avoid using uninitialized variable
We might return res which is not initialized. Also
reduce code duplication by exporting srp_parse_tmo so
srp_tmo_set can reuse it.
Detected by Coverity.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Vaishali Thakkar [Wed, 24 Jun 2015 04:42:13 +0000 (10:12 +0530)]
IB/srpt: Convert use of __constant_cpu_to_beXX to cpu_to_beXX
In little endian cases, the macro cpu_to_be{16,32,64} unfolds to
__swab{16,32,64} which provides special case for constants. In
big endian cases, __constant_cpu_to_be{16,32,64} and
cpu_to_be{16,32,64} expand directly to the same expression. So,
replace __constant_cpu_to_be{16,32,64} with cpu_to_be{16,32,64}
with the goal of getting rid of the definitions of
__constant_cpu_to_be{16,32,64} completely.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@expression x;@@
(
- __constant_cpu_to_be16(x)
+ cpu_to_be16(x)
|
- __constant_cpu_to_be32(x)
+ cpu_to_be32(x)
|
- __constant_cpu_to_be64(x)
+ cpu_to_be64(x)
)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ira Weiny [Thu, 25 Jun 2015 13:52:50 +0000 (09:52 -0400)]
IB/mad: Remove improper use of BUG_ON
We recently added BUG_ON's which were inappropriate for a condition which
should never happen. Change these to be WARN_ON_ONCE as a debugging aid.
Fixes: 4cd7c9479aff ('IB/mad: Add support for additional MAD info to/from drivers')
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ira Weiny [Thu, 25 Jun 2015 16:04:49 +0000 (12:04 -0400)]
IB/mad: Fix compare between big endian and cpu endian
The define OPA_LID_PERMISSIVE is big endian and was compared to the
cpu endian variable opa_drslid.
Problem caught by 0-day build infrastructure.
Fixes: 8e4349d13f33 (IB/mad: Add final OPA MAD processing)
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: John, Jubin <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Hal Rosenstock [Mon, 29 Jun 2015 13:57:00 +0000 (09:57 -0400)]
IB: Add rdma_cap_ib_switch helper and use where appropriate
Persuant to Liran's comments on node_type on linux-rdma
mailing list:
In an effort to reform the RDMA core and ULPs to minimize use of
node_type in struct ib_device, an additional bit is added to
struct ib_device for is_switch (IB switch). This is needed
to be initialized by any IB switch device driver. This is a
NEW requirement on such device drivers which are all
"out of tree".
In addition, an ib_switch helper was added to ib_verbs.h
based on the is_switch device bit rather than node_type
(although those should be consistent).
The RDMA core (MAD, SMI, agent, sa_query, multicast, sysfs)
as well as (IPoIB and SRP) ULPs are updated where
appropriate to use this new helper. In some cases,
the helper is now used under the covers of using
rdma_[start end]_port rather than the open coding
previously used.
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Jarkko Sakkinen [Wed, 24 Jun 2015 14:14:55 +0000 (17:14 +0300)]
tpm, tpm_crb: fail when TPM2 ACPI table contents look corrupted
At least some versions of AMI BIOS have corrupted contents in the TPM2
ACPI table and namely the physical address of the control area is set to
zero.
This patch changes the driver to fail gracefully when we observe a zero
address instead of continuing to ioremap.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Jason Gunthorpe [Tue, 30 Jun 2015 19:15:31 +0000 (13:15 -0600)]
tpm: Fix initialization of the cdev
When a cdev is contained in a dynamic structure the cdev parent kobj
should be set to the kobj that controls the lifetime of the enclosing
structure. In TPM's case this is the embedded struct device.
Also, cdev_init 0's the whole structure, so all sets must be after,
not before. This fixes module ref counting and cdev.
Cc: <stable@vger.kernel.org>
Fixes: 313d21eeab92 ("tpm: device class for tpm")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Linus Torvalds [Mon, 13 Jul 2015 18:18:25 +0000 (11:18 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Missing list head init in bluetooth hidp session creation, from Tedd
Ho-Jeong An.
2) Don't leak SKB in bridge netfilter error paths, from Florian
Westphal.
3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
Grall.
4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
Baechle.
5) Fix race between rhashtable resize events and table walks, from Phil
Sutter.
6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
Daniel Borkmann.
7) Missing security layer socket state initialization in tipc code,
from Stephen Smalley.
8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
Denys Vlasenko.
9) Missing minor_idr destroy on module unload on macvtap driver, from
Johannes Thumshirn.
10) Various pktgen kernel thread races, from Oleg Nesterov.
11) Fix races that can cause packets to be processed in the backlog even
after a device attached to that SKB has been fully unregistered.
From Julian Anastasov.
12) bcmgenet driver doesn't account packet drops vs. errors properly,
fix from Petri Gynther.
13) Array index validation and off by one fix in DSA layer from Florian
Fainelli
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
can: replace timestamp as unique skb attribute
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
can: c_can: Fix default pinmux glitch at init
can: rcar_can: unify error messages
can: rcar_can: print request_irq() error code
can: rcar_can: fix typo in error message
can: rcar_can: print signed IRQ #
can: rcar_can: fix IRQ check
net: dsa: Fix off-by-one in switch address parsing
net: dsa: Test array index before use
net: switchdev: don't abort unsupported operations
net: bcmgenet: fix accounting of packet drops vs errors
cdc_ncm: update specs URL
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
bridge: mdb: allow the user to delete mdb entry if there's a querier
net: call rcu_read_lock early in process_backlog
net: do not process device backlog during unregistration
bridge: fix potential crash in __netdev_pick_tx()
net: axienet: Fix devm_ioremap_resource return value check
...
Linus Torvalds [Mon, 13 Jul 2015 17:33:22 +0000 (10:33 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a duplicate dma_unmap_sg call in omap-des and reentrancy
bugs in the powerpc nx driver which may cause bogus output or worse
memory corruption"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: nx - Fix reentrancy bugs
crypto: omap-des - Fix unmapping of dma channels
Jeff Layton [Sat, 11 Jul 2015 10:43:03 +0000 (06:43 -0400)]
locks: inline posix_lock_file_wait and flock_lock_file_wait
They just call file_inode and then the corresponding *_inode_file_wait
function. Just make them static inlines instead.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Jeff Layton [Sat, 11 Jul 2015 10:43:03 +0000 (06:43 -0400)]
nfs4: have do_vfs_lock take an inode pointer
Now that we have file locking helpers that can deal with an inode
instead of a filp, we can change the NFSv4 locking code to use that
instead.
This should fix the case where we have a filp that is closed while flock
or OFD locks are set on it, and the task is signaled so that it doesn't
wait for the LOCKU reply to come in before the filp is freed. At that
point we can end up with a use-after-free with the current code, which
relies on dereferencing the fl_file in the lock request.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Jeff Layton [Sat, 11 Jul 2015 10:43:02 +0000 (06:43 -0400)]
locks: new helpers - flock_lock_inode_wait and posix_lock_inode_wait
Allow callers to pass in an inode instead of a filp.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Jeff Layton [Sat, 11 Jul 2015 10:43:02 +0000 (06:43 -0400)]
locks: have flock_lock_file take an inode pointer instead of a filp
...and rename it to better describe how it works.
In order to fix a use-after-free in NFS, we need to be able to remove
locks from an inode after the filp associated with them may have already
been freed. flock_lock_file already only dereferences the filp to get to
the inode, so just change it so the callers do that.
All of the callers already pass in a lock request that has the fl_file
set properly, so we don't need to pass it in individually. With that
change it now only dereferences the filp to get to the inode, so just
push that out to the callers.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Jeff Layton [Sat, 11 Jul 2015 10:43:01 +0000 (06:43 -0400)]
Revert "nfs: take extra reference to fl->fl_file when running a LOCKU operation"
This reverts commit
db2efec0caba4f81a22d95a34da640b86c313c8e.
William reported that he was seeing instability with this patch, which
is likely due to the fact that it can cause the kernel to take a new
reference to a filp after the last reference has already been put.
Revert this patch for now, as we'll need to fix this in another way.
Cc: stable@vger.kernel.org
Reported-by: William Dauchy <william@gandi.net>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Heiko Carstens [Tue, 7 Jul 2015 06:40:49 +0000 (08:40 +0200)]
s390/nmi: fix vector register corruption
If a machine check happens, the machine has the vector facility installed
and the extended save area exists, the cpu will save vector register
contents into the extended save area. This is regardless of control
register 0 contents, which enables and disables the vector facility during
runtime.
On each machine check we should validate the vector registers. The current
code however tries to validate the registers only if the running task is
using vector registers in user space.
However even the current code is broken and causes vector register
corruption on machine checks, if user space uses them:
the prefix area contains a pointer (absolute address) to the machine check
extended save area. In order to save some space the save area was put into
an unused area of the second prefix page.
When validating vector register contents the code uses the absolute address
of the extended save area, which is wrong. Due to prefixing the vector
instructions will then access contents using absolute addresses instead
of real addresses, where the machine stored the contents.
If the above would work there is still the problem that register validition
would only happen if user space uses vector registers. If kernel space uses
them also, this may also lead to vector register content corruption:
if the kernel makes use of vector instructions, but the current running
user space context does not, the machine check handler will validate
floating point registers instead of vector registers.
Given the fact that writing to a floating point register may change the
upper halve of the corresponding vector register, we also experience vector
register corruption in this case.
Fix all of these issues, and always validate vector registers on each
machine check, if the machine has the vector facility installed and the
extended save area is defined.
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 6 Jul 2015 13:02:37 +0000 (15:02 +0200)]
s390/process: fix sfpc inline assembly
The sfpc inline assembly within execve_tail() may incorrectly set bits
28-31 of the sfpc instruction to a value which is not zero.
These bits however are currently unused and therefore should be zero
so we won't get surprised if these bits will be used in the future.
Therefore remove the second operand from the inline assembly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Haberland [Fri, 10 Jul 2015 08:47:09 +0000 (10:47 +0200)]
s390/dasd: fix kernel panic when alias is set offline
The dasd device driver selects which (alias or base) device is used
for a given requests when the request is build. If the chosen alias
device is set offline before the request gets queued to the device
queue the starting function may use device structures that are
already freed. This might lead to a hanging offline process or a
kernel panic.
Add a check to the starting function that returns the request to the
upper layer if the device is already in offline processing.
In addition to that prevent that an alias device that's already in
offline processing gets chosen as start device.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Vineet Gupta [Sun, 12 Jul 2015 07:46:50 +0000 (13:16 +0530)]
ARCv2: support HS38 releases
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Alexey Brodkin [Mon, 13 Jul 2015 07:25:17 +0000 (10:25 +0300)]
ARC: make sure instruction_pointer() returns unsigned value
Currently instruction_pointer() returns pt_regs->ret and so return value
is of type "long", which implicitly stands for "signed long".
While that's perfectly fine when dealing with 32-bit values if return
value of instruction_pointer() gets assigned to 64-bit variable sign
extension may happen.
And at least in one real use-case it happens already.
In perf_prepare_sample() return value of perf_instruction_pointer()
(which is an alias to instruction_pointer() in case of ARC) is assigned
to (struct perf_sample_data)->ip (which type is "u64").
And what we see if instuction pointer points to user-space application
that in case of ARC lays below 0x8000_0000 "ip" gets set properly with
leading 32 zeros. But if instruction pointer points to kernel address
space that starts from 0x8000_0000 then "ip" is set with 32 leadig
"f"-s. I.e. id instruction_pointer() returns 0x8100_0000, "ip" will be
assigned with 0xffff_ffff__8100_0000. Which is obviously wrong.
In particular that issuse broke output of perf, because perf was unable
to associate addresses like 0xffff_ffff__8100_0000 with anything from
/proc/kallsyms.
That's what we used to see:
----------->8----------
6.27% ls [unknown] [k] 0xffffffff8046c5cc
2.96% ls libuClibc-0.9.34-git.so [.] memcpy
2.25% ls libuClibc-0.9.34-git.so [.] memset
1.66% ls [unknown] [k] 0xffffffff80666536
1.54% ls libuClibc-0.9.34-git.so [.] 0x000224d6
1.18% ls libuClibc-0.9.34-git.so [.] 0x00022472
----------->8----------
With that change perf output looks much better now:
----------->8----------
8.21% ls [kernel.kallsyms] [k] memset
3.52% ls libuClibc-0.9.34-git.so [.] memcpy
2.11% ls libuClibc-0.9.34-git.so [.] malloc
1.88% ls libuClibc-0.9.34-git.so [.] memset
1.64% ls [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.41% ls [kernel.kallsyms] [k] __d_lookup_rcu
----------->8----------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-linux-dev@synopsys.com
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
David S. Miller [Mon, 13 Jul 2015 05:24:01 +0000 (22:24 -0700)]
Merge tag 'linux-can-fixes-for-4.2-
20150712' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-12
this is a pull request of 8 patchs for net/master.
Sergei Shtylyov contributes 5 patches for the rcar_can driver, fixing the IRQ
check and several info and error messages. There are two patches by J.D.
Schroeder and Roger Quadros for the c_can driver and dra7x-evm device tree,
which precent a glitch in the DCAN1 pinmux. Oliver Hartkopp provides a better
approach to make the CAN skbs unique, the timestamp is replaced by a counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Ungerer [Wed, 8 Jul 2015 07:02:08 +0000 (17:02 +1000)]
m68k: enable PCI support for m5475evb defconfig
The ColdFire M5475 on the m5475evb board supports a PCI bus, lets
enable it for the defconfig to get better build and test coverage.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Wed, 8 Jul 2015 06:54:13 +0000 (16:54 +1000)]
m68k: fix io functions for ColdFire/MMU/PCI case
The inb/outb/... family of IO methods end up being multiply defined when
building PCI support for the ColdFire. Compiling gives this:
CC init/main.o
In file included from ./arch/m68k/include/asm/io.h:4:0,
from include/linux/bio.h:30,
from include/linux/blkdev.h:18,
from init/main.c:75:
./arch/m68k/include/asm/io_mm.h:420:0: warning: "inb" redefined
./arch/m68k/include/asm/io_mm.h:108:0: note: this is the location of the previous definition
...
The ColdFire/PCI case defines its own IO access methods, so no others
should be defined or used in this case. Conditionally disable other
definitions that clash with it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 06:34:34 +0000 (16:34 +1000)]
m68knommu: update defconfig for ColdFire m5475evb
No change to active configuration settings, updated to match current
Kconfigs only.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 06:33:08 +0000 (16:33 +1000)]
m68knommu: update defconfig for ColdFire m5407c3
No change to active configuration settings, updated to match current
Kconfigs only.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 06:31:56 +0000 (16:31 +1000)]
m68knommu: update defconfig for ColdFire m5307c3
No change to active configuration settings, updated to match current
Kconfigs only.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 06:31:30 +0000 (16:31 +1000)]
m68knommu: update defconfig for ColdFire m5275evb
No change to active configuration settings, updated to match current
Kconfigs only.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 06:30:58 +0000 (16:30 +1000)]
m68knommu: update defconfig for ColdFire m5272c3
No change to active configuration settings, updated to match current
Kconfigs only.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 06:29:17 +0000 (16:29 +1000)]
m68knommu: update defconfig for ColdFire m5249evb
No change to active configuration settings, updated to match current
Kconfigs only.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 06:27:29 +0000 (16:27 +1000)]
m68knommu: update defconfig for m5208evb
No change to active configuration settings, updated to match current
Kconfigs only.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 7 Jul 2015 05:44:02 +0000 (15:44 +1000)]
m68knommu: make ColdFire SoC selection a choice
It would be nice if we could support multiple ColdFire SoC types in a
single binary - but currently the code simply does not support it.
Change the SoC selection config options to be a choice instead of
individual selectable entries.
This fixes problems with building allnoconfig, and means that a sane
linux kernel is generated for a single ColdFire SoC type.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Greg Ungerer [Tue, 7 Jul 2015 05:01:53 +0000 (15:01 +1000)]
m68knommu: improve the clock configuration defaults
Create some intelligent default settings for each ColdFire SoC type
in the configuration entry for CONFIG_CLOCK_FREQ.
The ColdFire clock frequency is configurable at build time. There is a
lot of variation in the frequency of operation on specific ColdFire based
boards. But we can choose a default that matches the maximum frequency
of clock operation for a particular ColdFire part. That is typically
the most common clock setting.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Greg Ungerer [Tue, 7 Jul 2015 04:21:21 +0000 (14:21 +1000)]
m68knommu: force setting of CONFIG_CLOCK_FREQ for ColdFire
It is possible to disable the clock selection at configuration time,
but for ColdFire targets we always expect a clock frequency to be
selected. This results in the following compile time error:
CC arch/m68k/kernel/asm-offsets.s
In file included from ./arch/m68k/include/asm/timex.h:14:0,
from include/linux/timex.h:65,
from include/linux/sched.h:19,
from arch/m68k/kernel/asm-offsets.c:14:
./arch/m68k/include/asm/coldfire.h:25:2: error: #error "Don't know what your ColdFire CPU clock frequency is??"
Remove CONFIG_CLOCK_SELECT completely and always enable CONFIG_CLOCK_FREQ
for ColdFire.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Linus Torvalds [Sun, 12 Jul 2015 22:10:30 +0000 (15:10 -0700)]
Linux 4.2-rc2
Linus Torvalds [Sun, 12 Jul 2015 22:00:20 +0000 (15:00 -0700)]
Revert "drm/i915: Use crtc_state->active in primary check_plane func"
This reverts commit
dec4f799d0a4c9edae20512fa60b0a36f3299ca2.
Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:
crtc_state = state->base.state ?
intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;
So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.
There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 12 Jul 2015 21:09:36 +0000 (14:09 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"Fixes for this cycle regression in overlayfs and a couple of
long-standing (== all the way back to 2.6.12, at least) bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
Linus Torvalds [Sun, 12 Jul 2015 20:55:24 +0000 (13:55 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A fair number of 4.2 fixes also because Markos opened the flood gates.
- Patch up the math used calculate the location for the page bitmap.
- The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
around was causing issues on non-Malta platforms, so move the code
to a Malta specific location.
- A spelling fix replicated through several files.
- Fix to the emulation of an R2 instruction for R6 cores.
- Fix the JR emulation for R6.
- Further patching of mindless 64 bit issues.
- Ensure the kernel won't crash on CPUs with L2 caches with >= 8
ways.
- Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.
- Fix cache flushing for multithreaded cores.
- A build fix"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
MIPS: c-r4k: Fix cache flushing for MT cores
Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
MIPS: cps-vec: Use macros for various arithmetics and memory operations
MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
MIPS: Fix erroneous JR emulation for MIPS R6
MIPS: Fix branch emulation for BLTC and BGEC instructions
MIPS: kernel: traps: Fix broken indentation
MIPS: bootmem: Don't use memory holes for page bitmap
MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
MIPS, CPUFREQ: Fix spelling of Institute.
MIPS: Lemote 2F: Fix build caused by recent mass rename.
Oliver Hartkopp [Fri, 26 Jun 2015 09:58:19 +0000 (11:58 +0200)]
can: replace timestamp as unique skb attribute
Commit
514ac99c64b "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit
36c01245eb8 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Tue, 7 Jul 2015 14:27:57 +0000 (17:27 +0300)]
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
Driver core sets "default" pinmux on on probe and CAN driver
sets "sleep" pinmux during register. This causes a small window
where the CAN pins are in "default" state with the DCAN module
being disabled.
Change the "default" state to be like sleep so this glitch is
avoided. Add a new "active" state that is used by the driver
when CAN is actually active.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
J.D. Schroeder [Wed, 8 Jul 2015 11:38:12 +0000 (14:38 +0300)]
can: c_can: Fix default pinmux glitch at init
The previous change
3973c526ae9c (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit
ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:51:34 +0000 (03:51 +0300)]
can: rcar_can: unify error messages
All the error messages in the driver but the ones from devm_clk_get() failures
use similar format. Make those two messages consitent with others.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:50:35 +0000 (03:50 +0300)]
can: rcar_can: print request_irq() error code
Also print the error code when the request_irq() call fails in rcar_can_open(),
rewording the error message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:34:55 +0000 (03:34 +0300)]
can: rcar_can: fix typo in error message
Fix typo in the first error message printed by rcar_can_open().
Based on the original patch by Vladimir Barinov.
Fixes: 862e2b6af941 ("can: rcar_can: support all input clocks")
Reported-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:33:53 +0000 (03:33 +0300)]
can: rcar_can: print signed IRQ #
Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of type *int*, so the "%d" format needs to be used instead.
While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:32:46 +0000 (03:32 +0300)]
can: rcar_can: fix IRQ check
rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:
error requesting interrupt
fffffffa
because rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.
Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Linus Torvalds [Sun, 12 Jul 2015 17:02:38 +0000 (10:02 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- the high latency PIT detection fix, which slipped through the cracks
for rc1
- a regression fix for the early printk mechanism
- the x86 part to plug irq/vector related hotplug races
- move the allocation of the espfix pages on cpu hotplug to non atomic
context. The current code triggers a might_sleep() warning.
- a series of KASAN fixes addressing boot crashes and usability
- a trivial typo fix for Kconfig help text
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
x86/irq: Retrieve irq data after locking irq_desc
x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
x86/irq: Plug irq vector hotplug race
x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
x86/espfix: Init espfix on the boot CPU side
x86/espfix: Add 'cpu' parameter to init_espfix_ap()
x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
x86/kasan: Add message about KASAN being initialized
x86/kasan: Fix boot crash on AMD processors
x86/kasan: Flush TLBs after switching CR3
x86/kasan: Fix KASAN shadow region page tables
x86/init: Clear 'init_level4_pgt' earlier
x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()
Linus Torvalds [Sun, 12 Jul 2015 16:36:59 +0000 (09:36 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"This update from the timer departement contains:
- A series of patches which address a shortcoming in the tick
broadcast code.
If the broadcast device is not available or an hrtimer emulated
broadcast device, some of the original assumptions lead to boot
failures. I rather plugged all of the corner cases instead of only
addressing the issue reported, so the change got a little larger.
Has been extensivly tested on x86 and arm.
- Get rid of the last holdouts using do_posix_clock_monotonic_gettime()
- A regression fix for the imx clocksource driver
- An update to the new state callbacks mechanism for clockevents.
This is required to simplify the conversion, which will take place
in 4.3"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Prevent NULL pointer dereference
time: Get rid of do_posix_clock_monotonic_gettime
cris: Replace do_posix_clock_monotonic_gettime()
tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
tick/broadcast: Handle spurious interrupts gracefully
tick/broadcast: Check for hrtimer broadcast active early
tick/broadcast: Return busy when IPI is pending
tick/broadcast: Return busy if periodic mode and hrtimer broadcast
tick/broadcast: Move the check for periodic mode inside state handling
tick/broadcast: Prevent deep idle if no broadcast device available
tick/broadcast: Make idle check independent from mode and config
tick/broadcast: Sanity check the shutdown of the local clock_event
tick/broadcast: Prevent hrtimer recursion
clockevents: Allow set-state callbacks to be optional
clocksource/imx: Define clocksource for mx27
Linus Torvalds [Sun, 12 Jul 2015 16:15:02 +0000 (09:15 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a cpu hotplug race vs. interrupt descriptors:
Prevent irq setup/teardown across the cpu starting/dying parts of cpu
hotplug so that the starting/dying cpu has a stable view of the
descriptor space. This has been an issue for all architectures in the
cpu dying phase, where interrupts are migrated away from the dying
cpu. In the starting phase its mostly a x86 issue vs the vector space
update"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hotplug: Prevent alloc/free of irq descriptors during cpu up/down
Al Viro [Wed, 8 Jul 2015 01:42:38 +0000 (02:42 +0100)]
freeing unlinked file indefinitely delayed
Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course). However, there's one case where that
does *not* happen. Namely, if you open it by fhandle with cold dcache,
then unlink() and close().
In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal. In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()). The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in. As the result, we have the final iput() delayed
indefinitely. It's trivial to reproduce -
void flush_dcache(void)
{
system("mount -o remount,rw /");
}
static char buf[20 * 1024 * 1024];
main()
{
int fd;
union {
struct file_handle f;
char buf[MAX_HANDLE_SZ];
} x;
int m;
x.f.handle_bytes = sizeof(x);
chdir("/root");
mkdir("foo", 0700);
fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
close(fd);
name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
flush_dcache();
fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
unlink("foo/bar");
write(fd, buf, sizeof(buf));
system("df ."); /* 20Mb eaten */
close(fd);
system("df ."); /* should've freed those 20Mb */
flush_dcache();
system("df ."); /* should be the same as #2 */
}
will spit out something like
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 283282 21692 93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).
Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 12 Jul 2015 14:39:45 +0000 (10:39 -0400)]
fix a braino in ovl_d_select_inode()
when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 12 Jul 2015 14:34:29 +0000 (10:34 -0400)]
9p: don't leave a half-initialized inode sitting around
Cc: stable@vger.kernel.org # all branches
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David S. Miller [Sun, 12 Jul 2015 06:25:16 +0000 (23:25 -0700)]
Merge branch 'dsa-of-parsing-fixes'
Florian Fainelli says:
====================
net: dsa: OF parsing fixes
This patch series fixes two small parsing issues, the first one was
reported by Dan, the second came after looking more closely at the
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 12 Jul 2015 01:02:11 +0000 (18:02 -0700)]
net: dsa: Fix off-by-one in switch address parsing
cd->sw_addr is used as a MDIO bus address, which cannot exceed
PHY_MAX_ADDR (32), our check was off-by-one.
Fixes: 5e95329b701c ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 12 Jul 2015 01:02:10 +0000 (18:02 -0700)]
net: dsa: Test array index before use
port_index is used an index into an array, and this information comes
from Device Tree, make sure that port_index is not equal to the array
size before using it. Move the check against port_index earlier in the
loop.
Fixes: 5e95329b701c: ("dsa: add device tree bindings to register DSA switches")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 10 Jul 2015 23:48:58 +0000 (19:48 -0400)]
net: switchdev: don't abort unsupported operations
There is no need to abort attribute setting or object addition, if the
prepare phase returned operation not supported.
Thus, abort these two transactions only if the error is not -EOPNOTSUPP.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Fri, 10 Jul 2015 23:20:00 +0000 (16:20 -0700)]
net: bcmgenet: fix accounting of packet drops vs errors
bcmgenet driver needs to separate packet drops from packet errors.
When the driver has to drop a *good* packet, due to lack of buffers or
replacement skbs, increment only dev->stats.[rx|tx]_dropped.
When the driver encounters a bad Rx packet or Tx error, increment only
dev->stats.[rx|tx]_errors + relevant detailed error counter.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enrico Mioso [Sat, 11 Jul 2015 15:30:01 +0000 (17:30 +0200)]
cdc_ncm: update specs URL
Update referenced specs link to reflect actual file version and location.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 12 Jul 2015 03:44:31 +0000 (20:44 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/djbw/nvdimm
Pull libnvdimm fixes from Dan Williams:
"1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
bug fixes (patches 1-6)
2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).
Granted these are slightly large for a -rc update. They have been
out for review in one form or another since the end of May and were
deferred from the merge window while we settled on the "PMEM API"
for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
and wmb_pmem).
Now that those apis are merged we implement them in the BLK driver
to guarantee that mmio aperture moves stay ordered with respect to
incoming read/write requests, and that writes are flushed through
those mmio-windows and platform-buffers to be persistent on media.
These pass the sub-system unit tests with the updates to
tools/testing/nvdimm, and have received a successful build-report from
the kbuild robot (468 configs).
With acks from Rafael for the touches to drivers/acpi/"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
nfit: fix smatch "use after null check" report
nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
libnvdimm: smatch cleanups in __nd_ioctl
sparse: fix misplaced __pmem definition
This page took 0.054868 seconds and 5 git commands to generate.