Chuck Lever [Thu, 18 Jun 2009 01:02:14 +0000 (18:02 -0700)]
NFS: More "sloppy" parsing problems
Specifying "port=-5" with the kernel's current mount option parser
generates "unrecognized mount option". If "sloppy" is set, this
causes the mount to succeed and use the default values; the desired
behavior is that, since this is a valid option with an invalid value,
the mount should fail, even with "sloppy."
To properly handle "sloppy" parsing, we need to distinguish between
correct options with invalid values, and incorrect options. We will
need to parse integer values by hand, therefore, and not rely on
match_token().
For instance, these must all fail with "invalid value":
port=
12345678
port=-5
port=samuel
and not with "unrecognized option," as they do currently.
Thus, for the sake of match_token() we need to treat the values for
these options as strings, and do the conversion to integers using
strict_strtol().
This is basically the same solution we used for the earlier "retry="
fix (commit
ecbb3845), except in this case the kernel actually has to
parse the value, rather than ignore it.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:13 +0000 (18:02 -0700)]
NFS: Invalid mount option values should always fail, even with "sloppy"
Ian Kent reports:
"I've noticed a couple of other regressions with the options vers
and proto option of mount.nfs(8).
The commands:
mount -t nfs -o vers=<invalid version> <server>:/<path> /<mountpoint>
mount -t nfs -o proto=<invalid proto> <server>:/<path> /<mountpoint>
both immediately fail.
But if the "-s" option is also used they both succeed with the
mount falling back to defaults (by the look of it).
In the past these failed even when the sloppy option was given, as
I think they should. I believe the sloppy option is meant to allow
the mount command to still function for mount options (for example
in shared autofs maps) that exist on other Unix implementations but
aren't present in the Linux mount.nfs(8). So, an invalid value
specified for a known mount option is different to an unknown mount
option and should fail appropriately."
See RH bugzilla 486266.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:13 +0000 (18:02 -0700)]
NFS: Remove unused XDR decoder functions
Clean up: Remove xdr_decode_fhstatus() and xdr_decode_fhstatus3(), now
that they are unused.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:13 +0000 (18:02 -0700)]
NFS: Update MNT and MNT3 reply decoding functions
Solder xdr_stream-based XDR decoding functions into the in-kernel mountd
client that are more careful about checking data types and watching for
buffer overflows. The new MNT3 decoder includes support for auth-flavor
list decoding.
The "_sz" macro for MNT3 replies was missing the size of the file handle.
I've added this back, and included the size of the auth flavor array.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:12 +0000 (18:02 -0700)]
NFS: add XDR decoder for mountd version 3 auth-flavor lists
Introduce an xdr_stream-based XDR decoder that can unpack the auth-
flavor list returned in a MNT3 reply.
The nfs_mount() function's caller allocates an array, and passes the
size and a pointer to it. The decoder decodes all the flavors it can
into the array, and returns the number of decoded flavors.
If the caller is not interested in the auth flavors, it can pass a
value of zero as the size of the pre-allocated array.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:12 +0000 (18:02 -0700)]
NFS: add new file handle decoders to in-kernel mountd client
Introduce xdr_stream-based XDR file handle decoders to the in-kernel
mountd client. These are more careful than the existing decoder
functions about buffer overflows and data type and range checking.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:12 +0000 (18:02 -0700)]
NFS: Add separate mountd status code decoders for each mountd version
Introduce data structures and xdr_stream-based decoding functions for
unmarshalling mountd status codes properly.
Mountd version 3 uses specific standard error return codes that are
not errno values and not NFS3ERR_ values. These have a well-defined
standard mapping to local errno values. Introduce data structures
and a decoder function that map these status codes to local errno
values properly. This is new functionality (but not used yet).
Version 1 mountd status values are defined by RFC 1094 as UNIX error
values (errno values). Errno values on heterogeneous systems do not
necessarily match each other. To avoid exposing possibly incorrect
errno values to upper layers, the current XDR decoder converts all
non-zero MNT version 1 status codes to -EACCES.
The OpenGroup XNFS standard provides a mapping similar to but smaller
than the version 3 error codes. Implement a decoder that uses the XNFS
error codes, replacing the current decoder.
For both mountd protocol versions, map unrecognized errors to -EACCES.
Finally we introduce a replacement data structure for mnt_fhstatus
at this time, which is used by the new XDR decoders. In addition to
documenting that the status value returned by the XDR decoders is
always an errno, this new structure will be expanded in subsequent
patches.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:11 +0000 (18:02 -0700)]
NFS: remove unused function in fs/nfs/mount_clnt.c
Clean up: remove xdr_encode_dirpath() now that it has been replaced.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:11 +0000 (18:02 -0700)]
NFS: Use xdr_stream-based XDR encoder for MNT's dirpath argument
Check the length of the supplied dirpath, and see that it fits
properly in the RPC buffer.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:11 +0000 (18:02 -0700)]
NFS: Clean up MNT program definitions
Clean up: Relocate MNT program procedure number definitions to the
only file that uses them. Relocate the version number definitions,
which are shared, to nfs.h. Remove duplicate program number
definitions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:11 +0000 (18:02 -0700)]
lockd: Don't bother with RPC ping for NSM upcalls
Cut NSM upcall RPC traffic in half -- don't do a NULL call first.
The cases where a ping would be helpful are rare.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:10 +0000 (18:02 -0700)]
lockd: Update NSM state from SM_MON replies
When rpc.statd starts up in user space at boot time, it attempts to
write the latest NSM local state number into
/proc/sys/fs/nfs/nsm_local_state.
If lockd.ko isn't loaded yet (as is the case in most configurations),
that file doesn't exist, thus the kernel's NSM state remains set to
its initial value of zero during lockd operation.
This is a problem because rpc.statd and lockd use the NSM state number
to prevent repeated lock recovery on rebooted hosts. If lockd sends
a zero NSM state, but then a delayed SM_NOTIFY with a real NSM state
number is received, there is no way for lockd or rpc.statd to
distinguish that stale SM_NOTIFY from an actual reboot. Thus lock
recovery could be performed after the rebooted host has already
started reclaiming locks, and those locks will be lost.
We could change /etc/init.d/nfslock so it always modprobes lockd.ko
before starting rpc.statd. However, if lockd.ko is ever unloaded
and reloaded, we are back at square one, since the NSM state is not
preserved across an unload/reload cycle. This may happen frequently
on clients that use automounter. A period of NFS inactivity causes
lockd.ko to be unloaded, and the kernel loses its NSM state setting.
Instead, let's use the fact that rpc.statd plants the local system's
NSM state in every SM_MON (and SM_UNMON) reply. lockd performs a
synchronous SM_MON upcall to the local rpc.statd _before_ sending its
first NLM request to a new remote. This would permit rpc.statd to
provide the current NSM state to lockd, even after lockd.ko had been
unloaded and reloaded.
Note that NLMPROC_LOCK arguments are constructed before the
nsm_monitor() call, so we have to rearrange argument construction very
slightly to make this all work out.
And, the kernel appears to treat NSM state as a u32 (see struct
nlm_args and nsm_res). Make nsm_local_state a u32 as well, to ensure
we don't get bogus comparison results.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:10 +0000 (18:02 -0700)]
NFS: Fix false error return from nfs_callback_up() if ipv6.ko is not available
Clear "ret" if the error return from svc_create_xprt(AF_INET6) was
-EAFNOSUPORT. Otherwise, callback start-up will succeed, but
nfs_callback_up() will return -EAFNOSUPPORT anyway, and the first
NFSv4 mount attempt after a reboot will fail.
Bug introduced by commit
f738f517 in 2.6.30-rc1.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:10 +0000 (18:02 -0700)]
NFS: Return error code from nfs_callback_up() to user space
If the kernel cannot start the NFSv4 callback service during a mount
request, it returns -ENOMEM to user space, resulting in this message:
mount.nfs4: Cannot allocate memory
Adjust nfs_alloc_client() and nfs_get_client() to pass NFSv4 callback
start-up errors back to user space so a less mysterious error message
can be displayed by the mount command.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Chuck Lever [Thu, 18 Jun 2009 01:02:09 +0000 (18:02 -0700)]
NFS: Do not display the setting of the "intr" mount option
The "intr" mount option has been deprecated for a while, but
/proc/mounts continues to display "nointr" whether "intr" or "nointr"
has been specified for a mount point.
Since these options do not have any effect, simply do not display
them.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Suresh Jayaraman [Thu, 18 Jun 2009 01:02:09 +0000 (18:02 -0700)]
NFS: add support for splice writes
Adds support for splice writes. It effectively calls
generic_file_splice_write() to do the writes.
We need not worry about O_APPEND case as the combination of splice()
writes and O_APPEND is disallowed. This patch propagates NFS write
errors back to the caller. The number of bytes written via splice are
being added to NFSIO_NORMALWRITTENBYTES as these are effectively
cached writes.
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 17 Jun 2009 20:23:01 +0000 (13:23 -0700)]
NFSv4/NLM: Push file locking BKL dependencies down into the NLM layer
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 17 Jun 2009 20:23:00 +0000 (13:23 -0700)]
NFS: Ensure we always hold the BKL when dereferencing inode->i_flock
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 17 Jun 2009 20:22:59 +0000 (13:22 -0700)]
NFSv4: Handle more errors when recovering open file and locking state
It is possible for servers to return NFS4ERR_BAD_STATEID when
the state management code is recovering locks or is reclaiming state when
returning a delegation. Ensure that we handle that case.
While we're at it, add in handlers for NFS4ERR_STALE,
NFS4ERR_ADMIN_REVOKED, NFS4ERR_OPENMODE, NFS4ERR_DENIED and
NFS4ERR_STALE_STATEID, since the protocol appears to allow for them too.
Also handle ENOMEM...
Finally, rather than add new NFSv4.0-specific errors and error handling into
the generic delegation code, move that open file and locking state error
handling into the NFSv4 layer.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 17 Jun 2009 20:22:58 +0000 (13:22 -0700)]
NFSv4: Move error handling out of the delegation generic code
The NFSv4 delegation recovery code is required by the protocol to handle
more errors. Rather than add NFSv4.0 specific errors into 'generic'
delegation code, we should move the error handling into the NFSv4 layer.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 17 Jun 2009 20:22:58 +0000 (13:22 -0700)]
NFSv4: Fix the 'nolock' option regression
NFSv4 should just ignore the 'nolock' option. It is an NFSv2/v3 thing...
This fixes the Oops in http://bugzilla.kernel.org/show_bug.cgi?id=13330
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 17 Jun 2009 20:22:57 +0000 (13:22 -0700)]
SUNRPC: Fix a missing "break" option in xs_tcp_setup_socket()
In the case of -EADDRNOTAVAIL and/or unhandled connection errors, we want
to get rid of the existing socket and retry immediately, just as the
comment says. Currently we end up sleeping for a minute, due to the missing
"break" statement.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Wed, 17 Jun 2009 17:42:21 +0000 (10:42 -0700)]
Merge branch 'kmemleak' of git://linux-arm.org/linux-2.6
* 'kmemleak' of git://linux-arm.org/linux-2.6:
kmemleak: Fix some typos in comments
kmemleak: Rename kmemleak_panic to kmemleak_stop
kmemleak: Only use GFP_KERNEL|GFP_ATOMIC for the internal allocations
Catalin Marinas [Wed, 17 Jun 2009 17:29:04 +0000 (18:29 +0100)]
kmemleak: Fix some typos in comments
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Wed, 17 Jun 2009 17:29:03 +0000 (18:29 +0100)]
kmemleak: Rename kmemleak_panic to kmemleak_stop
This is to avoid the confusion created by the "panic" word.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Catalin Marinas [Wed, 17 Jun 2009 17:29:02 +0000 (18:29 +0100)]
kmemleak: Only use GFP_KERNEL|GFP_ATOMIC for the internal allocations
Kmemleak allocates memory for pointer tracking and it tries to avoid
using GFP_ATOMIC if the caller doesn't require it. However other gfp
flags may be passed by the caller which aren't required by kmemleak.
This patch filters the gfp flags so that only GFP_KERNEL | GFP_ATOMIC
are used.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Linus Torvalds [Wed, 17 Jun 2009 16:51:50 +0000 (09:51 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] cpumask: new cpumask operators for arch/x86/kernel/cpu/cpufreq/powernow-k8.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in powernow-k8.c
[CPUFREQ] cpumask: avoid cpumask games in arch/x86/kernel/cpu/cpufreq/speedstep-centrino.c
[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c
[CPUFREQ] powernow-k8: get drv data for correct CPU
[CPUFREQ] powernow-k8: read P-state from HW
[CPUFREQ] reduce scope of ACPI_PSS_BIOS_BUG_MSG[]
[CPUFREQ] Clean up convoluted code in arch/x86/kernel/tsc.c:time_cpufreq_notifier()
[CPUFREQ] minor correction to cpu-freq documentation
[CPUFREQ] powernow-k8.c: mess cleanup
[CPUFREQ] Only set sampling_rate_max deprecated, sampling_rate_min is useful
[CPUFREQ] powernow-k8: Set transition latency to 1 if ACPI tables export 0
[CPUFREQ] ondemand: Uncouple minimal sampling rate from HZ in NO_HZ case
Linus Torvalds [Wed, 17 Jun 2009 16:50:44 +0000 (09:50 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
Linus Torvalds [Wed, 17 Jun 2009 16:48:30 +0000 (09:48 -0700)]
Merge branch 'linux-next' of git://git.infradead.org/ubi-2.6
* 'linux-next' of git://git.infradead.org/ubi-2.6: (21 commits)
UBI: add reboot notifier
UBI: handle more error codes
UBI: fix multiple spelling typos
UBI: fix kmem_cache_free on error patch
UBI: print amount of reserved PEBs
UBI: improve messages in the WL worker
UBI: make gluebi a separate module
UBI: remove built-in gluebi
UBI: add notification API
UBI: do not switch to R/O mode on read errors
UBI: fix and clean-up error paths in WL worker
UBI: introduce new constants
UBI: fix race condition
UBI: minor serialization fix
UBI: do not panic if volume check fails
UBI: add dump_stack in checking code
UBI: fix races in I/O debugging checks
UBI: small debugging code optimization
UBI: improve debugging messages
UBI: re-name volumes_mutex to device_mutex
...
Linus Torvalds [Wed, 17 Jun 2009 16:46:33 +0000 (09:46 -0700)]
Merge branch 'linux-next' of git://git.infradead.org/ubifs-2.6
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: start using hrtimers
hrtimer: export ktime_add_safe
UBIFS: do not forget to register BDI device
UBIFS: allow sync option in rootflags
UBIFS: remove dead code
UBIFS: use anonymous device
UBIFS: return proper error code if the compr is not present
UBIFS: return error if link and unlink race
UBIFS: reset no_space flag after inode deletion
Andrew Morton [Wed, 17 Jun 2009 05:38:29 +0000 (22:38 -0700)]
Documentation/vm/Makefile: don't try to build slqbinfo
For it is only in linux-next at this stage.
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Wed, 17 Jun 2009 07:21:13 +0000 (17:21 +1000)]
drm/radeon/kms: remove the _DRM_DRIVER from the KMS paths.
This causes an issue since we fixed the drm mappings to do the right thing,
so its just a copy and pasto.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 17 Jun 2009 16:41:25 +0000 (09:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
SLUB: Fix early boot GFP_DMA allocations
SLUB: Don't print out OOM warning for __GFP_NOFAIL
SLUB: fix build when !SLUB_DEBUG
SLUB: Out-of-memory diagnostics
slab: document kzfree() zeroing behavior
slab: fix generic PAGE_POISONING conflict with SLAB_RED_ZONE
slob: use PG_slab for identifying SLOB pages
Linus Torvalds [Wed, 17 Jun 2009 16:13:52 +0000 (09:13 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (47 commits)
MIPS: Add hibernation support
MIPS: Move Cavium CP0 hwrena impl bits to cpu-feature-overrides.h
MIPS: Allow CPU specific overriding of CP0 hwrena impl bits.
MIPS: Kconfig Add SYS_SUPPORTS_HUGETLBFS and enable it for some systems.
Hugetlbfs: Enable hugetlbfs for more systems in Kconfig.
MIPS: TLB support for hugetlbfs.
MIPS: Add hugetlbfs page defines.
MIPS: Add support files for hugetlbfs.
MIPS: Remove unused parameters from iPTE_LW.
Staging: Add octeon-ethernet driver files.
MIPS: Export erratum function needed by octeon-ethernet driver.
MIPS: Cavium-Octeon: Add more chip specific feature tests.
MIPS: Cavium-Octeon: Add more board type constants.
MIPS: Export cvmx_sysinfo_get needed by octeon-ethernet driver.
MIPS: Add named alloc functions to OCTEON boot monitor memory allocator.
MIPS: Alchemy: devboards: Convert to gpio calls.
MIPS: Alchemy: xxs1500: use linux gpio api.
MIPS: Alchemy: MTX-1: Use linux gpio api.
MIPS: Alchemy: Rewrite GPIO support.
MIPS: Alchemy: Remove unused au1000_gpio.h header
...
Linus Torvalds [Wed, 17 Jun 2009 15:46:57 +0000 (08:46 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
get rid of BKL in fs/sysv
get rid of BKL in fs/minix
get rid of BKL in fs/efs
befs ->pust_super() doesn't need BKL
Cleanup of adfs headers
9P doesn't need BKL in ->umount_begin()
fuse doesn't need BKL in ->umount_begin()
No instance of ->bmap() needs BKL
remove unlock_kernel() left accidentally
ext4: avoid unnecessary spinlock in critical POSIX ACL path
ext3: avoid unnecessary spinlock in critical POSIX ACL path
Wu Zhangjin [Thu, 4 Jun 2009 12:27:10 +0000 (20:27 +0800)]
MIPS: Add hibernation support
[Ralf: SMP support requires CPU hotplugging which MIPS currently doesn't
support. As implemented in this patch cache and tlb flushing will also be
invoked with interrupts disabled so smp_call_function() will blow up in
charming ways. So limit to !SMP.]
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Yan Hua <yanh@lemote.com>
Reviewed-by: Arnaud Patard <apatard@mandriva.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Hu Hongbing <huhb@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 13 May 2009 22:59:56 +0000 (15:59 -0700)]
MIPS: Move Cavium CP0 hwrena impl bits to cpu-feature-overrides.h
We had an ugly #ifdef for Cavium Octeon hwrena bits in traps.c, remove
it to mach-cavium-octeon/cpu-feature-overrides.h
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 13 May 2009 22:59:55 +0000 (15:59 -0700)]
MIPS: Allow CPU specific overriding of CP0 hwrena impl bits.
Some CPUs have implementation dependent rdhwr registers. Allow them
to be enabled on a per CPU basis.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 28 May 2009 00:47:46 +0000 (17:47 -0700)]
MIPS: Kconfig Add SYS_SUPPORTS_HUGETLBFS and enable it for some systems.
Add new kconfig variables SYS_SUPPORTS_HUGETLBFS and
CPU_SUPPORTS_HUGEPAGES. They are enabled for systems that are known
to support huge pages.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 28 May 2009 00:47:45 +0000 (17:47 -0700)]
Hugetlbfs: Enable hugetlbfs for more systems in Kconfig.
As part of adding hugetlbfs support for MIPS, I am adding a new
kconfig variable 'SYS_SUPPORTS_HUGETLBFS'. Since some mips cpu
varients don't yet support it, we can enable selection of HUGETLBFS on
a system by system basis from the arch/mips/Kconfig.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
CC: William Irwin <wli@holomorphy.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 28 May 2009 00:47:44 +0000 (17:47 -0700)]
MIPS: TLB support for hugetlbfs.
The TLB handlers need to check for huge pages and give them special
handling. Huge pages consist of two contiguous sub-pages of physical
memory.
* Loading entrylo0 and entrylo1 need to be handled specially.
* The page mask must be set for huge pages and then restored after
writing the TLB entries.
* The PTE for huge pages resides in the PMD, we halt traversal of the
tables there.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 28 May 2009 00:47:43 +0000 (17:47 -0700)]
MIPS: Add hugetlbfs page defines.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Thu, 28 May 2009 00:47:42 +0000 (17:47 -0700)]
MIPS: Add support files for hugetlbfs.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Fri, 8 May 2009 22:10:50 +0000 (15:10 -0700)]
MIPS: Remove unused parameters from iPTE_LW.
The l parameter to iPTE_LW() is unused. Remove it and from some of its
callers as well.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 6 May 2009 00:35:21 +0000 (17:35 -0700)]
Staging: Add octeon-ethernet driver files.
The octeon-ethernet driver supports the sgmii, rgmii, spi, and xaui
ports present on the Cavium OCTEON family of SOCs. These SOCs are
multi-core mips64 processors with existing support over in arch/mips.
The driver files can be categorized into three basic groups:
1) Register definitions, these are named cvmx-*-defs.h
2) Main driver code, these have names that don't start cvmx-.
3) Interface specific functions and other utility code, names starting
with cvmx-
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 6 May 2009 00:35:20 +0000 (17:35 -0700)]
MIPS: Export erratum function needed by octeon-ethernet driver.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 6 May 2009 00:35:19 +0000 (17:35 -0700)]
MIPS: Cavium-Octeon: Add more chip specific feature tests.
The octeon-ethernet driver needs to check for additional chip specific
features, we add them to the octeon_has_feature() framework.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 6 May 2009 00:35:18 +0000 (17:35 -0700)]
MIPS: Cavium-Octeon: Add more board type constants.
The bootloader now uses additional board type constants. The
octeon-ethernet driver needs some of the new values.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 6 May 2009 00:35:17 +0000 (17:35 -0700)]
MIPS: Export cvmx_sysinfo_get needed by octeon-ethernet driver.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 6 May 2009 00:35:16 +0000 (17:35 -0700)]
MIPS: Add named alloc functions to OCTEON boot monitor memory allocator.
The various Octeon ethernet drivers use these new functions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sat, 6 Jun 2009 12:09:58 +0000 (14:09 +0200)]
MIPS: Alchemy: devboards: Convert to gpio calls.
Replace a few open-coded GPIO register accesses with gpio calls.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sat, 6 Jun 2009 12:09:57 +0000 (14:09 +0200)]
MIPS: Alchemy: xxs1500: use linux gpio api.
Replace a few GPIO register accesses in the board init code with calls to
the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sat, 6 Jun 2009 12:09:56 +0000 (14:09 +0200)]
MIPS: Alchemy: MTX-1: Use linux gpio api.
Replace a few GPIO register accesses in the board init code with calls
to the gpio api.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sat, 6 Jun 2009 12:09:55 +0000 (14:09 +0200)]
MIPS: Alchemy: Rewrite GPIO support.
The current in-kernel Alchemy GPIO support is far too inflexible for
all my use cases. To address this, the following changes are made:
* create generic functions which deal with manipulating the on-chip
GPIO1/2 blocks. Such functions are universally useful.
* Macros for GPIO2 shared interrupt management and block control.
* support for both built-in CONFIG_GPIOLIB and fast, inlined GPIO macros.
If CONFIG_GPIOLIB is not enabled, provide linux gpio framework
compatibility by directly inlining the GPIO1/2 functions. GPIO access
is limited to on-chip ones and they can be accessed as documented in
the datasheets (GPIO0-31 and 200-215).
If CONFIG_GPIOLIB is selected, two (2) gpio_chip-s, one for GPIO1 and
one for GPIO2, are registered. GPIOs can still be accessed by using
the numberspace established in the databooks.
However this is not yet flexible enough for my uses: My Alchemy
systems have a documented "external" gpio interface (fixed, different
numberspace) and can support a variety of baseboards, some of which
are equipped with I2C gpio expanders. I want to be able to provide
the default 16 GPIOs of the CPU board numbered as 0..15 and also
support gpio expanders, if present, starting as gpio16.
To achieve this, a new Kconfig symbol for Alchemy is introduced,
CONFIG_ALCHEMY_GPIO_INDIRECT, which boards can enable to signal
that they don't want the Alchemy numberspace exposed to the outside
world, but instead want to provide their own. Boards are now respon-
sible for providing the linux gpio interface glue code (either in a
custom gpio.h header (in board include directory) or with gpio_chips).
To make the board-specific inlined gpio functions work, the MIPS
Makefile must be changed so that the mach-au1x00/gpio.h header is
included _after_ the board headers, by moving the inclusion of
the mach-au1x00/ to the end of the header list.
See arch/mips/include/asm/mach-au1x00/gpio.h for more info.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss [Sat, 6 Jun 2009 12:09:54 +0000 (14:09 +0200)]
MIPS: Alchemy: Remove unused au1000_gpio.h header
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Matthieu Castet [Sun, 24 May 2009 17:48:51 +0000 (19:48 +0200)]
MIPS: BCM47xx: Fix gpio_direction_output
gpio_direction_output should also set an output value according to the API.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 17 Jun 2009 10:06:28 +0000 (11:06 +0100)]
MIPS: ioctl.h: Cleanup.
o Rewrite to use <asm-generic/ioctl.h>. Cuts down the file from 40 to
16 lines.
o Delete _IOC_VOID, _IOC_OUT, _IOC_IN and _IOC_INOUT. They were added
for 2.1.14 but I was not able to find any user - not even historical
ones.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Tue, 2 Jun 2009 14:54:22 +0000 (23:54 +0900)]
MIPS: TXx9: Add TX4939 RNG support
Add platform support for RNG of TX4939 SoC.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Tue, 2 Jun 2009 14:54:21 +0000 (23:54 +0900)]
MIPS: hwrng: Add TX4939 RNG driver
This patch adds support for the integrated RNG of the TX4939 SoC.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Mon, 25 May 2009 13:04:02 +0000 (22:04 +0900)]
MIPS: TXx9: Add SRAMC support
Add a sysdev to access SRAM in TXx9 SoCs via sysfs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Imre Kaloz [Tue, 2 Jun 2009 12:22:06 +0000 (14:22 +0200)]
MIPS: Sibyte: Remove standalone kernel support
CFE is the only supported and used bootloader on the SiByte boards,
the standalone kernel support has been never used outside Broadcom.
Remove it and make the kernel use CFE by default.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Imre Kaloz [Tue, 2 Jun 2009 12:22:00 +0000 (14:22 +0200)]
MIPS: Sibyte: Remove simulator option
This patch removes the SiByte simulation Kconfig option, which only modified
a printk.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Thu, 21 May 2009 17:49:47 +0000 (19:49 +0200)]
MIPS: RB532: Check irq number when handling GPIO interrupts
This patch makes sure that we are not going to clear
or change the interrupt status of a GPIO interrupt
superior to 13 as this is the maximum number of GPIO
interrupt source (p.232 of the RC32434 reference manual).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Thu, 21 May 2009 17:49:39 +0000 (19:49 +0200)]
MIPS: RB532: Cleanup cpu-features-overrides
Remove commented out definitions.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 12 May 2009 19:41:55 +0000 (12:41 -0700)]
MIPS: Remove dead case label.
CPU_CAVIUM_OCTEON is mips_r2 which is handled before the switch. This
label in the switch statement is dead code, so we remove it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 12 May 2009 19:41:54 +0000 (12:41 -0700)]
MIPS: Remove execution hazard barriers for Octeon.
The Octeon has no execution hazards, so we can remove them and save an
instruction per TLB handler invocation.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Reviewed by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 12 May 2009 19:41:53 +0000 (12:41 -0700)]
MIPS: Allow R2 CPUs to turn off generation of 'ehb' instructions.
Some CPUs do not need ehb instructions after writing CP0 registers.
By allowing ehb generation to be overridden in
cpu-feature-overrides.h, we can save a few instructions in the TLB
handler hot paths.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 20 May 2009 18:40:59 +0000 (11:40 -0700)]
MIPS: Fold the TLB refill at the vmalloc path if possible.
Try to fold the 64-bit TLB refill handler opportunistically at the
beginning of the vmalloc path so as to avoid splitting execution flow in
half and wasting cycles for a branch required at that point then. Resort
to doing the split if either of the newly created parts would not fit into
its designated slot.
Original-patch-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Wed, 20 May 2009 18:40:58 +0000 (11:40 -0700)]
MIPS: Replace some magic numbers with symbolic values in tlbex.c
The logic used to split the r4000 refill handler is liberally
sprinkled with magic numbers. We attempt to explain what they are and
normalize them against a new symbolic value (MIPS64_REFILL_INSNS).
CC: David VomLehn <dvomlehn@cisco.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Tue, 19 May 2009 13:12:22 +0000 (22:12 +0900)]
MIPS: TXx9: Add ACLC support
Add platform support for ACLC of TXx9 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Fri, 24 Apr 2009 00:44:38 +0000 (17:44 -0700)]
MIPS: Add Cavium OCTEON PCI support.
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Fri, 24 Apr 2009 00:44:37 +0000 (17:44 -0700)]
MIPS: Add register definitions for PCI.
Here we add the register definitions for the processor blocks used by
the following PCI support patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Wed, 22 Apr 2009 15:40:31 +0000 (00:40 +0900)]
MIPS: TXx9: Add DMAC support
Add platform support for DMAC of TXx9 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Wed, 22 Apr 2009 15:40:30 +0000 (00:40 +0900)]
DMA: TXx9 Soc DMA Controller driver
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Thu, 23 Apr 2009 15:10:36 +0000 (00:10 +0900)]
MIPS: TXx9: micro optimization for clocksource and clock_event
Use container structure for clocksource, clock_event_device and hold a
pointer to txx9_tmr_reg in it.
This saves a few instructions in clocksource and clock_event handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Kevin Cernekee [Fri, 24 Apr 2009 00:36:53 +0000 (17:36 -0700)]
MIPS: Support 64-byte D-cache line size
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Kevin Cernekee [Fri, 24 Apr 2009 00:25:12 +0000 (17:25 -0700)]
MIPS: Pass struct device to plat_dma_addr_to_phys()
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Kevin Cernekee [Fri, 24 Apr 2009 00:03:43 +0000 (17:03 -0700)]
MIPS: Add size and direction arguments to plat_unmap_dma_mem()
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 17 Jun 2009 10:06:24 +0000 (11:06 +0100)]
MIPS: SB1250: Sort out merge mistake.
A wrong resolution of a merge conflict made the recently deleted wrong
error check in sb1250_set_affinity. Send the zombie back to the empire
of the undead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Tue, 9 Jun 2009 02:12:48 +0000 (11:12 +0900)]
MIPS: Fix __ndelay build error and add 'ull' suffix for 32-bit kernel
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 17 Jun 2009 10:06:24 +0000 (11:06 +0100)]
MIPS: SMTC: Fix formatting difference to linux-mips.org code
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Fri, 12 Jun 2009 16:28:00 +0000 (17:28 +0100)]
MIPS: Fix typo resulting in far too long ndelay times.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pekka Enberg [Wed, 17 Jun 2009 05:30:54 +0000 (08:30 +0300)]
Merge branch 'slub/earlyboot' into for-linus
Conflicts:
mm/slub.c
Pekka Enberg [Wed, 17 Jun 2009 05:30:15 +0000 (08:30 +0300)]
Merge branches 'slab/documentation', 'slab/fixes', 'slob/cleanups' and 'slub/fixes' into for-linus
Al Viro [Wed, 17 Jun 2009 03:59:37 +0000 (23:59 -0400)]
get rid of BKL in fs/sysv
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Wed, 17 Jun 2009 03:47:45 +0000 (23:47 -0400)]
get rid of BKL in fs/minix
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Wed, 17 Jun 2009 03:35:46 +0000 (23:35 -0400)]
get rid of BKL in fs/efs
Only readdir() really needed it, and that's easily fixable by switch to
generic_file_llseek()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Wed, 17 Jun 2009 03:24:50 +0000 (23:24 -0400)]
befs ->pust_super() doesn't need BKL
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 16 Jun 2009 18:52:13 +0000 (14:52 -0400)]
Cleanup of adfs headers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 16 Jun 2009 18:17:21 +0000 (14:17 -0400)]
9P doesn't need BKL in ->umount_begin()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 16 Jun 2009 18:15:00 +0000 (14:15 -0400)]
fuse doesn't need BKL in ->umount_begin()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 16 Jun 2009 17:35:01 +0000 (13:35 -0400)]
No instance of ->bmap() needs BKL
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
J. R. Okajima [Tue, 16 Jun 2009 16:16:50 +0000 (01:16 +0900)]
remove unlock_kernel() left accidentally
commit
337eb00a2c3a421999c39c94ce7e33545ee8baa7
Push BKL down into ->remount_fs()
and
commit
4aa98cf768b6f2ea4b204620d949a665959214f6
Push BKL down into do_remount_sb()
were uncorrectly merged.
The former removes one pair of lock/unlock_kernel(), but the latter adds
several unlock_kernel(). Finally a few unlock_kernel() calls left.
Signed-off-by: J. R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Theodore Ts'o [Mon, 8 Jun 2009 19:22:25 +0000 (15:22 -0400)]
ext4: avoid unnecessary spinlock in critical POSIX ACL path
If a filesystem supports POSIX ACL's, the VFS layer expects the filesystem
to do POSIX ACL checks on any files not owned by the caller, and it does
this for every single pathname component that it looks up.
That obviously can be pretty expensive if the filesystem isn't careful
about it, especially with locking. That's doubly sad, since the common
case tends to be that there are no ACL's associated with the files in
question.
ext4 already caches the ACL data so that it doesn't have to look it up
over and over again, but it does so by taking the inode->i_lock spinlock
on every lookup. Which is a noticeable overhead even if it's a private
lock, especially on CPU's where the serialization is expensive (eg Intel
Netburst aka 'P4').
For the special case of not actually having any ACL's, all that locking is
unnecessary. Even if somebody else were to be changing the ACL's on
another CPU, we simply don't care - if we've seen a NULL ACL, we might as
well use it.
So just load the ACL speculatively without any locking, and if it was
NULL, just use it. If it's non-NULL (either because we had a cached
entry, or because the cache hasn't been filled in at all), it means that
we'll need to get the lock and re-load it properly.
(This commit was ported from a patch originally authored by Linus for
ext3.)
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Mon, 8 Jun 2009 19:22:24 +0000 (15:22 -0400)]
ext3: avoid unnecessary spinlock in critical POSIX ACL path
If a filesystem supports POSIX ACL's, the VFS layer expects the filesystem
to do POSIX ACL checks on any files not owned by the caller, and it does
this for every single pathname component that it looks up.
That obviously can be pretty expensive if the filesystem isn't careful
about it, especially with locking. That's doubly sad, since the common
case tends to be that there are no ACL's associated with the files in
question.
ext3 already caches the ACL data so that it doesn't have to look it up
over and over again, but it does so by taking the inode->i_lock spinlock
on every lookup. Which is a noticeable overhead even if it's a private
lock, especially on CPU's where the serialization is expensive (eg Intel
Netburst aka 'P4').
For the special case of not actually having any ACL's, all that locking is
unnecessary. Even if somebody else were to be changing the ACL's on
another CPU, we simply don't care - if we've seen a NULL ACL, we might as
well use it.
So just load the ACL speculatively without any locking, and if it was
NULL, just use it. If it's non-NULL (either because we had a cached
entry, or because the cache hasn't been filled in at all), it means that
we'll need to get the lock and re-load it properly.
This is noticeable even on Nehalem, which does locking quite well (much
better than P4). From lmbench:
Processor, Processes - times in microseconds - smaller is better
--------------------------------------------------------------------
Host OS Mhz null null open slct fork exec sh
call I/O stat clos TCP proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ----
- before:
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.95 1.45 2.18 69.1 273. 1141
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.95 1.48 2.28 69.9 253. 1140
nehalem.l Linux 2.6.30- 3193 0.04 0.10 0.95 1.42 2.19 68.6 284. 1141
- after:
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.92 1.44 2.12 68.3 282. 1094
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.92 1.39 2.20 67.0 308. 1123
nehalem.l Linux 2.6.30- 3193 0.04 0.09 0.92 1.39 2.36 67.4 293. 1148
where you can see what appears to be a roughly 3% improvement in stat
and open/close latencies from just the removal of the locking overhead.
Of course, this only matters for files you don't own (the owner never
needs to do the ACL checks), but that's the common case for libraries,
header files, and executables. As well as for the base components of any
absolute pathname, even if you are the owner of the final file.
[ At some point we probably want to move this ACL caching logic entirely
into the VFS layer (and only call down to the filesystem when
uncached), but in the meantime this improves ext3 a bit.
A similar fix to btrfs makes a much bigger difference (15x improvement
in lmbench) due to broken caching. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Wed, 17 Jun 2009 04:26:42 +0000 (21:26 -0700)]
Merge branch 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: Make driver depend on MACH_U300
i2c-s3c2410: use resource_size()
i2c: Use resource_size macro
i2c: ST DDC I2C U300 bus driver v3
i2c-bfin-twi: pull in io.h for ioremap()
Linus Torvalds [Wed, 17 Jun 2009 04:20:39 +0000 (21:20 -0700)]
Merge branch 'drm-linus' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: switch to using late_initcall
radeon legacy chips: tv dac bg/dac adj updates
drm/radeon: introduce kernel modesetting for radeon hardware
drm: Add the TTM GPU memory manager subsystem.
drm: Memory fragmentation from lost alignment blocks
drm/radeon: fix mobility flags on new PCI IDs.
David Howells [Tue, 16 Jun 2009 20:36:49 +0000 (21:36 +0100)]
AFS: Correctly translate auth error aborts and don't failover in such cases
Authentication error abort codes should be translated to appropriate
Linux error codes, rather than all being translated to EREMOTEIO - which
indicates that the server had internal problems.
Additionally, a server shouldn't be marked unavailable and the next
server tried if an authentication error occurs. This will quickly make
all the servers unavailable to the client. Instead the error should be
returned straight to the user.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Tue, 16 Jun 2009 20:36:44 +0000 (21:36 +0100)]
RxRPC: Don't attempt to reuse aborted connections
Connections that have seen a connection-level abort should not be reused
as the far end will just abort them again; instead a new connection
should be made.
Connection-level aborts occur due to such things as authentication
failures.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 17 Jun 2009 04:15:42 +0000 (21:15 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (425 commits)
V4L/DVB (11870): gspca - main: VIDIOC_ENUM_FRAMESIZES ioctl added.
V4L/DVB (12004): poll method lose race condition
V4L/DVB (11894): flexcop-pci: dmesg visible names broken
V4L/DVB (11892): Siano: smsendian - declare function as extern
V4L/DVB (11891): Siano: smscore - bind the GPIO SMS protocol
V4L/DVB (11890): Siano: smscore - remove redundant code
V4L/DVB (11889): Siano: smsdvb - add DVB v3 events
V4L/DVB (11888): Siano: smsusb - remove redundant ifdef
V4L/DVB (11887): Siano: smscards - add board (target) events
V4L/DVB (11886): Siano: smscore - fix some new GPIO definitions names
V4L/DVB (11885): Siano: Add new GPIO management interface
V4L/DVB (11884): Siano: smssdio - revert to stand alone module
V4L/DVB (11883): Siano: cards - add two additional (USB) devices
V4L/DVB (11824): Siano: smsusb - change exit func debug msg
V4L/DVB (11823): Siano: smsusb - fix typo in module description
V4L/DVB (11822): Siano: smscore - bug fix at get_device_mode
V4L/DVB (11821): Siano: smscore - fix isdb-t firmware name
V4L/DVB (11820): Siano: smscore - fix byte ordering bug
V4L/DVB (11819): Siano: smscore - fix get_common_buffer bug
V4L/DVB (11818): Siano: smscards - assign gpio to HPG targets
...
This page took 0.046096 seconds and 5 git commands to generate.