qla2xxx: Shutdown board on thermal shutdown aen.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Add ram area DDR for fwdump template entry T262.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: Remove sysfs node fw_dump_template.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Update lpfc version to 11.2.0.0

Update lpfc version to 11.2.0.0

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Copyright updates

Copyright updates

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Disable FDMI probing if not connected to a fabric

Disable FDMI probing if not connected to a fabric

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Correct issue with ioremap() call on 32bit kernel

Correct issue with ioremap() call on 32bit kernel

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Re-organize source for easier driver attribute management

Re-organize source for easier driver attribute management

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Remove global lpfc_sli_mode attribute in leiu of per-hba lpfc_sli_mode

Remove global lpfc_sli_mode attribute in leiu of per-hba lpfc_sli_mode

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Remove global lpfc_delay_discovery attribute in leiu of per-hba lpfc_delay_discovery

Remove global lpfc_delay_discovery attribute in leiu of per-hba
lpfc_delay_discovery

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Remove global lpfc_enable_npiv attribute in leiu of per-hba lpfc_enable_npiv

Remove global lpfc_enable_npiv attribute in leiu of per-hba lpfc_enable_npiv

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Correct Port reset resulting in FC port going offline

Correct Port reset resulting in FC port going offline

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Add support for XLane LUN priority

Add support for XLane LUN priority

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Correct RDP response Revision location

Correct RDP response Revision location

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Re-organize source for easier device-id management

Re-organize source for easier device-id management

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Correct FCOE discovery to avoid loss of storage devices after system reboot

Correct FCOE discovery to avoid loss of storage devices after system reboot

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Fix SLI mode 2 config failure

Fix SLI mode 2 config failure

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Add MDS Diagnostics Support

Add MDS Diagnostics Support

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Add sysfs proc_name support

Add sysfs proc_name support

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Reject RDP ELS if port has no login

Reject RDP ELS if port has no login

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Correct Buffer credit descriptor values in RDP response

Correct Buffer credit descriptor values in RDP response

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Add recovery from adapter parity errors on some SLI4 adapters

Add recovery from adapter parity errors on some SLI4 adapters

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Correct RDP response sizing issue

Correct RDP response sizing issue

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

lpfc: Fix Transgression Flag of Optical Element descriptor for RDP on Linux

Fix Transgression Flag of Optical Element descriptor for RDP on Linux

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ibmvfc: prevent a potential deadlock

My static checker complains that we need to unlock on this path.  Seems
true.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

usb: MAINTAINERS: Oliver Neukum is the new uas maintainer

Oliver Neukum is taking over uas maintainership from me and Gerd
Hoffmann.

Cc: Oliver Neukum <oneukum@suse.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: remove the disable_blk_mq host flag

We've had scsi-mq for 2.5 years now, so we can remove the unused flag to
disable the code on a per-host basis that was put in for unexpected
emergencies during bringup.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: tc-dwc-g210 driver fix for 20-bit RMMI

The code was checking on PA_CONNECTEDRXLANES and PA_CONNECTEDTXLANES
attributes to program the Lane#1 attributes. The correct attributes are
PA_AVAILRXDATALANES and PA_AVAILTXDATALANES respectively.

Signed-off-by: Manjunath M B <manjumb@synopsys.com>
Tested-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: Fix panic when aer correct error occurred

The _scsih_pci_mmio_enabled called if scsih_pci_error_detected returns
PCI_ERS_RESULT_CAN_RECOVER, at this point, read/write to the device
still works, no need to reset slot.

Or the mpt3sas_base_map_resources in scsih_pci_slot_reset will fail,
and iounamp ioc->chip, then we will meet issue when read ioc->chip
in mpt3sas_base_get_iocstate from _base_fault_reset_work.

Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

qla2xxx: setup data needed in ISR before setting up the ISR

qla2xxx first calls request_irq() and then does the setup of the queue
entry data needed in the interrupt handlers in when using MSI-X. This
could lead to a NULL pointer dereference when an IRQ fires between the
request_irq() call and the assignment of the qentry data structure to
the rsp->msix field. A possible case for such a race would be in the
kdump case when the HBA's IRQs are still enabled but the driver is
undergoing a new initialisation and thus is not aware of already
activated IRQs in the HBA.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipr: Increase MSIX vectors number

Increase MSIX vectors from 2 to 16 by default.

Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipr: Add new CCIN for new adapters support

Add the appropriate definitions and table entries for new adapters
support.

Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: remove current_cmnd field from struct scsi_device

The field is only used by the 53c700 driver, so move it into the
driver-private device data instead of having it in the common structure.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

megaraid_sas: Do not fire MR_DCMD_PD_LIST_QUERY to controllers which do not support it

There was an issue reported by Lucz Geza on Dell Perc 6i. As per issue
reported, megaraid_sas driver goes into an infinite error reporting loop
as soon as there is a change in the status of one of the
arrays (degrade, resync online etc ).  Below are the error logs reported
continuously-

Jun 25 08:49:30 ns8 kernel: [  757.757017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [  757.778017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [  757.799017] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [  757.820018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115
Jun 25 08:49:30 ns8 kernel: [  757.841018] megaraid_sas 0000:02:00.0: DCMD failed/not supported by firmware: megasas_get_pd_list 4115

This issue is very much specific to controllers which do not support
DCMD- MR_DCMD_PD_LIST_QUERY.  In case of any hotplugging/rescanning of
drives, AEN thread will be scheduled by driver and fire DCMD-
MR_DCMD_PD_LIST_QUERY and if this DCMD is failed then driver will fail
this event processing and will not go ahead for further events. This
will cause infinite loop of same event getting retried infinitely and
causing above mentioned logs.

Fix for this problem is: not to fire DCMD MR_DCMD_PD_LIST_QUERY for
controllers which do not support it and send DCMD SUCCESS status to AEN
function so that it can go ahead with other event processing.

Reported-by: Lucz Geza <geza@lucz.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fcoe: use defines from ethtool for 20Gbit and 40Gbit speeds

Use defines from ethtool for 20Gbit and 40Gbit speeds instead of magic
numbers.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fcoe: Update multicast addresses on FIP mode change

When the FIP mode is changed we need to update the multicast addresses
to ensure we get the correct frames.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fcoe: fcoe->realdev is always set

'->realdev' is always set, so this check is pointless.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fcoe: use enum for fip_mode

The FIP mode is independent on the FIP state machine, so use a separate
enum for that instead of overloading it with state machine values.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fc_fip: Update to latest FC-BB-6 draft

Update to latest FC-BB-6 draft to include FIP VN2VN VLAN notifications
and additional flags.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

libfc: sanity check cpu number extracted from xid

In the receive path libfc extracts a cpu number from the ox_id in the
fiber channel header and uses that to do a per_cpu_ptr conversion.  If,
for some reason, a frame is received with an invalid ox_id, per_cpu_ptr
will return an invalid pointer and the libfc receive path will panic the
system trying to use it.

I'm currently looking at such a case, and I don't yet know why a cpu
number > nr_cpu_ids is appearing in an exchange id.  But adding a sanity
check in libfc prevents a system panic, and seems like good idea when
dealing with frames coming in from the network.

Signed-off-by: Chris Leech <cleech@redhat.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fcoe: convert to kworker

The driver creates its own per-CPU threads which are updated based on
CPU hotplug events. It is also possible to use kworkers and remove some
of the kthread infrastrucure.

The code checked ->thread to decide if there is an active per-CPU
thread. By using the kworker infrastructure this is no longer
possible (or required). The thread pointer is saved in `kthread' instead
of `thread' so anything trying to use thread is caught by the
compiler. Currently only the bnx2fc driver is using struct fcoe_percpu_s
and the kthread member.

After a CPU went offline, we may still enqueue items on the "offline"
CPU. This isn't much of a problem. The work will be done on a random
CPU. The allocated crc_eof_page page won't be cleaned up. It is probably
expected that the CPU comes up at some point so it should not be a
problem. The crc_eof_page memory is released of course once the module
is removed.

This patch was only compile-tested due to -ENODEV.

Cc: Vasu Dev <vasu.dev@intel.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: fcoe-devel@open-fcoe.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

MAINTAINERS: Change FCoE maintainer

Vasu is going to resign from his maintainer role and I'll take over.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: Fix use-after-free in case of a dma mapping error

If there is a dma mapping error snic kfree()s buf right before printing
it.  Change the order to not accidently trip on memory that's not owned
by us anymore.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Narsimhulu Musini <nmusini@cisco.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: wd7000: print sector number as 64-bit

Enabling format checking in dprintk() shows that wd7000_biosparam uses
an incorrect format string for sector_t:

drivers/scsi/wd7000.c: In function 'wd7000_biosparam':
drivers/scsi/wd7000.c:1594:21: error: format '%d' expects argument of type 'int', but argument 3 has type 'sector_t {aka long long unsigned int}' [-Werror=format=]

As sector_t can be 32-bit wide, this adds a cast to 'u64' and prints
that with the correct format. The change to use no_printk() generally
helps with finding this kind of hidden format string bug, and I found
that when building with "-Wextra", which warned about an empty else
clause in

       } else
              dprintk("ok!\n");

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: libfc: fix seconds_since_last_reset calculation

The fc_get_host_stats() function contains a complex conversion from
jiffies to timespec to seconds. As we try to get rid of uses of struct
timespec, we can clean this up and replace it with a simpler
computation.

Simply dividing the difference in jiffies by HZ is not only much more
efficient, it also avoids a problem that causes the
seconds_since_last_reset value to be incorrect if jiffies has overrun
since the 'boot_time' value was recorded.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

53c700: Use proper debug printk format specifiers

When enabling the debug options NCR_700_DEBUG and NCR_700_TAG_DEBUG
various printk format warnings can be seen like:
drivers/scsi/53c700.c:357:2: warning: format  %p  expects argument of type  void * , but argument 4 has type  dma_addr_t  [-Wformat=]
  script_patch_32(hostdata->dev, script, MessageLocation,

Fix them by using the right printk format specifiers.

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

vmw_pvscsi: Change to update maintainer details (name, email)

[mkp: Updated MAINTAINERS]

Signed-off-by: Jim Gill <jgill@vmware.com>
Acked-by: Arvind Kumar <arvindkumar@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

cxlflash: Shutdown notify support for CXL Flash cards

Some CXL Flash cards need notification of device shutdown in order to
flush pending I/Os.

A PCI notification hook for shutdown has been added where the driver
notifies the card and returns. When the device is removed in the PCI
remove path, notification code will wait for shutdown processing to
complete.

Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

cxlflash: Add device dependent flags

Device dependent flags are needed to support functions that are specific
to a particular device.

One such case is - some CXL Flash cards need to be notified of device
shutdown. For other CXL devices, this feature does not prove to be
useful yet. Such distinct features need to be identified in the driver
to bypass or invoke specific functionality.

In this patch, a member 'flags' has been added to device dependent
values. These flags will be used and expanded in the future to support
various device specific functions.

Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

cxlflash: Fix to drain operations from previous reset

While running 'sg_reset -H' in a loop with a user-space application active,
hit the following exception:

cpu 0x2: Vector: 300 (Data Access)
    pc: : afu_attach+0x50/0x240 [cxlflash]
    lr: : cxlflash_afu_recover+0x3dc/0x7d0 [cxlflash]
    pid   = 20365, comm = run_block_fvt

Linux version 4.5.0-491-26f710d+

cxlflash_afu_recover+0x3dc/0x7d0 [cxlflash]
cxlflash_ioctl+0x5a8/0x6f0 [cxlflash]
scsi_ioctl+0x3b0/0x4c0
sd_ioctl+0x110/0x190
blkdev_ioctl+0x28c/0xc20
block_ioctl+0xa4/0xd0
do_vfs_ioctl+0xd8/0x8c0
SyS_ioctl+0xd4/0xf0
system_call+0x38/0xb4

The problem here is that the problem space area is unmapped while the
application issues the DK_CXLFLASH_RECOVER_AFU ioctl.

This is the order I observe:

proc1 proc2
1) sg_reset
2) ioctl(DK_CXLFLASH_RECOVER_AFU)
3) sg_reset again
   causing a PSA unmap
4) continues RECOVER_AFU processing

The resolution to this problem is to have the reset handler drain all
outstanding user space initiated ioctls before proceeding.  It is safe
to drain after the state has been changed to STATE_RESET. Also since
drain_ioctls() was static, it had to be moved up a bit to be before
cxlflash_eh_host_reset_handler().

Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

MAINTAINERS: Update email address for aacraid

Update the email address for aacraid from Adaptec to Microsemi.

Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_debug: fix sleep in invalid context

In this post: http://www.spinics.net/lists/linux-scsi/msg97124.html the
author shows some kernel infrastructure complaining about a sleep in an
invalid context. Remove offending call to vmalloc().  Instead of using
kzalloc() which reviewers didn't like, use a bucket system (64 bytes on
the stack) and potentially multiple calls to sg_pcopy_from_buffer() to
construct the 'data-in' buffer for the SCSI REPORT LUNS command.

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

libfc: Update rport reference counting

Originally libfc would just be initializing the refcount to '1', and
using the disc_mutex to synchronize if and when the final put should be
happening.  This has a race condition as the mutex might be delayed,
causing other threads to access an invalid structure.  This patch
updates the rport reference counting to increase the reference every
time 'rport_lookup' is called, and decreases the reference
correspondingly.  This removes the need to hold 'disc_mutex' when
removing the structure, and avoids the above race condition.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ultrastor.c depends on ISA_DMA_API

Fix build when CONFIG_ISA_DMA_API is not enabled. Fixes these build
errors (on x86_64):

../drivers/scsi/ultrastor.c: In function 'ultrastor_14f_detect':
../drivers/scsi/ultrastor.c:519:5: error: implicit declaration of function 'request_dma' [-Werror=implicit-function-declaration]
     if (config.dma_channel && request_dma(config.dma_channel,"Ultrastor")) {
     ^
../drivers/scsi/ultrastor.c: In function 'ultrastor_release':
../drivers/scsi/ultrastor.c:658:3: error: implicit declaration of function 'free_dma' [-Werror=implicit-function-declaration]
   free_dma(shost->dma_channel);
   ^

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2i: fix spelling mistake "complection" -> "completion"

Trivial fix to spelling mistake in printk message.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: update driver version to 1.5

Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: fix the inconsistent lock issue reported by CONFIG_PROVE_LOCKING

It is not necessary to surround call to
notify_port_event(, PORTE_BROADCAST_RCVD) by spin_lock_irqsave(),
so remove.
This was causing a warn, as below:

    =================================
    [ INFO: inconsistent lock state ]
    4.4.8+ #12 Not tainted
    ---------------------------------
    inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
    kworker/u64:1/168 [HC0[0]:SC0[0]:HE1:SE1] takes:
     (&(&hisi_hba->lock)->rlock){?.....}, at: [<ffffffc00052c708>] alloc_dev_quirk_v2_hw+0x48/0xec
    {IN-HARDIRQ-W} state was registered at:
      [<ffffffc0000fc764>] mark_lock+0x19c/0x6a0
      [<ffffffc0000fdc14>] __lock_acquire+0xa2c/0x1d00
      [<ffffffc0000ff654>] lock_acquire+0x58/0x7c
      [<ffffffc0008b609c>] _raw_spin_lock_irqsave+0x54/0x6c
      [<ffffffc00052d3c0>] int_chnl_int_v2_hw+0x1c4/0x248
      [<ffffffc0001098e8>] handle_irq_event_percpu+0x9c/0x144
      [<ffffffc0001099d4>] handle_irq_event+0x44/0x74
      [<ffffffc00010cd68>] handle_fasteoi_irq+0xb4/0x188
      [<ffffffc000108ea8>] generic_handle_irq+0x24/0x38
      [<ffffffc0001091fc>] __handle_domain_irq+0x60/0xac
      [<ffffffc00008261c>] gic_handle_irq+0xcc/0x168
      [<ffffffc0000855ac>] el1_irq+0x6c/0xe0
      [<ffffffc0000f7414>] default_idle_call+0x1c/0x34
      [<ffffffc0000f7654>] cpu_startup_entry+0x1d4/0x228
      [<ffffffc0008aecd8>] rest_init+0x150/0x160
      [<ffffffc000c4b95c>] start_kernel+0x3a4/0x3b8
      [<00000000008bb000>] 0x8bb000
    irq event stamp: 32661
    hardirqs last  enabled at (32661): [<ffffffc0008b41a8>] __mutex_unlock_slowpath+0x108/0x18c
    hardirqs last disabled at (32660): [<ffffffc0008b40e4>] __mutex_unlock_slowpath+0x44/0x18c
    softirqs last  enabled at (25114): [<ffffffc0000bde68>] __do_softirq+0x210/0x27c
    softirqs last disabled at (25095): [<ffffffc0000be224>] irq_exit+0x9c/0xe8

    other info that might help us debug this:
     Possible unsafe locking scenario:

           CPU0
           ----
      lock(&(&hisi_hba->lock)->rlock);
      <Interrupt>
        lock(&(&hisi_hba->lock)->rlock);

     *** DEADLOCK ***

    2 locks held by kworker/u64:1/168:
     #0:  ("%s"shost->work_q_name){++++.+}, at: [<ffffffc0000d2980>] process_one_work+0x134/0x3cc
     #1:  ((&sw->work)#2){+.+.+.}, at: [<ffffffc0000d2980>] process_one_work+0x134/0x3cc

    stack backtrace:
    CPU: 4 PID: 168 Comm: kworker/u64:1 Not tainted 4.4.8+ #12
    Hardware name: Huawei Technologies Co., Ltd. D03/D03, BIOS 1.12 01/01/1900
    Workqueue: scsi_wq_1 sas_discover_domain
    Call trace:
    [<ffffffc000089988>] dump_backtrace+0x0/0x114
    [<ffffffc000089ab0>] show_stack+0x14/0x1c
    [<ffffffc00035ac50>] dump_stack+0xb4/0xf0
    [<ffffffc0000fc524>] print_usage_bug+0x210/0x2b4
    [<ffffffc0000fcbc4>] mark_lock+0x5fc/0x6a0
    [<ffffffc0000fd9e8>] __lock_acquire+0x800/0x1d00
    [<ffffffc0000ff654>] lock_acquire+0x58/0x7c
    [<ffffffc0008b5edc>] _raw_spin_lock+0x44/0x58
    [<ffffffc00052c708>] alloc_dev_quirk_v2_hw+0x48/0xec
    [<ffffffc000528214>] hisi_sas_dev_found+0x48/0x1b8
    [<ffffffc00051a9b8>] sas_notify_lldd_dev_found+0x34/0xe0
    [<ffffffc00051e5e8>] sas_discover_root_expander+0x58/0x128
    [<ffffffc00051b38c>] sas_discover_domain+0x4bc/0x564
    [<ffffffc0000d29ec>] process_one_work+0x1a0/0x3cc
    [<ffffffc0000d2d50>] worker_thread+0x138/0x438
    [<ffffffc0000d9494>] kthread+0xdc/0xf0
    [<ffffffc000085c50>] ret_from_fork+0x10/0x40

Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

hisi_sas: add v2 hw ACPI support

Add support in v2 hw driver for ACPI.

A check on whether an ACPI handle is available for the device is used to
decide on whether to use ACPI reset handler or syscon for hw reset.

Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: storvsc: Filter out storvsc messages CD-ROM medium not present

When a virtual scsi DVD device is present with no image file
attached the storvsc driver logs all resulting unnecessary sense errors
whenever IO is issued to the device.

[storvsc] Sense Key : Not Ready [current]
[storvsc] Add. Sense: Medium not present - tray closed

[mkp: Fixed whitespace]

Signed-off-by: Cathy Avery <cavery@redhat.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

bnx2fc: replace printk() with BNX2FC_IO_DBG()

The "fcp_rsp_code = %d" message isn't an error, it's meant to be
informative only.  This patch prevents a flood of such messages in some
situations.

Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: avoid mpt3sas_transport_port_add NULL parent_dev

If _scsih_sas_host_add's call to mpt3sas_config_get_sas_iounit_pg0
fails, ioc->sas_hba.parent_dev may be left uninitialized.  A later
device probe could invoke mpt3sas_transport_port_add which will call
sas_port_alloc_num [scsi_transport_sas] with a NULL parent_dev pointer.

Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mpt3sas: set num_phys after allocating phy[] space

In _scsih_sas_host_add, the number of HBA phys are determined and then
later used to allocate an array of struct _sas_phy's.  If the routine
sets ioc->sas_hba.num_phys, but then fails to allocate the
ioc->sas_hba.phy array (by kcalloc error or other intermediate
error/exit path), ioc->sas_hba is left in a dangerous state: all readers
of ioc->sas_hba.phy[] do so by indexing it from 0..ioc->sas_hba.num_phys
without checking that the space was ever allocated.

Modify _scsih_sas_host_add to set ioc->sas_hba.num_phys only after
successfully allocating ioc->sas_hba.phy[].

Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: Adding license info do tc-dwc-g210 and ufshcd-dwc to enable loadable module

This patch adds license info to the tc-dwc-g210 and ufshcd-dwc files in
order for them to have access to some ufshcd symbols when all are built
as modules.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

MAINTAINERS: Add file patterns for scsi device tree bindings

Submitters of device tree binding documentation may forget to CC the
subsystem maintainer if this is missing.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aacraid: use kmemdup

Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.

Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

pm8001: fix typo

firmare -> firmware

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

snic: fix typo

firmare -> firmware

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add TC G210 pci driver

This patch adds a glue pci driver for the Synopsys G210 Test Chip.

[mkp: Fixed Kconfig depends and module name]

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add TC G210 platform driver

This patch adds a glue platform driver for the Synopsys G210 Test Chip.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add support for Synopsys G210 Test Chip

This patch adds support for Synopsys G210 Test Chip.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add support for DesignWare Controller

This patch has the goal to add support for DesignWare UFS Controller
specific operations.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add link status to ufshci

Add link status to ufshci.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add unipro attributes

Add unipro attributes.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add UFS 2.0 capabilities

Add UFS 2.0 support to the UFS core driver.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: add UFS 2.0 to ufshcd-pltfrm bindings

Add UFS 2.0 to the ufshcd-pltfrm devicetree binding.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ufs: fixed typo in ufshcd-pltfrm

Fixed typo in ufshcd-pltfrm.

Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Merge tag 'qcom-smd-list-voltage' of git://git./linux/kernel/git/broonie/regulator

Pull regulator fix from Mark Brown:
 "Fix qcom-smd list voltage issues for msm8974

  This commit looks like a cleanup but in fact by causing the core to go
  down some simplified code paths for noop regulators it avoids a boot
  time crash for msm8974 platforms which was introduced in v4.7.  It has
  been in -next for a while, the issues in mainline for these platforms
  weren't flagged up to me until yesterday (I think it took some time to
  figure out what was going wrong)"

* tag 'qcom-smd-list-voltage' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: qcom_smd: Remove list_voltage callback for rpm_smps_ldo_ops_fixed

Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  posix_acl: de-union a_refcount and a_rcu
  nfs_atomic_open(): prevent parallel nfs_lookup() on a negative hashed
  Use the right predicate in ->atomic_open() instances

posix_acl: de-union a_refcount and a_rcu

Currently the two are unioned together, but I don't think that's safe.

It looks like get_cached_acl could race with the last put in
posix_acl_release. get_cached_acl calls atomic_inc_not_zero on
a_refcount, but that field could have already been clobbered by
call_rcu, and may no longer be zero. Fix this by de-unioning the two
fields.

Fixes: b8a7a3a66747 (posix_acl: Inode acl caching fixes)
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Linux 4.7-rc7

tmpfs: fix regression hang in fallocate undo

The well-spotted fallocate undo fix is good in most cases, but not when
fallocate failed on the very first page.  index 0 then passes lend -1
to shmem_undo_range(), and that has two bad effects: (a) that it will
undo every fallocation throughout the file, unrestricted by the current
range; but more importantly (b) it can cause the undo to hang, because
lend -1 is treated as truncation, which makes it keep on retrying until
every page has gone, but those already fully instantiated will never go
away.  Big thank you to xfstests generic/269 which demonstrates this.

Fixes: b9b4bb26af01 ("tmpfs: don't undo fallocate past its last page")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus

Pull MIPS fix from Ralf Baechle:
 "Another week with just a single 4.7 fix.

  This fixes a possible 'loss' of the huge page bit from pmd on
  permission change"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix page table corruption on THP permission changes.

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
 "Three fixes.  One is the qla24xx MSI regression, one is a theoretical
  problem over blacklist matching, which would bite USB badly if it ever
  triggered and one is a system hang with a particular type of IPR
  device"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  qla2xxx: Fix NULL pointer deref in QLA interrupt
  SCSI: fix new bug in scsi_dev_info_list string matching
  ipr: Clear interrupt on croc/crocodile when running with LSI

Merge tag 'ecryptfs-4.7-rc7-fixes' of git://git./linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Provide a more concise fix for CVE-2016-1583:
   - Additionally fixes linux-stable regressions caused by the
     cherry-picking of the original fix

  Some very minor changes that have queued up:
   - Fix typos in code comments
   - Remove unnecessary check for NULL before destroying kmem_cache"

* tag 'ecryptfs-4.7-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  ecryptfs: don't allow mmap when the lower fs doesn't support it
  Revert "ecryptfs: forbid opening files without mmap handler"
  ecryptfs: fix spelling mistakes
  eCryptfs: fix typos in comment
  ecryptfs: drop null test before destroy functions

Merge tag 'iommu-fixes-v4.7-rc6' of git://git./linux/kernel/git/joro/iommu

Pull IOMMU fixes from Joerg Roedel:
 "Two Fixes:

   - Intel VT-d fix for a suspend/resume issue, introduced with the
     scalability improvements in this cycle.

   - AMD IOMMU fix for systems that have unity mappings defined.  There
     was a race where translation got enabled before the unity mappings
     were in place.  This issue was seen on some HP servers"

* tag 'iommu-fixes-v4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Fix unity mapping initialization race
  iommu/vt-d: Fix infinite loop in free_all_cpu_cached_iovas

Merge tag 'for-linus-4.7b-rc6-tag' of git://git./linux/kernel/git/xen/tip

Pull xen bug fixes from David Vrabel:

 - Fix two bugs in the handling of xenbus transactions.

 - Make the xen acpi driver compatible with Xen 4.7.

* tag 'for-linus-4.7b-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/acpi: allow xen-acpi-processor driver to load on Xen 4.7
  xenbus: simplify xenbus_dev_request_and_reply()
  xenbus: don't bail early from xenbus_dev_request_and_reply()
  xenbus: don't BUG() on user mode induced condition

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Will Deacon:
 "A couple of late fixes here, but one that we've been sitting on for a
  few weeks while the details were worked out.  Specifically, we now
  enforce USER_DS on taking exceptions whilst in the kernel, which
  avoids leaking kernel data to userspace through things like perf.  The
  other patch is an update to a workaround for a hardware erratum on
  some Cavium SoCs.

  Summary:

   - Enforce USER_DS on exception entry from EL1

   - Apply workaround for Cavium errata #27456 on Thunderx-81xx parts"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Enable workaround for Cavium erratum 27456 on thunderx-81xx
  arm64: kernel: Save and restore UAO and addr_limit on exception entry

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Ingo Molnar:
 "Three fixes:

   - A boot crash fix with certain configs
   - a MAINTAINERS entry update
   - Documentation typo fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/Documentation: Fix various typos in Documentation/x86/ files
  x86/amd_nb: Fix boot crash on non-AMD systems
  MAINTAINERS: Update the Calgary IOMMU entry

Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Ingo Molnar:
 "Two load-balancing fixes for cgroups-intense workloads"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix calc_cfs_shares() fixed point arithmetics width confusion
  sched/fair: Fix effective_load() to consistently use smoothed load

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Ingo Molnar:
 "Various fixes:

   - 32-bit callgraph bug fix
   - suboptimal event group scheduling bug fix
   - event constraint fixes for Broadwell/Skylake
   - RAPL module name collision fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix pmu::filter_match for SW-led groups
  x86/perf/intel/rapl: Fix module name collision with powercap intel-rapl
  perf/x86: Fix 32-bit perf user callgraph collection
  perf/x86/intel: Update event constraints when HT is off

Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull irq fixes from Ingo Molnar:
 "Two MIPS-GIC irqchip driver fixes to unbreak certain MIPS boards"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/mips-gic: Match IPI IRQ domain by bus token only
  irqchip/mips-gic: Map to VPs using HW VPNum

Merge tag 'gpio-v4.7-5' of git://git./linux/kernel/git/linusw/linux-gpio

Pull GPIO fixes from Linus Walleij:
 "I don't like to toss in last minute patches, but these are all for
  things that are broken, and have bitten people for real.  Two of them
  go into stable.  Maybe all of them if the compile test problem is a
  pain in the ass also for stable folks.

  Final (hopefully) GPIO fixes for v4.7:

   - Fix an oops on the Asus Eee PC 1201

   - Revert a patch trying to split GPIO parsing and GPIO configuration

   - Revert a too liberal compile testing thing"

* tag 'gpio-v4.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  Revert "gpio: gpiolib-of: Allow compile testing"
  Revert "gpiolib: Split GPIO flags parsing and GPIO configuration"
  gpio: sch: Fix Oops on module load on Asus Eee PC 1201

Merge tag 'drm-fixes-for-v4.7-rc7' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
 "One nouveau fix, and a few AMD Polaris fixes and some Allwinner fixes.

  I've got some vmware fixes that I might send separate over the
  weekend, they fix some black screens, but I'm still debating them"

* tag 'drm-fixes-for-v4.7-rc7' of git://people.freedesktop.org/~airlied/linux:
  drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation.
  drm/amd/powerplay: fix bug that get wrong polaris evv voltage.
  drm/amd/powerplay: incorrectly use of the function return value
  drm/amd/powerplay: fix incorrect voltage table value for tonga
  drm/amd/powerplay: fix incorrect voltage table value for polaris10
  drm/nouveau/disp/sor/gf119: select correct sor when poking training pattern
  gpu: drm: sun4i_drv: add missing of_node_put after calling of_parse_phandle
  drm/sun4i: Send vblank event when the CRTC is disabled
  drm/sun4i: Report proper vblank

ecryptfs: don't allow mmap when the lower fs doesn't support it

There are legitimate reasons to disallow mmap on certain files, notably
in sysfs or procfs.  We shouldn't emulate mmap support on file systems
that don't offer support natively.

CVE-2016-1583

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: stable@vger.kernel.org
[tyhicks: clean up f_op check by using ecryptfs_file_to_lower()]
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>

xen/acpi: allow xen-acpi-processor driver to load on Xen 4.7

As of Xen 4.7 PV CPUID doesn't expose either of CPUID[1].ECX[7] and
CPUID[0x80000007].EDX[7] anymore, causing the driver to fail to load on
both Intel and AMD systems. Doing any kind of hardware capability
checks in the driver as a prerequisite was wrong anyway: With the
hypervisor being in charge, all such checking should be done by it. If
ACPI data gets uploaded despite some missing capability, the hypervisor
is free to ignore part or all of that data.

Ditch the entire check_prereq() function, and do the only valid check
(xen_initial_domain()) in the caller in its place.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

xenbus: simplify xenbus_dev_request_and_reply()

No need to retain a local copy of the full request message, only the
type is really needed.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

xenbus: don't bail early from xenbus_dev_request_and_reply()

xenbus_dev_request_and_reply() needs to track whether a transaction is
open.  For XS_TRANSACTION_START messages it calls transaction_start()
and for XS_TRANSACTION_END messages it calls transaction_end().

If sending an XS_TRANSACTION_START message fails or responds with an
an error, the transaction is not open and transaction_end() must be
called.

If sending an XS_TRANSACTION_END message fails, the transaction is
still open, but if an error response is returned the transaction is
closed.

Commit 027bd7e89906 ("xen/xenbus: Avoid synchronous wait on XenBus
stalling shutdown/restart") introduced a regression where failed
XS_TRANSACTION_START messages were leaving the transaction open.  This
can cause problems with suspend (and migration) as all transactions
must be closed before suspending.

It appears that the problematic change was added accidentally, so just
remove it.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security

Pull apparmor fix from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  apparmor: fix oops, validate buffer size in apparmor_setprocattr()

Merge tag 'acpi-4.7-rc7' of git://git./linux/kernel/git/rafael/linux-pm

Pull ACPI fixes from Rafael Wysocki:
 "All of these fix recent regressions in ACPICA, in the ACPI PCI IRQ
  management code and in the ACPI AML debugger.

  Specifics:

   - Fix a lock ordering issue in ACPICA introduced by a recent commit
     that attempted to fix a deadlock in the dynamic table loading code
     which in turn appeared after changes related to the handling of
     module-level AML also made in this cycle (Lv Zheng).

   - Fix a recent regression in the ACPI IRQ management code that may
     cause PCI drivers to be unable to register an IRQ if that IRQ
     happens to be shared with a device on the ISA bus, like the
     parallel port, by reverting one commit entirely and restoring the
     previous behavior in two other places (Sinan Kaya).

   - Fix a recent regression in the ACPI AML debugger introduced by the
     commit that removed incorrect usage of IS_ERR_VALUE() from multiple
     places (Lv Zheng)"

* tag 'acpi-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / debugger: Fix regression introduced by IS_ERR_VALUE() removal
  ACPICA: Namespace: Fix namespace/interpreter lock ordering
  ACPI,PCI,IRQ: separate ISA penalty calculation
  Revert "ACPI, PCI, IRQ: remove redundant code in acpi_irq_penalty_init()"
  ACPI,PCI,IRQ: factor in PCI possible

Merge tag 'pm-4.7-rc7' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fixes from Rafael Wysocki:
 "One fix for a recent cpuidle core change that, against all odds,
  introduced a functional regression on Power systems and the fix for
  the crash during resume from hibernation on x86-64 that has been in
  the works for the last few weeks (it actually was ready last week, but
  I wanted to allow the reporters to test if for some more time).

  Specifics:

   - Fix a recent performance regression on Power systems (powernv and
     pseries) introduced by a core cpuidle commit that decreased the
     precision of the last_residency conversion from nano- to
     microseconds, which should not matter in theory, but turned out to
     play not-so-well with the special "snooze" idle state on Power
     (Shreyas B Prabhu).

   - Fix a crash during resume from hibernation on x86-64 caused by
     possible corruption of the kernel text part of page tables in the
     last phase of image restoration exposed by a security-related
     change during the 4.3 development cycle (Rafael Wysocki)"

* tag 'pm-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: Fix last_residency division
  x86/power/64: Fix kernel text mapping corruption during image restoration