Dor Shaish [Mon, 26 Mar 2012 15:20:55 +0000 (08:20 -0700)]
iwlwifi: Disabling calibrations variable
Add a variable for disabling specific calibrations.
Merged old variables for calibrations disabling.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Emmanuel Grumbach [Tue, 20 Mar 2012 12:50:09 +0000 (14:50 +0200)]
iwlwifi: remove uneeded include from iwl-pci.c
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
David Spinadel [Tue, 13 Mar 2012 12:46:38 +0000 (14:46 +0200)]
iwlwifi: remove double verification of ucode sections
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
David Spinadel [Tue, 13 Mar 2012 12:32:48 +0000 (14:32 +0200)]
iwlwifi: set size of ucode section
Set size of firmware section in mvm bundle format.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 23 Mar 2012 15:37:30 +0000 (08:37 -0700)]
iwlwifi: remove iwl_tx_queue declaration
The declaration isn't needed as the struct is only
used in code that includes the right header file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Fri, 23 Mar 2012 15:34:31 +0000 (08:34 -0700)]
iwlwifi: move status definitions from iwl-shared
The code has been changed, move the definitions to the proper file
being used by the code.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Amit Beka [Sun, 19 Feb 2012 09:07:46 +0000 (11:07 +0200)]
iwlwifi: added HBUS_TARG_TEST_REG
This register is used to enable some debug mechanisms.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Tue, 20 Mar 2012 23:36:54 +0000 (16:36 -0700)]
iwlwifi: move HCMD_ACTIVE to trans
The HCMD_ACTIVE bit is only used in trans.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Tue, 20 Mar 2012 17:33:34 +0000 (10:33 -0700)]
iwlwifi: complete STATUS_READY refactoring
When WiMax takes over the RF, inform the op_mode.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 9 Mar 2012 08:42:52 +0000 (09:42 +0100)]
iwlwifi: remove antenna from mod params struct
It doesn't even exist as a module parameter,
so just remove the item from the struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 9 Mar 2012 08:16:35 +0000 (09:16 +0100)]
iwlwifi: remove uCode alternatives mechanism
We've never released firmware using the alternatives
mechanism and our build process makes that difficult
anyway. This means that in every file we have ever
built (except maybe by hand for testing) the listed
alternative was 0. Make the alternative field in the
TLVs part of the TLV number (thus expanding that to
32 bits); this gives us more TLV numbers (not really
needed) and more importantly protects against rogue
firmware files that actually do use the alternatives
mechanism -- those will now be rejected since they
don't contain any valid TLVs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 9 Mar 2012 07:58:46 +0000 (08:58 +0100)]
iwlwifi: remove no_sleep_autoadjust
My original idea with this was to adjust the sleep
pattern of the uCode based on the maximum network
latency userspace asked for. Due to nobody wanting
to test it, this logic was disabled by default. It
seems the time has come to remove it, since it's
not only always disabled but there also don't seem
to be any applications that actually request a max
network latency.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Xose Vazquez Perez [Sat, 14 Apr 2012 21:33:21 +0000 (23:33 +0200)]
wireless: rt2x00: rt2800pci add more RT539x ids
RT539x devices:
(0x1814, 0x5362)
(0x1814, 0x5392)
Taken from ralink driver 2011_0406_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Xose Vazquez Perez [Sat, 14 Apr 2012 21:00:01 +0000 (23:00 +0200)]
wireless: rt2x00: rt{2500,73}usb.c put back duplicate id
put back 0x050d,0x7050 to rt73usb, same usb_id for two chips:
K7SF5D7050A ver 2xxx is rt2500
K7SF5D7050B ver 3xxx is rt73
<http://en-us-support.belkin.com/app/answers/detail/a_id/297/kw/K7SF5D7050>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 20:01:59 +0000 (22:01 +0200)]
ath9k: simplify ath9k_hw_get_scaled_power function
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 20:01:58 +0000 (22:01 +0200)]
ath9k: introduce ath9k_hw_get_scaled_power helper
The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 20:01:57 +0000 (22:01 +0200)]
ath9k: use consistent value for REDUCE_SCALED_POWER_BY_THREE_CHAIN
The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.
In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.
54242509439325. Replace the the value
to 10 in these files.
Also add comments to eeprom_9287.c.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Sat, 14 Apr 2012 18:35:19 +0000 (20:35 +0200)]
ath9k: use ath9k_hw_update_regulatory_maxpower in ath9k_hw_def_set_txpower
We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Axel Lin [Sat, 14 Apr 2012 02:38:36 +0000 (10:38 +0800)]
net/wireless: use module_pci_driver
This patch converts the drivers in drivers/net/wireless/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jouni Malinen <j@w1.fi>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 13 Apr 2012 19:02:57 +0000 (12:02 -0700)]
mac80211: add function retrieve average rssi
Add utility function to provide the average rssi per vif
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 13 Apr 2012 18:57:43 +0000 (13:57 -0500)]
rtlwifi: rtl8192ce: Remove false positives for kmemleak
When rtl8192ce is in operation, kmemleak indicates a number of leaks, yet
when the driver is removed all are gone. These false positives happen
in two locations:
unreferenced object 0xffff880041124000 (size 9536):
comm "work_for_cpu", pid 9295, jiffies
4295037203 (age 20596.320s)
hex dump (first 32 bytes):
33 00 00 01 01 6d 00 00 00 00 b1 0e 21 0b 00 00 3....m......!...
01 01 6d 00 00 00 00 8b 20 c0 e9 00 00 01 01 6d ..m..... ......m
backtrace:
[<
ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
[<
ffffffff8138d01f>] kmalloc_large_node+0x9a/0xa6
[<
ffffffff811335a5>] __kmalloc_node_track_caller+0x175/0x3b0
[<
ffffffff812ddfe3>] __alloc_skb+0x73/0x230
[<
ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
[<
ffffffffa091a3b7>] rtl_pci_probe+0x10e0/0x17d2 [rtlwifi]
-- snip --
unreferenced object 0xffff8800b4d3f600 (size 256):
comm "kworker/u:2", pid 13221, jiffies
4297830173 (age 9424.568s)
hex dump (first 32 bytes):
1c d6 45 b1 00 88 ff ff 1c d6 45 b1 00 88 ff ff ..E.......E.....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
[<
ffffffff81130f43>] kmem_cache_alloc_node+0x153/0x270
[<
ffffffff812ddfb6>] __alloc_skb+0x46/0x230
[<
ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
[<
ffffffffa093264a>] rtl92c_set_fw_rsvdpagepkt+0x22a/0x5c0 [rtl8192c_common]
-- snip --
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yoshinori Sato [Fri, 13 Apr 2012 15:32:32 +0000 (00:32 +0900)]
ath5k: add PCI id
This device works fine of ath5k.
Details bellow
05:00.0 0200: 168c:ff1b (rev 01)
05:00.0 Ethernet controller: Atheros Communications Inc. Device ff1b (rev 01)
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at
febf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k
ath5k 0000:05:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ath5k 0000:05:00.0: setting latency timer to 64
ath5k 0000:05:00.0: registered as 'phy0'
ath: EEPROM regdomain: 0x67
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: 00
ath: Regpair used: 0x67
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:14:22 +0000 (16:44 +0530)]
ath9k: fix beacon descriptor
The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:14:21 +0000 (16:44 +0530)]
ath9k: skip beaconing when reset work is pending
Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:14:20 +0000 (16:44 +0530)]
ath9k: reset noiseimmunity level to default
After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 11:08:40 +0000 (16:38 +0530)]
cfg80211: increse bss expire time
The background scan completion takes more time when the station is
having heavy uplink traffic. The scan state machine decides to fall
back to home channel on every off-channel visit when there are pending
frames in tx queue. bgscan completion took ~30sec on dual band US
regulatory card.
scan period = (20 active channels * probe timeout) +
(12 passive channels * passive probe timeout) +
(32 * timeout on home channel) +
(32 * flush timeout)
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 07:46:34 +0000 (13:16 +0530)]
ath9k: fix ibss beacon next tbtt
Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 13 Apr 2012 07:46:33 +0000 (13:16 +0530)]
ath9k: fix ibss fair beacon distribution for AR9462
Update AR9462 initval to fix unbalance beacon distribution
in Ad-Hoc network.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Matt Renzelmann [Thu, 12 Apr 2012 22:42:43 +0000 (17:42 -0500)]
hostap: GFP_ATOMIC/GFP_KERNEL cleanup
The driver is allocating memory during initialization with GFP_ATOMIC
even though GFP_KERNEL is sufficient. This patch fixes it.
Signed-off-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 12 Apr 2012 21:32:23 +0000 (14:32 -0700)]
mac80211: Take into account TSF adjustment latency in Toffset setpoint
When testing mesh synchronization we observed a global TSF slowdown that
was dependent on the number of synchronized mesh stations. This seems
to be caused by the TSF adjustment (read/write) latency.
Adding a small margin to the Toffset setpoint solved the problem.
Signed-off-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 12 Apr 2012 21:32:22 +0000 (14:32 -0700)]
mac80211: Choose a new toffset setpoint if a big tsf jump is detected.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 12 Apr 2012 21:32:21 +0000 (14:32 -0700)]
mac80211_hwsim: fixup for tsf setting
Last patch I sent failed to take into account the offset of each phy.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 12 Apr 2012 21:32:20 +0000 (14:32 -0700)]
mac80211: Set the correct values for hwmp (1) and airtimeLinkMetric (1)
Per sections 8.4.2.100.2 and 8.4.2.100.3 of Std 802.11-2012
Reported-by: Shinichi Hotori <hotorinn@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 12 Apr 2012 20:35:58 +0000 (22:35 +0200)]
ath9k: optimize the hardware hang check
Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 12 Apr 2012 20:35:57 +0000 (22:35 +0200)]
ath9k: do not register LEDs on AR913x
LED support is typically handled via system GPIO on these platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 12 Apr 2012 20:35:56 +0000 (22:35 +0200)]
ath9k_hw: add support for 8 AP mode interfaces
Also tweak beacon response times for better stability with the shorter
timer intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jonathan Bither [Thu, 12 Apr 2012 19:44:47 +0000 (15:44 -0400)]
ath5k: use compare_ether_addr on MAC addresses instead of memcmp
Following Felix's recent patchset as an example I have replaced memcmp with
compare_ether_addr.
"Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp."
Signed-off-by: Jonathan Bither <jonbither@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Thu, 12 Apr 2012 17:04:00 +0000 (10:04 -0700)]
ath9k: Gather and report IRQ sync_cause errors.
Report all defined sync_cause errors in debugfs
to aid with debugging.
Use a macro to print out the interrupts file contents
to decrease code duplication.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Thu, 12 Apr 2012 17:03:59 +0000 (10:03 -0700)]
ath9k: Use macro to decrease code when priting recv stats.
This hides some repetitive code, and will help if the
column widths ever need to change.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Thu, 12 Apr 2012 13:09:49 +0000 (16:09 +0300)]
mac80211: check IEEE80211_HW_QUEUE_CONTROL in ieee80211_check_queues()
Commit
3a25a8c8 (mac80211: add improved HW queue control) introduced a
bug when running in AP mode without the IEEE80211_HW_QUEUE_CONTROL
flag set. The ieee80211_check_queues() function always returns
-EINVAL, preventing AP mode from starting. To fix this, check whether
this flag is set before checking if cab_queue is set properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 15 Mar 2012 09:16:16 +0000 (10:16 +0100)]
cfg80211: enforce lack of interface combinations
My grand plan to allow drivers to gradually move over
to advertising virtual interface combinations and only
enforce with drivers that do want it enforced doesn't
seem to be working out, only Christian ever added the
advertising (to carl9170), nobody else did.
Begin enforcing combinations in cfg80211 so that users
can rely on the information reported about a device.
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 16 Apr 2012 18:13:55 +0000 (14:13 -0400)]
Merge branch 'wireless-next' of git://git./linux/kernel/git/iwlwifi/iwlwifi
Arend van Spriel [Wed, 11 Apr 2012 09:52:50 +0000 (11:52 +0200)]
brcm80211: smac: only provide valid regulatory hint
The driver provides a regulatory hint to cfg80211 as obtained from the
SPROM. Mostly, this will be a two-letter ISO country code. However, it
may obtain special country code similar to the world regulatory domain
as used in cfg80211. This patch avoids setting these special codes as
the hint is lost to cfg80211.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Wed, 11 Apr 2012 09:52:49 +0000 (11:52 +0200)]
brcm80211: smac: do not use US as fallback regulatory hint
The brcmsmac driver provides the country code from sprom as a regulatory
hint to cfg80211. When brcmsmac does not find a country code entry in
the sprom it passes 'US' as regulatory hint. Better approach is to rely
on the world regulatory domain in cfg80211/crda.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 11 Apr 2012 09:52:48 +0000 (11:52 +0200)]
brcm80211: fmac: clean up chip id table
Remove unsupported chip ID and rearrange the list in alphabetical
order
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 11 Apr 2012 09:52:47 +0000 (11:52 +0200)]
brcm80211: fmac: postpone dongle RF enabling.
BRCMF_C_UP is the command that asks the firmware to enable RF of
dongle. Some firmware initialization steps must be performed during
RF is down. Postpone BRCMF_C_UP firing until brcmf_netdev_open get
called to ensure firmware have enough time to finish
initialization.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Wed, 11 Apr 2012 09:52:46 +0000 (11:52 +0200)]
brcm80211: fmac: add frame header extension support
A header extension is introduced in the received frame to provide
extra space for dongle information. This won't affect current
supported chipset since the data_offset is 0. But it's necessary for
adding support for future chipset.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Wed, 11 Apr 2012 09:52:45 +0000 (11:52 +0200)]
brcm80211: fmac: register primary net device with device mac address
The primary net device was registered with a primary mac address and
upon IFUP it was set to match the actual mac address from the device.
This patch changes that and moves the brcmf_add_if() call to the common
part of the driver.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Wed, 11 Apr 2012 09:52:44 +0000 (11:52 +0200)]
brcm80211: fmac: remove primary mac address handling from brcmf_net_attach
The mac address for the primary interface was handled different from
the other interfaces. The code has been restructured such that the
brcmf_net_attach function treats the interfaces equal.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Wed, 11 Apr 2012 09:52:43 +0000 (11:52 +0200)]
brcm80211: fmac: make brcmf_net_attach() static
The function brcmf_net_attach() is only used within dhd_linux.c so
it does not need to be extern. This patch makes the function static.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 11 Apr 2012 09:46:12 +0000 (15:16 +0530)]
mac80211: remove ieee80211_rx_bss_get
its not used where, while we directly obtain ieee80211_bss's
pointer in ibss.c by calling cfg80211_get_bss
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 11 Apr 2012 08:28:15 +0000 (13:58 +0530)]
ath9k_htc: Add Panasonic N5HBZ0000055 device id
Reported-by: Ryan Roper <ryan.roper@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michal Kazior [Wed, 11 Apr 2012 06:47:56 +0000 (08:47 +0200)]
mac80211: remove hw.conf.channel usage where possible
Removes hw.conf.channel usage from the following functions:
* ieee80211_mandatory_rates
* ieee80211_sta_get_rates
* ieee80211_frame_duration
* ieee80211_rts_duration
* ieee80211_ctstoself_duration
This is in preparation for multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 11 Apr 2012 04:04:08 +0000 (09:34 +0530)]
ath9k_hw: Remove BTCOEX initvals
The MAX_TXPWR table for BTCOEX is not needed for AR9462.
Programming these values to the HW results in undesirable
behavior - for example, large number of delimiter/data
underruns are seen in AES-CCMP mode. Also, registers like
AR_PCU_MISC_MODE2 return 0xdeadbeef after the BTCOEX_MAX
power table is programmed to the HW, and frames being transmitted
end up being looped back to the RX engine, an example being beacon
frames in IBSS mode.
Remove this table for now - this fixes CCMP performance and general
IBSS usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lorenzo Bianconi [Fri, 6 Apr 2012 18:48:15 +0000 (20:48 +0200)]
mac80211: fix an issue in ieee80211_tx_info count field management
I noticed a possible issue in the status count field management of the
ieee80211_tx_info data structure. In particular, when the AGGR
processing is employed,
status.rates[].count is set just for the first frame and not for
others belonging to the same burst, leading to wrong statistic data in
the mac80211 debug file system.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pontus Fuchs [Tue, 3 Apr 2012 14:39:58 +0000 (16:39 +0200)]
cfg80211: Add channel information to NL80211_CMD_GET_INTERFACE
If the current channel is known, add frequency and channel type to
NL80211_CMD_GET_INTERFACE.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Tue, 3 Apr 2012 01:40:50 +0000 (03:40 +0200)]
rt2800: zero registers of unused TX rings
This is needed if we take over after drivers which use those.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Tue, 3 Apr 2012 01:40:49 +0000 (03:40 +0200)]
rt2800: initialize queues before giving up due to DMA error
Don't immediately abort .start if DMA is busy before we
initialize the queues. Some drivers do not deinitialize
queues properly and we would fail to take over after them.
This behaviour is consistent with legacy driver.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Tue, 3 Apr 2012 01:40:48 +0000 (03:40 +0200)]
rt2800: add disabling of DMA before loading firmware
Legacy driver disables DMA before loading firmware.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jakub Kicinski [Tue, 3 Apr 2012 01:40:47 +0000 (03:40 +0200)]
rt2800: introduce wpdma_disable function
Introduce wpdma_disable function to simplify the code.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 28 Mar 2012 14:01:20 +0000 (16:01 +0200)]
mac80211: protect ->scanning by mutex in ieee80211_work_work()
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 28 Mar 2012 14:01:19 +0000 (16:01 +0200)]
mac80211: do not scan and monitor connection in parallel
Before we send probes in connection monitoring we check if scan is not
pending. But we do that check without locking. Fix that and also do not
start scan if connection monitoring is in progress.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Fri, 13 Apr 2012 18:28:56 +0000 (14:28 -0400)]
Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx
Wey-Yi Guy [Fri, 9 Mar 2012 17:22:53 +0000 (09:22 -0800)]
iwlwifi: change the default P2P support to "Yes"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Fri, 9 Mar 2012 15:15:04 +0000 (07:15 -0800)]
iwlwifi: more generic name for bluetooth command
Instead of hardcode 6000 and 2000, use more generic name
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 23:25:22 +0000 (16:25 -0700)]
iwlwifi: move scan related declarations out of iwl-core.h
Move these as part of iwl-core.h cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 23:16:19 +0000 (16:16 -0700)]
iwlwifi: move utility functions out of iwl-core.h
Move these functions to iwl-agn.h as part of
iwl-core.h cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 22:59:15 +0000 (15:59 -0700)]
iwlwifi: move iwl_bcast_addr to iwl-agn-sta.c
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 22:55:13 +0000 (15:55 -0700)]
iwlwifi: move iwl_force_rf_reset to iwl-agn-rx.c
Move this function as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 22:49:37 +0000 (15:49 -0700)]
iwlwifi: move iwl_send_statistics_request to iwl-agn.c
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 22:15:33 +0000 (15:15 -0700)]
iwlwifi: move iwl_print_rx_config_cmd to iwl-agn-rxon.c
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 01:23:51 +0000 (18:23 -0700)]
iwlwifi: move iwl_send_bt_config and mark it static
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 01:10:19 +0000 (18:10 -0700)]
iwlwifi: move iwl_set_tx_power and make it static
This function is used only in iwl-agn-rxon.c,
move it there and mark it static.
Move this function as part of iwl-core.c
cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 01:00:15 +0000 (18:00 -0700)]
iwlwifi: move iwlagn_fw_error to iwl-agn.c
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 00:47:23 +0000 (17:47 -0700)]
iwlwifi: move iwl_chswitch_done to iwl-mac80211.c
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 00:16:07 +0000 (17:16 -0700)]
iwlwifi: move iwl_set_rate to iwl-agn-rxon.c
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 14 Mar 2012 00:07:48 +0000 (17:07 -0700)]
iwlwifi: move iwl_connection_init_rx_config to iwl-agn-rxon.c
Move this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Tue, 13 Mar 2012 23:45:00 +0000 (16:45 -0700)]
iwlwifi: move iwl_set_flags_for_band to iwl-agn-rxon.c
Moving this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Tue, 13 Mar 2012 23:31:34 +0000 (16:31 -0700)]
iwlwifi: move iwl_set_rxon_channel to iwl-agn-rxon.c
Moving this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Tue, 13 Mar 2012 23:25:38 +0000 (16:25 -0700)]
iwlwifi: move iwl_set_rxon_ht to iwl-agn-rxon.c
Moving this as part of iwl-core.c cleanup.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Tue, 13 Mar 2012 23:15:09 +0000 (16:15 -0700)]
iwlwifi: move iwl_is_ht40_tx_allowed out of iwl-core.c
This is really something determined by
station parameters, so move it to
iwl-agn-sta.c.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Tue, 13 Mar 2012 22:33:18 +0000 (15:33 -0700)]
iwlwifi: move iwl_set_hw_rfkill_state and mark it static
iwl_set_hw_rfkill_state is used only in
iwl-agn.c. Move it there and mark it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Tue, 13 Mar 2012 22:24:44 +0000 (15:24 -0700)]
iwlwifi: move iwl_free_skb and mark it static
iwl_free_skb is used only in iwl-agn.c, move
it there and mark it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Tue, 13 Mar 2012 22:18:07 +0000 (15:18 -0700)]
iwlwifi: move channel switch related functions
With the creation of iwl-agn-devices.c,
iwl-core.c can be cleaned up a bit more by
moving beacon time related functions from
iwl-core.c to iwl-agn-devices.c
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Thu, 8 Mar 2012 08:18:04 +0000 (09:18 +0100)]
iwlwifi: calculate active legacy rates per station
Not all stations are guaranteed to have the same
active (available) legacy rates, so calculate them
on rate control init instead of hard-coding them
based on our own available rates. I have no idea
why that was done here before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Thu, 8 Mar 2012 09:19:55 +0000 (10:19 +0100)]
iwlwifi: make iwl_sta_fill_lq static
It's only used in a single place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Meenakshi Venkataraman [Wed, 7 Mar 2012 21:54:08 +0000 (13:54 -0800)]
iwlwifi: move iwlagn_hw_valid_rtc_data_addr prototype
Since this function is now used only by
op_mode, remove it from iwl-shared.h and move
it to iwl-agn.h.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Thu, 12 Apr 2012 21:07:13 +0000 (14:07 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into wireless-next
Johannes Berg [Tue, 10 Apr 2012 21:10:28 +0000 (14:10 -0700)]
iwlwifi: dynamically determine lib_ops
Having the pointer to lib_ops in the config
makes it impossible to split the driver into
different modules. Determine the ops based on
the device family enumeration to get rid of
the direct pointer.
Also move all the opmode specific code from
the iwl-[1256]000.c files into a new file
iwl-agn-devices.c so that the former only
have configuration data now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislav Yakovlev [Wed, 11 Apr 2012 01:44:47 +0000 (21:44 -0400)]
net/wireless: ipw2x00: add supported cipher suites to wiphy initialization
Driver doesn't report its supported cipher suites through cfg80211
interface. It still uses wext interface and probably will not work
through nl80211, but will at least correctly advertise supported
features.
Bug was reported by Omar Siam.
https://bugzilla.kernel.org/show_bug.cgi?id=43049
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jim Cromie [Wed, 11 Apr 2012 00:56:34 +0000 (18:56 -0600)]
prism54: replace open-coded ARRAY_SIZE with macro
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jim Cromie [Tue, 10 Apr 2012 23:02:34 +0000 (17:02 -0600)]
brcm80211: replace open-coded ARRAY_SIZE with the macro
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:20 +0000 (19:43 +0200)]
NFC: Fix LLCP link timeout typo
We were sending the LTO TLV as a version TLV instead of the actual link
timeout one.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:19 +0000 (19:43 +0200)]
NFC: Add MIUX to the local LLCP general bytes
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:18 +0000 (19:43 +0200)]
NFC: pn533 Rx chaining support
When buffers on the receiption path exceed 262 bytes, the pn533 uses
a chaining mechanism where the initiator has to send NULL data frames
to fetch the remaining frames.
We do that from a workqueue context while holding the cmd lock. Once the
MI bit is gone, we aggregate the queued received skbs.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:17 +0000 (19:43 +0200)]
NFC: Convert pn533 from tasklet to workqueues
There is no need for soft IRQ contexts, and workqueues are more flexible.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:16 +0000 (19:43 +0200)]
NFC: Call llcp_add_header properly when sending LLCP DM or DISC
dsap and ssap were swapped when sending DN or DISC.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:15 +0000 (19:43 +0200)]
NFC: Fix LLCP TLV building routine
The if logic could lead to zero length TLVs.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:14 +0000 (19:43 +0200)]
NFC: No need to apply twice the modulo op to LLCP's recv_n
recv_n is set properly when receiving an HDLC frame.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Tue, 10 Apr 2012 17:43:13 +0000 (19:43 +0200)]
NFC: Dump LLCP frames
At KERN_DEBUG level.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This page took 0.043931 seconds and 5 git commands to generate.