Olof Johansson [Sat, 19 Jul 2014 22:06:48 +0000 (15:06 -0700)]
Merge tag 'samsung-dt' of git://git./linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.17" from Kukjin Kim:
exynos3250: add i2s dt for audio interface
exynos4
- cleanup arm-pmu node because of 4 pmu on
exynos4412 but 2 pmu on other exynos4 SoCs
- add support sub-nodes to exynos usb host for exynos4
exynos4412-odroid-common
- fix T-FLASH hotplug detection
- disable 'always on' for BUCK8
- add support for GPIO based buttons
- add MAX98090 audio codec
exynos4412-odroidx2 and exynos4412-odroidu3
- refactor exynos4412-odroidx and exynos4412-odroid-common
for odroid-x2 and u2/u3
exynos4412-odroidx
- add support for USB phy, host and device
- enable common hardware blocks, secure firmware calls,
watchdog, g2d and fimc (mem2mem) multimedia accelerators
- add support for USB phy, host and device
- correct memory size
exynos5410
- fill in CPU clock-frequency property to avoid warning
exynos5420
- remove display pd because of instability
exynos5420-peach-pit and exynos5800-peach-pi
- sort nodes each other to check its differences easily
- enable audio support and add sound-card name property
- add mask-tpm-reset node
- add cros_ec including keyboard, i2c tunnel and tps65090
and battery under the i2c tunnel
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add I2S dt node for exynos3250
ARM: dts: Add cros_ec to exynos5420-peach-pit and exynos5800-peach-pi
ARM: dts: clean up arm-pmu node for exynos4
ARM: dts: remove display power domain for exynos5420
ARM: dts: Add sound nodes for Odroid-X2/U3 boards
ARM: dts: fix T-FLASH hotplug detection for exynos4412-odroid-common
ARM: dts: add support for GPIO buttons for exynos4412-odroid
ARM: dts: disable 'always on' for BUCK8 regulator for exynos4412-odroid-common
ARM: dts: refactor Odroid DTS file and add support for Odroid X2 and U2/U3
ARM: dts: correct memory size for exynos4412-odroidx
ARM: dts: add support for USB phy, host and device for exynos4412-odroidx
ARM: dts: enable common hardware blocks for exynos4412-odroidx
ARM: dts: add port sub-nodes to exynos usb host modules for exynos4
ARM: dts: Add mask-tpm-reset node in exynos5800-peach-pi
ARM: dts: Add mask-tpm-reset node in exynos5420-peach-pit
ARM: dts: Add sound-card name for Snow/Peach-Pit/Peach-Pi
ARM: dts: Fill in CPU clock-frequency for exynos5410
ARM: dts: Sort nodes within Peach-pit/Peach-pi dts files
ARM: dts: Enable audio support for exynos5800-peach-pi
Olof Johansson [Sat, 19 Jul 2014 19:51:26 +0000 (12:51 -0700)]
Merge tag 'tegra-for-3.17-dt' of git://git./linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: device tree changes for 3.17" from Thierry Reding:
- New board support:
* Apalis T30
- HDA support for Tegra124 and Venice2
- Display on Medcom Wide and Roth
- GK20A support on Tegra124
- XUSB pad controller for Tegra124 and Jetson TK1
- Various cleanups
This pulls in the for-3.17/fuse-move, for-3.17/dt-cros-ec-kbd and
for-3.17/xusb-padctl branches to resolve dependencies.
Note that the Apalis T30 support has a runtime dependency on the
for-3.17/pcie-regulators branch, so they should preferably be applied
in that order. I didn't merge that branch into this because Apalis T30
support is new, therefore can't regress, and because the dependency
exists only at runtime.
* tag 'tegra-for-3.17-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (28 commits)
ARM: tegra: roth: add display DT node
ARM: tegra: Fix typoed ams,ext-control properties
ARM: tegra: jetson-tk1: Add XUSB pad controller
ARM: tegra: tegra124: Add XUSB pad controller
ARM: tegra: add GK20A GPU to Tegra124 DT
ARM: tegra: of: add GK20A device tree binding
ARM: tegra: roth: enable input on mmc clock pins
ARM: tegra: roth: fix unsupported pinmux properties
ARM: tegra: Migrate Apalis T30 PCIe power supply scheme
ARM: tegra: tamonten: add the display to the Medcom Wide
ARM: tegra: tamonten: add the base board regulators
ARM: tegra: initial support for apalis t30
ARM: tegra: jetson-tk1: mark eMMC as non-removable
ARM: tegra: venice2 - Enable HDA
ARM: tegra: Add Tegra124 HDA support
ARM: tegra: Add the EC i2c tunnel to tegra124-venice2
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 19 Jul 2014 19:49:24 +0000 (12:49 -0700)]
Merge tag 'tegra-for-3.17-xusb-padctl' of git://git./linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Add XUSB pad controller support" from Thierry Reding:
Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.
This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.
* tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
pinctrl: Add NVIDIA Tegra XUSB pad controller support
of: Add NVIDIA Tegra XUSB pad controller binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 19 Jul 2014 19:19:28 +0000 (12:19 -0700)]
Merge tag 'sunxi-dt-for-3.17' of git://git./linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT additions for 3.17" from Maxime Ripard:
Among the few patches that we have so far, there's a few noticeable changes:
- Introduction of the Allwinner A23 SoC
- Support for the GMAC on the A31. This is only available so far on the
boards which bootloader enable the PHY regulator.
- Addition of the infrared receiver
* tag 'sunxi-dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (22 commits)
ARM: dts: sun6i: Add Merrii A31 Hummingbird support
ARM: dts: sun6i: Add ethernet alias for GMAC
ARM: dts: sun6i: Add A31 GMAC gigabit ethernet controller node
ARM: dts: sun6i: Add GMAC clock node to the A31 dtsi
ARM: dts: sun6i: Add pin muxing options for GMAC
ARM: sun8i: Add PRCM clock and reset controller nodes to the DTSI
ARM: sun8i: Add reset controller nodes to the DTSI
ARM: sun8i: Add basic clock nodes to the DTSI
ARM: dts: sun4i: Add ir node to various boards
ARM: dts: sun4i: Add ir controller nodes and pinmux
ARM: dts: sun4i: Add new ba10-tvbox board
ARM: dts: sun7i: Add board support for LinkSprite pcDuino V3
ARM: dts: sun7i: Add ir receiver support to a20-i12-tvbox
ARM: dts: sun7i: Rename sun7i-a20-ir to sun4i-a10-ir
ARM: dts: sun7i: Add AXP209 support to various boards
ARM: dts: sun4i: Add AXP209 support to various boards
ARM: dts: sunxi: Add #interrupt-cells to pinctrl nodes
ARM: sun8i: dt: Add Ippo-q8h v5 support
ARM: sunxi: Add Allwinner A23 dtsi
ARM: sunxi: Add IR controllers on A20 to dtsi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 19 Jul 2014 19:16:02 +0000 (12:16 -0700)]
Merge tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx into next/dt
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 19 Jul 2014 19:12:57 +0000 (12:12 -0700)]
Merge tag 'imx-dt-3.17' of git://git./linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree updates for 3.17" from Shawn Guo:
The i.MX device tree updates for 3.17:
- Add device tree sources and pin function header for i.MX6SX SoC
- Initial imx6sx-sdb board support with FEC, MMC, USB, PMIC, Audio
and GPIO key enabled
- New board support: mbimxsd25 and mbimxsd27 from Eukrea, aristainetos
imx6dl boards, Rex Pro and Basic, Ka-Ro TX6
- Restructure imx6qdl-wandboard.dtsi for new rev C1 board
- Split M28EVK and M53EVK into SoM and EVK parts
- A few correction around SDMA, SSI and SATA device nodes
- Add eSATA support for Cubox-i board
- Updates on edmqmx6 to enable PCIe, I2C and CAN
- Use DT macro for clock ID for imx27 and imx6qdl
- Add FlexCAN support for VF610 SoC
* tag 'imx-dt-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (125 commits)
ARM: dts: vf610: add FlexCAN node
ARM: dts: add initial Rex Basic board support
ARM: dts: add initial Rex Pro board support
ARM: dts: mx5: Split M53EVK into SoM and EVK parts
ARM: dts: imx6: RIoTboard explicitly define pad settings
ARM: dts: vf610: fix length of eshdc1 register property
ARM: dts: Restructure imx6qdl-wandboard.dtsi for new rev C1 board.
ARM: dts: imx53: correct clock-names of SATA node
ARM: imx6: Align ssi nodes between mx6 variants
ARM: i.MX27 clk: dts: Use clock defines in DTS files
ARM: dts: imx: correct sdma compatbile for imx6sl and imx6sx
ARM: dts: imx6sx-sdb: Add audio support
ARM: dts: imx6sx: Pass the fsl,fifo-depth property
ARM: dts: imx6sx: Fix sdma node
ARM: dts: imx6: edmqmx6: Add can bus
ARM: dts: imx6: edmqmx6: Add two other i2c buses
ARM: dts: imx6: edmqmx6: Add PCIe support
ARM: dts: imx25-pdk: Add USB OTG support
ARM: dts: i.MX53: add aipstz nodes
ARM: dts: mxs: Split M28EVK into SoM and EVK parts
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 19 Jul 2014 18:49:16 +0000 (11:49 -0700)]
Merge tag 'keystone-dts' of git://git./linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "Keystone DTS update for 3.17" from Santosh Shilimkar:
Keystone DTS update for 3.17
- Ethernet clock tree fix.
- MDIO device tree node. Respective driver update is already queued.
- Ethernet phy node. Respective driver update is already queued.
* tag 'keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-evm: add 1g ethernet phys nodes
ARM: dts: keystone: add mdio devices entries
ARM: dts: keystone: fix netcp's clocks definitions
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 19 Jul 2014 05:16:15 +0000 (22:16 -0700)]
Merge tag 'omap-for-v3.17/dt-part1' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v3.17 merge window, part1" from Tony Lindgren:
First set of .dts changes for omaps for v3.17 merge window:
- Enable irqchip crossbar interrupt mapping. These changes
are based on an immutable irqchip branch set up by Jason
Cooper to make it easier to merge the related .dts changes.
- Removal of omap2 related static clock data that now comes
from device tree.
- Enabling of PHY regulators for various omaps
- Enabling of PCIe for dra7
- Add support for am437x starterkit
- Enable audio for for omap5
- Enable display and am335x-evmsk
* tag 'omap-for-v3.17/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (43 commits)
ARM: DTS: omap5-uevm: Enable basic audio (McPDM <-> twl6040)
ARM: DTS: omap5-uevm: Add node for twl6040 audio codec
ARM: DTS: omap5-uevm: Enable palmas clk32kgaudio clock
ARM: dts: dra7: Add dt data for PCIe controller
ARM: dts: dra7: Add dt data for PCIe PHY
ARM: dts: dra7: Add dt data for PCIe PHY control module
ARM: dts: dra7xx-clocks: Add missing clocks for second PCIe PHY instance
ARM: dts: dra7xx-clocks: rename pcie clocks to accommodate second PHY instance
ARM: dts: dra7xx-clocks: Add missing 32KHz clocks used for PHY
ARM: dts: dra7xx-clocks: Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
ARM: dts: dra7xx-clocks: Add divider table to optfclk_pciephy_div clock
ARM: dts: dra7-evm: Add regulator information to USB2 PHYs
ARM: omap2plus_defconfig: enable TPS65218 configs
ARM: dts: AM437x: Add TPS65218 device tree nodes
ARM: dts: AM437x: Fix i2c nodes indentation
ARM: dts: AM43x: Add TPS65218 device tree nodes
ARM: dts: Add devicetree for Gumstix Pepper board
ARM: dts: dra7: add crossbar device binding
ARM: dts: dra7: add routable-irqs property for gic node
ARM: OMAP24xx: clock: remove legacy clock data
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 19 Jul 2014 04:39:29 +0000 (21:39 -0700)]
Merge tag 'renesas-dt3-for-v3.17' of git://git./linux/kernel/git/horms/renesas into next/dt
Merge "Third Round of Renesas ARM Based SoC DT Updates for v3.17" from Simon
Horman:
* Initialise SCI using DT when booting the kzm9g, armadillo800eva,
ape6evm and bockw boards without legacy-C code.
* tag 'renesas-dt3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (24 commits)
ARM: shmobile: kzm9g-reference: Initialise SCIF device using DT
ARM: shmobile: sh73a0: Add SCIF nodes
ARM: shmobile: armadillo800eva-reference: Initialise SCIF device using DT
ARM: shmobile: r8a7740: Add SCIF nodes
ARM: shmobile: ape6evm-reference: Initialise SCIF device using DT
ARM: shmobile: r8a73a4: Add SCIF nodes
ARM: shmobile: bockw-reference: Initialise SCIF device using DT
ARM: shmobile: r8a7778: Add SCIF nodes
ARM: shmobile: sh73a0: add SCI clock support for DT
ARM: shmobile: r8a7740: correct SCI clock support for DT
ARM: shmobile: r8a73a4: add SCI clock support for DT
ARM: shmobile: r8a7778: add SCI clock support for DT
ARM: shmobile: r8a7790: lager: use iic cores instead of i2c
ARM: shmobile: Lager: Correct I2C bus for VDD MPU regulator
ARM: shmobile: kzm9g-reference: Remove early_printk from command line
ARM: shmobile: armadillo800eva-reference: Remove early_printk from command line
ARM: shmobile: r8a7779: Consistently use tabs for indentation
ARM: shmobile: henninger: Consistently use tabs for indentation
ARM: shmobile: henninger: enable internal PCI
ARM: shmobile: koelsch: enable internal PCI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Maxime Ripard [Tue, 15 Jul 2014 17:15:47 +0000 (01:15 +0800)]
ARM: dts: sun6i: Add Merrii A31 Hummingbird support
This adds support for the A31 Hummingbird:
http://www.merrii.com/en/pla_d.asp?id=172
The Merrii A31 Hummingbird is a development board based on the
Allwinner A31 SoC with multiple USB ports through a USB hub chip,
a uSD slot, a 10/100/1000M ethernet port, an AP6210 WiFi/BT chip,
TV-in, HDMI, VGA, audio in/out ports, and LCD/CSI headers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: enable usbphy, ehci0, ohci0 for on-board usb hub;
add pcf8563 rtc node; add comments for i2c0 and mmc0 pull-ups;
correct ethernet phy address to 0x01; drop uart2 (BT chip has
no power) and uart3 (no device); use proper commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Chen-Yu Tsai [Tue, 15 Jul 2014 17:15:46 +0000 (01:15 +0800)]
ARM: dts: sun6i: Add ethernet alias for GMAC
Alias GMAC as ethernet0 so U-boot can fill in the MAC address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 15 Jul 2014 17:15:45 +0000 (01:15 +0800)]
ARM: dts: sun6i: Add A31 GMAC gigabit ethernet controller node
The A31 has the same GMAC found on the A20 SoC, except it has
an extra reset control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 15 Jul 2014 17:15:44 +0000 (01:15 +0800)]
ARM: dts: sun6i: Add GMAC clock node to the A31 dtsi
The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai [Tue, 15 Jul 2014 17:15:43 +0000 (01:15 +0800)]
ARM: dts: sun6i: Add pin muxing options for GMAC
The A31 SoC has a GMAC gigabit ethernet controller supporting
MII, GMII, RGMII modes. Add pin muxing options for these modes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tomasz Figa [Fri, 18 Jul 2014 19:10:44 +0000 (04:10 +0900)]
ARM: dts: Add I2S dt node for exynos3250
This patch add I2S (Inter-IC Sound) dt node which supports 1-port
stereo (1 channels) IIS-bus for audio interface with DMA-based
operation.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Tested-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Doug Anderson [Fri, 18 Jul 2014 19:09:15 +0000 (04:09 +0900)]
ARM: dts: Add cros_ec to exynos5420-peach-pit and exynos5800-peach-pi
This adds cros_ec to exynos5420-peach-pit and exynos5800-peach-pi,
including:
* The keyboard
* The i2c tunnel
* The tps65090 under the i2c tunnel
* The battery under the i2c tunnel
To add extra motivation, it should be noted that tps65090 is one of
the things needed to get display-related FETs turned on for pit and
pi.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Chanho Park [Fri, 18 Jul 2014 18:11:48 +0000 (03:11 +0900)]
ARM: dts: clean up arm-pmu node for exynos4
This patch cleans a arm-pmu node up for exynos4. Only exynos4412 series
boards have four pmu interrupts. Rest of exynos4 boards, except 4412, have only
two pmu interrupts. Thus, we can define two interrupts in the
exynos4.dtsi and extends the interrupts only exynos4412.dtsi.
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Soren Brinkmann [Sat, 5 Apr 2014 00:23:45 +0000 (17:23 -0700)]
ARM: zynq: DT: Migrate UART to Cadence binding
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Soren Brinkmann [Sat, 5 Apr 2014 00:23:44 +0000 (17:23 -0700)]
tty: cadence: Document DT binding
Add binding documentation for the Cadence UART.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Stefan Agner [Wed, 16 Jul 2014 06:08:49 +0000 (14:08 +0800)]
ARM: dts: vf610: add FlexCAN node
Add FlexCAN node for the two FlexCAN IP instances in Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Robert Nelson [Tue, 8 Jul 2014 14:49:23 +0000 (09:49 -0500)]
ARM: dts: add initial Rex Basic board support
Add initial Rex Pro i.mx6dl board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with
cat zImage imx6dl-rex-basic.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Robert Nelson [Tue, 8 Jul 2014 14:49:22 +0000 (09:49 -0500)]
ARM: dts: add initial Rex Pro board support
Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working. Currently no mainline u-boot, so boot with
cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Marek Vasut [Wed, 25 Jun 2014 18:48:32 +0000 (20:48 +0200)]
ARM: dts: mx5: Split M53EVK into SoM and EVK parts
This patch splits the M53EVK device tree file into a common SoM
part and an EVK part. This is needed to make it easier for users
of the SoM to put it into different, non-reference baseboard.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Iain Paton [Sun, 13 Jul 2014 15:56:35 +0000 (16:56 +0100)]
ARM: dts: imx6: RIoTboard explicitly define pad settings
Instead of relying on defaults or bootloader settings, explicitly define
all pad settings.
This resolves reported issues of no analogue audio output.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Mon, 14 Jul 2014 07:18:46 +0000 (09:18 +0200)]
ARM: dts: vf610: fix length of eshdc1 register property
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
George Joseph [Tue, 8 Jul 2014 18:48:16 +0000 (12:48 -0600)]
ARM: dts: Restructure imx6qdl-wandboard.dtsi for new rev C1 board.
The rev C1 Wandboard uses the Broadcom 4330 for WiFi and Bluetooth instead of
the 4329. This changes the PADS assigned for the control lines. Another
side effect of the change is that on the rev C1 board, usdhc driver can't
detect the chip presence correctly so usdhc2 now needs its 'non-removeable'
property removed.
So that rev B1 and earlier can continue to work, this patch splits the
board-specific definitions from imx6qdl-wandboard.dtsi into
imx6qdl-wandboard-revb1.dtsi and imx6qdl-wandboard-revc1.dtsi. The new files
include the original base imx6qdl-wandboard.dtsi which retains the common
definitions.
The existing imx6dl-wandboard.dts includes imx6qdl-wandboard-revc1.dtsi and
imx6dl-wandboard-revb1.dts (new) includes imx6qdl-wandboard-revb1.dtsi.
This makes the rev C1 board the new default. The same pattern is used for
imx6q-wandboard.dts.
So, from U-Boot on a WB-Quad you use imxq-wandboard-revb1.dtb for the older B1
board and imxq-wandboard.dtb for the current rev C1 board.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 8 Jul 2014 08:14:47 +0000 (16:14 +0800)]
ARM: dts: imx53: correct clock-names of SATA node
Per the binding doc imx-sata.txt, the first entry of clock-names should
be "sata" than anything else. Correct it for imx53 SATA node.
It works for now only because SATA driver gets clock by index so far.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Mon, 7 Jul 2014 13:04:52 +0000 (10:04 -0300)]
ARM: imx6: Align ssi nodes between mx6 variants
Since commit
98ea6ad2edd2 (ARM: dts: imx6: use imx51-ssi) the mx6 ssi is
compatible with imx51, so align all the mx6 variant ssi compatible strings as:
compatible = "fsl,<imx6-soc>-ssi", "fsl,imx51-ssi";
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:36:07 +0000 (09:36 +0400)]
ARM: i.MX27 clk: dts: Use clock defines in DTS files
Use clock definitions in i.MX27 DTS files.
Additional changes included in this patch (imx27.dtsi):
- Fix IPG clock for UART6.
- Use EMI_AHB_GATE clock for WEIM.
- Added GPIO_IPG_GATE clock for GPIO nodes. Currently this clock is
not used by the driver, but it can be added in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Fri, 4 Jul 2014 06:30:27 +0000 (14:30 +0800)]
ARM: dts: imx: correct sdma compatbile for imx6sl and imx6sx
The SDMA on imx6sl and imx6sx is more compatible with imx6q one than
imx35. Let's use "fsl,imx6q-sdma" instead of "fsl,imx35-sdma", so that
SDMA ROM script on imx6sl and imx6sx can work for audio driver just like
the case of imx6q.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Robin Gong <yibin.gong@freescale.com>
Fabio Estevam [Wed, 2 Jul 2014 14:58:52 +0000 (11:58 -0300)]
ARM: dts: imx6sx-sdb: Add audio support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 2 Jul 2014 14:58:50 +0000 (11:58 -0300)]
ARM: dts: imx6sx: Pass the fsl,fifo-depth property
Like the other mx6 variants, we need to pass fsl,fifo-depth property in dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 2 Jul 2014 14:58:49 +0000 (11:58 -0300)]
ARM: dts: imx6sx: Fix sdma node
Use the correct compatible string for sdma and also provide the sdma firmware
path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Tue, 1 Jul 2014 11:09:01 +0000 (13:09 +0200)]
ARM: dts: imx6: edmqmx6: Add can bus
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Tue, 1 Jul 2014 11:09:00 +0000 (13:09 +0200)]
ARM: dts: imx6: edmqmx6: Add two other i2c buses
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Tue, 1 Jul 2014 11:08:59 +0000 (13:08 +0200)]
ARM: dts: imx6: edmqmx6: Add PCIe support
Add support for the PCI express bus available on MX6 Data Modul
edm-qmx6 board.
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 25 Jun 2014 20:28:52 +0000 (17:28 -0300)]
ARM: dts: imx25-pdk: Add USB OTG support
Tested by loading the g_ether module and doing a ping between mx25pdk and the
host PC via USB.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Steffen Trumtrar [Wed, 25 Jun 2014 11:01:30 +0000 (13:01 +0200)]
ARM: dts: i.MX53: add aipstz nodes
The AHB to IP bridges (AIPSTZ) allow fine grained access rights management.
Add both bridges to the DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Marek Vasut [Wed, 25 Jun 2014 18:48:33 +0000 (20:48 +0200)]
ARM: dts: mxs: Split M28EVK into SoM and EVK parts
This patch splits the M28EVK device tree file into a common SoM
part and an EVK part. This is needed to make it easier for users
of the SoM to put it into different, non-reference baseboard.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Denis Carikli [Wed, 25 Jun 2014 12:41:35 +0000 (14:41 +0200)]
ARM: dts: i.MX25: Fix gpt timers clocks.
Without that fix, the board freeze during boot.
This appeared after the following commit:
496f065 ARM: i.MX: Use of_clk_get_by_name() for timer clocks for DT case.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 25 Jun 2014 00:13:44 +0000 (21:13 -0300)]
ARM: dts: mx6: Disable the keypad in the dtsi files
When booting a board that does not have a keypad (such as imx6q-sabresd) the
following error is seen on boot:
imx-keypad
20b8000.kpp: OF: linux,keymap property not defined in /soc/aips-bus@
02000000/kpp@
020b8000
imx-keypad
20b8000.kpp: failed to build keymap
imx-keypad: probe of
20b8000.kpp failed with error -2
Let's disable the keypad functionality in the dtsi files and let each board dts
enable it when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Russell King [Tue, 24 Jun 2014 10:20:03 +0000 (11:20 +0100)]
ARM: dts: cubox-i: disable spread-spectrum for Cubox-i eSATA
Spread-spectrum doesn't work with Cubox-i hardware. eSATA devices are
detected, but then fail on normal IO. Therefore, disable this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Russell King [Tue, 24 Jun 2014 10:19:58 +0000 (11:19 +0100)]
ARM: dts: cubox-i: add eSATA DT configuration
Add the transmit level, boost and attenuation parameters necessary for
the eSATA interface on Cubox-i to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Mon, 23 Jun 2014 14:21:06 +0000 (11:21 -0300)]
ARM: dts: imx6sx-sdb: Add PMIC support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Mon, 23 Jun 2014 14:21:05 +0000 (11:21 -0300)]
ARM: dts: imx6sx-sdb: Add USB support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Mon, 23 Jun 2014 14:21:04 +0000 (11:21 -0300)]
ARM: dts: imx6sx: Fix usbmisc compatible string
Fix usbmisc compatible string so that usbmisc node can be found and USB
functionality can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anson Huang [Mon, 23 Jun 2014 06:04:01 +0000 (14:04 +0800)]
ARM: dts: imx6sx: iomux-gpr syscon is compatible to imx6q
The imx6sx iomuxc-gpr syscon is compatible to imx6q, so let's add
compatible string 'fsl,imx6q-iomuxc-gpr' for imx6sx iomuxc-gpr syscon node.
This is necessary to enable SW workaround for ERR007265,
please refer to imx6_pm_common_init of arch/arm/mach-imx/pm-imx6.c
for detail.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Sun, 15 Jun 2014 12:36:50 +0000 (20:36 +0800)]
ARM: dts: imx6qdl: use DT macro for clock ID
Switch to use DT macro for clock ID, so that device tree source is more
readable.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anson Huang [Fri, 20 Jun 2014 05:17:29 +0000 (13:17 +0800)]
ARM: dts: imx6sx-sdb: add gpio key support
This patch adds support for imx6sx-sdb board's gpio keys:
SW4(FUNC1): KEY_VOLUMEUP
SW5(FUNC2): KEY_VOLUMEDOWN
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Heiko Schocher [Fri, 20 Jun 2014 14:52:47 +0000 (16:52 +0200)]
ARM: dts: imx6: add aristainetos board support
This patch add support for the imx6dl based aristainetos board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
DRAM: 1 GiB
NAND: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
As this board can used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Denis Carikli [Tue, 17 Jun 2014 10:46:37 +0000 (12:46 +0200)]
ARM: dts: mbimxsd25: cmo-qvga: Fix lcd regulator
The fixed-regulator's enable-active-high property
is needed to indicate that the GPIO regulator is
active high.
Before that the regulator state was inverted.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Markus Pargmann [Tue, 17 Jun 2014 09:06:33 +0000 (11:06 +0200)]
ARM: dts: imx: remove ssi fsl,mode for audio cards
The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.
With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Markus Pargmann [Tue, 17 Jun 2014 09:06:32 +0000 (11:06 +0200)]
ARM: dts: imx6qdl: remove fsl,ssi-dma-events
All dtsi files where already moved to generic dma bindings. Remove the
old non-generic DMA properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Markus Pargmann [Tue, 17 Jun 2014 09:06:31 +0000 (11:06 +0200)]
ARM: dts: imx5: remove fsl,ssi-dma-events
All imx5*.dtsi files define the generic dma bindings. Drop the old
non-generic fsl,ssi-dma-events.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Markus Pargmann [Tue, 17 Jun 2014 09:06:30 +0000 (11:06 +0200)]
ARM: dts: imx50: add ssi dma properties
Replace old ssi dma properties by the generic dma properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Tue, 17 Jun 2014 04:07:35 +0000 (01:07 -0300)]
ARM: dts: imx6sx: Use "vddarm" as the regulator name
The other i.mx6 variants use "vddarm" as the name of the internal regulator
that powers the core. Use the same convention here for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anssi Hannula [Sun, 15 Jun 2014 23:39:45 +0000 (02:39 +0300)]
ARM: dts: imx6: remove non-working spdif rxtx4 and rxtx6 clocks
The S/PDIF rxtx4 and rxtx6 clock inputs are "ESAI_HCKT" and "MLB clock",
respectively, according to the SoC documentation, and they are currently
mapped to clocks "esai" and "mlb".
However, they do not seem to actually work correctly. Testing on a
Cubox-i system with fsl_spdif driver forced to select one of those as
input will result in I/O errors on audio playback, which I believe means
missing clock signal.
Possibly the "ESAI_HCKT" and "MLB clock" refer to some other clocks
related to ESAI and MLB, or we are missing something else.
Since audio playback will not work if fsl_spdif selects these clocks
(which happens rarely), set the inputs do dummy clocks, at least for
now.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anssi Hannula [Sun, 15 Jun 2014 23:39:44 +0000 (02:39 +0300)]
ARM: dts: imx6: remove wrong spdif rxtx2 clock
The rxtx2 clock of i.MX6 S/PDIF is currently set to "asrc" clock.
However, according to SoC documentation, rxtx2 is connected to
ASRC_EXT_CLK, a different external clock.
Testing on Cubox-i system seems to confirm that: when fsl_spdif is
forced to select rxtx2 as input clock, audio playback fails with an I/O
error.
Set rxtx2 to the dummy clock by default to prevent fsl_spdif from
selecting it.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lothar Waßmann [Thu, 12 Jun 2014 13:05:17 +0000 (15:05 +0200)]
ARM: dts: imx6: add support for Ka-Ro TX6 modules
This patch adds support for the Ka-Ro electronics GmbH TX6 modules.
There are five distinct module types with either i.MX6Q or i.MX6DL and
LVDS or LCD display interface and one DTS file for a complete system
with an i.MX6DL based TX6 module and a baseboard mounted on the back
of a display (imx6dl-tx6dl-comtft.dts).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 7 Jun 2014 12:34:18 +0000 (16:34 +0400)]
ARM: dts: i.MX35: Add GPT node
This patch adds the missing (General Purpose Timer) GPT devicetree node
for i.MX35 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lothar Waßmann [Fri, 6 Jun 2014 11:02:59 +0000 (13:02 +0200)]
ARM: dts: imx6: add missing compatible and clock properties for kpp
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Mon, 2 Jun 2014 22:56:21 +0000 (19:56 -0300)]
ARM: dts: imx6q-udoo: Add USB Host support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Denis Carikli [Thu, 22 May 2014 14:00:43 +0000 (16:00 +0200)]
ARM: dts: imx25: mbimxsd25: Add displays support.
The CMO-QVGA, DVI-VGA and DVI-SVGA displays were added.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Philipp Zabel [Tue, 27 May 2014 15:26:37 +0000 (17:26 +0200)]
ARM: dts: imx6qdl: Add CSI device tree port nodes for IPU1 and IPU2
This patch adds CSI subnodes for IPU1 and IPU2 that will contain
ports and endpoints connecting to external elements in the video
pipeline.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Philipp Zabel [Mon, 26 May 2014 12:42:56 +0000 (14:42 +0200)]
ARM: dts: pfla02: Add ethernet phy supply regulator
The 2.5V VDD_ETH_IO voltage supplied by the DA9063 LDO4 is used
to power the KSZ9031 PHY DVDDH input and to pull the necessary
pins (including bootstrap pins) high.
It also powers the i.MX6 NVCC_RGMII and NVCC_ENET inputs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Thu, 22 May 2014 17:45:05 +0000 (14:45 -0300)]
ARM: dts: imx51-babbage: Add PMIC RTC support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tim Harvey [Thu, 22 May 2014 06:04:55 +0000 (23:04 -0700)]
ARM: dts: imx6: ventana: update model to reflect Dual/Solo CPU types
The imx6dl dts supports both DualLite and Solo CPU variants
The imx6q dts supports both Dual and Quad CPU variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tim Harvey [Thu, 22 May 2014 06:04:54 +0000 (23:04 -0700)]
ARM: dts: imx6: ventana: change sound device name
The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common and
not baseboard specific.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexandre Belloni [Thu, 15 May 2014 15:12:48 +0000 (17:12 +0200)]
ARM: dt: imx28-
cfa10036: introduce a regulator for mmc0
The PWM3 pinmux configuration conflicts with gpio 3.28. Introduce a regulator
for mmc0 so that it conflicts with the pwm driver and fails gracefully. The
kernel will then able to access mmc0 normally.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fugang Duan [Tue, 20 May 2014 06:50:44 +0000 (14:50 +0800)]
ARM: dts: imx6sl: add fec sleep pinctrl for pin PM state
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 14 May 2014 19:53:55 +0000 (16:53 -0300)]
ARM: dts: imx6qdl-sabresd: Configure the ECSPI1 chip select pin
GPIO4_9 is used as ECSPI1 chip select and it needs to be configured as GPIO.
Configure the pin functionality explicitly in the dts file instead of relying
on the fact that it comes configured as GPIO from POR or from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Tue, 13 May 2014 14:48:15 +0000 (18:48 +0400)]
ARM: dts: Add support for the cpuimx27 board from Eukrea and its baseboard
This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 13 May 2014 13:43:36 +0000 (21:43 +0800)]
ARM: dts: imx: add initial imx6sx-sdb board support
Add initial imx6sx-sdb board support with limited devices enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 13 May 2014 12:21:35 +0000 (20:21 +0800)]
ARM: dts: imx: add initial imx6sx device tree source
Add initial device tree source for i.MX6 SoloX SoC.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Sun, 11 May 2014 13:59:26 +0000 (21:59 +0800)]
ARM: dts: imx: add pin function header for imx6sx
Add pin function header for i.MX6 SoloX SoC.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Fri, 18 Jul 2014 08:47:26 +0000 (16:47 +0800)]
Merge tag 'imx-soc-3.17' into imx/dt
The i.MX SoC changes for 3.17:
- Add devicetree support for i.MX1 and i.MX21 clock driver
- Use CLOCKSOURCE_OF_DECLARE() to initialize timer for DT targets
- Use of_clk_init() to initialize i.MX25 and i.MX27 clock driver in
device tree boot
- Remove i.MX1 camera support
- Remove i.MX27 IP Camera and Lite-Kit board support
- Add suspend and cpuidle support for i.mx6sx
- Clean up unused clk_register_clkdev() lookups
- Update imx-weim bus driver to support populating devices on a simple
bus
- Switch i.MX27 and i.MX6QDL clock driver to use macro for clock IDs
- Make i.MX51 a DT only platform and clean up the non-DT support code
- Support disabling supervisor protect via DT
- Random defconfig updates
Stefan Agner [Tue, 15 Jul 2014 12:56:19 +0000 (14:56 +0200)]
ARM: imx: clk-vf610: fix FlexCAN clock gating
Extend the clock control for FlexCAN with the second gate which
enable the clocks in the Clock Divider (CCM_CSCDR2) register too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sun, 13 Jul 2014 05:34:00 +0000 (09:34 +0400)]
ARM: i.MX: Use CLOCKSOURCE_OF_DECLARE() for DT targets
This patch uses clocksource_of_init() call for DT targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Steffen Trumtrar [Mon, 7 Jul 2014 09:41:27 +0000 (11:41 +0200)]
ARM: i.MX53: globally disable supervisor protect
Most peripherals on the i.MX53 have an
Off-Platform Peripheral Access Control Register (OPACR)
in which the access rights (together with the MPROT registers) can be declared.
However, this does not seem to work for example for SSI1+SDMA, because the
supervisor bit is not set for the SDMA unit.
It does work for SSI2, the QSB for example uses SSI2 for its audio. But SSI2 only
works because it does NOT have an OPACR.
The right solution would be to fix the access rights for the SDMA, but the unit
responsible for this is the Central Security Unit (CSU), which of course is NOT
documented. So, until documentation for this is openly available, turn off the
supervisor protection because it cripples the hardware.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Steffen Trumtrar [Mon, 7 Jul 2014 09:41:26 +0000 (11:41 +0200)]
ARM: i.MX: allow disabling supervisor protect via DT
The i.MX SoCs allow to setup fine grained access rights to peripherals on the
AIPS bus.
This is done via the Peripheral Access Register (PAR) in e.g. the i.MX21
or in later SoC versions the Off-Platform Peripheral Access Control Register
(OPACR), e.g. i.MX53.
Under certain circumstances this leads to problems in which bus masters are
not granted their access rights to peripherals.
To be able to disable these restrictions on DT platforms, add a helper function
that looks for AIPS nodes in the DT and disables them for every compatible node
it finds.
The compatible has to be declared in the mach-specific entry file, where this
helper function should then be called.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:36:09 +0000 (09:36 +0400)]
ARM: i.MX27 clk: Add 26 MHz oscillator circuit clock gate
This patch adds missing 26 MHz oscillator circuit clock gate support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:36:08 +0000 (09:36 +0400)]
ARM: i.MX27 clk: Remove unused definitions
This patch removes definitions which not used anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:36:06 +0000 (09:36 +0400)]
ARM: i.MX27 clk: Introduce DT include for clock provider
Use clock defines in order to make devicetrees more human readable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:00:01 +0000 (09:00 +0400)]
ARM: i.MX: Remove Freescale Logic Product Development i.MX27 Lite-Kit board support
The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board.
However, the support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 04:51:57 +0000 (08:51 +0400)]
ARM: i.MX: Remove excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27
This patch removes excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27.
Instead we use SOC_IMX*.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 04:51:38 +0000 (08:51 +0400)]
ARM: i.MX: Remove i.MX1 camera support
i.MX1 camera driver has been removed by the commit
90b055898e.
This patch removes remaining support files for this camera.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabian Frederick [Fri, 4 Jul 2014 19:03:10 +0000 (21:03 +0200)]
ARM: imx: use PTR_ERR_OR_ZERO
replace IS_ERR/PTR_ERR
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Liu Ying [Fri, 4 Jul 2014 09:00:41 +0000 (17:00 +0800)]
bus: imx-weim: populate devices on a simple bus
There could be some memory map devices located in
a certain chip select region of the i.MX WEIM.
The devices could be attached to a simple bus(for
example, a AXI bus) whose root node is one child
device tree node of the i.MX WEIM device tree node.
There should be a bridge(very likely, software
transparent) bewteen the i.MX WEIM and the simple bus.
This patch makes the i.MX WEIM driver possible to
populate devices on a simple bus. In this way, people
may try various IPs(in a FPGA, maybe) outside of i.MX
chips with the i.MX WEIM embedded.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Arnd Bergmann [Thu, 3 Jul 2014 14:22:54 +0000 (16:22 +0200)]
ARM: imx: build cpu_is_imx6sl function conditionally
imx6q_pm_enter calls imx6sl_set_wait_clk when run on an imx6sl
based machine. However if support for imx6sl is not enabled
at compile time, this prevents us from building the kernel and
we get this link error instead:
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
:(.text+0x4b84): undefined reference to `imx6sl_set_wait_clk'
This makes the cpu_is_imx6sl function conditionally return false
if imx6sl is disabled at compile-time, which matches what the
older cpu_is_mx* macros did. We have similar inline functions for
the other imx6 variants, but so far I have not run into a case
where the extra #ifdef is necessary.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Arnd Bergmann [Thu, 3 Jul 2014 14:16:06 +0000 (16:16 +0200)]
ARM: imx: imx6sx uses imx6q cpuidle code
Building a kernel for imx6sx but without imx6q support results in
this link error because of the missing cpuidle driver:
arch/arm/mach-imx/built-in.o: In function `imx6sx_init_late'::(.init.text+0xc228):
undefined reference to `imx6q_cpuidle_init'
This patch adds a Makefile entry so we always build support for
the imx6q_cpuidle code when at least one of the 6sx or 6q variants
are enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Wed, 2 Jul 2014 07:24:30 +0000 (15:24 +0800)]
ARM: imx: drop PL310 errata 588369 and 727915
The PL310 integrated on i.MX6 series and VF610 are revision r3p1 and
later. Per ARM PL310 errata document, 588369 is fixed in r2p0 and
727915 is fixed in r3p1. Neither is needed for i.MX6 or VF610. So
let's drop them.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Wed, 2 Jul 2014 19:13:19 +0000 (21:13 +0200)]
ARM: imx_v6_v7_defconfig: add FSL_EDMA and PRINTK_TIME
Add EDMA for DMA support for Vybrid SoCs. Also add printk time.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 2 Jul 2014 14:58:51 +0000 (11:58 -0300)]
ARM: imx: clk-imx6sx: register SSI/SSI_IPG as shared gate clocks
SSI and SSI_IPG are clocks controlled by the same clock gating field, so
register them with imx_clk_gate2_shared.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Tue, 1 Jul 2014 11:09:02 +0000 (13:09 +0200)]
ARM: imx_v6_v7_defconfig: Enable flexcan driver for can support
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Tue, 1 Jul 2014 11:08:58 +0000 (13:08 +0200)]
ARM: imx_v6_v7_defconfig: Enable STMPE gpio support
Enable STMPE gpio support as this is used on MX6 Data Modul edm-qmx6
board.
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 1 Jul 2014 08:03:00 +0000 (16:03 +0800)]
ARM: imx: mark .dt_compat as const
Otherwise GCC will mark the .init.rodata section R/W, which causes
a compile error once we add other real R/O data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Tue, 1 Jul 2014 03:12:52 +0000 (00:12 -0300)]
ARM: mx6: Only check for 1.2GHz for mx6quad
It is only the mx6quad variant that can run up to 1.2GHz, so add the check
accordingly.
This avoids getting the following warning on a mx6solo:
failed to disable 1.2 GHz OPP
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 25 Jun 2014 20:28:53 +0000 (17:28 -0300)]
ARM: imx_v4_v5_defconfig: Add USB device options
Allow USB device to work by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Denis Carikli [Wed, 25 Jun 2014 12:41:36 +0000 (14:41 +0200)]
ARM: i.MX25 clk: Use of_clk_init() for DT case
Replace .init_time() hook with of_clk_init() for DT targets.
Based on:
d4347ee ARM: i.MX27 clk: Use of_clk_init() for DT case
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Denis Carikli [Wed, 25 Jun 2014 12:41:34 +0000 (14:41 +0200)]
ARM i.MX25 clk: Fix gpt timer clock.
The gpt0 timer clock has been wrong since:
6bbaec5 ARM i.MX25: implement clocks using common clock framework
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This page took 0.048916 seconds and 5 git commands to generate.