Devin Heitmueller [Fri, 3 Apr 2009 01:24:38 +0000 (22:24 -0300)]
V4L/DVB (11795): xc5000: add build version to debug info
Expose the firmware build number along with the other version info
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Fri, 3 Apr 2009 01:14:51 +0000 (22:14 -0300)]
V4L/DVB (11794): au0828: reduce reset time for xc5000 to 10ms
The xc5000 datasheet indicates that the reset pin only needs to be held low
for 10ms. Reduce the value accordingly, which speeds up the firmware load
time a bit.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Fri, 3 Apr 2009 01:02:39 +0000 (22:02 -0300)]
V4L/DVB (11793): xc5000: Properly support power down for newer firmware
Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions.
Their technical support informed me that the correct way to put the tuner
to sleep is to pull the reset pin (but don't reload the firmware).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Fri, 3 Apr 2009 00:50:11 +0000 (21:50 -0300)]
V4L/DVB (11792): xc5000: switch to new version of Xceive firmware
This switches to a new version of the xc5000 firmware, extracted from the
latest Hauppauge driver. It includes the support for the XREG_BUSY register
(a lack of which was causing tuning to take 3200ms instead of around 300ms).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 16 Nov 2008 23:48:31 +0000 (20:48 -0300)]
V4L/DVB (11791): xc5000: do not sleep after digital tuning
Don't sleep for 400ms polling the tuner's lock if in digital mode (since the
xc5000 lock status registers appear to only be reliable in analog mode)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 16 Nov 2008 23:41:07 +0000 (20:41 -0300)]
V4L/DVB (11790): xc5000: restore sleep routine
Bring back the code that puts the xc5000 to sleep. For the Pinnacle 801e
this results in power consumption at idle dropping from 325ma to 124ma.
If there are *actually* any devices that don't work in this configuration,
they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's
suggestion)
Also, had to make sure we were making sure the firmware was loaded in the
digital version of set_params, or else we end up get i2c errors if the
device is asleep
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 16 Nov 2008 23:23:19 +0000 (20:23 -0300)]
V4L/DVB (11789): xc5000: check xc5000_readreg return value for XC_RESULT_SUCCESS
Make return value checking for calls to i2c routines explicit.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 16 Nov 2008 23:20:06 +0000 (20:20 -0300)]
V4L/DVB (11788): xc5000: cleanup i2c write routines
Cleanup the i2c write routine, getting rid of a passthrough function with only
one caller
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 16 Nov 2008 23:17:14 +0000 (20:17 -0300)]
V4L/DVB (11787): xc5000: cleanup i2c read routines
This patch centralizes the i2c read functions, and eliminates pass-through
function only called by one caller.
Make reading of xc5000 registers an atomic i2c transaction in case we're on a
multi-master bus.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Sun, 16 Nov 2008 02:29:11 +0000 (23:29 -0300)]
V4L/DVB (11786): xc5000: handle tuner reset failures properly
Properly handle tuner reset failures (before it was always returning success)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri Belimov [Mon, 11 May 2009 11:16:06 +0000 (08:16 -0300)]
V4L/DVB (11775): tuner: add support Philips MK5 tuner
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Tue, 12 May 2009 21:53:47 +0000 (18:53 -0300)]
V4L/DVB (11773): cx23885: clean up struct names for Hauppauge WinTV-HVR127X devices
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Tue, 12 May 2009 21:37:35 +0000 (18:37 -0300)]
V4L/DVB (11772): cx23885: update model matrix for "k2c2" retail boards
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Tue, 12 May 2009 20:32:17 +0000 (17:32 -0300)]
V4L/DVB (11771): cx23885: add DVB-T tuning support for Hauppauge WinTV-HVR1210
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Fri, 8 May 2009 19:05:29 +0000 (16:05 -0300)]
V4L/DVB (11770): cx23885: add ATSC/QAM tuning support for Hauppauge WinTV-HVR1255
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Sat, 9 May 2009 01:39:24 +0000 (22:39 -0300)]
V4L/DVB (11769): cx23885: add ATSC/QAM tuning support for Hauppauge WinTV-HVR1275
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 4 May 2009 02:27:02 +0000 (23:27 -0300)]
V4L/DVB (11768): cx23885: add ATSC/QAM tuning support for Hauppauge WinTV-HVR1270
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Sat, 2 May 2009 14:39:46 +0000 (11:39 -0300)]
V4L/DVB (11767): cx23885: Add preliminary support for the HVR1270
The patch means the board will be recognised, and the parts brought
out of reset correctly. This patches depends on the centralized GPIO
patch to be merged. What's missing before the HVR-1270 will function
for DTV? The model# needs to be added to avoid 'unknown model'
output and the LG3305/Tuner need to be attached in cx23885-dvb.c
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Mon, 11 May 2009 16:37:26 +0000 (13:37 -0300)]
V4L/DVB (11766): cx23885: mark functions encoder_on_port[bc] as static inline
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Sat, 2 May 2009 14:29:50 +0000 (11:29 -0300)]
V4L/DVB (11765): cx23885: Add generic functions for driving GPIO's
The GPIO's on the product can be in one of three places. To date we've
mainly used the GPIO's on the bridge itself, and once on the encoder.
Rather than having the complexity of multiple GPIO writes/reads from
isolated placed in the driver we'll route them through this function,
so we can make intelligent decisions about 1) Where the GPIO lives
and 2) Whether it conflicts (based on board) with some other function
to avoid bugs.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss [Thu, 30 Apr 2009 02:25:07 +0000 (23:25 -0300)]
V4L/DVB (11763): dvb-ttpci: Some whitespace adjustments
Some whitespace adjustments.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss [Thu, 30 Apr 2009 02:09:44 +0000 (23:09 -0300)]
V4L/DVB (11762): dvb-ttpci: Fixed return code of av7110_av_start_play
av7110_av_start_play() should return 0 on success.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss [Fri, 24 Apr 2009 02:24:33 +0000 (23:24 -0300)]
V4L/DVB (11761): dvb-ttpci: Fixed VIDEO_SLOWMOTION ioctl
Fixed VIDEO_SLOWMOTION ioctl.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss [Sun, 19 Apr 2009 17:47:01 +0000 (14:47 -0300)]
V4L/DVB (11760): dvb-ttpci: Check transport error indicator flag
Discard PES packet if transport error indicator flag is set.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss [Fri, 10 Apr 2009 13:20:00 +0000 (10:20 -0300)]
V4L/DVB (11759): dvb-ttpci: Add TS replay capability
Implemented TS replay capability.
audio/video devices are able to process PES and TS data now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap [Mon, 11 May 2009 16:37:41 +0000 (13:37 -0300)]
V4L/DVB (11758): 2: handle unregister for non-I2C builds
Build fails when CONFIG_I2C=n, so handle that case in the if block:
drivers/built-in.o: In function `v4l2_device_unregister':
(.text+0x157821): undefined reference to `i2c_unregister_device'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Tue, 5 May 2009 22:31:42 +0000 (19:31 -0300)]
V4L/DVB (11701): pvrusb2: Ensure the PVRUSB2 disabled the i2c gate on the tda10048.
... else DVB-T tuning will not work.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Tue, 5 May 2009 22:30:27 +0000 (19:30 -0300)]
V4L/DVB (11700): tda10048: Added option to block i2c gate control from other drivers.
Currently, DVB-T is broken and this fixes it.
The PVRUSB2 has an odd I2C bus configuration where opening the i2c gate
on the digital and analog demod causes the tuner to fail. This needs
to be protected against for the PVRUSB2.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 2 May 2009 15:06:15 +0000 (12:06 -0300)]
V4L/DVB (11677): radio-fm16: fix g_tuner.
g_tuner handled capability, audmode and rxsubchans incorrectly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 2 May 2009 15:04:13 +0000 (12:04 -0300)]
V4L/DVB (11676): radio-fm16: cleanups
Remove bogus flags field
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Randy Dunlap [Mon, 11 May 2009 17:51:32 +0000 (14:51 -0300)]
V4L/DVB (11756): soc_camera: depends on I2C
soc_camera uses i2c_*() functions and has build errors when CONFIG_I2C=n:
ERROR: "i2c_new_device" [drivers/media/video/soc_camera.ko] undefined!
ERROR: "i2c_get_adapter" [drivers/media/video/soc_camera.ko] undefined!
ERROR: "i2c_put_adapter" [drivers/media/video/soc_camera.ko] undefined!
ERROR: "i2c_unregister_device" [drivers/media/video/soc_camera.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 9 May 2009 03:43:40 +0000 (00:43 -0300)]
V4L/DVB (11753): tveeprom: Point the TCL MNM05-4 tuner entry to an actual tuner definition
The TCL MNM05-04 is used on some HVR-1600 models. It appears to be
similar to the TCL MFMN05-4 but without FM radio. The
TUNER_PHILIPS_FM1236_MK3 tuner definition appears to be the proper existing
tuner definition to use for this tuner.
Reported-by: Matt Beadon <matt.beadon@gmail.com>
Tested-by: Matt Beadon <matt.beadon@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 9 May 2009 03:34:31 +0000 (00:34 -0300)]
V4L/DVB (11752): cx18: Add missing newline to tuner detection error message
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 9 May 2009 21:00:23 +0000 (18:00 -0300)]
V4L/DVB (11750): pvrusb2: Allocate a routing ID for future support of Terratec Grabster AV400
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Sat, 2 May 2009 03:22:27 +0000 (00:22 -0300)]
V4L/DVB (11748): pvrusb2: Don't use the internal i2c client list
The i2c core used to maintain a list of client for each adapter. This
is a duplication of what the driver core already does, so this list
will be removed as part of a future cleanup. Anyone using this list
must stop doing so.
For pvrusb2, I propose the following change, which should lead to an
equally informative output. The only difference is that i2c clients
which are not a v4l2 subdev won't show up, but I guess this case is
not supposed to happen anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 2 May 2009 03:04:35 +0000 (00:04 -0300)]
V4L/DVB (11747): pvrusb2: Bump up version advertised through v4l interface
Kick up the pvrusb2 version number advertised through the v4l
interface. This value really has almost no meaning because I don't
make a serious attempt to version the driver in this manner (otherwise
this one line becomes a nasty hotspot of changes and merge
conflicts). The value that is here is really a historical thing.
However Hans Verkuil thought it might be a good idea to bump up the
number anyway right now since the driver's mechanism for communicating
with the v4l core has pretty much completely changed. Sending out a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 2 May 2009 01:33:16 +0000 (22:33 -0300)]
V4L/DVB (11746): pvrusb2: Set ir_video autoloading to default disabled
This sets the disable_autoload_ir_video module option to being set,
which disables any attempt by the driver to autoload IR support. This
changes preserves previous behavior, for now. This change can be set
back concurrent with other changes that finally update i2c-kbd-i2c to
use the new i2c binding model.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 2 May 2009 01:23:39 +0000 (22:23 -0300)]
V4L/DVB (11745): pvrusb2: Update to work with upcoming ir_video changes in v4l-dvb core
The ir-kbd-i2c module is about to be updated to match the new style
i2c binding model. These pvrusb2 changes maintain compatibility with
that change. Note that this does not actually break anything even
without the expected ir-kbd-i2c changes yet because previously the
pvrusb2 didn't autoload ir-kbd-i2c anyway.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Mon, 6 Apr 2009 04:51:38 +0000 (01:51 -0300)]
V4L/DVB (11744): pvrusb2: Select, track, and report IR scheme in use with the device
This change defines all possible "IR schemes" related to the pvrusb2
driver, on a per-device basis. That information is then set according
to the hardware in use. The idea here is to make possible a more
intelligent future decision on which, if any, IR receiver driver might
be loaded during initialization.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chaithrika U S [Thu, 7 May 2009 12:30:01 +0000 (09:30 -0300)]
V4L/DVB (11743): Analog Devices ADV7343 video encoder driver
Add ADV7343 I2C based video encoder driver. This follows the
v4l2-subdev framework. This driver has been tested on TI DM646x EVM. It
has been tested for Composite and Component outputs.
Updates as per review by Mauro Chehab, added support for more standards
supported by the encoder. Also adding the missed out signed-offs.Tested
only NTSC and PAL standards.
[hverkuil@xs4all.nl: s_routing API changed, updated driver to use new API]
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chaithrika U S [Thu, 7 May 2009 12:29:25 +0000 (09:29 -0300)]
V4L/DVB (11742): TI THS7303 video amplifier driver code
This patch adds driver for TI THS7303 video amplifier. This driver is
implemented as a v4l2 sub device. Tested on TI DM646x EVM.
This version has updates based on review comments by Mauro Chehab.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Roel Kluin [Sat, 2 May 2009 20:52:52 +0000 (17:52 -0300)]
V4L/DVB (11741): zoran: Fix &&/|| typo
Fix &&/|| typo. `default_norm' can be 0 (PAL), 1 (NTSC) or 2 (SECAM),
the condition tested was impossible.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Roel Kluin [Sat, 2 May 2009 19:38:47 +0000 (16:38 -0300)]
V4L/DVB: cleanup redundant tests on unsigned
Remove redundant tests on unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Greg Kroah-Hartman [Thu, 30 Apr 2009 22:18:08 +0000 (19:18 -0300)]
V4L/DVB (11739): remove driver_data direct access of struct device
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Thu, 30 Apr 2009 08:40:07 +0000 (05:40 -0300)]
V4L/DVB (11737): Drop stray references to i2c_probe
The new i2c binding model doesn't use i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Németh Márton [Wed, 29 Apr 2009 18:57:24 +0000 (15:57 -0300)]
V4L/DVB (11736): videobuf: modify return value of VIDIOC_REQBUFS ioctl
The V4L2 ioctls usually return 0 when the operation was successful
and -1 in case of error. Currently VIDIOC_REQBUFS returns the
number of buffers which is redundant because this information is
available in count field of struct v4l2_requestbuffers. The
V4L2 API specification, revision 0.24 [1] explicitly specifies for
VIDIOC_REQBUFS that the return value shall be 0 on success.
The patch was tested with v4l-test 0.13 [2] with vivi driver.
References:
[1] V4L2 API specification, revision 0.24
http://v4l2spec.bytesex.org/spec/r13696.htm
[2] v4l-test: Test environment for Video For Linux Two API
http://v4l-test.sourceforge.net/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pieter Van Schaik [Wed, 29 Apr 2009 06:55:31 +0000 (03:55 -0300)]
V4L/DVB (11735): Enables the Winfast TV2000 XP Global TV IR
Adds support to the remote control of the Winfast TV2000 XP Global TV
capture card. A case statement was added in order to initialize the
GPIO data structures as well as a case statement for handling the keys
correctly when pressed.
Thanks to Hermann and Mauro for all the help
Signed-off-by: Pieter C van Schaik <vansterpc@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri Belimov [Tue, 28 Apr 2009 09:46:15 +0000 (06:46 -0300)]
V4L/DVB (11734): remove hw reset of MPEG encoder when lost/found seq.
When we capture signal from composite input offen lost and found syncro
sequence. In this case the MPEG coder hardware reset after each
lost/found event. The image has a lot of artefactes. This patch remove
hardware reset of MPEG encoder.
This is patch from our customer. I checked this.
With my best regards, Dmitry.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri Belimov [Tue, 28 Apr 2009 09:41:08 +0000 (06:41 -0300)]
V4L/DVB (11733): increase MPEG encoder timout
If video has a lot of changes in frame, MPEG encoder need more time for
coding process. Add new bigger timeout for encoder.
This is patch from our customer. I checked this.
Signed-off-by: Alexey Osipov <lion-simba@pridelands.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
hermann pitton [Tue, 28 Apr 2009 22:44:05 +0000 (19:44 -0300)]
V4L/DVB (11732): saa7134: disable not yet existing IR and DVB support on the Compro T750
The Compro VideoMate T750 has no support for IR and DVB-T yet.
Disable both to avoid fall through and confusing printouts.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Magnus Damm [Tue, 28 Apr 2009 08:45:39 +0000 (05:45 -0300)]
V4L/DVB (11731): buf-dma-contig: remove sync operation
Remove the videobuf-dma-contig sync operation. Sync is only needed
for noncoherent buffers, and since videobuf-dma-contig is built on
coherent memory allocators the memory is by definition always in sync.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wen-chien Jesse Sung [Tue, 28 Apr 2009 04:11:22 +0000 (01:11 -0300)]
V4L/DVB (11730): af9015: support for KWorld MC810
Add USB ID (1b80:c810) for Kworld MC810.
Signed-off-by: Wen-chien Jesse Sung <jesse@cola.voip.idv.tw>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Roel Kluin [Sun, 26 Apr 2009 15:31:26 +0000 (12:31 -0300)]
V4L/DVB: cx23885/cymax2: binary/logical &/&& typo
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tobias Klauser [Sun, 26 Apr 2009 13:03:29 +0000 (10:03 -0300)]
V4L/DVB (11724): firedtv: Storage class should be before const qualifier
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Sun, 26 Apr 2009 08:43:59 +0000 (05:43 -0300)]
V4L/DVB (11723): Link firmware to physical device
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jani Monoses [Thu, 7 May 2009 06:32:27 +0000 (03:32 -0300)]
V4L/DVB (11720): gspca - sonixj: Webcam 06f8:3008 added
Signed-off-by: Jani Monoses <jani@ubuntu.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 5 May 2009 08:01:11 +0000 (05:01 -0300)]
V4L/DVB (11719): gspca - vc032x: mi1320_soc images are upside-down
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 5 May 2009 07:59:45 +0000 (04:59 -0300)]
V4L/DVB (11718): gspca - vc032x: Bad pixelformat for mi1320_soc
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sat, 9 May 2009 09:21:35 +0000 (06:21 -0300)]
V4L/DVB (11717): gspca - sonixj: Webcams with bridge sn9c128 added
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sun, 26 Apr 2009 17:46:12 +0000 (14:46 -0300)]
V4L/DVB (11716): gspca - sonixj: Adjust some exchanges according to traces
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Sat, 25 Apr 2009 16:29:01 +0000 (13:29 -0300)]
V4L/DVB (11715): gspca - main: Set the number of packets per ISOC message.
The number of packets per isochronous message may now be set by the subdrivers
(default value 32).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Thu, 23 Apr 2009 17:33:00 +0000 (14:33 -0300)]
V4L/DVB (11714): gspca - spca500 and sunplus: Change the 0x00 insertion mechanism.
The new mechanism does not use any temporary buffer.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Thu, 23 Apr 2009 16:52:27 +0000 (13:52 -0300)]
V4L/DVB (11713): gspca - ov534: Don't discard the images when no UVC EOF
A new image may start without any UVC EOF in the last packet of the
previous image.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 21 Apr 2009 17:05:44 +0000 (14:05 -0300)]
V4L/DVB (11712): gspca - main: Set the current alternate setting only when needed
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 21 Apr 2009 16:57:31 +0000 (13:57 -0300)]
V4L/DVB (11711): gspca - main: Fix a crash when no bandwidth available
When the bandwidth is not wide enough, the transfer endpoint may be set to
the one of the alternate setting 0. This one may be null and this causes a
divide by 0 oops.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 21 Apr 2009 16:45:56 +0000 (13:45 -0300)]
V4L/DVB (11710): gspca - main: Webcams cannot do both isoc and bulk image transfers.
Let the subdrivers to set the 'image transfer by bulk' flag.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 7 Apr 2009 08:30:31 +0000 (05:30 -0300)]
V4L/DVB (11709): gspca - zc3xx: Bad debug level in i2c_read
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-Francois Moine [Tue, 21 Apr 2009 07:17:59 +0000 (04:17 -0300)]
V4L/DVB (11708): gspca - main: Version change.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Guennadi Liakhovetski [Thu, 7 May 2009 16:25:32 +0000 (13:25 -0300)]
V4L/DVB (11705): soc-camera: prepare for the platform driver conversion
Add a platform driver to soc_camera.c. This way we preserve backwards
compatibility with existing platforms and can start converting them one by one
to the new platform-device soc-camera interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 3 May 2009 21:01:57 +0000 (18:01 -0300)]
V4L/DVB (11703): cx18: Have audio decoder drive SIF gain control, and rework AFE config
Ensure the variable gain amplifier gain for SIF is driven by the audio deocder
and not the video decoder. This forced rework of the analog front end (AFE)
configuration to not rely on autoconfiguration, but instead set up the AFE mux,
AFE parameters, and ADC1 & ADC2 configurations explicitly.
Reported-by: Helen Buus <mythtv@hbuus.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Sat, 2 May 2009 14:09:08 +0000 (11:09 -0300)]
V4L/DVB (11699): pvrusb2: Ensure we specify the I/F at attach time
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Sat, 2 May 2009 14:08:23 +0000 (11:08 -0300)]
V4L/DVB (11698): cx23885: For tda10048 boards ensure we specify the I/F
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Sat, 2 May 2009 14:07:29 +0000 (11:07 -0300)]
V4L/DVB (11697): tda10048: Add ability to select I/F at attach time.
tda10048: Add ability to select I/F at attach time.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Sun, 3 May 2009 18:51:36 +0000 (15:51 -0300)]
V4L/DVB (11695): gspca - stv06xx-vv6410: Set analog gain at init
Set the analog gain at sensor init. Also set a sensible default value.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Fri, 3 Apr 2009 20:16:42 +0000 (17:16 -0300)]
V4L/DVB (11694): gspca - stv06xx-vv6410: No need to double set gain and exposure
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Sun, 3 May 2009 18:45:48 +0000 (15:45 -0300)]
V4L/DVB (11693): gspca - stv06xx-vv6410: Add exposure ctrl
Add the possibility to control the exposure on the vv6410 sensor
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Sun, 3 May 2009 18:31:55 +0000 (15:31 -0300)]
V4L/DVB (11692): gspca - m5602: Checkpatch.pl fixes
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Tue, 10 Mar 2009 19:45:57 +0000 (16:45 -0300)]
V4L/DVB (11691): gspca - m5602-ov9650: Add ASUS A6K vflip quirk
The ASUS A6K needs the vflip quirk. Thanks to Marco Baldo for reporting
the issue.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Thu, 12 Feb 2009 19:36:05 +0000 (16:36 -0300)]
V4L/DVB (11690): gspca - m5602-s5k4aa: Add vflip quirk for the MSI L735
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Grégory Lardière [Thu, 12 Feb 2009 06:40:29 +0000 (03:40 -0300)]
V4L/DVB (11689): gspca - m5602-s5k4aa: Fixup the vflip/hflip
Ensure that the hflip and vflip is consistent when the sensor needs to
be vflip quirked or not.
Signed-off-by: Grégory Lardière <spmf2004-m560x@yahoo.fr>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Grégory Lardière [Thu, 12 Feb 2009 06:32:52 +0000 (03:32 -0300)]
V4L/DVB (11688): gspca - m5602-s5k4aa: Fixup SXGA resolution.
The SXGA resolution doesn't work unless you first force the VGA resolution.
More investigation is needed in order to fix this the "right" way.
Signed-off-by: Grégory Lardière <spmf2004-m560x@yahoo.fr>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Mon, 2 Feb 2009 19:08:06 +0000 (16:08 -0300)]
V4L/DVB (11687): gspca - m5602-ov9650: Add missing v4l2 ctrl ids
Red and blue balance missed their id fields
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Mon, 2 Feb 2009 18:56:39 +0000 (15:56 -0300)]
V4L/DVB (11686): gspca - m5602-s5k4aa: Disable SXGA resolution for now
SXGA resolution needs more testing. Disable it for now
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Mon, 2 Feb 2009 06:51:20 +0000 (03:51 -0300)]
V4L/DVB (11685): gspca - gspca-m5602: Constify parameters of two functions
A number of parameters to some functions in the m5602 are constant and should be flagged as such.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Thu, 29 Jan 2009 16:34:41 +0000 (13:34 -0300)]
V4L/DVB (11684): gspca - m5602-s5k4aa: Add experimental SXGA support
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manu Abraham [Sat, 2 May 2009 21:26:58 +0000 (18:26 -0300)]
V4L/DVB (11682): STV0900/STV0903: Add support for Silicon cut >= 3
1. Support Silicon Cut >= 3.0
2. Remove support for obsolete cuts: 1.0. 1.1. 1.2
3. Try to catch more error cases
Driver doesn't now attach to obsolete silcon cuts, It just simply quits.
Results in code simplification, with removal of the obsolete cuts.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 2 May 2009 13:58:51 +0000 (10:58 -0300)]
V4L/DVB (11673): v4l2-device: unregister i2c_clients when unregistering the v4l2_device.
Until now I relied on i2c_del_adapter to unregister the i2c_clients for
me, however, if the i2c bus is a platform bus then it is never deleted.
So instead I need to unregister i2c clients when unregistering the
v4l2_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 2 May 2009 13:15:17 +0000 (10:15 -0300)]
V4L/DVB (11672): ivtv: use v4l2_device_set_name.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 2 May 2009 13:12:50 +0000 (10:12 -0300)]
V4L/DVB (11671): v4l2: add v4l2_device_set_name()
Add a utility function that can be used to setup the v4l2_device's name
field in a standard manner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 2 May 2009 12:42:57 +0000 (09:42 -0300)]
V4L/DVB (11670): tuner: remove tuner_i2c_address_check
Support for tuners with i2c addresses >= 0x65 is dropped since no tuners
with addresses in the range 0x65-0x6f have been found.
This patch removes addresses 0x65-0x6f from the list of tuner probe addresses,
it removes the kernel warning that warned if addresses in this range appeared,
and it removed a hack for the cx88 that is no longer needed now that the
tuner address range is reduced.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Wed, 29 Apr 2009 23:49:12 +0000 (20:49 -0300)]
V4L/DVB (11666): cx23885: Don't assume GPIO interrupts are cam related.
cx23885: Don't assume GPIO interrupts are cam related.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Sat, 28 Mar 2009 17:22:21 +0000 (14:22 -0300)]
V4L/DVB (11665): cx88: Add support for the Hauppauge IROnly board.
cx88: Add support for the Hauppauge IROnly board.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 5 May 2009 09:39:21 +0000 (06:39 -0300)]
V4L/DVB (11663): Fix a warning introduced by git commit
ec5f5bf80501abfe2da2897cfcde8452b545aacb
/home/v4l/master/v4l/radio-si470x.c: In function 'si470x_fops_release':
/home/v4l/master/v4l/radio-si470x.c:1218: warning: label 'unlock' defined but not used
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Wed, 29 Apr 2009 21:03:27 +0000 (18:03 -0300)]
V4L/DVB (11654a): Add a missing end of line at the end of gspca/m5602/Makefile
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tobias Klauser [Sun, 26 Apr 2009 12:30:18 +0000 (09:30 -0300)]
V4L/DVB (11654): gspca - m5602: Storage class should be before const qualifier
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
[mchehab@redhat.com: Fix a trivial merge conflict]
Cc: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Wed, 28 Jan 2009 16:14:34 +0000 (13:14 -0300)]
V4L/DVB (11650): gspca - m5602: Sort out macro conflict by adding a prefix
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Mon, 27 Apr 2009 18:41:45 +0000 (15:41 -0300)]
V4L/DVB (11649): gspca - m5602: Probe the ov7660 sensor
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Wed, 28 Jan 2009 07:02:49 +0000 (04:02 -0300)]
V4L/DVB (11648): gspca - m5602: Remove some needless error checking and add comments
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Wed, 28 Jan 2009 06:34:02 +0000 (03:34 -0300)]
V4L/DVB (11647): gspca - m5602-po1030: Disable QVGA for now
Getting QVGA to be supported on the po1030 seems harder than I first thought. I need access to the proper hardware in order to fix it up.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Erik Andrén [Wed, 28 Jan 2009 06:29:51 +0000 (03:29 -0300)]
V4L/DVB (11646): gspca - m5602-mt9m111: Disable QVGA until it has been verified to work
The QVGA resolution currently hasn't been verified to work. Disable it for now.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This page took 0.043123 seconds and 5 git commands to generate.