Helmut Schaa [Mon, 21 Mar 2011 14:07:55 +0000 (15:07 +0100)]
mac80211: Minor optimization in tx status handling
ieee80211_tx_status iterates over all tx rates the driver reports back
in order to
1) mark tx rates as invalid if the driver cannot have tried that rate
2) find the actually used tx rate for the final retransmission
By leaving the for loop when the first invalid rate index is found we
can move the rates_idx assignment after the loop and therefore save
a few assignments and conditionals.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 19 Mar 2011 12:55:43 +0000 (13:55 +0100)]
ath9k: remove the pending frames ath_txq_schedule workaround
This workaround called ath_txq_schedule whenever there were still pending
frames for a queue, but the queue depth was zero. Because of its its high
false positive probability (e.g. with paused TIDs) and because it is in
the way of other pending work (AP powersave fixes), it is better to remove
this code entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 19 Mar 2011 12:55:42 +0000 (13:55 +0100)]
ath9k_hw: force rx chainmask to 7 on AR9100
Most AR9100 devices already have a chainmask of 7 (three antennas), however
on the ones that don't (rx and tx chainmask set to 5), problems with IQ
mismatch calibration have been observed.
This shows up as tx queue hangs (and subsequent hardware resets) if traffic
is sent during this type of calibration.
Forcing the rx chainmask to 7 fixes the calibration issues with no apparent
negative side effects on throughput and stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 19 Mar 2011 12:55:41 +0000 (13:55 +0100)]
ath9k_hw: enable a BlockAck related fixup specific to AR9100
Fixes interop issues with aggregation in combination with multi-BSSID
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 19 Mar 2011 12:55:40 +0000 (13:55 +0100)]
ath9k: add support for overriding LED pin and GPIO settings from platform data
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 19 Mar 2011 12:55:39 +0000 (13:55 +0100)]
ath9k: add support for overriding the MAC address through platform data
On some devices the correct MAC address is not in the EEPROM data, but
stored somewhere else.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 19 Mar 2011 12:55:38 +0000 (13:55 +0100)]
ath9k: add an interface for overriding the value of specific GPIO pins
Some devices control antenna settings or other things through GPIO pins
of the wireless interface. Add a debugfs interface for changing those
and keeping them set across card resets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 19 Mar 2011 12:55:37 +0000 (13:55 +0100)]
ath9k: remove unnecessary debugfs return code checks
Since the ath9k debugfs directory is cleaned up by debugfs_remove_recursive,
there's no point in checking the return code of every single debugfs create
line.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 18 Mar 2011 02:53:01 +0000 (21:53 -0500)]
rtlwifi: rtl8192c{e,u}: Remove some extraneous casts on memcpy commands
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Thu, 17 Mar 2011 18:58:49 +0000 (11:58 -0700)]
mwl8k: Queue ADDBA requests in respective data queues
Queue ADDBA requests in respective data queues to avoid ADDBA
requests and the the related data packets (to the same ra/tid)
queued in the hardware to be sent out asynchronously.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Thu, 17 Mar 2011 18:58:48 +0000 (11:58 -0700)]
mwl8k: Check outgoing rate for a station to decide if ampdu can be created
If the outgoing packet rate to a particular HT station is <=6.5
Mbps, do not attempt to create an ampdu. Also, if the outgoing
rate is legacy rate, do not create an ampdu.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Thu, 17 Mar 2011 18:58:47 +0000 (11:58 -0700)]
mwl8k: Handle the watchdog event from the firmware
When an ampdu stream is on, if the firmware rate adaptation
logic decides that the outgoing packet rate to the station needs
to go below 6.5Mbps (non HT rate), it sends an event indicating that
the ampdu stream needs to be destroyed. Handle this event in the driver
and destroy the ampdu stream so that the rate can go below 6.5Mbps
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Thu, 17 Mar 2011 18:58:46 +0000 (11:58 -0700)]
mwl8k: Initiate BA sessions
Specifically, handle ampdu_action and attempt to start a BA
session on receiving the first qos packet from mac80211 for
transmission to a HT sta. While the BA session is being created,
all the packets belonging to that stream will be dropped to
prevent sequence number mismatch at the recipient.
Contains contributions from:
Yogesh Powar <yogeshp@marvell.com>
Pradeep Nemavat <pnemavat@marvell.com>
Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brian Cavagnolo [Thu, 17 Mar 2011 18:58:45 +0000 (11:58 -0700)]
mwl8k: add internal API for managing AMPDU streams
In particular, we can now add, start, lookup, and remove streams.
Based on work by Nishant Sarmukadam <nishants@marvell.com> and
Pradeep Nemavat <pnemavat@marvell.com>.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brian Cavagnolo [Thu, 17 Mar 2011 18:58:44 +0000 (11:58 -0700)]
mwl8k: differentiate between WMM queues and AMPDU queues
We now have two different kinds of queues. And the number of
AMPDU queues may vary. So we must be clear about which queues we
are dealing with. Note that when we report the number of queues
to mac80211, we only report the WMM queues.
Based on work by Yogesh Powar <yogeshp@marvell.com>.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Thu, 17 Mar 2011 18:58:43 +0000 (11:58 -0700)]
mwl8k: add support for block ack commands
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brian Cavagnolo [Thu, 17 Mar 2011 18:58:42 +0000 (11:58 -0700)]
mwl8k: update to ap firmware API version 2
Firmware APIv2 adds the following enhancements:
-- capabilities are reported by the firmware
-- API supports up to 8 dedicated AMPDU streams
-- optional packet timestamping and expiration can be enabled.
Specifically, packets that are queued in firmware for longer
than 500ms will be dropped if this option is used.
Based on work by "Nishant Sarmukadam" <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brian Cavagnolo [Thu, 17 Mar 2011 18:58:41 +0000 (11:58 -0700)]
mwl8k: refactor in preparation for APIv2 update
Specifically, APIv2 will specify a variable number of AMPDU
queues in the MWL8K_CMD_GET_HW_SPEC. So init the tx queues after
MWL8K_CMD_GET_HW_SPEC for ap fw.
Also, we make it safe to deinit queues that have not been init'd.
This happens if the mwl8k_get_hw_spec_ap routine fails, for
example.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 15 Mar 2011 22:17:01 +0000 (23:17 +0100)]
mac80211: add comment about reordering
Took me a minute to figure this out, maybe
it's better documented...
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Tue, 15 Mar 2011 17:41:35 +0000 (23:11 +0530)]
ath9k_hw: Speedup register ops for HTC driver
Fine-tuning register write operation and avoid unnecessay
delays for ath9k_htc driver, saves hw reset time which
improves scanning time and also solves one of the following
scenario.
Sometimes the ACK is sent by STA for assoc response is not
seen at AP side. So the AP continues to send retry assoc
responses. At the STA side, since the assoc response was
already forwarded to mac80211, it proceeded to channel change
which in turns does chip reset.
In most of the cases the chip reset was completed before
max retries are reached at AP side. Hence STA can able to ACK
the retried frames again. But in clear environment these retries
are completed within shortspan of time.
Since ath9k_htc consumes more time for hw reset, this latency
is causing dissociation by AP due to max reties are reached.
This issue was originally reported with Cisco Aironet 1250 AP
in HT40 mode in noise free environment.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Tue, 15 Mar 2011 14:25:38 +0000 (19:55 +0530)]
ath: Speedup key set/reset ops for HTC driver
By enabling buffered register write for ath9k_htc driver
avoids unnecessary dissociation while rekeying phase under
heavy traffic exchange.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Tue, 15 Mar 2011 14:25:36 +0000 (19:55 +0530)]
ath9k_hw: Fix throughput drops in HT40 mode for AR9287 chips
Doing adc gain calibration for AR9287 chips is causing
throughput drops in HT40 mode. Remove ADC Gain from supported
calibration list.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Tue, 15 Mar 2011 14:25:35 +0000 (19:55 +0530)]
ath9k_htc: Fix LED pin for AR9287 HTC device
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Tue, 15 Mar 2011 07:03:24 +0000 (10:03 +0300)]
iwlwifi: remove duplicate initialization in __iwl_down()
We initialize exit_pending twice. It's the second initialization which
is correct. That was added in
d745d472af "iwlwifi: cancel scan when
down the device".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Tue, 29 Mar 2011 19:09:47 +0000 (12:09 -0700)]
Linux 2.6.39-rc1
Linus Torvalds [Tue, 29 Mar 2011 19:09:30 +0000 (12:09 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
Linus Torvalds [Tue, 29 Mar 2011 18:43:30 +0000 (11:43 -0700)]
Merge branch 'frv' of git://git./linux/kernel/git/dhowells/linux-2.6-frv
* 'frv' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-frv:
FRV: Use generic show_interrupts()
FRV: Convert genirq namespace
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
frv: Convert cpu irq_chip to new functions
frv: Convert mb93493 irq_chip to new functions
frv: Convert mb93093 irq_chip to new function
frv: Convert mb93091 irq_chip to new functions
frv: Fix typo from __do_IRQ overhaul
frv: Remove stale irq_chip.end
FRV: Do some cleanups
FRV: Missing node arg in alloc_thread_info_node() macro
NOMMU: implement access_remote_vm
NOMMU: support SMP dynamic percpu_alloc
NOMMU: percpu should use is_vmalloc_addr().
Linus Torvalds [Tue, 29 Mar 2011 18:36:52 +0000 (11:36 -0700)]
Merge branch 'stable/bug-fixes-rc1' of git://git./linux/kernel/git/konrad/xen
* 'stable/bug-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Use new irq_move functions
xen: Convert genirq namespace
xen: fix p2m section mismatches
xen/p2m: Allocate p2m tracking pages on override
xen-gntdev: unlock on error path in gntdev_mmap()
xen-gntdev: return -EFAULT on copy_to_user failure
Linus Torvalds [Tue, 29 Mar 2011 18:20:09 +0000 (11:20 -0700)]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: softdog.c: enhancement to optionally invoke panic instead of reboot on timer expiry
watchdog: fix nv_tco section mismatch
watchdog: sp5100_tco.c: Check if firmware has set correct value in tcobase.
watchdog: Convert release_resource to release_region/release_mem_region
watchdog: s3c2410_wdt.c: Convert release_resource to release_region/release_mem_region
Linus Torvalds [Tue, 29 Mar 2011 18:11:18 +0000 (11:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bp/bp
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Fix potential memleak
Linus Torvalds [Tue, 29 Mar 2011 17:46:15 +0000 (10:46 -0700)]
Merge branch 'irq-final-for-linus-v2' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'irq-final-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (111 commits)
gpio: ab8500: Mark broken
genirq: Remove move_*irq leftovers
genirq: Remove compat code
drivers: Final irq namespace conversion
mn10300: Use generic show_interrupts()
mn10300: Cleanup irq_desc access
mn10300: Convert genirq namespace
frv: Use generic show_interrupts()
frv: Convert genirq namespace
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
frv: Convert cpu irq_chip to new functions
frv: Convert mb93493 irq_chip to new functions
frv: Convert mb93093 irq_chip to new function
frv: Convert mb93091 irq_chip to new functions
frv: Fix typo from __do_IRQ overhaul
frv: Remove stale irq_chip.end
m68k: Convert irq function namespace
xen: Use new irq_move functions
xen: Cleanup genirq namespace
unicore32: Use generic show_interrupts()
...
Peter Huewe [Tue, 29 Mar 2011 11:31:25 +0000 (13:31 +0200)]
char/tpm: Fix unitialized usage of data buffer
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Borislav Petkov [Tue, 29 Mar 2011 16:10:53 +0000 (18:10 +0200)]
amd64_edac: Fix potential memleak
We check the pointers together but at least one of them could be invalid
due to failed allocation. Since we cannot continue if either of the two
allocations has failed, exit early by freeing them both.
Cc: <stable@kernel.org> # 38.x
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Dave Chinner [Tue, 29 Mar 2011 07:08:50 +0000 (18:08 +1100)]
fs: don't use igrab() while holding i_lock
Fix the incorrect use of igrab() inside the i_lock in NFS and Ceph‥
If we are already holding the i_lock, we have a reference to the
inode so we can safely use ihold() to gain an extra reference. This
avoids hangs due to lock recursion on the i_lock now that the
inode_lock is gone and igrab() uses the i_lock itself.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 29 Mar 2011 14:41:33 +0000 (07:41 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
xfrm: Restrict extended sequence numbers to esp
xfrm: Check for esn buffer len in xfrm_new_ae
xfrm: Assign esn pointers when cloning a state
xfrm: Move the test on replay window size into the replay check functions
netdev: bfin_mac: document TE setting in RMII modes
drivers net: Fix declaration ordering in inline functions.
cxgb3: Apply interrupt coalescing settings to all queues
net: Always allocate at least 16 skb frags regardless of page size
ipv4: Don't ip_rt_put() an error pointer in RAW sockets.
net: fix ethtool->set_flags not intended -EINVAL return value
mlx4_en: Fix loss of promiscuity
tg3: Fix inline keyword usage
tg3: use <linux/io.h> and <linux/uaccess.h> instead <asm/io.h> and <asm/uaccess.h>
net: use CHECKSUM_NONE instead of magic number
Net / jme: Do not use legacy PCI power management
myri10ge: small rx_done refactoring
bridge: notify applications if address of bridge device changes
ipv4: Fix IP timestamp option (IPOPT_TS_PRESPEC) handling in ip_options_echo()
can: c_can: Fix tx_bytes accounting
can: c_can_platform: fix irq check in probe
...
Thomas Gleixner [Thu, 24 Mar 2011 20:37:31 +0000 (21:37 +0100)]
xen: Use new irq_move functions
These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Thomas Gleixner [Fri, 25 Mar 2011 10:01:39 +0000 (11:01 +0100)]
xen: Convert genirq namespace
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Randy Dunlap [Thu, 24 Mar 2011 20:34:32 +0000 (13:34 -0700)]
xen: fix p2m section mismatches
Fix section mismatch warnings:
set_phys_range_identity() is called by __init xen_set_identity(),
so also mark set_phys_range_identity() as __init.
then:
__early_alloc_p2m() is called set_phys_range_identity(), so also mark
__early_alloc_p2m() as __init.
WARNING: arch/x86/built-in.o(.text+0x7856): Section mismatch in reference from the function __early_alloc_p2m() to the function .init.text:extend_brk()
The function __early_alloc_p2m() references
the function __init extend_brk().
This is often because __early_alloc_p2m lacks a __init
annotation or the annotation of extend_brk is wrong.
WARNING: arch/x86/built-in.o(.text+0x7967): Section mismatch in reference from the function set_phys_range_identity() to the function .init.text:extend_brk()
The function set_phys_range_identity() references
the function __init extend_brk().
This is often because set_phys_range_identity lacks a __init
annotation or the annotation of extend_brk is wrong.
[v2: Per Stephen Hemming recommonedation made __early_alloc_p2m static]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
FRV: Use generic show_interrupts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
FRV: Convert genirq namespace
Convert to new function names. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
All chips converted
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
frv: Convert cpu irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
frv: Convert mb93493 irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
frv: Convert mb93093 irq_chip to new function
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
frv: Convert mb93091 irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:13 +0000 (14:05 +0100)]
frv: Fix typo from __do_IRQ overhaul
Compiles way better.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Tue, 29 Mar 2011 13:05:12 +0000 (14:05 +0100)]
frv: Remove stale irq_chip.end
irq_chip.end got obsolete with the removal of __do_IRQ().
irq-mb93093.c even lacks an implementation, but nobody noticed that
it's broken since commit 88d6e1 in 2006.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Amerigo Wang [Tue, 29 Mar 2011 13:05:12 +0000 (14:05 +0100)]
FRV: Do some cleanups
1. frv doesn't support SMP, remove the useless SMP bits.
2. frv has its own alloc_task_struct, so define __HAVE_ARCH_TASK_STRUCT_ALLOCATOR
(I am not sure if frv should use generic alloc_task_struct().)
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 29 Mar 2011 13:05:12 +0000 (14:05 +0100)]
FRV: Missing node arg in alloc_thread_info_node() macro
There are two alloc_thread_info_node() macros defined (one for debugging and
one for normal). The commit that changed them most recently:
commit
b6a84016bd2598e35ead635147fa53619982648d
Author: Eric Dumazet <eric.dumazet@gmail.com>
Date: Tue Mar 22 16:30:42 2011 -0700
Subject: mm: NUMA aware alloc_thread_info_node()
didn't add the node argument into the macro argument list for the normal macro.
This results in the following error:
kernel/fork.c:267:39: error: macro "alloc_thread_info_node" passed 2 arguments, but takes just 1
kernel/fork.c: In function 'dup_task_struct':
kernel/fork.c:267: error: 'alloc_thread_info_node' undeclared (first use in this function)
kernel/fork.c:267: error: (Each undeclared identifier is reported only once
kernel/fork.c:267: error: for each function it appears in.)
Signed-off-by: David Howells <dhowells@redhat.com>
Mike Frysinger [Tue, 29 Mar 2011 13:05:12 +0000 (14:05 +0100)]
NOMMU: implement access_remote_vm
Recent vm changes brought in a new function which the core procfs code
utilizes. So implement it for nommu systems too to avoid link failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Simon Horman <horms@verge.net.au>
Tested-by: Ithamar Adema <ithamar.adema@team-embedded.nl>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Thomas Gleixner [Tue, 29 Mar 2011 02:02:50 +0000 (04:02 +0200)]
gpio: ab8500: Mark broken
This driver is broken in several aspects.
1) old style irq_chip functions. Sigh
2) Abuse of the unlock callback. That's not supposed to be a state
machine for evrything and some more.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Tue, 29 Mar 2011 00:51:13 +0000 (02:51 +0200)]
genirq: Remove move_*irq leftovers
All users converted to new interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Mon, 28 Mar 2011 11:32:20 +0000 (13:32 +0200)]
genirq: Remove compat code
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Mon, 28 Mar 2011 15:49:12 +0000 (17:49 +0200)]
drivers: Final irq namespace conversion
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 17:54:24 +0000 (18:54 +0100)]
mn10300: Use generic show_interrupts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 16:36:37 +0000 (17:36 +0100)]
mn10300: Cleanup irq_desc access
The migration needs only access to irq_data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 16:35:56 +0000 (17:35 +0100)]
mn10300: Convert genirq namespace
Convert to new function names. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 17:48:36 +0000 (18:48 +0100)]
frv: Use generic show_interrupts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 15:38:49 +0000 (16:38 +0100)]
frv: Convert genirq namespace
Convert to new function names. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:39 +0000 (20:20 +0100)]
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
All chips converted
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <
20110206192106.
601290592@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:38 +0000 (20:20 +0100)]
frv: Convert cpu irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <
20110206192106.
501651128@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:37 +0000 (20:20 +0100)]
frv: Convert mb93493 irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <
20110206192106.
401266547@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:36 +0000 (20:20 +0100)]
frv: Convert mb93093 irq_chip to new function
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <
20110206192106.
300303769@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:35 +0000 (20:20 +0100)]
frv: Convert mb93091 irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <
20110206192106.
203431646@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:34 +0000 (20:20 +0100)]
frv: Fix typo from __do_IRQ overhaul
Compiles way better.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <
20110206192106.
109992056@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:33 +0000 (20:20 +0100)]
frv: Remove stale irq_chip.end
irq_chip.end got obsolete with the removal of __do_IRQ().
irq-mb93093.c even lacks an implementation, but nobody noticed that
it's broken since commit 88d6e1 in 2006.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <
20110206192106.
011224503@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Mon, 28 Mar 2011 11:31:17 +0000 (13:31 +0200)]
m68k: Convert irq function namespace
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 20:31:25 +0000 (21:31 +0100)]
xen: Use new irq_move functions
These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Thomas Gleixner [Fri, 25 Mar 2011 09:58:06 +0000 (10:58 +0100)]
xen: Cleanup genirq namespace
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 17:26:42 +0000 (18:26 +0100)]
unicore32: Use generic show_interrupts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 17:26:16 +0000 (18:26 +0100)]
unicore32: Convert to new irq function names
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 17:03:13 +0000 (18:03 +0100)]
sparc: Use generic show_interrupts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org
Thomas Gleixner [Thu, 24 Mar 2011 16:52:54 +0000 (17:52 +0100)]
sparc: Convert to new irq function names
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org
Thomas Gleixner [Thu, 24 Mar 2011 16:57:12 +0000 (17:57 +0100)]
sparc: Cleanup direct irq_desc access
Use the proper wrapper functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org
Thomas Gleixner [Thu, 24 Mar 2011 08:03:45 +0000 (09:03 +0100)]
sparc: Use the new genirq functionality
Make use of the new features in genirq:
1) Set the chip flag IRCHIP_EOI_IF_HANDLED, which ensures in the
core code that irq_eoi() is only called when the interrupt was
handled. That removes the extra status check in the callback.
2) Use the preflow handler, which is called from the fasteoi core code
before the device handler. That avoids another status check and the
open coded handler redirection.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: sparclinux@vger.kernel.org
Thomas Gleixner [Thu, 24 Mar 2011 15:31:17 +0000 (16:31 +0100)]
sh: Convert to new function names
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 13:47:46 +0000 (14:47 +0100)]
sh: Use the proper accessor functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 16:04:59 +0000 (17:04 +0100)]
powerpc: Use generic show_interrupts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:45:20 +0000 (16:45 +0100)]
powerpc: Convert to new irq_* function names
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:36:35 +0000 (16:36 +0100)]
powerpc: irq: Use irqdata based information
We want to tighten the irq_desc access. So use the new accessors for
the same information.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Mon, 28 Mar 2011 14:46:02 +0000 (16:46 +0200)]
powerpc-fsl-msi-use-irqd.patch
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:26:01 +0000 (16:26 +0100)]
powerpc: xilinx: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates the LEVEL flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:23:57 +0000 (16:23 +0100)]
powerpc: uic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates IRQ_LEVEL.
Use irq_data to get the level type information in the chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:20:15 +0000 (16:20 +0100)]
powerpc: mpic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Retrieve the IRQ_LEVEL information from irq_data which avoids a
redundant sparse irq lookup as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:18:32 +0000 (16:18 +0100)]
powerpc: mpc8xx_pic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The level flag is
updated in the core as well.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:16:30 +0000 (16:16 +0100)]
powerpc: ipic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:13:38 +0000 (16:13 +0100)]
powerpc: cpm2_pic: Use IRQCHIP_EOI_IF_HANDLED
The core code provides the same functionality when the
IRQCHIP_EOI_IF_HANDLED flag is set for the irq chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:07:51 +0000 (16:07 +0100)]
powerpc: cpm2_pic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:04:41 +0000 (16:04 +0100)]
powerpc: cell: Fix the irq_desc access
The core irq_set_type() function updates the flow type when the chip
callback returns 0. It also updates irq_data, so this can be used in
irq_ack() to check for the level bit. That avoids a redundant sparse
irq lookup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:03:07 +0000 (16:03 +0100)]
powerpc: mac: pic: Use irqd_is_level_type()
No need for a redundant sparse irq lookup. irqdata provides the same
information.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 14:54:03 +0000 (15:54 +0100)]
powerpc: media5200: Remove pointless set_irq_type()
The irq chip has no irq_set_type() callback. So calling the call is
pointless. Set IRQ_LEVEL via the proper accessor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 14:43:57 +0000 (15:43 +0100)]
powerpc: Use proper accessors for IRQ_* flags
Use the proper accessors instead of open access to irq_desc.
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Mon, 28 Mar 2011 11:47:54 +0000 (13:47 +0200)]
parisc: Use irq_to_desc() in show_interrupts()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 16:41:44 +0000 (17:41 +0100)]
parisc: Convert irq namespace
Convert to the new function names. Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Thomas Gleixner [Thu, 24 Mar 2011 16:48:47 +0000 (17:48 +0100)]
parisc: Convert the final irq bits
1) As promised in the comment, the core does not copy cpumask anymore
when the arch code returns -EINVAL
2) Get the per cpu information from irq_data
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: linux-parisc@vger.kernel.org
Thomas Gleixner [Mon, 28 Mar 2011 11:59:54 +0000 (13:59 +0200)]
mips: vr41xx: Use irdq_irq_disabled()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 27 Mar 2011 13:19:28 +0000 (15:19 +0200)]
MIPS: Convert the irq functions to the new names
Scripted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 27 Mar 2011 13:11:13 +0000 (15:11 +0200)]
MIPS: alchemy: Use proper irq accessors
This really starts to be a sysiphean task.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 27 Mar 2011 14:04:30 +0000 (16:04 +0200)]
MIPS: Octeon: Simplify irq_cpu_on/offline irq chip functions
Make use of the IRQCHIP_ONOFFLINE_ENABLED flag and remove the
wrappers. Use irqd_irq_disabled() instead of desc->status, which will
go away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: David Daney <ddaney@caviumnetworks.com>
David Daney [Fri, 25 Mar 2011 19:38:51 +0000 (12:38 -0700)]
MIPS: Octeon: Rewrite interrupt handling code.
This includes conversion to new style irq_chip functions, and
correctly enabling/disabling per-CPU interrupts.
The hardware interrupt bit to irq number mapping is now done with a
flexible map, instead of by bit twiddling the irq number.
[ tglx: Adjusted to new irq_cpu_on/offline callbacks and
__irq_set_affinity_lock ]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org
LKML-Reference: <
1301081931-11240-5-git-send-email-ddaney@caviumnetworks.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This page took 0.043186 seconds and 5 git commands to generate.