Joonyoung Shim [Thu, 23 Jul 2009 08:33:17 +0000 (17:33 +0900)]
ASoC: MAX9877: fix write operation for register
The MAX9877 needs an address of start register when we write values to
registers through i2c_master_send(), but the code for this was missed in
max9877_write_regs().
If the value of control is 0 in the max9877_set_out_mode(), the value is
not increased to 1, but actually the value to write to the register
should be 1.
And the register bits for out_mode and osc_mode should be cleared before
writing.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Janusz Krzysztofik [Wed, 22 Jul 2009 03:22:28 +0000 (05:22 +0200)]
ASoC: Add support for Conexant CX20442-11 voice modem codec
This patch adds support for Conexant CX20442-11 voice modem codec, suitable
for use by the ASoC board driver for Amstrad E3 (Delta) videophone. Related
sound card driver will follow.
This codec is an optional part of the Conexant SmartV three chip modem design.
As such, documentation for its proprietary digital audio interface is not
available. However, on Amstrad Delta board, thanks to Mark Underwood who
created an initial, omap-alsa based sound driver a few years ago[1], the codec
has been discovered to be accessible not only from the modem side, but also
over the OMAP McBSP based CPU DAI. Thus, the driver can be used by any sound
card that can access the codec DAI directly. The DAI configuration parameters
(sample rate and format, number of channels) has been selected out empirically
for best user experience.
The codec analogue interface consists of two pairs of analogue I/O pins:
speakerphone interface or telephone handset/headset interface. Furthermore, it
seams to provide two operation modes for speakerphone I/O: standard and
advanced, with automatic gain control and echo cancelation. Even if the codec
control interface is unknown and not available, all those interfaces and modes
can be selected over the modem chip using V.253 commands. The driver is able
to issue necessary commands over a suitable hw_write function if provided by a
sound card driver. Otherwise, the codec can be controlled over the modem from
userspace while inactive.
Even if nothig is known about the codec internal power management
capabilities, DAPM widgets has been used to model the codec audio map.
Automatically performed powering up/down of those virtual widgets results in
corresponding V.253 commands being issued.
Some driver features/oddities may be board specific, but I have no way to
verify that with any board other than Amstrad Delta.
[1] http://www.earth.li/pipermail/e3-hacking/2006-April/000481.html
Created and tested against linux-2.6.31-rc3.
Applies and works with linux-omap-2.6 commit
7c5cb7862d32cb344be7831d466535d5255e35ac as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 23 Jul 2009 07:22:58 +0000 (08:22 +0100)]
Merge branch 'for-2.6.31' into for-2.6.32
Lopez Cruz, Misael [Thu, 23 Jul 2009 01:45:03 +0000 (20:45 -0500)]
ASoC: OMAP: Staticise pcm creation function of omap-pcm
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Chaithrika U S [Wed, 22 Jul 2009 11:45:04 +0000 (07:45 -0400)]
ASoC: tlv320aic3x: Enable PLL when not bypassed
PLL was not being enabled when it was not bypassed. This patch
enables the PLL when it is used. Additionally, it disables the PLL
when it is bypassed.
Without this patch, the audio on TI DM646x EVM and DM355 EVM
does not work properly. The bit clocks and the frame sync signals
from the codec are not correct and hence the playback/record are faster
than usual for most sample rates. The reason for this was that the PLL
was not enabled when it was not bypassed.
Tested on DM6467 EVM, playback tested on DM355 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Joonyoung Shim [Wed, 22 Jul 2009 05:09:08 +0000 (14:09 +0900)]
ASoC: MAX9877: separate callback functions
The callback function to control register was used by whole controls in
MAX9877 driver, but this causes using many if statement for double
register control or invert.
So, the callback function for double register control is separate
differently, and the code for invert is added in the callback function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
John Bonesio [Tue, 21 Jul 2009 20:15:40 +0000 (13:15 -0700)]
ASoC: MPC5200: Increase the delay time between resets
Reset was failing with the original udelay(50) between the code in
psc_ac97_cold_reset() and the call to psc_ac97_warm_reset(). Through testing
it was found that a delay of 1ms was necessary for the cold_reset code to
consistently complete successfully.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sat, 18 Jul 2009 10:09:42 +0000 (11:09 +0100)]
ASoC: Fix checkpatch issues in AD1938
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 17 Jul 2009 21:13:01 +0000 (22:13 +0100)]
ASoC: Fix FLL reference clock division setup in WM8993
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 17 Jul 2009 20:53:49 +0000 (21:53 +0100)]
ASoC: Bodge around GCC 4.4.0 flow analysis bug in GCC 4.4.0
GCC 4.4.0 doesn't appear to be able to spot that we don't apply any FLL
configuration if the output frequency is zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Candelaria Villareal, Jorge [Wed, 15 Jul 2009 01:04:08 +0000 (20:04 -0500)]
ASoC: SDP3430: Add support for EXTMUTE using TWL GPIO6
Board sdp3430 has hardware support for EXTMUTE using TWL4030 GPIO6
line, controlled by register INTBR_PMBR1. Machine driver takes care
of enabling gpio line through i2c and codec driver manipulates the
line during headset ramp up/down sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Fri, 17 Jul 2009 05:48:03 +0000 (07:48 +0200)]
ASoC: Kill direct accesses to driver_data
Replaced with dev_{get|set}_drvdata().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Barry Song [Thu, 16 Jul 2009 08:00:05 +0000 (16:00 +0800)]
ASoC: new ad1938 codec driver based on asoc
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kevin Hilman [Wed, 15 Jul 2009 17:42:09 +0000 (10:42 -0700)]
ASoC: davinci: don't use clock names
clock name strings are no longer passed on platform_data. Instead,
we rely entirely on struct device and clkdev to find the right clock.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Joonyoung Shim [Wed, 15 Jul 2009 11:34:00 +0000 (20:34 +0900)]
ASoC: MAX9877: add MAX9877 amp driver
The MAX9877 combines a high-efficiency Class D audio power amplifier
with a stereo Class AB capacitor-less DirectDrive headphone amplifier.
The max9877_add_controls() is called to register the MAX9877 specific
controls on machine specific init() of the machine driver.
The datasheet for the MAX9877 can find at the following url:
http://datasheets.maxim-ic.com/en/ds/MAX9877.pdf
[Slight edit to sort the ALL_CODECS entries -- broonie.]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Joonyoung Shim [Wed, 15 Jul 2009 11:33:50 +0000 (20:33 +0900)]
ASoC: add SOC_DOUBLE_R_EXT_TLV control type
This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_R_EXT_TLV needs two registers and one shift for
double controls.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Joonyoung Shim [Wed, 15 Jul 2009 11:33:47 +0000 (20:33 +0900)]
ASoC: add SOC_DOUBLE_EXT_TLV control type
This is a macro for double controls with special callback function and
TLV. The SOC_DOUBLE_EXT_TLV needs one register and two shifts for double
controls.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 15 Jul 2009 09:36:51 +0000 (10:36 +0100)]
ASoC: Error out if we can't determine a suitable WM9081 sysclk
Due to the flexibility of the WM9081 FLL this should never happen
in a real system.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 15 Jul 2009 09:01:30 +0000 (10:01 +0100)]
ASoC: Fix sample rate lookup in WM8993
We need to use the best value we picked, not the last value we
looked at.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cliff Cai [Tue, 14 Jul 2009 14:01:40 +0000 (10:01 -0400)]
ASoC: Blackfin I2S: fix resume handling
There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cliff Cai [Tue, 14 Jul 2009 14:01:39 +0000 (10:01 -0400)]
ASoC: Blackfin AC97: fix resume handling
There is no need to manually start playback/capture ourselves as the PCM
driver will handle things for us.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 13 Jul 2009 22:05:51 +0000 (23:05 +0100)]
Merge branch 'for-2.6.31' into for-2.6.32
Peter Meerwald [Mon, 13 Jul 2009 22:05:11 +0000 (23:05 +0100)]
ASoC: fixes multiple typos in comments, no functional change
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kevin Hilman [Mon, 13 Jul 2009 21:50:40 +0000 (14:50 -0700)]
ASoC: spdif: set module licence to GPL
Without MODULE_LICENCE("GPL"), when built as a module it will fail
to load because it uses other GPL symbols from kernel.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kevin Hilman [Mon, 13 Jul 2009 21:50:39 +0000 (14:50 -0700)]
ASoC: spdif codec: enable use by modules
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rongrong Cao [Fri, 10 Jul 2009 19:13:30 +0000 (20:13 +0100)]
ASoC: fix checking for external widgets bug
In SOC DAPM layer of SOUND subsystem, when add signal route (in the
function snd_soc_dapm_add_route() ), the original code has wrong logic
when dapm layer check each widget whether an external one.
Signed-off-by: Rongrong Cao <rrcao@ambarella.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Roel Kluin [Mon, 13 Jul 2009 00:20:10 +0000 (02:20 +0200)]
ASoC: Keep index within stac9766_reg[]
Keep index within stac9766_reg[]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Thu, 9 Jul 2009 10:28:07 +0000 (11:28 +0100)]
ASoC: WM8510 has a single frame clock so needs symmetric rates
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Mack [Wed, 8 Jul 2009 17:24:26 +0000 (19:24 +0200)]
ASoC: Fix NULL pointer dereference in __pxa2xx_pcm_hw_free
Check for rtd->params->drcmr != NULL before accessing it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 17:54:57 +0000 (18:54 +0100)]
ASoC: Add pop delay debug at end of DAPM sequencing
Provide an interval after the end of DAPM sequencing so that we
can distinguish between a pop in the final step of the sequence
and a pop generated from some other source outside DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 17:26:16 +0000 (18:26 +0100)]
ASoC: Configure WM8731 SYSCLK at startup on AT91SAM9G20-EK
The system clock is currently fixed by the driver and this avoids
the need for us to handle errors with enabling and disabling MCLK
(which was incorrect previously so this fixes bugs in error
handling).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 17:18:19 +0000 (18:18 +0100)]
ASoC: Disable microphone input for AT91SAM9G20-EK by default
As shipped the board does not have inputs but it is relatively
straightforward to modify the board to hook them up so support
is provided in the driver. When these modifications have not
been made enabling the microphone stage can cause problems.
Add an ifdef to disable this by default. Don't put it into
Kconfig since users will have to get their soldering irons
out to change things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 17:05:51 +0000 (18:05 +0100)]
ASoC: Use CODEC as clock master on AT91SAM9G20-EK
This simplifies the driver by removing the need to manually
configure dividers within the CPU and improve audio performance
by ensuring that the optimal phase relationships between the
clocks in the system are maintained.
Note that currently this means that for playback to work the
Output Mixer HiFi switch must be enabled since otherwise CODEC
will not generate the DAC clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 16:48:12 +0000 (17:48 +0100)]
ASoC: Limit WM8731 to symmetric rates
While the hardware is capable of some limited asynmmetric modes the
driver does not currently support those modes so tell applications
that only symmetric rates are available.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 5 Jun 2009 15:32:59 +0000 (16:32 +0100)]
ASoC: Add WM8993 CODEC driver
The WM8993 is a highly integrated ultra-low power hi-fi CODEC designed
for portable devices such as multimedia phones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 15:54:51 +0000 (16:54 +0100)]
ASoC: DaVinci I2S needs mach/asp.h
Reported-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 16:05:43 +0000 (17:05 +0100)]
ASoC: Correct WM8731 Mic Capture Switch control name
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 8 Jul 2009 15:53:12 +0000 (16:53 +0100)]
ASoC: Add TLV information for WM8731
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Wed, 8 Jul 2009 00:36:06 +0000 (17:36 -0700)]
ASoC: DaVinci: pcm, don't play 1st sound period twice
Update the dma link with correct data as soon as
the master channel has copied it. Otherwise, the
1st period will play twice.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 7 Jul 2009 18:18:46 +0000 (19:18 +0100)]
Merge branch 'davinci' into for-2.6.32
Conflicts:
sound/soc/davinci/davinci-i2s.c
Mark Brown [Mon, 6 Jul 2009 20:49:35 +0000 (21:49 +0100)]
Merge branch 'for-2.6.31' into for-2.6.32
Mark Brown [Sun, 5 Jul 2009 16:28:41 +0000 (17:28 +0100)]
ASoC: Remove unused AK4535 hardware read functionality
Nothing uses it and the existing hw_read operation needs to be
refectored so it's easier to remove it rather than work with it.
Support can be re-added if the code requires volatile registers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 5 Jul 2009 15:29:39 +0000 (16:29 +0100)]
ASoC: Fix leaks in WM8988 registration error handling
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 5 Jul 2009 14:47:03 +0000 (15:47 +0100)]
ASoC: Fix WM8960 leaks on probe failure
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 5 Jul 2009 14:18:01 +0000 (15:18 +0100)]
ASoC: Fix leaks in WM8731 probe error handling
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 5 Jul 2009 14:12:22 +0000 (15:12 +0100)]
ASoC: Add CODEC volatile register operation
Add a volatile_register() operation to the CODEC structure providing a
standard operation to query if a register is volatile. This will be used
to factor out the register cache I/O operations for the CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:59 +0000 (19:29 -0700)]
ASoC: DaVinci: i2s, add davinci_i2s_prepare and shutdown
If the codec is master then prepare should call
mcbsp_start, not trigger.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:57 +0000 (19:29 -0700)]
ASoC: DaVinci: i2s, fix mcbsp_word_length update
Code previously just "ors" in this field without clearing
first. Fix, by never reading this register.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:56 +0000 (19:29 -0700)]
ASoC: DaVinci: i2s, minor cleanup of davinci_i2s_startup
Save a few lines of code.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:55 +0000 (19:29 -0700)]
ASoC: DaVinci: i2s, only start sample generator if needed
Only start sample generator if needed, and more
cleanup on davinci_mcbsp_start.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:54 +0000 (19:29 -0700)]
ASoC: DaVinci: i2s cleanup
Move variable declaration closer to use.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:53 +0000 (19:29 -0700)]
ASoc: DaVinci: i2s, minor cleanup
Add davinci_mcbsp_dev as argument to davinci_mcbsp_start
and davinci_mcbsp_stop.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:52 +0000 (19:29 -0700)]
ASoC: DaVinci: i2s toggle clock to complete reset
Add toggle_clock function to complete i2s reset earlier.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Troy Kisky [Sun, 5 Jul 2009 02:29:51 +0000 (19:29 -0700)]
ASoC: DaVinci: i2s, remove MOD_REG_BIT macro
No functional changes. Rename variable w to something
more meaningful. Remove code obfuscating macro MOD_REG_BIT.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lars-Peter Clausen [Thu, 2 Jul 2009 23:04:16 +0000 (01:04 +0200)]
ASoC: Fix wm8753 register cache size and initialization
Register cache space was not being allocated for the final register,
causing bugs when it was used. Allocate space for it.
Also ensure that the final register is displayed in sysfs.
[Commit message rewritten to document actual issue. -- broonie]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lopez Cruz, Misael [Fri, 3 Jul 2009 07:21:39 +0000 (02:21 -0500)]
ASoC: TWL4030: Add tristate callbacks for HiFi and Voice
Add "set_tristate" callbacks for HiFi and Voice DAIs.
Machine drivers can enable and disable tristate for each
DAI with "snd_soc_dai_set_tristate" function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Candelaria Villareal, Jorge [Fri, 3 Jul 2009 00:04:07 +0000 (19:04 -0500)]
ASoC: Zoom2: Update twl4030_setup_data parameters
Add support for EXTMUTE in Zoom2 machine driver. This is necessary
to further reduce pop noise problem. Signal EXTMUTE is connected to
signal GPIO 153 in Zoom2 board.
In addition, change ramp delay value to 3 (218/161/109 ms). With
previous ramp delay value, pop noise was louder. With a longer value
the beep tone can be observed.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Grant Likely [Thu, 2 Jul 2009 17:57:25 +0000 (11:57 -0600)]
ASoC: add locking to mpc5200-psc-ac97 driver
AC97 bus register read/write hooks need to provide locking, but the
mpc5200-psc-ac97 driver does not. This patch adds a mutex around
the register access routines.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Grant Likely [Thu, 2 Jul 2009 17:57:19 +0000 (11:57 -0600)]
ASoC: Fix mpc5200-psc-ac97 to ensure the data ready bit is cleared
When doing register reads, it is possible for there to be a stale
data ready bit set which will cause subsequent reads to return
prematurely with incorrect data. This patch fixes the issues by
ensuring stale data is cleared before starting another transaction.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 3 Jul 2009 09:33:39 +0000 (10:33 +0100)]
ASoC: Fix register cache initialisation for WM8753
The wrong register cache variable was being used to provide the size for
the memcpy(), resulting in a copy of only a void * of data.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Candelaria Villareal, Jorge [Thu, 2 Jul 2009 00:17:43 +0000 (19:17 -0500)]
ASoC: TWL4030: Add EXTMUTE to reduce pop-noise effect
According to TRM, an external FET controlled by a 1.8V output signal
can be used to reduce the pop-noise heard when the audio amplifier is
switched on. It is suggested that GPIO6 of TWL4030 be used, but any
other gpio can be used instead. This is indicated in machine driver
with the following twl4030_setup_data members:
-hs_extmute. Set to 1 if board has support for EXTMUTE.
-set_hs_extmute. Set to a callback funcion to control an external gpio
line. Set to NULL if MUTE[GPIO6] pin is used.
Codec driver takes care of enabling and disabling this output during
the headset pop attenuation sequence.
Also add a delay to let VMID settle in ramp up sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 1 Jul 2009 20:45:47 +0000 (21:45 +0100)]
Merge branch 'for-2.6.31' into for-2.6.32
Mark Brown [Wed, 1 Jul 2009 17:28:54 +0000 (18:28 +0100)]
ASoC: Add WM8523 CODEC driver
The WM8523 is a high performance stereo DAC with integral charge
pump providing 2Vrms line driver outputs using a single 3.3V power
supply rail.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 1 Jul 2009 17:23:26 +0000 (18:23 +0100)]
ASoC: Only disable pxa2xx-i2s clocks if we enabled them
The clock API can't cope with unbalanced enables and disables and
we only enable in hw_params() but try to disable in shutdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 30 Jun 2009 18:05:15 +0000 (19:05 +0100)]
ASoC: Convert to dev_pm_ops
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Janusz Krzysztofik [Sat, 27 Jun 2009 22:21:05 +0000 (00:21 +0200)]
ASoC: OMAP: fix OMAP1510 broken PCM pointer callback
This patch tries to work around the problem of broken OMAP1510 PCM playback
pointer calculation by replacing DMA function call that incorrectly tries to
read the value form DMA hardware with a value computed locally from an
already maintained variable omap_runtime_data.period_index.
Tested on OMAP5910 based Amstrad Delta (E3) using work in progress ASoC
driver.
Based on linux-2.6-asoc.git v2.6.31-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Grant Likely [Sun, 28 Jun 2009 07:42:06 +0000 (01:42 -0600)]
ASoC: remove BROKEN from Efika and pcm030 fabric drivers
The needed spin_event_timeout() macro is now merged in from the
powerpc tree, so these drivers are no longer broken. This reverts
commit
0c0e09e21a9e7bc6ca54e06ef3d497255ca26383 (ASoC: Mark MPC5200
AC97 as BROKEN until PowerPC merge issues are resolved)
Tested against 2.6.31-rc1.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Grant Likely [Sun, 28 Jun 2009 07:41:52 +0000 (01:41 -0600)]
ASoC: Fix typo in MPC5200 PSC AC97 driver Kconfig
ALSA SoC drivers should be specify SND_SOC_AC97_BUS instead, not AC97_BUS.
Without SND_SOC_AC97_BUS defined, an AC97 device will not get correctly
registered on the AC97 bus, which prevents thinks like the WM9712
touchscreen driver from getting probed.
Tested against 2.6.31-rc1.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 29 Jun 2009 15:29:06 +0000 (16:29 +0100)]
ASoC: Fix WM8961 suspend function type
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Fri, 26 Jun 2009 14:36:56 +0000 (15:36 +0100)]
ASoC: Fix widget powerdown on shutdown
We need to set the widget power state we want to implement.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lopez Cruz, Misael [Thu, 25 Jun 2009 17:36:14 +0000 (12:36 -0500)]
ASoC: Remove word "Switch" from Handsfree switch name
SoC dapm adds the suffix "Switch" to SND_SOC_DAPM_SWITCH controls,
removing word "Switch" from HandsfreeL/HandsfreeR widget name
for avoiding to duplicate it.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Atsushi Nemoto [Thu, 25 Jun 2009 13:36:58 +0000 (22:36 +0900)]
ASoC: txx9aclc: dynamically allocate dmaengine devname
Use kasprintf to allocate temporary devname string instead of a
fixed size string.
This fixes "FIXME" introduced on removal of BUS_ID_SIZE.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Thu, 25 Jun 2009 13:28:39 +0000 (15:28 +0200)]
Merge branch 'for-2.6.32' of git://git./linux/kernel/git/broonie/sound-2.6 into topic/asoc
Takashi Iwai [Thu, 25 Jun 2009 13:28:14 +0000 (15:28 +0200)]
Merge branch 'for-2.6.31' of git://git./linux/kernel/git/broonie/sound-2.6 into fix/asoc
Conflicts:
MAINTAINERS
Mark Brown [Thu, 25 Jun 2009 12:58:37 +0000 (13:58 +0100)]
Merge branch 'for-2.6.31' into for-2.6.32
Mark Brown [Thu, 25 Jun 2009 12:57:59 +0000 (13:57 +0100)]
ASoC: Add core suspend and resume callbacks to WM8961
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi [Thu, 25 Jun 2009 10:26:09 +0000 (13:26 +0300)]
MAINTAINERS: Add entry for twl4030 series soc codec driver
New MAINTAINERS entry for twl4030 series soc codec driver
with Peter Ujfalusi as maintainer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Wed, 24 Jun 2009 23:25:37 +0000 (16:25 -0700)]
Linux 2.6.31-rc1
Linus Torvalds [Wed, 24 Jun 2009 23:23:03 +0000 (16:23 -0700)]
Revert "PCI: use ACPI _CRS data by default"
This reverts commit
9e9f46c44e487af0a82eb61b624553e2f7118f5b.
Quoting from the commit message:
"At this point, it seems to solve more problems than it causes, so let's
try using it by default. It's an easy revert if it ends up causing
trouble."
And guess what? The _CRS code causes trouble.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 24 Jun 2009 21:35:57 +0000 (14:35 -0700)]
Merge git://git.infradead.org/battery-2.6
* git://git.infradead.org/battery-2.6:
da9030_battery: Fix race between event handler and monitor
Add MAX17040 Fuel Gauge driver
w1: ds2760_battery: add support for sleep mode feature
w1: ds2760: add support for EEPROM read and write
ds2760_battery: cleanups in ds2760_battery_probe()
Linus Torvalds [Wed, 24 Jun 2009 21:17:14 +0000 (14:17 -0700)]
Merge branches 'for-linus' of git://git./linux/kernel/git/viro/{vfs-2.6,audit-current}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
another race fix in jfs_check_acl()
Get "no acls for this inode" right, fix shmem breakage
inline functions left without protection of ifdef (acl)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
audit: inode watches depend on CONFIG_AUDIT not CONFIG_AUDIT_SYSCALL
Al Viro [Wed, 24 Jun 2009 21:02:42 +0000 (17:02 -0400)]
another race fix in jfs_check_acl()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Wed, 24 Jun 2009 20:58:48 +0000 (16:58 -0400)]
Get "no acls for this inode" right, fix shmem breakage
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Eric Paris [Wed, 24 Jun 2009 20:09:01 +0000 (16:09 -0400)]
audit: inode watches depend on CONFIG_AUDIT not CONFIG_AUDIT_SYSCALL
Even though one cannot make use of the audit watch code without
CONFIG_AUDIT_SYSCALL the spaghetti nature of the audit code means that
the audit rule filtering requires that it at least be compiled.
Thus build the audit_watch code when we build auditfilter like it was
before
cfcad62c74abfef83762dc05a556d21bdf3980a2
Clearly this is a point of potential future cleanup..
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Markus Trippelsdorf [Wed, 24 Jun 2009 20:28:52 +0000 (22:28 +0200)]
inline functions left without protection of ifdef (acl)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Wed, 24 Jun 2009 20:33:19 +0000 (13:33 -0700)]
Merge branch 'futexes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Fix the write access fault problem for real
Thomas Gleixner [Thu, 11 Jun 2009 21:15:43 +0000 (23:15 +0200)]
futex: Fix the write access fault problem for real
commit
64d1304a64 (futex: setup writeable mapping for futex ops which
modify user space data) did address only half of the problem of write
access faults.
The patch was made on two wrong assumptions:
1) access_ok(VERIFY_WRITE,...) would actually check write access.
On x86 it does _NOT_. It's a pure address range check.
2) a RW mapped region can not go away under us.
That's wrong as well. Nobody can prevent another thread to call
mprotect(PROT_READ) on that region where the futex resides. If that
call hits between the get_user_pages_fast() verification and the
actual write access in the atomic region we are toast again.
The solution is to not rely on access_ok and get_user() for any write
access related fault on private and shared futexes. Instead we need to
fault it in with verification of write access.
There is no generic non destructive write mechanism which would fault
the user page in trough a #PF, but as we already know that we will
fault we can as well call get_user_pages() directly and avoid the #PF
overhead.
If get_user_pages() returns -EFAULT we know that we can not fix it
anymore and need to bail out to user space.
Remove a bunch of confusing comments on this issue as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Pekka Enberg [Wed, 24 Jun 2009 18:59:51 +0000 (21:59 +0300)]
SLUB: Don't pass __GFP_FAIL for the initial allocation
SLUB uses higher order allocations by default but falls back to small
orders under memory pressure. Make sure the GFP mask used in the initial
allocation doesn't include __GFP_NOFAIL.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 24 Jun 2009 19:16:49 +0000 (12:16 -0700)]
Don't warn about order-1 allocations with __GFP_NOFAIL
Traditionally, we never failed small orders (even regardless of any
__GFP_NOFAIL flags), and slab will allocate order-1 allocations even for
small allocations that could fit in a single page (in order to avoid
excessive fragmentation).
Maybe we should remove this warning entirely, but before making that
judgement, at least limit it to bigger allocations.
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 24 Jun 2009 17:47:38 +0000 (10:47 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Staging: octeon-ethernet: Fix race freeing transmit buffers.
Staging: octeon-ethernet: Convert to use net_device_ops.
MIPS: Cavium: Add CPU hotplugging code.
MIPS: SMP: Allow suspend and hibernation if CPU hotplug is available
MIPS: Add arch generic CPU hotplug
DMA: txx9dmac: use dma_unmap_single if DMA_COMPL_{SRC,DEST}_UNMAP_SINGLE set
MIPS: Sibyte: Fix build error if CONFIG_SERIAL_SB1250_DUART is undefined.
MIPS: MIPSsim: Fix build error if MSC01E_INT_BASE is undefined.
MIPS: Hibernation: Remove SMP TLB and cacheflushing code.
MIPS: Build fix - include <linux/smp.h> into all smp_processor_id() users.
MIPS: bug.h Build fix - include <linux/compiler.h>.
David Daney [Tue, 23 Jun 2009 23:20:56 +0000 (16:20 -0700)]
Staging: octeon-ethernet: Fix race freeing transmit buffers.
The existing code had the following race:
Thread-1 Thread-2
inc/read in_use
inc/read in_use
inc tx_free_list[qos].len
inc tx_free_list[qos].len
The actual in_use value was incremented twice, but thread-1 is going
to free memory based on its stale value, and will free one too many
times. The result is that memory is freed back to the kernel while
its packet is still in the transmit buffer. If the memory is
overwritten before it is transmitted, the hardware will put a valid
checksum on it and send it out (just like it does with good packets).
If by chance the TCP flags are clobbered but not the addresses or
ports, the result can be a broken TCP stream.
The fix is to track the number of freed packets in a single location
(a Fetch-and-Add Unit register). That way it can never get out of sync
with itself.
We try to free up to MAX_SKB_TO_FREE (currently 10) buffers at a time.
If fewer are available we adjust the free count with the difference.
The action of claiming buffers to free is atomic so two threads cannot
claim the same buffers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 23 Jun 2009 18:34:08 +0000 (11:34 -0700)]
Staging: octeon-ethernet: Convert to use net_device_ops.
Convert the driver to use net_device_ops as it is now mandatory.
Also compensate for the removal of struct sk_buff's dst field.
The changes are mostly mechanical, the content of ethernet-common.c
was moved to ethernet.c and ethernet-common.{c,h} are removed.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 23 Jun 2009 09:36:38 +0000 (10:36 +0100)]
MIPS: Cavium: Add CPU hotplugging code.
Thanks to Cavium Inc. for the code contribution and help.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 23 Jun 2009 09:20:56 +0000 (10:20 +0100)]
MIPS: SMP: Allow suspend and hibernation if CPU hotplug is available
The SMP implementation of suspend and hibernate depends on CPU hotplugging.
In the past we didn't have CPU hotplug so suspend and hibernation were not
possible on SMP systems.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Tue, 23 Jun 2009 09:00:31 +0000 (10:00 +0100)]
MIPS: Add arch generic CPU hotplug
Each platform has to add support for CPU hotplugging itself by providing
suitable definitions for the cpu_disable and cpu_die of the smp_ops
methods and setting SYS_SUPPORTS_HOTPLUG_CPU. A platform should only set
SYS_SUPPORTS_HOTPLUG_CPU once all it's smp_ops definitions have the
necessary changes. This patch contains the changes to the dummy smp_ops
definition for uni-processor systems.
Parts of the code contributed by Cavium Inc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Wed, 17 Jun 2009 20:08:31 +0000 (13:08 -0700)]
DMA: txx9dmac: use dma_unmap_single if DMA_COMPL_{SRC,DEST}_UNMAP_SINGLE set
This patch does not change actual behaviour since dma_unmap_page is just
an alias of dma_unmap_single on MIPS.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Mon, 22 Jun 2009 15:17:52 +0000 (16:17 +0100)]
MIPS: Sibyte: Fix build error if CONFIG_SERIAL_SB1250_DUART is undefined.
This fixes kernel.org bugzilla 13596, see
http://bugzilla.kernel.org/show_bug.cgi?id=13596
Reported-by: dvice_null@yahoo.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Mon, 22 Jun 2009 14:48:27 +0000 (15:48 +0100)]
MIPS: MIPSsim: Fix build error if MSC01E_INT_BASE is undefined.
This fixes kernel.org bugzilla 13595, see
http://bugzilla.kernel.org/show_bug.cgi?id=13595
Reported-by: dvice_null@yahoo.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Fri, 19 Jun 2009 14:01:44 +0000 (15:01 +0100)]
MIPS: Hibernation: Remove SMP TLB and cacheflushing code.
We can't perform any flushes on SMP from swsusp_arch_resume because
interrupts are disabled. A cross-CPU flush is unnecessary anyway
because all but the local CPU have already been disabled. A local
flush is not needed either because we didn't change any mappings. So
just delete the code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Fri, 19 Jun 2009 13:05:26 +0000 (14:05 +0100)]
MIPS: Build fix - include <linux/smp.h> into all smp_processor_id() users.
Some of the were relying into smp.h being dragged in by another header
which of course is fragile. <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This page took 0.044357 seconds and 5 git commands to generate.