Marek Vasut [Mon, 24 Mar 2014 02:38:10 +0000 (03:38 +0100)]
gpio: mxs: Allow for recursive enable_irq_wake() call
The scenario here is that someone calls enable_irq_wake() from somewhere
in the code. This will result in the lockdep producing a backtrace as can
be seen below. In my case, this problem is triggered when using the wl1271
(TI WlCore) driver found in drivers/net/wireless/ti/ .
The problem cause is rather obvious from the backtrace, but let's outline
the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(),
which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq()
calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to
grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in
irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not
marked as recursive, lockdep will spew the stuff below.
We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to
fix the spew.
=============================================
[ INFO: possible recursive locking detected ]
3.10.33-00012-gf06b763-dirty #61 Not tainted
---------------------------------------------
kworker/0:1/18 is trying to acquire lock:
(&irq_desc_lock_class){-.-...}, at: [<
c00685f0>] __irq_get_desc_lock+0x48/0x88
but task is already holding lock:
(&irq_desc_lock_class){-.-...}, at: [<
c00685f0>] __irq_get_desc_lock+0x48/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&irq_desc_lock_class);
lock(&irq_desc_lock_class);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by kworker/0:1/18:
#0: (events){.+.+.+}, at: [<
c0036308>] process_one_work+0x134/0x4a4
#1: ((&fw_work->work)){+.+.+.}, at: [<
c0036308>] process_one_work+0x134/0x4a4
#2: (&irq_desc_lock_class){-.-...}, at: [<
c00685f0>] __irq_get_desc_lock+0x48/0x88
stack backtrace:
CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted
3.10.33-00012-gf06b763-dirty #61
Workqueue: events request_firmware_work_func
[<
c0013eb4>] (unwind_backtrace+0x0/0xf0) from [<
c0011c74>] (show_stack+0x10/0x14)
[<
c0011c74>] (show_stack+0x10/0x14) from [<
c005bb08>] (__lock_acquire+0x140c/0x1a64)
[<
c005bb08>] (__lock_acquire+0x140c/0x1a64) from [<
c005c6a8>] (lock_acquire+0x9c/0x104)
[<
c005c6a8>] (lock_acquire+0x9c/0x104) from [<
c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58)
[<
c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) from [<
c00685f0>] (__irq_get_desc_lock+0x48/0x88)
[<
c00685f0>] (__irq_get_desc_lock+0x48/0x88) from [<
c0068e78>] (irq_set_irq_wake+0x20/0xf4)
[<
c0068e78>] (irq_set_irq_wake+0x20/0xf4) from [<
c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24)
[<
c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) from [<
c0068cf4>] (set_irq_wake_real+0x30/0x44)
[<
c0068cf4>] (set_irq_wake_real+0x30/0x44) from [<
c0068ee4>] (irq_set_irq_wake+0x8c/0xf4)
[<
c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) from [<
c0310748>] (wlcore_nvs_cb+0x10c/0x97c)
[<
c0310748>] (wlcore_nvs_cb+0x10c/0x97c) from [<
c02be5e8>] (request_firmware_work_func+0x38/0x58)
[<
c02be5e8>] (request_firmware_work_func+0x38/0x58) from [<
c0036394>] (process_one_work+0x1c0/0x4a4)
[<
c0036394>] (process_one_work+0x1c0/0x4a4) from [<
c0036a4c>] (worker_thread+0x138/0x394)
[<
c0036a4c>] (worker_thread+0x138/0x394) from [<
c003cb74>] (kthread+0xa4/0xb0)
[<
c003cb74>] (kthread+0xa4/0xb0) from [<
c000ee00>] (ret_from_fork+0x14/0x34)
wlcore: loaded
Cc: stable@vger.kernel.org
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alexander Shiyan [Sat, 22 Mar 2014 08:35:22 +0000 (12:35 +0400)]
gpio: samsung: Add missing "break" statement
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alexander Shiyan [Sat, 22 Mar 2014 08:32:15 +0000 (12:32 +0400)]
gpio: twl4030: Remove redundant assignment
Variable "status" is never used, so remove it and add warning if
any error happen.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sebastian Andrzej Siewior [Sat, 22 Mar 2014 16:16:39 +0000 (17:16 +0100)]
gpio: dwapb: correct gpio-cells in binding document
The example uses gpio-cells = 1 while it should be two (it is even
mentioned in the text above).
Cc: devicetree@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bartlomiej Zolnierkiewicz [Tue, 18 Mar 2014 09:58:33 +0000 (10:58 +0100)]
gpio: iop: fix devm_ioremap_resource() return value checking
devm_ioremap_resource() returns a pointer to the remapped memory or
an ERR_PTR() encoded error code on failure. Fix the check inside
iop3xx_gpio_probe() accordingly.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 25 Mar 2014 12:37:17 +0000 (13:37 +0100)]
pinctrl: coh901: convert driver to use gpiolib irqchip
This converts the COH901 pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 25 Mar 2014 09:44:09 +0000 (10:44 +0100)]
pinctrl: nomadik: convert driver to use gpiolib irqchip
This converts the Nomadik pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 25 Mar 2014 09:42:35 +0000 (10:42 +0100)]
gpio: pl061: convert driver to use gpiolib irqchip
This converts the PL061 driver to register its chained irq
handler and irqchip using the helpers in the gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 25 Mar 2014 09:40:18 +0000 (10:40 +0100)]
gpio: add IRQ chip helpers in gpiolib
This provides a function gpiochip_irqchip_add() to set
up an irqchip for a GPIO controller, and a function
gpiochip_set_chained_irqchip() to chain it to a parent
irqchip.
Most GPIOs are of the type where a number of lines form
a cascaded interrupt controller chained onto
the primary system interrupt controller (or further down the
chain) so let's add this helper and factor the code to
request the lines to be used as IRQs, the .to_irq() function
and the irqdomain into the core as well.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 21 Mar 2014 09:40:24 +0000 (10:40 +0100)]
pinctrl: nomadik: factor in platform data container
The old platform data struct is just a leftover from the times
when the driver was not probed exclusively from the device tree.
Factor this into the general state container and simplify the
probe path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 21 Mar 2014 09:24:42 +0000 (10:24 +0100)]
pinctrl: nomadik: rename secondary to latent
The "secondary irq" in the nomadik pin control driver is actually
not secondary (as in: can occur any time alongside the ordinary
irq), it is a latent IRQ. It is an IRQ that has occurred when
the system was in sleep state and has been cached in a special
register flagged from the low power management unit (PRCM).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alexander Shiyan [Tue, 11 Mar 2014 17:55:14 +0000 (21:55 +0400)]
gpio: Driver for SYSCON-based GPIOs
SYSCON driver was designed for using memory areas (registers)
that are used in several subsystems. There are systems (CPUs)
which use bits in one register for various purposes and thus
should be handled by various kernel subsystems. This driver
allows you to use the individual SYSCON bits as GPIOs.
ARM CLPS711X SYSFLG1 input lines has been added as first user
of this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alexander Shiyan [Sun, 16 Mar 2014 05:10:34 +0000 (09:10 +0400)]
gpio: generic: Use platform_device_id->driver_data field for driver flags
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 14 Mar 2014 17:24:30 +0000 (18:24 +0100)]
pinctrl: coh901: move irq line locking to resource callbacks
This switches the COH901 GPIO driver over to using the
.request_resources() and .release_resources() callbacks from
the irqchip vtable and separate the calls from the .enable()
and .disable() callbacks as the latter cannot really say no
to a request, whereas the resource callbacks can.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 14 Mar 2014 17:16:20 +0000 (18:16 +0100)]
gpio: switch drivers to use new callback
This switches all GPIO and pin control drivers with irqchips
that were using .startup() and .shutdown() callbacks to lock
GPIO lines for IRQ usage over to using the .request_resources()
and .release_resources() callbacks just introduced into the
irqchip vtable.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alan Tull [Fri, 14 Mar 2014 16:08:54 +0000 (11:08 -0500)]
gpio: gpio-dwapb size-cells should be two
Fix size-cells to show use of OF_GPIO_ACTIVE_LOW flag.
Signed-off-by: Alan Tull <atull@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Fri, 14 Mar 2014 15:58:07 +0000 (17:58 +0200)]
gpio / ACPI: Add support for ACPI GPIO operation regions
GPIO operation regions is a new feature introduced in ACPI 5.0
specification. This feature adds a way for platform ASL code to call back
to OS GPIO driver and toggle GPIO pins.
An example ASL code from Lenovo Miix 2 tablet with only relevant part
listed:
Device (\_SB.GPO0)
{
Name (AVBL, Zero)
Method (_REG, 2, NotSerialized)
{
If (LEqual (Arg0, 0x08))
{
// Marks the region available
Store (Arg1, AVBL)
}
}
OperationRegion (GPOP, GeneralPurposeIo, Zero, 0x0C)
Field (GPOP, ByteAcc, NoLock, Preserve)
{
Connection (
GpioIo (Exclusive, PullDefault, 0, 0, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer,,)
{
0x003B
}
),
SHD3, 1,
}
}
Device (SHUB)
{
Method (_PS0, 0, Serialized)
{
If (LEqual (\_SB.GPO0.AVBL, One))
{
Store (One, \_SB.GPO0.SHD3)
Sleep (0x32)
}
}
Method (_PS3, 0, Serialized)
{
If (LEqual (\_SB.GPO0.AVBL, One))
{
Store (Zero, \_SB.GPO0.SHD3)
}
}
}
How this works is that whenever _PS0 or _PS3 method is run (typically when
SHUB device is transitioned to D0 or D3 respectively), ASL code checks if
the GPIO operation region is available (\_SB.GPO0.AVBL). If it is we go and
store either 0 or 1 to \_SB.GPO0.SHD3.
Now, when ACPICA notices ACPI GPIO operation region access (the store
above) it will call acpi_gpio_adr_space_handler() that then toggles the
GPIO accordingly using standard gpiolib interfaces.
Implement the support by registering GPIO operation region handlers for all
GPIO devices that have an ACPI handle. First time the GPIO is used by the
ASL code we make sure that the GPIO stays requested until the GPIO chip
driver itself is unloaded. If we find out that the GPIO is already
requested we just toggle it according to the value got from ASL code.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 14 Mar 2014 09:26:56 +0000 (10:26 +0100)]
Merge branch 'irq/for-gpio' of git://git./linux/kernel/git/tip/tip into devel
Linus Walleij [Fri, 14 Mar 2014 09:26:45 +0000 (10:26 +0100)]
Merge tag 'v3.14-rc6' into devel
Linux 3.14-rc6
Alexandre Courbot [Tue, 11 Mar 2014 06:52:09 +0000 (15:52 +0900)]
gpio: clamp returned values to the boolean range
Nothing prevents GPIO drivers from returning values outside the
boolean range, and as it turns out a few drivers are actually doing so.
These values were passed as-is to unsuspecting consumers and created
confusion.
This patch makes the internal _gpiod_get_raw_value() function return a
bool, effectively clamping the GPIO value to the boolean range no
matter what the driver does.
While we are at it, we also change the value parameter of
_gpiod_set_raw_value() to bool type before drivers start doing funny
things with it as well.
Another way to fix this would be to change the prototypes of the driver
interface to use bool directly, but this would require a huge
cross-systems patch so this simpler solution is preferred.
Changes since v1:
- Change local variable type to bool as well, use boolean values in
code
- Also change prototype of open drain/open source setting functions
since they are only called from _gpiod_set_raw_value()
This probably calls for a larger booleanization of gpiolib, but let's
keep that for a latter change - right now we need to address the issue
of non-boolean values returned by drivers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Mon, 10 Mar 2014 12:54:53 +0000 (14:54 +0200)]
gpio / ACPI: Rework ACPI GPIO event handling
The current ACPI GPIO event handling code was never tested against real
hardware with functioning GPIO triggered events (at the time such hardware
wasn't available). Thus it misses certain things like requesting the GPIOs
properly, passing correct flags to the interrupt handler and so on.
This patch reworks ACPI GPIO event handling so that we:
1) Use struct acpi_gpio_event for all GPIO signaled events.
2) Switch to use GPIO descriptor API and request GPIOs by calling
gpiochip_request_own_desc() that we added in a previous patch.
3) Pass proper flags from ACPI GPIO resource to request_threaded_irq().
Also instead of open-coding the _AEI iteration loop we can use
acpi_walk_resources(). This simplifies the code a bit and fixes memory leak
that was caused by missing kfree() for buffer returned by
acpi_get_event_resources().
Since the remove path now calls gpiochip_free_own_desc() which takes GPIO
spinlock we need to call acpi_gpiochip_remove() outside of that lock
(analogous to acpi_gpiochip_add() path where the lock is released before
those funtions are called).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Mon, 10 Mar 2014 12:54:52 +0000 (14:54 +0200)]
gpio / ACPI: Rename acpi_gpio_evt_pin to acpi_gpio_event
In order to consolidate _Exx, _Lxx and _EVT to use the same structure make
the structure name to reflect that we are dealing with any event, not just
_EVT.
This is just rename, no functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Mon, 10 Mar 2014 12:54:51 +0000 (14:54 +0200)]
gpio / ACPI: Allocate ACPI specific data directly in acpi_gpiochip_add()
We are going to add more ACPI specific data to accompany GPIO chip so
instead of allocating it per each use-case we allocate it once when
acpi_gpiochip_add() is called and release it when acpi_gpiochip_remove() is
called.
Doing this allows us to add more ACPI specific data by merely adding new
fields to struct acpi_gpio_chip.
In addition we embed evt_pins member directly to the structure instead of
having it as a pointer. This simplifies the code a bit since we don't need
to check against NULL.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Mon, 10 Mar 2014 12:54:50 +0000 (14:54 +0200)]
gpiolib: Allow GPIO chips to request their own GPIOs
Sometimes it is useful to allow GPIO chips themselves to request GPIOs they
own through gpiolib API. One use case is ACPI ASL code that should be able
to toggle GPIOs through GPIO operation regions.
We can't use gpio_request() because it will pin the module to the kernel
forever (it calls try_module_get()). To solve this we move module refcount
manipulation to gpiod_request() and let __gpiod_request() handle the actual
request. This changes the sequence a bit as now try_module_get() is called
outside of gpio_lock (I think this is safe, try_module_get() handles
serialization it needs already).
Then we provide gpiolib internal functions gpiochip_request/free_own_desc()
that do the same as gpio_request() but don't manipulate module refrence
count. This allows the GPIO chip driver to request and free descriptors it
owns without being pinned to the kernel forever.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Thomas Gleixner [Sat, 8 Mar 2014 07:59:58 +0000 (08:59 +0100)]
genirq: Provide irq_request/release_resources chip callbacks
For certain irq types, e.g. gpios, it's necessary to request resources
before starting up the irq.
This might fail so we cannot use the irq_startup() callback because we
might call the irq_set_type() callback before that which does not make
sense when the resource is not available. Calling irq_startup() before
irq_set_type() can lead to spurious interrupts which is not desired
either.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1403080857160.18573@ionos.tec.linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Markus Mayer [Wed, 12 Feb 2014 23:42:27 +0000 (15:42 -0800)]
MAINTAINERS: Add Broadcom GPIO maintainer
List myself as maintainer for Broadcom's Kona GPIO driver.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Geert Uytterhoeven [Tue, 11 Mar 2014 10:23:44 +0000 (11:23 +0100)]
gpio: Spelling s/than/that/
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jean Delvare [Fri, 7 Mar 2014 21:11:37 +0000 (22:11 +0100)]
gpio: cs5535: Simplify dependencies
The bus and architecture dependencies are already on MFD_CS5535, so
there is no need to repeat them here.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gary Servin [Thu, 6 Mar 2014 23:25:26 +0000 (20:25 -0300)]
gpio: mcp23s08: trivial: fixed coding style issues
This coding style issue was detected using the checkpatch.pl script
Signed-off-by: Gary Servin <garyservin@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Krzysztof Kozlowski [Thu, 6 Mar 2014 09:31:16 +0000 (10:31 +0100)]
gpio: max732x: Fix possible NULL pointer dereference on i2c_new_dummy error
In max732x_probe() driver allocates dummy I2C device (if number of ports
is greater than 8) with i2c_new_dummy() but it does not check the return
value of this call.
In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later
dereferenced by i2c_smbus_read_byte() (called from max732x_readb()).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Krzysztof Kozlowski [Thu, 6 Mar 2014 09:31:15 +0000 (10:31 +0100)]
gpio: max732x: Fix I2C dummy device resource leak on probe failure
In max732x_probe() driver allocates dummy I2C device (if number of ports
is greater than 8) however it is not unregistered if probe fails later.
Fix the leak by unregistering dummy I2C device if it was allocated.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lad, Prabhakar [Thu, 6 Mar 2014 05:58:25 +0000 (11:28 +0530)]
devicetree: bindings: gpio-davinic: fix documentation
This patch adds missing #gpio-cells and also adds a
usage example for leds.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alexander Holler [Wed, 5 Mar 2014 11:21:01 +0000 (12:21 +0100)]
gpio: davinci: fix gpio selection for OF
The driver missed an of_xlate function to translate gpio numbers
as found in the DT to the correct chip and number.
While there I've set #gpio_cells to a fixed value of 2.
I've used gpio-pxa.c as template for those changes and tested my changes
successfully on a da850 board using entries for gpio-leds in a DT. So I didn't
reinvent the wheel but just copied and tested stuff.
Thanks to Grygorii Strashko for the hint to the existing code in gpio-pxa.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Mon, 10 Mar 2014 02:41:57 +0000 (19:41 -0700)]
Linux 3.14-rc6
Linus Torvalds [Mon, 10 Mar 2014 02:27:31 +0000 (19:27 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Linus Torvalds [Mon, 10 Mar 2014 02:17:39 +0000 (19:17 -0700)]
Merge tag 'nfs-for-3.14-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- Fix another nfs4_sequence corruptor in RELEASE_LOCKOWNER
- Fix an Oopsable delegation callback race
- Fix another bad stateid infinite loop
- Fail the data server I/O is the stateid represents a lost lock
- Fix an Oopsable sunrpc trace event"
* tag 'nfs-for-3.14-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Fix oops when trace sunrpc_task events in nfs client
NFSv4: Fail the truncate() if the lock/open stateid is invalid
NFSv4.1 Fail data server I/O if stateid represents a lost lock
NFSv4: Fix the return value of nfs4_select_rw_stateid
NFSv4: nfs4_stateid_is_current should return 'true' for an invalid stateid
NFS: Fix a delegation callback race
NFSv4: Fix another nfs4_sequence corruptor
Linus Torvalds [Mon, 10 Mar 2014 01:59:14 +0000 (18:59 -0700)]
Merge tag 'usb-3.14-rc6' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 4 USB fixes for your current tree.
Two of them are reverts to hopefully resolve the nasty XHCI
regressions we have been having on some types of devices. The other
two are quirks for some Logitech video devices"
* tag 'usb-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
Linus Torvalds [Mon, 10 Mar 2014 01:58:27 +0000 (18:58 -0700)]
Merge tag 'staging-3.15-rc6' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver tree fix from Greg KH:
"Here is a single staging driver fix for your tree.
It resolves an issue with arbritary writes to memory if a specific
driver is loaded"
* tag 'staging-3.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging/cxt1e1/linux.c: Correct arbitrary memory write in c4_ioctl()
David Howells [Sun, 9 Mar 2014 08:21:58 +0000 (08:21 +0000)]
KEYS: Make the keyring cycle detector ignore other keyrings of the same name
This fixes CVE-2014-0102.
The following command sequence produces an oops:
keyctl new_session
i=`keyctl newring _ses @s`
keyctl link @s $i
The problem is that search_nested_keyrings() sees two keyrings that have
matching type and description, so keyring_compare_object() returns true.
s_n_k() then passes the key to the iterator function -
keyring_detect_cycle_iterator() - which *should* check to see whether this is
the keyring of interest, not just one with the same name.
Because assoc_array_find() will return one and only one match, I assumed that
the iterator function would only see an exact match or never be called - but
the iterator isn't only called from assoc_array_find()...
The oops looks something like this:
kernel BUG at /data/fs/linux-2.6-fscache/security/keys/keyring.c:1003!
invalid opcode: 0000 [#1] SMP
...
RIP: keyring_detect_cycle_iterator+0xe/0x1f
...
Call Trace:
search_nested_keyrings+0x76/0x2aa
__key_link_check_live_key+0x50/0x5f
key_link+0x4e/0x85
keyctl_keyring_link+0x60/0x81
SyS_keyctl+0x65/0xe4
tracesys+0xdd/0xe2
The fix is to make keyring_detect_cycle_iterator() check that the key it
has is the key it was actually looking for rather than calling BUG_ON().
A testcase has been included in the keyutils testsuite for this:
http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=
891f3365d07f1996778ade0e3428f01878a1790b
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 9 Mar 2014 20:52:53 +0000 (13:52 -0700)]
Merge branch 'for-rc6' of git://git./linux/kernel/git/rzhang/linux
Pull thermal fixes from Zhang Rui:
"Specifics:
- Update the help text of INT3403 Thermal driver, which was not
friendly to users. From Zhang Rui.
- The "type" sysfs attribute of x86_pkg_temp_thermal registered
thermal zones includes an instance number, which makes the
thermal-to-hwmon bridge fails to group them all in a single hwmon
device. Fixed by Jean Delvare.
- The hwmon device registered by x86_pkg_temp_thermal driver is
redundant because the temperature value reported by
x86_pkg_temp_thermal is already reported by the coretemp driver.
Fixed by Jean Delvare.
- Fix a problem that the cooling device can not be updated properly
if it is initialized at max cooling state. From Ni Wade.
- Fix a problem that OF registered thermal zones are running without
thermal governors. From Zhang Rui.
- Commit
beeb5a1e0ef7 ("thermal: rcar-thermal: Enable driver
compilation with COMPILE_TEST") broke build on archs wihout io
memory. Thus make it depend on HAS_IOMEM to bypass build failures.
Fixed by Richard Weinberger"
* 'for-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
Thermal: thermal zone governor fix
Thermal: Allow first update of cooling device state
thermal,rcar_thermal: Add dependency on HAS_IOMEM
x86_pkg_temp_thermal: Fix the thermal zone type
x86_pkg_temp_thermal: Do not expose as a hwmon device
Thermal: update INT3404 thermal driver help text
Linus Torvalds [Sun, 9 Mar 2014 20:51:47 +0000 (13:51 -0700)]
Merge tag 'spi-v3.14-rc5' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A scattering of driver specific fixes here.
The fixes from Axel cover bitrot in apparently unmaintained drivers,
the at79 bug is fixing a glitch on /CS during initialisation of some
devices which could break some slaves and the remainder are fixes for
recently introduced bugs from the past release cycle or so"
* tag 'spi-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: add missing spi_master_{resume,suspend} calls to PM callbacks
spi: coldfire-qspi: Fix getting correct address for *mcfqspi
spi: fsl-dspi: Fix getting correct address for master
spi: spi-ath79: fix initial GPIO CS line setup
spi: spi-imx: spi_imx_remove: do not disable disabled clocks
spi-topcliff-pch: Fix probing when DMA mode is used
spi/topcliff-pch: Fix DMA channel
Linus Torvalds [Sun, 9 Mar 2014 20:50:14 +0000 (13:50 -0700)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"This series addresses a number of outstanding issues wrt to active I/O
shutdown using iser-target. This includes:
- Fix a long standing tpg_state bug where a tpg could be referenced
during explicit shutdown (v3.1+ stable)
- Use list_del_init for iscsi_cmd->i_conn_node so list_empty checks
work as expected (v3.10+ stable)
- Fix a isert_conn->state related hung task bug + ensure outstanding
I/O completes during session shutdown. (v3.10+ stable)
- Fix isert_conn->post_send_buf_count accounting for RDMA READ/WRITEs
(v3.10+ stable)
- Ignore FRWR completions during active I/O shutdown (v3.12+ stable)
- Fix command leakage for interrupt coalescing during active I/O
shutdown (v3.13+ stable)
Also included is another DIF emulation fix from Sagi specific to
v3.14-rc code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
Target/sbc: Fix sbc_copy_prot for offset scatters
iser-target: Fix command leak for tx_desc->comp_llnode_batch
iser-target: Ignore completions for FRWRs in isert_cq_tx_work
iser-target: Fix post_send_buf_count for RDMA READ/WRITE
iscsi/iser-target: Fix isert_conn->state hung shutdown issues
iscsi/iser-target: Use list_del_init for ->i_conn_node
iscsi-target: Fix iscsit_get_tpg_from_np tpg_state bug
Rafael J. Wysocki [Sun, 9 Mar 2014 17:30:50 +0000 (18:30 +0100)]
Revert "ACPI / sleep: pm_power_off needs more sanity checks to be installed"
Revert commit
3130497f5bab ("ACPI / sleep: pm_power_off needs more
sanity checks to be installed") that breaks power ACPI power off on a
lot of systems, because it checks wrong registers.
Fixes: 3130497f5bab ("ACPI / sleep: pm_power_off needs more sanity checks to be installed")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Sun, 9 Mar 2014 06:56:31 +0000 (22:56 -0800)]
Merge tag 'omap-for-v3.14/fixes-dt-rc4' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Two omap3430 vs 3630 device tree regression fixes for
issues booting 3430 based boards.
* tag 'omap-for-v3.14/fixes-dt-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 9 Mar 2014 06:11:16 +0000 (22:11 -0800)]
Merge tag 'bcm-for-3.14-pinctrl-reduced-rename' of git://github.com/broadcom/bcm11351 into fixes
Merge 'bcm pinctrl rename' From Christin Daudt:
Rename pinctrl dt binding to restore consistency with other bcm mobile
bindings.
* tag 'bcm-for-3.14-pinctrl-reduced-rename' of git://github.com/broadcom/bcm11351:
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
+ Linux 3.14-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sun, 9 Mar 2014 06:09:23 +0000 (22:09 -0800)]
Merge tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux into fixes
Allwinner fixes from Maxime Ripard:
Two fixes for device trees additions that got added in 3.14. One fixes the
interrupt types of some IPs, the other fixes up a compatible that got
introduced during 3.14
* tag 'sunxi-fixes-for-3.14' of https://github.com/mripard/linux:
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 8 Mar 2014 19:57:38 +0000 (11:57 -0800)]
Merge branch 'for-3.14-fixes' of git://git./linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"Two cpuset locking fixes from Li. Both tagged for -stable"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: fix a race condition in __cpuset_node_allowed_softwall()
cpuset: fix a locking issue in cpuset_migrate_mm()
Linus Torvalds [Sat, 8 Mar 2014 19:52:45 +0000 (11:52 -0800)]
Merge branch 'for-3.14-fixes' of git://git./linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Just a couple patches blacklisting more broken devices"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8 (
2BA30001)
libata: disable queued TRIM for Crucial M500 mSATA SSDs
Linus Torvalds [Sat, 8 Mar 2014 19:51:13 +0000 (11:51 -0800)]
Merge branch 'for-3.14-fixes' of git://git./linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"This pull request contains a workqueue usage fix for firewire.
For quite a long time now, workqueue only treats two work items
identical iff both their addresses and callbacks match. This is to
avoid introducing false dependency through the work item being
recycled while being executed. This changes non-reentrancy guarantee
for the users of PREPARE[_DELAYED]_WORK() - if the function changes,
reentrancy isn't guaranteed against the previous instance. Firewire
depended on such nonreentrancy guarantee.
This is fixed by doing the work item multiplexing from firewire proper
while keeping the work function unchanged"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
firewire: don't use PREPARE_DELAYED_WORK
Linus Torvalds [Sat, 8 Mar 2014 18:52:43 +0000 (10:52 -0800)]
Merge tag 'firewire-fixes' of git://git./linux/kernel/git/ieee1394/linux1394
Pull firewire fixes from Stefan Richter:
"Fix a use-after-free regression since v3.4 and an initialization
regression since v3.10"
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: fix probe failure with Agere/LSI controllers
firewire: net: fix use after free
Linus Torvalds [Sat, 8 Mar 2014 18:51:30 +0000 (10:51 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clk driver fix from Mike Turquette:
"Single fix for a clock driver merged in 3.14-rc1. Without this fix
the CPU frequency cannot be scaled"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: shmobile: rcar-gen2: Use kick bit to allow Z clock frequency change
Linus Torvalds [Sat, 8 Mar 2014 17:17:27 +0000 (09:17 -0800)]
Merge tag 'pm+acpi-3.14-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- ACPI tables in some BIOSes list device resources with size equal to
0, which doesn't make sense, so we should ignore them, but instead we
try to use them and mangle things completely. Fix from Zhang Rui.
- Several models of Samsung laptops accumulate EC events when they are
in sleep states which leads to EC buffer overflows that prevent new
events from being signaled after system resume or reboot. This has
been affecting many users for quite a while and may be addressed by
clearing the EC buffer during system resume and system startup on
those machines. From Kieran Clancy.
- If the ACPI sleep control and status registers are not present (which
happens if the Hardware Reduced ACPI mode bit is set in the ACPI
tables, but also may result from BIOS bugs), we should not try to use
ACPI to power off the system and ACPI S5 should not be listed as
supported. Fix from Aubrey Li.
- There's a race condition in cpufreq_get() that leads to a kernel
crash if that function is called at a wrong time. Fix from Aaron
Plattner.
- cpufreq policy objects have to be initialized entirely before they
are first accessed by their users which isn't the case currently and
that potentially leads to various kinds of breakage that is difficult
to debug. Fix from Viresh Kumar.
- Locking is missing in __cpufreq_add_dev() which leads to a race
condition that may trigger a kernel crash. Fix from Viresh Kumar.
* tag 'pm+acpi-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Clear stale EC events on Samsung systems
cpufreq: Initialize governor for a new policy under policy->rwsem
cpufreq: Initialize policy before making it available for others to use
cpufreq: use cpufreq_cpu_get() to avoid cpufreq_get() race conditions
ACPI / sleep: pm_power_off needs more sanity checks to be installed
ACPI / resources: ignore invalid ACPI device resources
Linus Torvalds [Sat, 8 Mar 2014 02:58:40 +0000 (18:58 -0800)]
x86: fix compile error due to X86_TRAP_NMI use in asm files
It's an enum, not a #define, you can't use it in asm files.
Introduced in commit
5fa10196bdb5 ("x86: Ignore NMIs that come in during
early boot"), and sadly I didn't compile-test things like I should have
before pushing out.
My weak excuse is that the x86 tree generally doesn't introduce stupid
things like this (and the ARM pull afterwards doesn't cause me to do a
compile-test either, since I don't cross-compile).
Cc: Don Zickus <dzickus@redhat.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 8 Mar 2014 01:39:32 +0000 (17:39 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A number of ARM updates for -rc, covering mostly ARM specific code,
but with one change to modpost.c to allow Thumb section mismatches to
be detected.
ARM changes include reporting when an attempt is made to boot a LPAE
kernel on hardware which does not support LPAE, rather than just being
silent about it.
A number of other minor fixes are included too"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7992/1: boot: compressed: ignore bswapsdi2.S
ARM: 7991/1: sa1100: fix compile problem on Collie
ARM: fix noMMU kallsyms symbol filtering
ARM: 7980/1: kernel: improve error message when LPAE config doesn't match CPU
ARM: 7964/1: Detect section mismatches in thumb relocations
ARM: 7963/1: mm: report both sections from PMD
Linus Torvalds [Sat, 8 Mar 2014 01:38:36 +0000 (17:38 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A small collection of minor fixes. The FPU stuff is still pending, I
fear. I haven't heard anything from Suresh so I suspect I'm going to
have to dig into the init specifics myself and fix up the patchset"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Ignore NMIs that come in during early boot
x86, trace: Further robustify CR2 handling vs tracing
x86, trace: Fix CR2 corruption when tracing page faults
x86/efi: Quirk out SGI UV
Linus Torvalds [Sat, 8 Mar 2014 01:37:45 +0000 (17:37 -0800)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
Pull power fixes from Ben Herrenschmidt:
"Here are a couple of powerpc fixes for 3.14.
One is (another!) nasty TM problem, we can crash the kernel by forking
inside a transaction. The other one is a simple fix for an alignment
issue which can hurt in LE mode"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Align p_dyn, p_rela and p_st symbols
powerpc/tm: Fix crash when forking inside a transaction
Linus Torvalds [Sat, 8 Mar 2014 00:32:40 +0000 (16:32 -0800)]
Merge tag 'trace-fixes-v3.14-rc5' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"In the past, I've had lots of reports about trace events not working.
Developers would say they put a trace_printk() before and after the
trace event but when they enable it (and the trace event said it was
enabled) they would see the trace_printks but not the trace event.
I was not able to reproduce this, but that's because I wasn't looking
at the right location. Recently, another bug came up that showed the
issue.
If your kernel supports signed modules but allows for non-signed
modules to be loaded, then when one is, the kernel will silently set
the MODULE_FORCED taint on the module. Although, this taint happens
without the need for insmod --force or anything of the kind, it labels
the module with that taint anyway.
If this tainted module has tracepoints, the tracepoints will be
ignored because of the MODULE_FORCED taint. But no error message will
be displayed. Worse yet, the event infrastructure will still be
created letting users enable the trace event represented by the
tracepoint, although that event will never actually be enabled. This
is because the tracepoint infrastructure allows for non-existing
tracepoints to be enabled for new modules to arrive and have their
tracepoints set.
Although there are several things wrong with the above, this change
only addresses the creation of the trace event files for tracepoints
that are not created when a module is loaded and is tainted. This
change will print an error message about the module being tainted and
not the trace events will not be created, and it does not create the
trace event infrastructure"
* tag 'trace-fixes-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not add event files for modules that fail tracepoints
Linus Torvalds [Sat, 8 Mar 2014 00:31:41 +0000 (16:31 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
- a bugfix for a long standing waitqueue race
- a trivial fix for a missing include
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Include missing header file in irqdomain.c
genirq: Remove racy waitqueue_active check
Ditang Chen [Fri, 7 Mar 2014 05:27:57 +0000 (13:27 +0800)]
SUNRPC: Fix oops when trace sunrpc_task events in nfs client
When tracking sunrpc_task events in nfs client, the clnt pointer may be NULL.
[ 139.269266] BUG: unable to handle kernel NULL pointer dereference at
0000000000000004
[ 139.269915] IP: [<
ffffffffa026f216>] ftrace_raw_event_rpc_task_running+0x86/0xf0 [sunrpc]
[ 139.269915] PGD
1d293067 PUD
1d294067 PMD 0
[ 139.269915] Oops: 0000 [#1] SMP
[ 139.269915] Modules linked in: nfsv4 dns_resolver nfs lockd sunrpc fscache sg ppdev e1000
serio_raw pcspkr parport_pc parport i2c_piix4 i2c_core microcode xfs libcrc32c sd_mod sr_mod
cdrom ata_generic crc_t10dif crct10dif_common pata_acpi ahci libahci ata_piix libata dm_mirror
dm_region_hash dm_log dm_mod
[ 139.269915] CPU: 0 PID: 59 Comm: kworker/0:2 Not tainted 3.10.0-84.el7.x86_64 #1
[ 139.269915] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 139.269915] Workqueue: rpciod rpc_async_schedule [sunrpc]
[ 139.269915] task:
ffff88001b598000 ti:
ffff88001b632000 task.ti:
ffff88001b632000
[ 139.269915] RIP: 0010:[<
ffffffffa026f216>] [<
ffffffffa026f216>] ftrace_raw_event_rpc_task_running+0x86/0xf0 [sunrpc]
[ 139.269915] RSP: 0018:
ffff88001b633d70 EFLAGS:
00010206
[ 139.269915] RAX:
ffff88001dfc5338 RBX:
ffff88001cc37a00 RCX:
ffff88001dfc5334
[ 139.269915] RDX:
ffff88001dfc5338 RSI:
0000000000000000 RDI:
ffff88001dfc533c
[ 139.269915] RBP:
ffff88001b633db0 R08:
000000000000002c R09:
000000000000000a
[ 139.269915] R10:
0000000000062180 R11:
00000020759fb9dc R12:
ffffffffa0292c20
[ 139.269915] R13:
ffff88001dfc5334 R14:
0000000000000000 R15:
0000000000000000
[ 139.269915] FS:
0000000000000000(0000) GS:
ffff88001fc00000(0000) knlGS:
0000000000000000
[ 139.269915] CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
[ 139.269915] CR2:
0000000000000004 CR3:
000000001d290000 CR4:
00000000000006f0
[ 139.269915] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 139.269915] DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
[ 139.269915] Stack:
[ 139.269915]
000000001b633d98 0000000000000246 ffff88001df1dc00 ffff88001cc37a00
[ 139.269915]
ffff88001bc35e60 0000000000000000 ffff88001ffa0a48 ffff88001bc35ee0
[ 139.269915]
ffff88001b633e08 ffffffffa02704b5 0000000000010000 ffff88001cc37a70
[ 139.269915] Call Trace:
[ 139.269915] [<
ffffffffa02704b5>] __rpc_execute+0x1d5/0x400 [sunrpc]
[ 139.269915] [<
ffffffffa0270706>] rpc_async_schedule+0x26/0x30 [sunrpc]
[ 139.269915] [<
ffffffff8107867b>] process_one_work+0x17b/0x460
[ 139.269915] [<
ffffffff8107942b>] worker_thread+0x11b/0x400
[ 139.269915] [<
ffffffff81079310>] ? rescuer_thread+0x3e0/0x3e0
[ 139.269915] [<
ffffffff8107fc80>] kthread+0xc0/0xd0
[ 139.269915] [<
ffffffff8107fbc0>] ? kthread_create_on_node+0x110/0x110
[ 139.269915] [<
ffffffff815d122c>] ret_from_fork+0x7c/0xb0
[ 139.269915] [<
ffffffff8107fbc0>] ? kthread_create_on_node+0x110/0x110
[ 139.269915] Code: 4c 8b 45 c8 48 8d 7d d0 89 4d c4 41 89 c9 b9 28 00 00 00 e8 9d b4 e9
e0 48 85 c0 49 89 c5 74 a2 48 89 c7 e8 9d 3f e9 e0 48 89 c2 <41> 8b 46 04 48 8b 7d d0 4c
89 e9 4c 89 e6 89 42 0c 0f b7 83 d4
[ 139.269915] RIP [<
ffffffffa026f216>] ftrace_raw_event_rpc_task_running+0x86/0xf0 [sunrpc]
[ 139.269915] RSP <
ffff88001b633d70>
[ 139.269915] CR2:
0000000000000004
[ 140.946406] ---[ end trace
ba486328b98d7622 ]---
Signed-off-by: Ditang Chen <chendt.fnst@cn.fujitsu.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Rafael J. Wysocki [Sat, 8 Mar 2014 00:07:31 +0000 (01:07 +0100)]
Merge branch 'pm-cpufreq'
* pm-cpufreq:
cpufreq: Initialize governor for a new policy under policy->rwsem
cpufreq: Initialize policy before making it available for others to use
cpufreq: use cpufreq_cpu_get() to avoid cpufreq_get() race conditions
Rafael J. Wysocki [Sat, 8 Mar 2014 00:07:06 +0000 (01:07 +0100)]
Merge branches 'acpi-resources', 'acpi-ec' and 'acpi-sleep'
* acpi-resources:
ACPI / resources: ignore invalid ACPI device resources
* acpi-ec:
ACPI / EC: Clear stale EC events on Samsung systems
* acpi-sleep:
ACPI / sleep: pm_power_off needs more sanity checks to be installed
Linus Torvalds [Fri, 7 Mar 2014 23:17:36 +0000 (15:17 -0800)]
Merge tag 'dm-3.14-fixes-3' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- dm-cache memory allocation failure fix
- fix DM's Kconfig identation
- dm-snapshot metadata corruption fix for bug introduced in 3.14-rc1
- important refcount < 0 fix for the DM persistent data library's space
map metadata interface which fixes corruption reported by a few
dm-thinp users
and last but not least:
- more extensive fixes than ideal for dm-thinp's data resize capability
(which has had growing pain much like we've seen from -ENOSPC
handling of filesystems that mature).
The end result is dm-thinp now handles metadata operation failure and
no data space error conditions much better than before.
* tag 'dm-3.14-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm space map metadata: fix refcount decrement below 0 which caused corruption
dm thin: fix Documentation for held metadata root feature
dm thin: fix noflush suspend IO queueing
dm thin: fix deadlock in __requeue_bio_list
dm thin: fix out of data space handling
dm thin: ensure user takes action to validate data and metadata consistency
dm thin: synchronize the pool mode during suspend
dm snapshot: fix metadata corruption
dm: fix Kconfig indentation
dm cache mq: fix memory allocation failure for large cache devices
H. Peter Anvin [Fri, 7 Mar 2014 23:05:20 +0000 (15:05 -0800)]
x86: Ignore NMIs that come in during early boot
Don Zickus reports:
A customer generated an external NMI using their iLO to test kdump
worked. Unfortunately, the machine hung. Disabling the nmi_watchdog
made things work.
I speculated the external NMI fired, caused the machine to panic (as
expected) and the perf NMI from the watchdog came in and was latched.
My guess was this somehow caused the hang.
----
It appears that the latched NMI stays latched until the early page
table generation on 64 bits, which causes exceptions to happen which
end in IRET, which re-enable NMI. Therefore, ignore NMIs that come in
during early execution, until we have proper exception handling.
Reported-and-tested-by: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/r/1394221143-29713-1-git-send-email-dzickus@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.5+, older with some backport effort
Mark Rutland [Wed, 26 Feb 2014 16:21:26 +0000 (17:21 +0100)]
ARM: 7992/1: boot: compressed: ignore bswapsdi2.S
Commit
017f161a55b4 (ARM: 7877/1: use built-in byte swap function) added
bswapsdi2.{o,S} to arch/arm/boot/compressed/Makefile, but didn't update
the .gitignore. Thus after a a build git status shows bswapsdi2.S as a
new file, which is a little annoying.
This patch updates arch/arm/boot/compressed/.gitignore to ignore
bswapsdi2.S, as we already do for ashldi3.S and others.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Walleij [Tue, 25 Feb 2014 21:41:41 +0000 (22:41 +0100)]
ARM: 7991/1: sa1100: fix compile problem on Collie
Due to a problem in the MFD Kconfig it was not possible to
compile the UCB battery driver for the Collie SA1100 system,
in turn making it impossible to compile in the battery driver.
(See patch "mfd: include all drivers in subsystem menu".)
After fixing the MFD Kconfig (separate patch) a compile error
appears in the Collie battery driver due to the <mach/collie.h>
implicitly requiring <mach/hardware.h> through <linux/gpio.h>
via <mach/gpio.h> prior to commit
40ca061b "ARM: 7841/1: sa1100: remove complex GPIO interface".
Fix this up by including the required header into
<mach/collie.h>.
Cc: stable@vger.kernel.org
Cc: Andrea Adami <andrea.adami@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 26 Feb 2014 19:40:46 +0000 (19:40 +0000)]
ARM: fix noMMU kallsyms symbol filtering
With noMMU, CONFIG_PAGE_OFFSET was not being set correctly. As there's
no MMU, PAGE_OFFSET should be equal to PHYS_OFFSET in all cases. This
commit makes that explicit.
Since we do this, we don't need to mess around in asm/memory.h with
ifdefs to sort this out, so let's get rid of that, and there's no point
offering the "Memory split" option for noMMU as that's meaningless
there.
Fixes: b9b32bf70f2f ("ARM: use linker magic for vectors and vector stubs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mathias Nyman [Fri, 7 Mar 2014 15:06:58 +0000 (17:06 +0200)]
Revert "USBNET: ax88179_178a: enable tso if usb host supports sg dma"
This reverts commit
3804fad45411b48233b48003e33a78f290d227c8.
This commit, together with commit
247bf557273dd775505fb9240d2d152f4f20d304
"xhci 1.0: Limit arbitrarily-aligned scatter gather." were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules for xHCI 1.0 hosts,
but for now, revert this patch until scatter gather can be properly supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 7 Mar 2014 15:06:57 +0000 (17:06 +0200)]
Revert "xhci 1.0: Limit arbitrarily-aligned scatter gather."
This reverts commit
247bf557273dd775505fb9240d2d152f4f20d304.
This commit, together with commit
3804fad45411b48233b48003e33a78f290d227c8
"USBNET: ax88179_178a: enable tso if usb host supports sg dma" were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules required, but for now
this patch needs to be reverted to get USB 3.0 mass storage devices working at the
level they used to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julius Werner [Tue, 4 Mar 2014 19:27:38 +0000 (11:27 -0800)]
usb: Make DELAY_INIT quirk wait 100ms between Get Configuration requests
The DELAY_INIT quirk only reduces the frequency of enumeration failures
with the Logitech HD Pro C920 and C930e webcams, but does not quite
eliminate them. We have found that adding a delay of 100ms between the
first and second Get Configuration request makes the device enumerate
perfectly reliable even after several weeks of extensive testing. The
reasons for that are anyone's guess, but since the DELAY_INIT quirk
already delays enumeration by a whole second, wating for another 10th of
that isn't really a big deal for the one other device that uses it, and
it will resolve the problems with these webcams.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julius Werner [Tue, 4 Mar 2014 18:52:39 +0000 (10:52 -0800)]
usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e
We've encountered a rare issue when enumerating two Logitech webcams
after a reboot that doesn't power cycle the USB ports. They are spewing
random data (possibly some leftover UVC buffers) on the second
(full-sized) Get Configuration request of the enumeration phase. Since
the data is random this can potentially cause all kinds of odd behavior,
and since it occasionally happens multiple times (after the kernel
issues another reset due to the garbled configuration descriptor), it is
not always recoverable. Set the USB_DELAY_INIT quirk that seems to work
around the issue.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michele Baldessari [Fri, 7 Mar 2014 16:34:29 +0000 (16:34 +0000)]
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8 (
2BA30001)
Via commit
87809942d3fa "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk
for Seagate Momentus SpinPoint M8" we added a quirk for disks named
"ST1000LM024 HN-M101MBB" with firmware revision "2AR10001".
As reported on https://bugzilla.redhat.com/show_bug.cgi?id=
1073901,
we need to also add firmware revision
2BA30001 as it is broken as well.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Vineet Gupta [Fri, 7 Mar 2014 07:52:22 +0000 (13:22 +0530)]
ARC: Use correct PTAG register for icache flush
This fixes a subtle issue with cache flush which could potentially cause
random userspace crashes because of stale icache lines.
This error crept in when consolidating the cache flush code
Fixes: bd12976c3664 (ARC: cacheflush refactor #3: Unify the {d,i}cache)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 3.13
Cc: arc-linux-dev@synopsys.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 7 Mar 2014 18:02:39 +0000 (10:02 -0800)]
Merge tag 'sound-3.14-rc6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few device-specific quirks for HD-audio and USB-audio, most of
which are one-liners"
* tag 'sound-3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add quirk for Logitech Webcam C500
ALSA: hda - Use analog beep for Thinkpads with AD1984 codecs
ALSA: hda - Add missing loopback merge path for AD1884/1984 codecs
ALSA: hda - add automute fix for another dell AIO model
ALSA: hda - Added inverted digital-mic handling for Acer TravelMate 8371
Linus Torvalds [Fri, 7 Mar 2014 18:01:47 +0000 (10:01 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Mostly intel and radeon fixes, one tda998x, one kconfig dep fix and
two more MAINTAINERS updates,
All pretty run of the mill for this stage"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/atom: select the proper number of lanes in transmitter setup
MAINTAINERS: add maintainer entry for TDA998x driver
drm: fix bochs kconfig dependencies
drm/radeon/dpm: fix typo in EVERGREEN_SMC_FIRMWARE_HEADER_softRegisters
drm/radeon/cik: fix typo in documentation
drm/radeon: silence GCC warning on 32 bit
drm/radeon: resume old pm late
drm/radeon: TTM must be init with cpu-visible VRAM, v2
DRM: armada: fix use of kfifo_put()
drm/i915: Reject >165MHz modes w/ DVI monitors
drm/i915: fix assert_cursor on BDW
drm/i915: vlv: reserve GT power context early
drm/i915: fix pch pci device enumeration
drm/i915: Resolving the memory region conflict for Stolen area
drm/i915: use backlight legacy combination mode also for i915gm/i945gm
MAINTAINERS: update AGP tree to point at drm tree
Linus Torvalds [Fri, 7 Mar 2014 17:59:44 +0000 (09:59 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Small collection of fixes for 3.14-rc. It contains:
- Three minor update to blk-mq from Christoph.
- Reduce number of unaligned (< 4kb) in-flight writes on mtip32xx to
two. From Micron.
- Make the blk-mq CPU notify spinlock raw, since it can't be a
sleeper spinlock on RT. From Mike Galbraith.
- Drop now bogus BUG_ON() for bio iteration with blk integrity. From
Nic Bellinger.
- Properly propagate the SYNC flag on requests. From Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: add REQ_SYNC early
rt,blk,mq: Make blk_mq_cpu_notify_lock a raw spinlock
bio-integrity: Drop bio_integrity_verify BUG_ON in post bip->bip_iter world
blk-mq: support partial I/O completions
blk-mq: merge blk_mq_insert_request and blk_mq_run_request
blk-mq: remove blk_mq_alloc_rq
mtip32xx: Reduce the number of unaligned writes to 2
Linus Torvalds [Fri, 7 Mar 2014 17:54:40 +0000 (09:54 -0800)]
Merge tag 'pinctrl-v3.14-3' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"This is a set of pin control fixes I have collected over the last few
days. Some have rotated more than others in linux-next, but they were
rebased on v3.14-rc5 due to sloppy commit messages. I am quite
convinced that they are all good fixes that only hit this or that
individual driver and not the entire subsystem.
- Fix chained interrupts, interrupt masking and register offset
calculation for the sunxi driver
- Make MSM a bool rather than a tristate to stop build problems to
happen - chained interrupt controllers cannot currently be defined
in modules
- Fix a clock in the PFC driver
- Fix a kernel panic in the sirf driver"
* tag 'pinctrl-v3.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sirf: fix kernel panic in gpio_lock_as_irq
pinctrl: sh-pfc: r8a7791: SD1_CLK fix
pinctrl: msm: make PINCTRL_MSM bool instead of tristate
pinctrl: sunxi: Fix interrupt register offset calculation
pinctrl: sunxi: Fix masking when setting irq type
pinctrl: sunxi: use chained_irq_{enter, exit} for GIC compatibility
Linus Torvalds [Fri, 7 Mar 2014 17:53:24 +0000 (09:53 -0800)]
Merge tag 'stable/for-linus-3.14-rc5-tag' of git://git./linux/kernel/git/xen/tip
Pull Xen fix from Konrad Rzeszutek Wilk:
"This has exactly one patch for Xen ARM. It sets the dependency to
compile the kernel with MMU enabled - otherwise - the guest won't work
very well"
* tag 'stable/for-linus-3.14-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
ARM: XEN depends on having a MMU
Linus Torvalds [Fri, 7 Mar 2014 17:52:46 +0000 (09:52 -0800)]
Merge tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming
Pull c6x build fix from Mark Salter:
"Build fix for c6x"
* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
c6x: fix build failure caused by cache.h
Joe Thornber [Fri, 7 Mar 2014 14:57:19 +0000 (14:57 +0000)]
dm space map metadata: fix refcount decrement below 0 which caused corruption
This has been a relatively long-standing issue that wasn't nailed down
until Teng-Feng Yang's meticulous bug report to dm-devel on 3/7/2014,
see: http://www.redhat.com/archives/dm-devel/2014-March/msg00021.html
From that report:
"When decreasing the reference count of a metadata block with its
reference count equals 3, we will call dm_btree_remove() to remove
this enrty from the B+tree which keeps the reference count info in
metadata device.
The B+tree will try to rebalance the entry of the child nodes in each
node it traversed, and the rebalance process contains the following
steps.
(1) Finding the corresponding children in current node (shadow_current(s))
(2) Shadow the children block (issue BOP_INC)
(3) redistribute keys among children, and free children if necessary (issue BOP_DEC)
Since the update of a metadata block's reference count could be
recursive, we will stash these reference count update operations in
smm->uncommitted and then process them in a FILO fashion.
The problem is that step(3) could free the children which is created
in step(2), so the BOP_DEC issued in step(3) will be carried out
before the BOP_INC issued in step(2) since these BOPs will be
processed in FILO fashion. Once the BOP_DEC from step(3) tries to
decrease the reference count of newly shadow block, it will report
failure for its reference equals 0 before decreasing. It looks like we
can solve this issue by processing these BOPs in a FIFO fashion
instead of FILO."
Commit
5b564d80 ("dm space map: disallow decrementing a reference count
below zero") changed the code to report an error for this temporary
refcount decrement below zero. So what was previously a harmless
invalid refcount became a hard failure due to the new error path:
device-mapper: space map common: unable to decrement a reference count below 0
device-mapper: thin: 253:6: dm_thin_insert_block() failed: error = -22
device-mapper: thin: 253:6: switching pool to read-only mode
This bug is in dm persistent-data code that is common to the DM thin and
cache targets. So any users of those targets should apply this fix.
Fix this by applying recursive space map operations in FIFO order rather
than FILO.
Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=68801
Reported-by: Apollon Oikonomopoulos <apoikos@debian.org>
Reported-by: edwillam1007@gmail.com
Reported-by: Teng-Feng Yang <shinrairis@gmail.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.13+
Tejun Heo [Fri, 7 Mar 2014 15:19:57 +0000 (10:19 -0500)]
firewire: don't use PREPARE_DELAYED_WORK
PREPARE_[DELAYED_]WORK() are being phased out. They have few users
and a nasty surprise in terms of reentrancy guarantee as workqueue
considers work items to be different if they don't have the same work
function.
firewire core-device and sbp2 have been been multiplexing work items
with multiple work functions. Introduce fw_device_workfn() and
sbp2_lu_workfn() which invoke fw_device->workfn and
sbp2_logical_unit->workfn respectively and always use the two
functions as the work functions and update the users to set the
->workfn fields instead of overriding work functions using
PREPARE_DELAYED_WORK().
This fixes a variety of possible regressions since
a2c1c57be8d9
"workqueue: consider work function when searching for busy work items"
due to which fw_workqueue lost its required non-reentrancy property.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: linux1394-devel@lists.sourceforge.net
Cc: stable@vger.kernel.org # v3.9+
Cc: stable@vger.kernel.org # v3.8.2+
Cc: stable@vger.kernel.org # v3.4.60+
Cc: stable@vger.kernel.org # v3.2.40+
Shaohua Li [Wed, 19 Feb 2014 12:20:21 +0000 (20:20 +0800)]
blk-mq: add REQ_SYNC early
Add REQ_SYNC early, so rq_dispatched[] in blk_mq_rq_ctx_init
is set correctly.
Signed-off-by: Shaohua Li<shli@fusionio.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Sagi Grimberg [Wed, 5 Mar 2014 12:05:09 +0000 (14:05 +0200)]
Target/sbc: Fix sbc_copy_prot for offset scatters
When copying between device and command protection scatters
we must take into account that device scatters might be offset
and we might copy outside scatter range. Thus for each cmd prot
scatter we must take the min between cmd prot scatter, dev prot
scatter, and whats left (and loop in case we havn't copied enough
from/to cmd prot scatter).
Example (single t_prot_sg of len 2048):
kernel: sbc_dif_copy_prot: se_cmd=
ffff880380aaf970, left=2048, len=2048, dev_prot_sg_offset=3072, dev_prot_sg_len=4096
kernel: isert: se_cmd=
ffff880380aaf970 PI error found type 0 at sector 0x2600 expected 0x0 vs actual 0x725f, lba=2580
Instead of copying 2048 from offset 3072 (copying junk outside sg
limit 4096), we must to copy 1024 and continue to next sg until
we complete cmd prot scatter.
This issue was found using iSER T10-PI offload over rd_mcp (wasn't
discovered with fileio since file_dev prot sglists are never offset).
Changes from v1:
- Fix sbc_copy_prot copy length miss-calculation
Changes from v0:
- Removed psg->offset consideration for psg_len computation
- Removed sg->offset consideration for offset condition
- Added copied consideraiton for len computation
- Added copied offset to paddr when doing memcpy
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
James Hogan [Tue, 4 Mar 2014 11:28:48 +0000 (11:28 +0000)]
gpio-tz1090: Replace commas with semi-colons
Replace commas with semicolons between irqchip callback initialisation
statements in tz1090_gpio_bank_probe. The commas appear to be a subtle
remnant of when the irqchips were statically initialised.
Thanks to Thomas Gleixner for spotting it while whipping up a coccinelle
script.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 7 Mar 2014 02:12:49 +0000 (10:12 +0800)]
gpio: remove misleading documentation
It is currently debated where the functions to lock a certain
GPIO line as used for IRQs should be called. Delete all
misleading documentation.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mark Brown [Fri, 7 Mar 2014 03:08:13 +0000 (11:08 +0800)]
Merge remote-tracking branches 'spi/fix/ath79', 'spi/fix/atmel', 'spi/fix/coldfire', 'spi/fix/fsl-dspi', 'spi/fix/imx' and 'spi/fix/topcliff-pch' into spi-linus
Anton Blanchard [Mon, 3 Mar 2014 21:31:24 +0000 (08:31 +1100)]
powerpc: Align p_dyn, p_rela and p_st symbols
The 64bit relocation code places a few symbols in the text segment.
These symbols are only 4 byte aligned where they need to be 8 byte
aligned. Add an explicit alignment.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 3 Mar 2014 03:21:40 +0000 (14:21 +1100)]
powerpc/tm: Fix crash when forking inside a transaction
When we fork/clone we currently don't copy any of the TM state to the new
thread. This results in a TM bad thing (program check) when the new process is
switched in as the kernel does a tmrechkpt with TEXASR FS not set. Also, since
R1 is from userspace, we trigger the bad kernel stack pointer detection. So we
end up with something like this:
Bad kernel stack pointer 0 at
c0000000000404fc
cpu 0x2: Vector: 700 (Program Check) at [
c00000003ffefd40]
pc:
c0000000000404fc: restore_gprs+0xc0/0x148
lr:
0000000000000000
sp: 0
msr:
9000000100201030
current = 0xc000001dd1417c30
paca = 0xc00000000fe00800 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/2
WARNING: exception is not recoverable, can't continue
The below fixes this by flushing the TM state before we copy the task_struct to
the clone. To do this we go through the tmreclaim patch, which removes the
checkpointed registers from the CPU and transitions the CPU out of TM suspend
mode. Hence we need to call tmrechkpt after to restore the checkpointed state
and the TM mode for the current task.
To make this fail from userspace is simply:
tbegin
li r0, 2
sc
<boom>
Kudos to Adhemerval Zanella Neto for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Adhemerval Zanella Neto <azanella@br.ibm.com>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fabio Estevam [Wed, 26 Feb 2014 11:12:37 +0000 (08:12 -0300)]
gpio: gpio-pl061: Use %pa to print 'resource_size_t'
The following build warning is generated when building multi_v7_defconfig with
LPAE option selected:
drivers/gpio/gpio-pl061.c:358:2: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' [-Wformat=]
Fix it by using %pa to print 'resource_size_t'.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Alan Tull [Thu, 6 Mar 2014 19:29:40 +0000 (13:29 -0600)]
fix build error in gpio-dwapb patch
fix build error with this message:
kernel/irq/Kconfig:41:error: recursive dependency detected!
kernel/irq/Kconfig:41: symbol GENERIC_IRQ_CHIP is selected by GPIO_DWAPB
drivers/gpio/Kconfig:131: symbol GPIO_DWAPB depends on IRQ_DOMAIN
kernel/irq/Kconfig:46: symbol IRQ_DOMAIN is selected by GENERIC_IRQ_CHIP
Signed-off-by: Alan Tull <atull@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dave Airlie [Thu, 6 Mar 2014 23:27:22 +0000 (09:27 +1000)]
Merge branch 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
one more radeon fix.
* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/atom: select the proper number of lanes in transmitter setup
Alex Deucher [Thu, 6 Mar 2014 23:09:52 +0000 (18:09 -0500)]
drm/radeon/atom: select the proper number of lanes in transmitter setup
We need to check for DVI vs. HDMI when setting up duallink since
HDMI is single link only. Fixes 4k modes on newer asics.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=75223
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Russell King [Mon, 3 Mar 2014 12:18:14 +0000 (12:18 +0000)]
MAINTAINERS: add maintainer entry for TDA998x driver
Add a maintainers entry for the TDA998x driver. Rob Clark has handed
this driver over to me to look after.
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Gerd Hoffmann [Thu, 6 Mar 2014 12:26:36 +0000 (13:26 +0100)]
drm: fix bochs kconfig dependencies
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 6 Mar 2014 23:04:32 +0000 (09:04 +1000)]
Merge branch 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox into drm-fixes
fix for kfifo api change.
* 'drm-armada-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
DRM: armada: fix use of kfifo_put()
Dave Airlie [Thu, 6 Mar 2014 22:41:12 +0000 (08:41 +1000)]
Merge branch 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
a few more radeon fixes.
* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix typo in EVERGREEN_SMC_FIRMWARE_HEADER_softRegisters
drm/radeon/cik: fix typo in documentation
drm/radeon: silence GCC warning on 32 bit
drm/radeon: resume old pm late
drm/radeon: TTM must be init with cpu-visible VRAM, v2
Alex Deucher [Thu, 6 Mar 2014 18:16:55 +0000 (13:16 -0500)]
drm/radeon/dpm: fix typo in EVERGREEN_SMC_FIRMWARE_HEADER_softRegisters
Should be at 0x8 rather than 0.
fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60523
Noticed by ArtForz on #radeon
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Tue, 4 Mar 2014 20:50:29 +0000 (15:50 -0500)]
drm/radeon/cik: fix typo in documentation
Copy-paste typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Paul Bolle [Tue, 4 Mar 2014 09:34:48 +0000 (10:34 +0100)]
drm/radeon: silence GCC warning on 32 bit
Building radeon_ttm.o on 32 bit x86 triggers a warning:
In file included from include/asm-generic/bug.h:13:0,
from [...]/arch/x86/include/asm/bug.h:38,
from include/linux/bug.h:4,
from include/drm/drm_mm.h:39,
from include/drm/drm_vma_manager.h:26,
from include/drm/ttm/ttm_bo_api.h:35,
from drivers/gpu/drm/radeon/radeon_ttm.c:32:
drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_gtt_read':
include/linux/kernel.h:712:17: warning: comparison of distinct pointer types lacks a cast [enabled by default]
(void) (&_min1 == &_min2); \
^
drivers/gpu/drm/radeon/radeon_ttm.c:938:22: note: in expansion of macro 'min'
ssize_t cur_size = min(size, PAGE_SIZE - off);
^
Silence this warning by using min_t(). Since cur_size will never be
negative and its upper bound is PAGE_SIZE, we can change its type to
size_t and use min_t(size_t, [...]) here.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Alex Deucher [Tue, 25 Feb 2014 17:01:28 +0000 (12:01 -0500)]
drm/radeon: resume old pm late
Moving the pm resume up in the init order to fix
dpm seems to have regressed somes cases with the old
pm code. Move it back to late resume.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lauri Kasanen [Fri, 28 Feb 2014 18:50:23 +0000 (20:50 +0200)]
drm/radeon: TTM must be init with cpu-visible VRAM, v2
Without this, a bo may get created in the cpu-inaccessible vram.
Before the CP engines get setup, all copies are done via cpu memcpy.
This means that the cpu tries to read from inaccessible memory, fails,
and the radeon module proceeds to disable acceleration.
Doing this has no downsides, as the real VRAM size gets set as soon as the
CP engines get init.
This is a candidate for 3.14 fixes.
v2: Add comment on why the function is used
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
This page took 0.055202 seconds and 5 git commands to generate.