Suresh Siddha [Thu, 20 Sep 2012 18:01:49 +0000 (11:01 -0700)]
x86, kvm: fix kvm's usage of kernel_fpu_begin/end()
Preemption is disabled between kernel_fpu_begin/end() and as such
it is not a good idea to use these routines in kvm_load/put_guest_fpu()
which can be very far apart.
kvm_load/put_guest_fpu() routines are already called with
preemption disabled and KVM already uses the preempt notifier to save
the guest fpu state using kvm_put_guest_fpu().
So introduce __kernel_fpu_begin/end() routines which don't touch
preemption and use them instead of kernel_fpu_begin/end()
for KVM's use model of saving/restoring guest FPU state.
Also with this change (and with eagerFPU model), fix the host cr0.TS vm-exit
state in the case of VMX. For eagerFPU case, host cr0.TS is always clear.
So no need to worry about it. For the traditional lazyFPU restore case,
change the cr0.TS bit for the host state during vm-exit to be always clear
and cr0.TS bit is set in the __vmx_load_host_state() when the FPU
(guest FPU or the host task's FPU) state is not active. This ensures
that the host/guest FPU state is properly saved, restored
during context-switch and with interrupts (using irq_fpu_usable()) not
stomping on the active FPU state.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1348164109.26695.338.camel@sbsiddha-desk.sc.intel.com
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Mon, 10 Sep 2012 17:40:08 +0000 (10:40 -0700)]
x86, fpu: remove cpu_has_xmm check in the fx_finit()
CPUs with FXSAVE but no XMM/MXCSR (Pentium II from Intel,
Crusoe/TM-3xxx/5xxx from Transmeta, and presumably some of the K6
generation from AMD) ever looked at the mxcsr field during
fxrstor/fxsave. So remove the cpu_has_xmm check in the fx_finit()
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1347300665-6209-6-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Mon, 10 Sep 2012 17:32:32 +0000 (10:32 -0700)]
x86, fpu: make eagerfpu= boot param tri-state
Add the "eagerfpu=auto" (that selects the default scheme in
enabling eagerfpu) which can override compiled-in boot parameters
like "eagerfpu=on/off" (that force enable/disable eagerfpu).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1347300665-6209-5-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Thu, 6 Sep 2012 22:05:18 +0000 (15:05 -0700)]
x86, fpu: enable eagerfpu by default for xsaveopt
xsaveopt/xrstor support optimized state save/restore by tracking the
INIT state and MODIFIED state during context-switch.
Enable eagerfpu by default for processors supporting xsaveopt.
Can be disabled by passing "eagerfpu=off" boot parameter.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1347300665-6209-3-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Thu, 6 Sep 2012 21:58:52 +0000 (14:58 -0700)]
x86, fpu: decouple non-lazy/eager fpu restore from xsave
Decouple non-lazy/eager fpu restore policy from the existence of the xsave
feature. Introduce a synthetic CPUID flag to represent the eagerfpu
policy. "eagerfpu=on" boot paramter will enable the policy.
Requested-by: H. Peter Anvin <hpa@zytor.com>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1347300665-6209-2-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Fri, 24 Aug 2012 21:13:02 +0000 (14:13 -0700)]
x86, fpu: use non-lazy fpu restore for processors supporting xsave
Fundamental model of the current Linux kernel is to lazily init and
restore FPU instead of restoring the task state during context switch.
This changes that fundamental lazy model to the non-lazy model for
the processors supporting xsave feature.
Reasons driving this model change are:
i. Newer processors support optimized state save/restore using xsaveopt and
xrstor by tracking the INIT state and MODIFIED state during context-switch.
This is faster than modifying the cr0.TS bit which has serializing semantics.
ii. Newer glibc versions use SSE for some of the optimized copy/clear routines.
With certain workloads (like boot, kernel-compilation etc), application
completes its work with in the first 5 task switches, thus taking upto 5 #DNA
traps with the kernel not getting a chance to apply the above mentioned
pre-load heuristic.
iii. Some xstate features (like AMD's LWP feature) don't honor the cr0.TS bit
and thus will not work correctly in the presence of lazy restore. Non-lazy
state restore is needed for enabling such features.
Some data on a two socket SNB system:
* Saved 20K DNA exceptions during boot on a two socket SNB system.
* Saved 50K DNA exceptions during kernel-compilation workload.
* Improved throughput of the AVX based checksumming function inside the
kernel by ~15% as xsave/xrstor is faster than the serializing clts/stts
pair.
Also now kernel_fpu_begin/end() relies on the patched
alternative instructions. So move check_fpu() which uses the
kernel_fpu_begin/end() after alternative_instructions().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1345842782-24175-7-git-send-email-suresh.b.siddha@intel.com
Merge 32-bit boot fix from,
Link: http://lkml.kernel.org/r/1347300665-6209-4-git-send-email-suresh.b.siddha@intel.com
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Fri, 24 Aug 2012 21:13:01 +0000 (14:13 -0700)]
lguest, x86: handle guest TS bit for lazy/non-lazy fpu host models
Instead of using unlazy_fpu() check if user_has_fpu() and set/clear
the host TS bits so that the lguest works fine with both the
lazy/non-lazy FPU host models with minimal changes.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1345842782-24175-6-git-send-email-suresh.b.siddha@intel.com
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Fri, 24 Aug 2012 21:13:00 +0000 (14:13 -0700)]
x86, fpu: always use kernel_fpu_begin/end() for in-kernel FPU usage
use kernel_fpu_begin/end() instead of unconditionally accessing cr0 and
saving/restoring just the few used xmm/ymm registers.
This has some advantages like:
* If the task's FPU state is already active, then kernel_fpu_begin()
will just save the user-state and avoiding the read/write of cr0.
In general, cr0 accesses are much slower.
* Manual save/restore of xmm/ymm registers will affect the 'modified' and
the 'init' optimizations brought in the by xsaveopt/xrstor
infrastructure.
* Foward compatibility with future vector register extensions will be a
problem if the xmm/ymm registers are manually saved and restored
(corrupting the extended state of those vector registers).
With this patch, there was no significant difference in the xor throughput
using AVX, measured during boot.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1345842782-24175-5-git-send-email-suresh.b.siddha@intel.com
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: NeilBrown <neilb@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Fri, 24 Aug 2012 21:12:59 +0000 (14:12 -0700)]
x86, kvm: use kernel_fpu_begin/end() in kvm_load/put_guest_fpu()
kvm's guest fpu save/restore should be wrapped around
kernel_fpu_begin/end(). This will avoid for example taking a DNA
in kvm_load_guest_fpu() when it tries to load the fpu immediately
after doing unlazy_fpu() on the host side.
More importantly this will prevent the host process fpu from being
corrupted.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1345842782-24175-4-git-send-email-suresh.b.siddha@intel.com
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Fri, 24 Aug 2012 21:12:58 +0000 (14:12 -0700)]
x86, fpu: remove unnecessary user_fpu_end() in save_xstate_sig()
Few lines below we do drop_fpu() which is more safer. Remove the
unnecessary user_fpu_end() in save_xstate_sig(), which allows
the drop_fpu() to ignore any pending exceptions from the user-space
and drop the current fpu.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1345842782-24175-3-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Fri, 24 Aug 2012 21:12:57 +0000 (14:12 -0700)]
x86, fpu: drop_fpu() before restoring new state from sigframe
No need to save the state with unlazy_fpu(), that is about to get overwritten
by the state from the signal frame. Instead use drop_fpu() and continue
to restore the new state.
Also fold the stop_fpu_preload() into drop_fpu().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1345842782-24175-2-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Tue, 24 Jul 2012 23:05:29 +0000 (16:05 -0700)]
x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels
Currently for x86 and x86_32 binaries, fpstate in the user sigframe is copied
to/from the fpstate in the task struct.
And in the case of signal delivery for x86_64 binaries, if the fpstate is live
in the CPU registers, then the live state is copied directly to the user
sigframe. Otherwise fpstate in the task struct is copied to the user sigframe.
During restore, fpstate in the user sigframe is restored directly to the live
CPU registers.
Historically, different code paths led to different bugs. For example,
x86_64 code path was not preemption safe till recently. Also there is lot
of code duplication for support of new features like xsave etc.
Unify signal handling code paths for x86 and x86_64 kernels.
New strategy is as follows:
Signal delivery: Both for 32/64-bit frames, align the core math frame area to
64bytes as needed by xsave (this where the main fpu/extended state gets copied
to and excludes the legacy compatibility fsave header for the 32-bit [f]xsave
frames). If the state is live, copy the register state directly to the user
frame. If not live, copy the state in the thread struct to the user frame. And
for 32-bit [f]xsave frames, construct the fsave header separately before
the actual [f]xsave area.
Signal return: As the 32-bit frames with [f]xstate has an additional
'fsave' header, copy everything back from the user sigframe to the
fpstate in the task structure and reconstruct the fxstate from the 'fsave'
header (Also user passed pointers may not be correctly aligned for
any attempt to directly restore any partial state). At the next fpstate usage,
everything will be restored to the live CPU registers.
For all the 64-bit frames and the 32-bit fsave frame, restore the state from
the user sigframe directly to the live CPU registers. 64-bit signals always
restored the math frame directly, so we can expect the math frame pointer
to be correctly aligned. For 32-bit fsave frames, there are no alignment
requirements, so we can restore the state directly.
"lat_sig catch" microbenchmark numbers (for x86, x86_64, x86_32 binaries) are
with in the noise range with this change.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1343171129-2747-4-git-send-email-suresh.b.siddha@intel.com
[ Merged in compilation fix ]
Link: http://lkml.kernel.org/r/1344544736.8326.17.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Tue, 24 Jul 2012 23:05:28 +0000 (16:05 -0700)]
x86, fpu: Consolidate inline asm routines for saving/restoring fpu state
Consolidate x86, x86_64 inline asm routines saving/restoring fpu state
using config_enabled().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1343171129-2747-3-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Suresh Siddha [Tue, 24 Jul 2012 23:05:27 +0000 (16:05 -0700)]
x86, signal: Cleanup ifdefs and is_ia32, is_x32
Use config_enabled() to cleanup the definitions of is_ia32/is_x32. Move
the function prototypes to the header file to cleanup ifdefs,
and move the x32_setup_rt_frame() code around.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1343171129-2747-2-git-send-email-suresh.b.siddha@intel.com
Merged in compilation fix from,
Link: http://lkml.kernel.org/r/1344544736.8326.17.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Mathias Krause [Sun, 2 Sep 2012 21:31:46 +0000 (23:31 +0200)]
x86/iommu: Use NULL instead of plain 0 for __IOMMU_INIT
IOMMU_INIT_POST and IOMMU_INIT_POST_FINISH pass the plain value
0 instead of NULL to __IOMMU_INIT. Fix this and make sparse
happy by doing so.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1346621506-30857-8-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mathias Krause [Sun, 2 Sep 2012 21:31:45 +0000 (23:31 +0200)]
x86/iommu: Drop duplicate const in __IOMMU_INIT
It's redundant and makes sparse complain about it.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/1346621506-30857-7-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mathias Krause [Sun, 2 Sep 2012 21:31:44 +0000 (23:31 +0200)]
x86/fpu/xsave: Keep __user annotation in casts
Don't remove the __user annotation of the fpstate pointer, but
drop the superfluous void * cast instead.
This fixes the following sparse warnings:
xsave.c:135:15: warning: cast removes address space of expression
xsave.c:135:15: warning: incorrect type in argument 1 (different address spaces)
xsave.c:135:15: expected void const volatile [noderef] <asn:1>*<noident>
[...]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1346621506-30857-6-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mathias Krause [Sun, 2 Sep 2012 21:31:43 +0000 (23:31 +0200)]
x86/pci/probe_roms: Add missing __iomem annotation to pci_map_biosrom()
Stay in sync with the declaration and fix the corresponding
sparse warnings.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Link: http://lkml.kernel.org/r/1346621506-30857-5-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mathias Krause [Sun, 2 Sep 2012 21:31:42 +0000 (23:31 +0200)]
x86/signals: ia32_signal.c: add __user casts to fix sparse warnings
Fix the following sparse warnings by adding appropriate __user
casts and annotations:
ia32_signal.c:165:38: warning: incorrect type in argument 1 (different address spaces)
ia32_signal.c:165:38: expected struct sigaltstack const [noderef] [usertype] <asn:1>*<noident>
ia32_signal.c:165:38: got struct sigaltstack *
[...]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/1346621506-30857-4-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mathias Krause [Sun, 2 Sep 2012 21:31:41 +0000 (23:31 +0200)]
x86/vdso: Add __user annotation to VDSO32_SYMBOL
The address calculated by VDSO32_SYMBOL() is a pointer into
userland. Add the __user annotation to fix related sparse
warnings in its users.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Andy Lutomirski <luto@MIT.EDU>
Link: http://lkml.kernel.org/r/1346621506-30857-3-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mathias Krause [Sun, 2 Sep 2012 21:31:40 +0000 (23:31 +0200)]
x86: Fix __user annotations in asm/sys_ia32.h
Fix the following sparse warnings:
sys_ia32.c:293:38: warning: incorrect type in argument 2 (different address spaces)
sys_ia32.c:293:38: expected unsigned int [noderef] [usertype] <asn:1>*stat_addr
sys_ia32.c:293:38: got unsigned int *stat_addr
Ironically, sys_ia32.h was introduced to fix sparse warnings but
missed that one.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Link: http://lkml.kernel.org/r/1346621506-30857-2-git-send-email-minipli@googlemail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Sun, 2 Sep 2012 18:30:10 +0000 (11:30 -0700)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French.
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix cifs_do_create error hadnling
cifs: print error code if smb signature verification fails
CIFS: Fix log messages in packet checking for SMB2
CIFS: Protect i_nlink from being negative
Linus Torvalds [Sun, 2 Sep 2012 18:28:00 +0000 (11:28 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) NLA_PUT* --> nla_put_* conversion got one case wrong in
nfnetlink_log, fix from Patrick McHardy.
2) Missed error return check in ipw2100 driver, from Julia Lawall.
3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix
from Eric Dumazet.
4) SFC driver erroneously reversed src and dst when reporting filters
via ethtool.
5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in
sja1000 can platform driver, from Alexey Khoroshilov and Sven
Schmitt.
6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only
take the lock when we really need to. From Eric Dumazet.
7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso.
8) CWND reduction in TCP is done incorrectly during non-SACK recovery,
fix from Yuchung Cheng.
9) Revert netpoll change, and fix what was actually a driver specific
problem. From Amerigo Wang. This should cure bootup hangs with
netconsole some people reported.
10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page
pointer. From Ian Campbell.
11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso.
12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet.
13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this
situation. From Oliver Neukum.
14) The davinci ethernet driver triggers an OOPS on removal because it
frees an MDIO object before unregistering it. Fix from Bin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
net: qmi_wwan: add several new Gobi devices
fddi: 64 bit bug in smt_add_para()
net: ethernet: fix kernel OOPS when remove davinci_mdio module
net/xfrm/xfrm_state.c: fix error return code
net: ipv6: fix error return code
net: qmi_wwan: new device: Foxconn/Novatel E396
usbnet: fix deadlock in resume
cs89x0 : packet reception not working
netfilter: nf_conntrack: fix racy timer handling with reliable events
bnx2x: Correct the ndo_poll_controller call
bnx2x: Move netif_napi_add to the open call
ipv4: must use rcu protection while calling fib_lookup
bnx2x: fix 57840_MF pci id
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
e1000e: DoS while TSO enabled caused by link partner with small MSS
l2tp: avoid to use synchronize_rcu in tunnel free function
gianfar: fix default tx vlan offload feature flag
netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
netfilter: nfnetlink_log: fix error return code in init path
...
Bjørn Mork [Sat, 1 Sep 2012 03:47:26 +0000 (03:47 +0000)]
net: qmi_wwan: add several new Gobi devices
Gobi devices are composite, needing both the qcserial and
qmi_wwan drivers to support all functions. Re-syncing the
list of supported devices with qcserial.
Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@tempietto.lan>
Dan Carpenter [Sat, 1 Sep 2012 09:57:40 +0000 (09:57 +0000)]
fddi: 64 bit bug in smt_add_para()
The intent was to set 4 bytes of data so that's why the sp_len is set
to 4 on the next line. The cast to u_long pointer clears 8 bytes
on 64 bit arches.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@tempietto.lan>
Linus Torvalds [Sat, 1 Sep 2012 17:39:58 +0000 (10:39 -0700)]
Linux 3.6-rc4
John Stultz [Fri, 31 Aug 2012 17:30:06 +0000 (13:30 -0400)]
time: Move ktime_t overflow checking into timespec_valid_strict
Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit
4e8b14526ca7 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.
Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.
This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 1 Sep 2012 00:02:58 +0000 (17:02 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix KVM_GET_MSR for PV EOI
kvm: Fix nonsense handling of compat ioctl
Linus Torvalds [Sat, 1 Sep 2012 00:02:20 +0000 (17:02 -0700)]
Merge tag 'parisc-fixes' of git://git./linux/kernel/git/jejb/parisc-2.6
Pull PARISC fixes from James Bottomley:
"This is a set of two bug fixes. One is the ATOMIC problem which is
now causing a compile failure in certain situations. The other is
mishandling of PER_LINUX32 which may also cause user visible effects.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix personality flag check in copy_thread()
[PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts
Linus Torvalds [Sat, 1 Sep 2012 00:01:31 +0000 (17:01 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of s390 bug fixes for 3.5-rc4"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/32: Don't clobber personality flags on exec
s390/smp: add missing smp_store_status() for !SMP
s390/dasd: fix ioctl return value
s390: Always use "long" for ssize_t to match size_t
Bin Liu [Thu, 30 Aug 2012 06:37:32 +0000 (06:37 +0000)]
net: ethernet: fix kernel OOPS when remove davinci_mdio module
davinci mdio device is not unregistered from mdiobus when removing
the module, which causes BUG_ON() when free the device from mdiobus.
Calling mdiobus_unregister() before mdiobus_free() fixes the issue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 29 Aug 2012 06:49:15 +0000 (06:49 +0000)]
net/xfrm/xfrm_state.c: fix error return code
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 29 Aug 2012 06:49:12 +0000 (06:49 +0000)]
net: ipv6: fix error return code
Initialize return variable before exiting on an error path.
The initial initialization of the return variable is also dropped, because
that value is never used.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksander Morgado [Tue, 28 Aug 2012 02:30:32 +0000 (02:30 +0000)]
net: qmi_wwan: new device: Foxconn/Novatel E396
Foxconn-branded Novatel E396, Gobi3k modem.
Cc: Dan Williams <dcbw@redhat.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Ben Chan <benchan@google.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Sun, 26 Aug 2012 20:41:38 +0000 (20:41 +0000)]
usbnet: fix deadlock in resume
A usbnet device can share a multifunction device
with a storage device. If the storage device is autoresumed
the usbnet devices also needs to be autoresumed. Allocating
memory with GFP_KERNEL can deadlock in this case.
This should go back into all kernels that have
commit
65841fd5132c3941cdf5df09e70df3ed28323212
That is 3.5
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Jaccon Bastiaansen [Mon, 27 Aug 2012 11:53:51 +0000 (11:53 +0000)]
cs89x0 : packet reception not working
The RxCFG register of the CS89x0 could be configured incorrectly
(because of misplaced parentheses), resulting in the disabling
of packet reception.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Aug 2012 17:06:37 +0000 (13:06 -0400)]
Merge branch 'master' of git://1984.lsi.us.es/nf
Pablo Neira Ayuso [Wed, 29 Aug 2012 16:25:49 +0000 (16:25 +0000)]
netfilter: nf_conntrack: fix racy timer handling with reliable events
Existing code assumes that del_timer returns true for alive conntrack
entries. However, this is not true if reliable events are enabled.
In that case, del_timer may return true for entries that were
just inserted in the dying list. Note that packets / ctnetlink may
hold references to conntrack entries that were just inserted to such
list.
This patch fixes the issue by adding an independent timer for
event delivery. This increases the size of the ecache extension.
Still we can revisit this later and use variable size extensions
to allocate this area on demand.
Tested-by: Oliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Merav Sicron [Mon, 27 Aug 2012 03:26:20 +0000 (03:26 +0000)]
bnx2x: Correct the ndo_poll_controller call
This patch correct poll_bnx2x (ndo_poll_controller call) which was not
functioning well with MSI-X.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merav Sicron [Mon, 27 Aug 2012 03:26:19 +0000 (03:26 +0000)]
bnx2x: Move netif_napi_add to the open call
Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 28 Aug 2012 12:33:07 +0000 (12:33 +0000)]
ipv4: must use rcu protection while calling fib_lookup
Following lockdep splat was reported by Pavel Roskin :
[ 1570.586223] ===============================
[ 1570.586225] [ INFO: suspicious RCU usage. ]
[ 1570.586228] 3.6.0-rc3-wl-main #98 Not tainted
[ 1570.586229] -------------------------------
[ 1570.586231] /home/proski/src/linux/net/ipv4/route.c:645 suspicious rcu_dereference_check() usage!
[ 1570.586233]
[ 1570.586233] other info that might help us debug this:
[ 1570.586233]
[ 1570.586236]
[ 1570.586236] rcu_scheduler_active = 1, debug_locks = 0
[ 1570.586238] 2 locks held by Chrome_IOThread/4467:
[ 1570.586240] #0: (slock-AF_INET){+.-...}, at: [<
ffffffff814f2c0c>] release_sock+0x2c/0xa0
[ 1570.586253] #1: (fnhe_lock){+.-...}, at: [<
ffffffff815302fc>] update_or_create_fnhe+0x2c/0x270
[ 1570.586260]
[ 1570.586260] stack backtrace:
[ 1570.586263] Pid: 4467, comm: Chrome_IOThread Not tainted 3.6.0-rc3-wl-main #98
[ 1570.586265] Call Trace:
[ 1570.586271] [<
ffffffff810976ed>] lockdep_rcu_suspicious+0xfd/0x130
[ 1570.586275] [<
ffffffff8153042c>] update_or_create_fnhe+0x15c/0x270
[ 1570.586278] [<
ffffffff815305b3>] __ip_rt_update_pmtu+0x73/0xb0
[ 1570.586282] [<
ffffffff81530619>] ip_rt_update_pmtu+0x29/0x90
[ 1570.586285] [<
ffffffff815411dc>] inet_csk_update_pmtu+0x2c/0x80
[ 1570.586290] [<
ffffffff81558d1e>] tcp_v4_mtu_reduced+0x2e/0xc0
[ 1570.586293] [<
ffffffff81553bc4>] tcp_release_cb+0xa4/0xb0
[ 1570.586296] [<
ffffffff814f2c35>] release_sock+0x55/0xa0
[ 1570.586300] [<
ffffffff815442ef>] tcp_sendmsg+0x4af/0xf50
[ 1570.586305] [<
ffffffff8156fc60>] inet_sendmsg+0x120/0x230
[ 1570.586308] [<
ffffffff8156fb40>] ? inet_sk_rebuild_header+0x40/0x40
[ 1570.586312] [<
ffffffff814f4bdd>] ? sock_update_classid+0xbd/0x3b0
[ 1570.586315] [<
ffffffff814f4c50>] ? sock_update_classid+0x130/0x3b0
[ 1570.586320] [<
ffffffff814ec435>] do_sock_write+0xc5/0xe0
[ 1570.586323] [<
ffffffff814ec4a3>] sock_aio_write+0x53/0x80
[ 1570.586328] [<
ffffffff8114bc83>] do_sync_write+0xa3/0xe0
[ 1570.586332] [<
ffffffff8114c5a5>] vfs_write+0x165/0x180
[ 1570.586335] [<
ffffffff8114c805>] sys_write+0x45/0x90
[ 1570.586340] [<
ffffffff815d2722>] system_call_fastpath+0x16/0x1b
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 26 Aug 2012 00:35:45 +0000 (00:35 +0000)]
bnx2x: fix 57840_MF pci id
Commit
c3def943c7117d42caaed3478731ea7c3c87190e have added support for
new pci ids of the 57840 board, while failing to change the obsolete value
in 'pci_ids.h'.
This patch does so, allowing the probe of such devices.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Francesco Ruggeri [Fri, 24 Aug 2012 07:38:35 +0000 (07:38 +0000)]
net: ipv4: ipmr_expire_timer causes crash when removing net namespace
When tearing down a net namespace, ipv4 mr_table structures are freed
without first deactivating their timers. This can result in a crash in
run_timer_softirq.
This patch mimics the corresponding behaviour in ipv6.
Locking and synchronization seem to be adequate.
We are about to kfree mrt, so existing code should already make sure that
no other references to mrt are pending or can be created by incoming traffic.
The functions invoked here do not cause new references to mrt or other
race conditions to be created.
Invoking del_timer_sync guarantees that ipmr_expire_timer is inactive.
Both ipmr_expire_process (whose completion we may have to wait in
del_timer_sync) and mroute_clean_tables internally use mfc_unres_lock
or other synchronizations when needed, and they both only modify mrt.
Tested in Linux 3.4.8.
Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 24 Aug 2012 20:38:11 +0000 (20:38 +0000)]
e1000e: DoS while TSO enabled caused by link partner with small MSS
With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g. 64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring. This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e. When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state. After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.
Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.
Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.
This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xeb@mail.ru [Fri, 24 Aug 2012 01:07:38 +0000 (01:07 +0000)]
l2tp: avoid to use synchronize_rcu in tunnel free function
Avoid to use synchronize_rcu in l2tp_tunnel_free because context may be
atomic.
Signed-off-by: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Thu, 23 Aug 2012 21:46:25 +0000 (21:46 +0000)]
gianfar: fix default tx vlan offload feature flag
Commit -
"
b852b72 gianfar: fix bug caused by
87c288c6e9aa31720b72e2bc2d665e24e1653c3e"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso [Wed, 29 Aug 2012 15:24:09 +0000 (15:24 +0000)]
netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
We're hitting bug while trying to reinsert an already existing
expectation:
kernel BUG at kernel/timer.c:895!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
<IRQ>
[<
ffffffffa0069563>] nf_ct_expect_related_report+0x4a0/0x57a [nf_conntrack]
[<
ffffffff812d423a>] ? in4_pton+0x72/0x131
[<
ffffffffa00ca69e>] ip_nat_sdp_media+0xeb/0x185 [nf_nat_sip]
[<
ffffffffa00b5b9b>] set_expected_rtp_rtcp+0x32d/0x39b [nf_conntrack_sip]
[<
ffffffffa00b5f15>] process_sdp+0x30c/0x3ec [nf_conntrack_sip]
[<
ffffffff8103f1eb>] ? irq_exit+0x9a/0x9c
[<
ffffffffa00ca738>] ? ip_nat_sdp_media+0x185/0x185 [nf_nat_sip]
We have to remove the RTP expectation if the RTCP expectation hits EBUSY
since we keep trying with other ports until we succeed.
Reported-by: Rafal Fitt <rafalf@aplusc.com.pl>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ian Campbell [Wed, 22 Aug 2012 00:26:47 +0000 (00:26 +0000)]
xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.
This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 30 Aug 2012 16:11:33 +0000 (09:11 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
nothing too shocking or different."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
gma500: Consider CRTC initially active.
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm: Check for invalid cursor flags
drm: Initialize object type when using DRM_MODE() macro
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Heiko Carstens [Tue, 28 Aug 2012 08:02:08 +0000 (10:02 +0200)]
s390/32: Don't clobber personality flags on exec
In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of
59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Paul Menzel [Wed, 8 Aug 2012 21:12:19 +0000 (23:12 +0200)]
drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.
In commit
bc42aabc [2]
commit
bc42aabc6a01b92b0f961d65671564e0e1cd7592
Author: Adam Jackson <ajax@redhat.com>
Date: Wed May 23 16:26:54 2012 -0400
drm/edid/quirks: ViewSonic VA2026w
Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.
All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.
Please note that this monitor only has a VGA (D-Sub) connector [1].
[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=
bc42aabc6a01b92b0f961d65671564e0e1cd7592
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Julia Lawall [Wed, 29 Aug 2012 06:49:17 +0000 (06:49 +0000)]
netfilter: nfnetlink_log: fix error return code in init path
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Julia Lawall [Wed, 29 Aug 2012 06:49:16 +0000 (06:49 +0000)]
netfilter: ctnetlink: fix error return code in init path
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Julia Lawall [Wed, 29 Aug 2012 06:49:11 +0000 (06:49 +0000)]
ipvs: fix error return code
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dave Airlie [Thu, 30 Aug 2012 00:35:34 +0000 (10:35 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
Forest Bond [Mon, 13 Aug 2012 16:31:24 +0000 (16:31 +0000)]
gma500: Consider CRTC initially active.
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Wed, 29 Aug 2012 23:48:26 +0000 (19:48 -0400)]
drm/radeon: fix dig encoder selection on DCE61
Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Amerigo Wang [Fri, 24 Aug 2012 21:41:11 +0000 (21:41 +0000)]
netpoll: revert
6bdb7fe3104 and fix be_poll() instead
Against -net.
In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:
[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073] [<
ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075] [<
ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077] [<
ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080] [<
ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085] [<
ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088] [<
ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090] [<
ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095] [<
ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097] [<
ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100] [<
ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102] [<
ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240
by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:
http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpg
http://marc.info/?l=linux-netdev&m=
134563282530588&w=2
So it is safe to fix be2net driver code directly.
This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 29 Aug 2012 18:36:22 +0000 (11:36 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I've split out the big send/receive update from my last pull request
and now have just the fixes in my for-linus branch. The send/recv
branch will wander over to linux-next shortly though.
The largest patches in this pull are Josef's patches to fix DIO
locking problems and his patch to fix a crash during balance. They
are both well tested.
The rest are smaller fixes that we've had queued. The last rc came
out while I was hacking new and exciting ways to recover from a
misplaced rm -rf on my dev box, so these missed rc3."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
Btrfs: fix that repair code is spuriously executed for transid failures
Btrfs: fix ordered extent leak when failing to start a transaction
Btrfs: fix a dio write regression
Btrfs: fix deadlock with freeze and sync V2
Btrfs: revert checksum error statistic which can cause a BUG()
Btrfs: remove superblock writing after fatal error
Btrfs: allow delayed refs to be merged
Btrfs: fix enospc problems when deleting a subvol
Btrfs: fix wrong mtime and ctime when creating snapshots
Btrfs: fix race in run_clustered_refs
Btrfs: don't run __tree_mod_log_free_eb on leaves
Btrfs: increase the size of the free space cache
Btrfs: barrier before waitqueue_active
Btrfs: fix deadlock in wait_for_more_refs
btrfs: fix second lock in btrfs_delete_delayed_items()
Btrfs: don't allocate a seperate csums array for direct reads
Btrfs: do not strdup non existent strings
Btrfs: do not use missing devices when showing devname
Btrfs: fix that error value is changed by mistake
Btrfs: lock extents as we map them in DIO
...
Linus Torvalds [Wed, 29 Aug 2012 18:35:00 +0000 (11:35 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This will fix a warning for watchdog-test.c and it will remove a
duplicate include of delay.h"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: da9052: Remove duplicate inclusion of delay.h
watchdog: fix watchdog-test.c build warning
David Rientjes [Wed, 29 Aug 2012 02:57:21 +0000 (19:57 -0700)]
mm, slab: lock the correct nodelist after reenabling irqs
cache_grow() can reenable irqs so the cpu (and node) can change, so ensure
that we take list_lock on the correct nodelist.
This fixes an issue with commit
072bb0aa5e06 ("mm: sl[au]b: add
knowledge of PFMEMALLOC reserve pages") where list_lock for the wrong
node was taken after growing the cache.
Reported-and-tested-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian König [Wed, 29 Aug 2012 11:24:15 +0000 (13:24 +0200)]
drm/radeon: fix double free in radeon_gpu_reset
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Jerome Glisse [Tue, 28 Aug 2012 20:50:22 +0000 (16:50 -0400)]
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
https://bugzilla.redhat.com/show_bug.cgi?id=785375
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Mon, 27 Aug 2012 21:48:18 +0000 (17:48 -0400)]
drm/radeon: rework panel mode setup
Adjust the panel mode setup to match the behavior
of the vbios. Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 24 Aug 2012 22:21:21 +0000 (18:21 -0400)]
drm/radeon/atom: powergating fixes for DCE6
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Wed, 22 Aug 2012 13:54:56 +0000 (09:54 -0400)]
drm/radeon/atom: rework DIG modesetting on DCE3+
The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders. We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs. This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Tue, 21 Aug 2012 23:06:21 +0000 (19:06 -0400)]
drm/radeon: don't disable plls that are in use by other crtcs
Some plls are shared for DP.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Marek Olšák [Fri, 24 Aug 2012 12:27:36 +0000 (14:27 +0200)]
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Marek Olšák [Wed, 22 Aug 2012 15:02:43 +0000 (17:02 +0200)]
drm/radeon: initialize tracked CS state
This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Marek Olšák [Wed, 22 Aug 2012 15:02:42 +0000 (17:02 +0200)]
drm/radeon: fix reading CB_COLORn_MASK from the CS
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sachin Kamat [Tue, 7 Aug 2012 09:44:12 +0000 (15:14 +0530)]
watchdog: da9052: Remove duplicate inclusion of delay.h
delay.h header file was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Randy Dunlap [Mon, 23 Jul 2012 17:46:11 +0000 (10:46 -0700)]
watchdog: fix watchdog-test.c build warning
Fix compiler warning by making the function static:
Documentation/watchdog/src/watchdog-test.c:34:6: warning: no previous prototype for 'term'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Dave Airlie [Wed, 29 Aug 2012 10:09:23 +0000 (20:09 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
the availbale gtt space in the name of ... product differentiation
(Chris). This fixes an oops.
- Yet another no_lvds quirk entry."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Dave Airlie [Wed, 29 Aug 2012 10:05:40 +0000 (20:05 +1000)]
Merge branch 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
Ben says its just a single fix to avoid the wrong pcopy units being used.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
Ben Skeggs [Mon, 27 Aug 2012 06:22:49 +0000 (16:22 +1000)]
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist. And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.
This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.
Cc: stable@vger.kernel.org [3.5]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Stefan Behrens [Fri, 10 Aug 2012 14:58:21 +0000 (08:58 -0600)]
Btrfs: fix that repair code is spuriously executed for transid failures
If verify_parent_transid() fails for all mirrors, the current code
calls repair_io_failure() anyway which means:
- that the disk block is rewritten without repairing anything and
- that a kernel log message is printed which misleadingly claims
that a read error was corrected.
This is an example:
parent transid verify failed on
615015833600 wanted 110423 found 110424
parent transid verify failed on
615015833600 wanted 110423 found 110424
btrfs read error corrected: ino 1 off
615015833600 (dev /dev/...)
It is wrong to ignore the results from verify_parent_transid() and to
call repair_eb_io_failure() when the verification of the transids failed.
This commit fixes the issue.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Liu Bo [Wed, 22 Aug 2012 03:13:25 +0000 (21:13 -0600)]
Btrfs: fix ordered extent leak when failing to start a transaction
We cannot just return error before freeing ordered extent and releasing reserved
space when we fail to start a transacion.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Liu Bo [Thu, 23 Aug 2012 02:10:38 +0000 (20:10 -0600)]
Btrfs: fix a dio write regression
This bug is introduced by commit
3b8bde746f6f9bd36a9f05f5f3b6e334318176a9
(Btrfs: lock extents as we map them in DIO).
In dio write, we should unlock the section which we didn't do IO on in case that
we fall back to buffered write. But we need to not only unlock the section
but also cleanup reserved space for the section.
This bug was found while running xfstests 133, with this 133 no longer complains.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Fri, 24 Aug 2012 18:53:03 +0000 (12:53 -0600)]
Btrfs: fix deadlock with freeze and sync V2
We can deadlock with freeze right now because we unconditionally start a
transaction in our ->sync_fs() call. To fix this just check and see if we
have a running transaction to commit. This saves us from the deadlock
because at this point we'll have the umount sem for the sb so we're safe
from freezes coming in after we've done our check. With this patch the
freeze xfstests no longer deadlocks. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Stefan Behrens [Mon, 27 Aug 2012 14:30:03 +0000 (08:30 -0600)]
Btrfs: revert checksum error statistic which can cause a BUG()
Commit
442a4f6308e694e0fa6025708bd5e4e424bbf51c added btrfs device
statistic counters for detected IO and checksum errors to Linux 3.5.
The statistic part that counts checksum errors in
end_bio_extent_readpage() can cause a BUG() in a subfunction:
"kernel BUG at fs/btrfs/volumes.c:3762!"
That part is reverted with the current patch.
However, the counting of checksum errors in the scrub context remains
active, and the counting of detected IO errors (read, write or flush
errors) in all contexts remains active.
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Stefan Behrens [Wed, 1 Aug 2012 11:45:52 +0000 (05:45 -0600)]
Btrfs: remove superblock writing after fatal error
With commit
acce952b0, btrfs was changed to flag the filesystem with
BTRFS_SUPER_FLAG_ERROR and switch to read-only mode after a fatal
error happened like a write I/O errors of all mirrors.
In such situations, on unmount, the superblock is written in
btrfs_error_commit_super(). This is done with the intention to be able
to evaluate the error flag on the next mount. A warning is printed
in this case during the next mount and the log tree is ignored.
The issue is that it is possible that the superblock points to a root
that was not written (due to write I/O errors).
The result is that the filesystem cannot be mounted. btrfsck also does
not start and all the other btrfs-progs tools fail to start as well.
However, mount -o recovery is working well and does the right things
to recover the filesystem (i.e., don't use the log root, clear the
free space cache and use the next mountable root that is stored in the
root backup array).
This patch removes the writing of the superblock when
BTRFS_SUPER_FLAG_ERROR is set, and removes the handling of the error
flag in the mount function.
These lines can be used to reproduce the issue (using /dev/sdm):
SCRATCH_DEV=/dev/sdm
SCRATCH_MNT=/mnt
echo 0
25165824 linear $SCRATCH_DEV 0 | dmsetup create foo
ls -alLF /dev/mapper/foo
mkfs.btrfs /dev/mapper/foo
mount /dev/mapper/foo $SCRATCH_MNT
echo bar > $SCRATCH_MNT/foo
sync
echo 0
25165824 error | dmsetup reload foo
dmsetup resume foo
ls -alF $SCRATCH_MNT
touch $SCRATCH_MNT/1
ls -alF $SCRATCH_MNT
sleep 35
echo 0
25165824 linear $SCRATCH_DEV 0 | dmsetup reload foo
dmsetup resume foo
sleep 1
umount $SCRATCH_MNT
btrfsck /dev/mapper/foo
dmsetup remove foo
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Josef Bacik [Tue, 7 Aug 2012 20:00:32 +0000 (16:00 -0400)]
Btrfs: allow delayed refs to be merged
Daniel Blueman reported a bug with fio+balance on a ramdisk setup.
Basically what happens is the balance relocates a tree block which will drop
the implicit refs for all of its children and adds a full backref. Once the
block is relocated we have to add the implicit refs back, so when we cow the
block again we add the implicit refs for its children back. The problem
comes when the original drop ref doesn't get run before we add the implicit
refs back. The delayed ref stuff will specifically prefer ADD operations
over DROP to keep us from freeing up an extent that will have references to
it, so we try to add the implicit ref before it is actually removed and we
panic. This worked fine before because the add would have just canceled the
drop out and we would have been fine. But the backref walking work needs to
be able to freeze the delayed ref stuff in time so we have this ever
increasing sequence number that gets attached to all new delayed ref updates
which makes us not merge refs and we run into this issue.
So to fix this we need to merge delayed refs. So everytime we run a
clustered ref we need to try and merge all of its delayed refs. The backref
walking stuff locks the delayed ref head before processing, so if we have it
locked we are safe to merge any refs inside of the sequence number. If
there is no sequence number we can merge all refs. Doing this not only
fixes our bug but keeps the delayed ref code from adding and removing
useless refs and batching together multiple refs into one search instead of
one search per delayed ref, which will really help our commit times. I ran
this with Daniels test and 276 and I haven't seen any problems. Thanks,
Reported-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Wed, 8 Aug 2012 16:12:59 +0000 (10:12 -0600)]
Btrfs: fix enospc problems when deleting a subvol
Subvol delete is a special kind of awful where we use the global reserve to
cover the ENOSPC requirements. The problem is once we're done removing
everything we do a btrfs_update_inode(), which by default will try to do the
delayed update stuff which will use it's own reserve. There will be no
space in this reserve and we'll return ENOSPC. So instead use
btrfs_update_inode_fallback() which will just fallback to updating the inode
item in the case of enospc. This is fine because the global reserve covers
the space requirements for this. With this patch I can now delete a subvol
on a problem image Dave Sterba sent me. Thanks,
Reported-by: David Sterba <dave@jikos.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Miao Xie [Thu, 9 Aug 2012 03:39:36 +0000 (21:39 -0600)]
Btrfs: fix wrong mtime and ctime when creating snapshots
When we created a new snapshot, the mtime and ctime of its parent directory
were not updated. Fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Arne Jansen [Thu, 9 Aug 2012 06:16:53 +0000 (00:16 -0600)]
Btrfs: fix race in run_clustered_refs
With commit
commit
d1270cd91f308c9d22b2804720c36ccd32dbc35e
Author: Arne Jansen <sensille@gmx.net>
Date: Tue Sep 13 15:16:43 2011 +0200
Btrfs: put back delayed refs that are too new
I added a window where the delayed_ref's head->ref_mod code can diverge
from the sum of the remaining refs, because we release the head->mutex
in the middle. This leads to btrfs_lookup_extent_info returning wrong
numbers. This patch fixes this by adjusting the head's ref_mod with each
delayed ref we run.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Chris Mason [Tue, 7 Aug 2012 19:34:49 +0000 (15:34 -0400)]
Btrfs: don't run __tree_mod_log_free_eb on leaves
When we split a leaf, we may end up inserting a new root on top of that
leaf. The reflog code was incorrectly assuming the old root was always
a node. This makes sure we skip over leaves.
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Mon, 6 Aug 2012 19:46:38 +0000 (13:46 -0600)]
Btrfs: increase the size of the free space cache
Arne was complaining about the space cache having mismatching generation
numbers when debugging a deadlock. This is because we can run out of space
in our preallocated range for our space cache if you have a pretty
fragmented amount of space in your pinned space. So just increase the
amount of space we preallocate for space cache so we can be sure to have
enough space. This will only really affect data ranges since their the only
chunks that end up larger than 256MB. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Wed, 1 Aug 2012 19:36:24 +0000 (15:36 -0400)]
Btrfs: barrier before waitqueue_active
We need a barrir before calling waitqueue_active otherwise we will miss
wakeups. So in places that do atomic_dec(); then atomic_read() use
atomic_dec_return() which imply a memory barrier (see memory-barriers.txt)
and then add an explicit memory barrier everywhere else that need them.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Arne Jansen [Mon, 6 Aug 2012 20:18:51 +0000 (14:18 -0600)]
Btrfs: fix deadlock in wait_for_more_refs
Commit
a168650c introduced a waiting mechanism to prevent busy waiting in
btrfs_run_delayed_refs. This can deadlock with btrfs_run_ordered_operations,
where a tree_mod_seq is held while waiting for the io to complete, while
the end_io calls btrfs_run_delayed_refs.
This whole mechanism is unnecessary. If not enough runnable refs are
available to satisfy count, just return as count is more like a guideline
than a strict requirement.
In case we have to run all refs, commit transaction makes sure that no
other threads are working in the transaction anymore, so we just assert
here that no refs are blocked.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Fengguang Wu [Sat, 4 Aug 2012 07:45:02 +0000 (01:45 -0600)]
btrfs: fix second lock in btrfs_delete_delayed_items()
Fix a real bug caught by coccinelle.
fs/btrfs/delayed-inode.c:1013:1-11: second lock on line 1013
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Josef Bacik [Fri, 3 Aug 2012 20:49:19 +0000 (16:49 -0400)]
Btrfs: don't allocate a seperate csums array for direct reads
We've been allocating a big array for csums instead of storing them in the
io_tree like we do for buffered reads because previously we were locking the
entire range, so we didn't have an extent state for each sector of the
range. But now that we do the range locking as we map the buffers we can
limit the mapping lenght to sectorsize and use the private part of the
io_tree for our csums. This allows us to avoid an extra memory allocation
for direct reads which could incur latency. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Thu, 2 Aug 2012 14:23:59 +0000 (10:23 -0400)]
Btrfs: do not strdup non existent strings
When we close devices we add back empty devices for some reason that escapes
me. In the case of a missing dev we don't allocate an rcu_string for it's
name, so check to see if the device has a name and if it doesn't don't
bother strdup()'ing it. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Thu, 2 Aug 2012 14:22:20 +0000 (10:22 -0400)]
Btrfs: do not use missing devices when showing devname
If you do the following
mkfs.btrfs /dev/sdb /dev/sdc
rmmod btrfs
dd if=/dev/zero of=/dev/sdb bs=1M count=1
mount -o degraded /dev/sdc /mnt/btrfs-test
the box will panic trying to deref the name for the missing dev since it is
the lower numbered devid. So fix show_devname to not use missing devices.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Stefan Behrens [Wed, 1 Aug 2012 10:28:01 +0000 (04:28 -0600)]
Btrfs: fix that error value is changed by mistake
In iterate_inodes_from_logical() the error result from
extent_from_logical() is patched by mistake. Typically ENOENT is
patched to EINVAL because (-ENOENT & BTRFS_EXTENT_FLAG_TREE_BLOCK)
evaluates to true.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Josef Bacik [Tue, 31 Jul 2012 20:28:48 +0000 (16:28 -0400)]
Btrfs: lock extents as we map them in DIO
A deadlock in xfstests 113 was uncovered by commit
d187663ef24cd3d033f0cbf2867e70b36a3a90b8
This is because we would not return EIOCBQUEUED for short AIO reads, instead
we'd wait for the DIO to complete and then return the amount of data we
transferred, which would allow our stuff to unlock the remaning amount. But
with this change this no longer happens, so if we have a short AIO read (for
example if we try to read past EOF), we could leave the section from EOF to
the end of where we tried to read locked. Fixing this is tricky since there
is no clear way to know exactly how much data DIO truly submitted for IO, so
to make this less hard on ourselves and less combersome we need to lock the
extents as we try to map them, and then we unlock any areas we didn't
actually map. This makes us completely safe from deadlocks and reliance on
a particular behavior of the DIO code. This also lays the groundwork for
allowing us to use the normal csum storage method for reads which means we
can remove an allocation. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Dan Carpenter [Mon, 30 Jul 2012 08:10:44 +0000 (02:10 -0600)]
Btrfs: fix some endian bugs handling the root times
"trans->transid" is cpu endian but we want to store the data as little
endian. "item->ctime.nsec" is only 32 bits, not 64.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Dan Carpenter [Mon, 30 Jul 2012 08:15:15 +0000 (02:15 -0600)]
Btrfs: unlock on error in btrfs_delalloc_reserve_metadata()
We should release this mutex before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Dan Carpenter [Mon, 30 Jul 2012 08:15:43 +0000 (02:15 -0600)]
Btrfs: checking for NULL instead of IS_ERR
add_qgroup_rb() never returns NULL, only error pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Dan Carpenter [Mon, 30 Jul 2012 08:16:10 +0000 (02:16 -0600)]
Btrfs: fix some error codes in btrfs_qgroup_inherit()
These are returning zero when it should be returning a negative error
code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Stefan Behrens [Thu, 26 Jul 2012 09:40:35 +0000 (03:40 -0600)]
Btrfs: fix a misplaced address operator in a condition
This should obviously not be "if (&flag)" but "if (flag)".
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
This page took 0.051803 seconds and 5 git commands to generate.