Valentine Barshak [Sun, 30 Dec 2007 23:28:50 +0000 (15:28 -0800)]
USB: add ehci-ppc-of bus glue (device-tree aware)
This adds device-tree-aware ehci-ppc-of driver.
The code is based on the ehci-ppc-soc driver by
Stefan Roese <sr@denx.de>.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dmitry Baryshkov [Sun, 30 Dec 2007 19:56:27 +0000 (11:56 -0800)]
USB: pxa2xx_udc: use debugfs not procfs
Use debugfs instead of /proc/driver/udc
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sat, 5 Jan 2008 21:21:43 +0000 (13:21 -0800)]
USB: at91_udc uses generic GPIO calls; minor cleanup
Various small at91_udc cleanups:
- Use generic GPIO calls, not older platform-specific ones
- Use gpio_request()/gpio_free()
- Use VERBOSE_DEBUG convention, not older VERBOSE
- Fix sparse complaint about parameter type (changed to gfp_t)
- Add missing newline to some rarely-seen debug messages
- Fix some old cleanup bugs on probe() fault paths
Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 27 Dec 2007 19:19:49 +0000 (11:19 -0800)]
USB: ohci-at91 uses generic GPIO calls
Update the ohci-at91 bus glue to start understanding about the per-port
power switch GPIOs it's given (on the sam9263-ek and potentially other
boards). For the moment this just claims them and forces them active
(assuming active-low power enables) whenever the HCD is loaded.
The assumption is still that board setup configures the GPIOs. Using
gpio_request() tracks actual usage and guards against conflict.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Thu, 17 Jan 2008 18:24:38 +0000 (10:24 -0800)]
USB: Add documentation for USB suspend statistics.
This documents two newly created files:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
Documentation was placed in Documentation/ABI/testing, since that's where the
documentation is for the other USB sysfs power files.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Sat, 22 Dec 2007 00:54:15 +0000 (16:54 -0800)]
USB: Export suspend statistics
This patch exports two statistics to userspace:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
connected_duration is the total time (in msec) that the device has
been connected. active_duration is the total time the device has not
been suspended. With these two statistics, tools like PowerTOP can
calculate the percentage time that a device is active, i.e. not
suspended or auto-suspended.
Users can also use the active_duration to check if a device is actually
autosuspended. Currently, they can set power/level to auto and
power/autosuspend to a positive timeout, but there's no way to know from
userspace if a device was actually autosuspended without looking at the
dmesg output. These statistics will be useful in creating an automated
userspace script to test autosuspend for USB devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kevin Lloyd [Thu, 10 Jan 2008 19:11:04 +0000 (11:11 -0800)]
USB: sierra driver - add update dtr logic
The following improvements were made:
- Fixed control line issue where asserting DTR on ep5 would close ep2
- Added support for calc_num_ports (will help support future composite
devices)
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Harald Welte [Tue, 1 Jan 2008 14:08:35 +0000 (15:08 +0100)]
USB: ftdi_sio: Support for more JTAG adaptors
[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors
There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.
I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.
I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Thu, 3 Jan 2008 16:57:33 +0000 (16:57 +0000)]
USB: io_ti: clean up termios handling
Don't pass NULL into termios functions when calling them internally
Remove all the crap which then checks for NULL which can't occur now
Clear CMSPAR as it is not supported
Report the baud rate back to the caller properly (See FIXME someone with
the docs)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Thu, 3 Jan 2008 17:03:11 +0000 (17:03 +0000)]
USB: ti_usb: termios cleanups
Remove internal NULL passing in termios code
Remove all the if checks it causes
Encode the baud rate back properly
Clear CMSPAR as it is not supported
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Thu, 3 Jan 2008 17:01:18 +0000 (17:01 +0000)]
USB: mos7720: clean up termios
Remove lots of NULL checks that can no longer occur
Encode the baud rate back into the termios (again someone with docs see
FIXME to improve this further)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dmitry Baryshkov [Fri, 21 Dec 2007 09:18:01 +0000 (12:18 +0300)]
USB: tosa_udc_use_gpio_vbus.patch
Use gpio_vbus instead of udc_is_connected for udc on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 21 Dec 2007 08:29:05 +0000 (00:29 -0800)]
USB: fix HCD Kconfig goofage
Add a missing dependency which goofs up the xconfig display.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 10 Dec 2007 06:53:09 +0000 (22:53 -0800)]
USB: gadget: at91_udc minor fix (there is no number six)
Fix a small glitch noted by Yannick Cote. There is no endpoint number
six, so if a (broken) host wrongly tried to change or read status of
that endpoint, the driver could access reserved register space.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Yannick Cote <yanick@yanos.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Thu, 20 Dec 2007 11:23:03 +0000 (12:23 +0100)]
USB: fix NULL pointer dereference on drivers/usb/serial/whiteheat.c
Am Sonntag, 16. Dezember 2007 05:23:47 schrieb Andrew Morton:
> On Sat, 15 Dec 2007 07:08:52 -0800 (PST) bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=9573
> > There's a null pointer dereference on drivers/usb/serial/whiteheat.c as
> > follows:
> >
> > (1) line 613: the test "if (port->tty)" implies that null is a legal value
> > for "port->tty" at that point
> >
> > (2) neither firm_open nor firm_purge initialize "port->tty"
drivers/usb/serial/usb-serial::serial_open() sets port->tty
The check for NULL is bogus. This patch removes the check.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 19 Dec 2007 19:27:51 +0000 (11:27 -0800)]
USB: gadget: ethernet error path potential oops fix
Fix potential (never-observed) oops on rare error path,
bugzilla #9594. Fix uses the same test as used earlier.
Also make the adjacent "else" block look like an "else" block
instead of hiding like a bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 19 Dec 2007 19:30:39 +0000 (11:30 -0800)]
USB: ehci potential oops fix on ARC/TDI cores
Kernel bugzilla entry #9569 reports a potential OOPS in some code
supporting the integrated root hub TT support used on ARC/TDI
derived cores. (This seems to have been a longstanding issue.)
This patch cleans up usage of urb->dev->tt to avoid that potential
oops and also fixes some overly long lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tzachi Perelstein [Sat, 1 Dec 2007 16:07:04 +0000 (11:07 -0500)]
USB: add Marvell Orion USB host support
Some glue bits for the on-chip USB host controller in the Marvell Orion
family of ARM SoCs, which is basically EHCI compatible.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcin Slusarz [Sun, 16 Dec 2007 02:25:13 +0000 (03:25 +0100)]
USB: ehci-hcd: fix sparse warning about shadowing 'status' symbol
fix warning:
drivers/usb/host/ehci-hcd.c:832:8: warning: symbol 'status' shadows an earlier one
drivers/usb/host/ehci-hcd.c:790:71: originally declared here
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcin Slusarz [Sun, 16 Dec 2007 02:23:20 +0000 (03:23 +0100)]
USB: usbdevfs_urb: __user annotation
fix warning:
drivers/usb/core/devio.c:1226:20: warning: incorrect type in assignment (different address spaces)
drivers/usb/core/devio.c:1226:20: expected void *usercontext
drivers/usb/core/devio.c:1226:20: got void [noderef] <asn:1>*
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcin Slusarz [Sun, 16 Dec 2007 02:21:29 +0000 (03:21 +0100)]
USB: usb/storage/initializers.c: fix signedness difference
fix warnings:
drivers/usb/storage/initializers.c:83:26: warning: incorrect type in argument 5 (different signedness)
drivers/usb/storage/initializers.c:83:26: expected unsigned int *act_len
drivers/usb/storage/initializers.c:83:26: got int *<noident>
drivers/usb/storage/initializers.c:89:26: warning: incorrect type in argument 5 (different signedness)
drivers/usb/storage/initializers.c:89:26: expected unsigned int *act_len
drivers/usb/storage/initializers.c:89:26: got int *<noident>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 17 Dec 2007 06:37:40 +0000 (22:37 -0800)]
USB: PS3: Fix EHCI ISO transfer bug
This adds a workaround for an issue reported with ISO transfers
on some EHCI controllers, most recently with VIA KT800 and PS3
EHCI silicon.
The issue is that the silicon doesn't necessarily seem to be done
using ISO DMA descriptors (itd, sitd) when it marks them inactive.
(One theory is that the ill-defined mechanism where hardware caches
periodic transfer descriptors isn't invalidating their state...)
With such silicon, quick re-use of those descriptors makes trouble.
Waiting until the next frame seems to be a sufficient workaround.
This patch ensures that the relevant descriptors aren't available
for immediate re-use. It does so by not recycling them until after
issuing the completion callback which would reuse them by enqueueing
an URB and thus (re)allocating ISO DMA descriptors.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Masashi Kimoto <Masashi_Kimoto@hq.scei.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Joe Perches [Mon, 17 Dec 2007 19:40:18 +0000 (11:40 -0800)]
USB: Spelling fixes
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dmitry Baryshkov [Fri, 7 Dec 2007 02:18:03 +0000 (18:18 -0800)]
USB: gadget: pxa2xx_udc supports inverted vbus
Some boards (like e.g. Tosa) invert the VBUS-detection signal:
it's low when a host is supplying VBUS, and high otherwise.
Allow specifying whether gpio_vbus value is inverted.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Morton [Fri, 14 Dec 2007 00:15:34 +0000 (16:15 -0800)]
USB: testing driver: don't free a locked mutex
Dopey thing to do and lockdep will (or should) warn.
Spotted by Daniel Walker.
Cc: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Cc: Daniel Walker <dwalker@mvista.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthias Kaehlcke [Fri, 14 Dec 2007 00:15:33 +0000 (16:15 -0800)]
USB: testing driver: convert dev->sem to mutex
USB testing driver: convert semaphore dev->sem to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nick Piggin [Fri, 14 Dec 2007 00:15:35 +0000 (16:15 -0800)]
USB: mon nopage
Convert USB mon driver from nopage to fault.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Fri, 14 Dec 2007 00:15:29 +0000 (16:15 -0800)]
USB: mct232: speed, new termios and compliance cleanups
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Fri, 14 Dec 2007 00:15:28 +0000 (16:15 -0800)]
USB: keyspan_pda: clean up speed handling
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Fri, 14 Dec 2007 00:15:26 +0000 (16:15 -0800)]
USB: belkin_sa: clean up for new style termios and speed handling, plus style
A tester with actual hardware would be useful
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Fri, 14 Dec 2007 22:09:30 +0000 (14:09 -0800)]
USB: pl2303: Add autosuspend support to pl2303 usb serial converter.
Signed-off-by: Sarah Sharp <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Fri, 14 Dec 2007 22:08:35 +0000 (14:08 -0800)]
USB: pl2303: Move pl2303 vendor specific init to probe function.
Without this fix, the pl2303 usb-serial adapter would not suspend properly
unless it had been opened first. A pl2303 type_1 chip will still break if the
system is hibernated while the RS-232 connector is powered by another system.
This was broken before, and a reset resume does not fix it. All other suspend
and autosuspend scenarios work with ATEN pl2303 adaptors with HX and type_1 chips.
Signed-off-by: Sarah Sharp <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Fri, 14 Dec 2007 22:08:00 +0000 (14:08 -0800)]
USB: pl2303: Cleanup FISH and SOUP macros in pl2303 driver.
Replace the FISH and SOUP macros that violated the macro guidelines in CodingStyle.
Turn them into function calls with clearer variable names.
Signed-off-by: Sarah Sharp <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 6 Dec 2007 16:10:39 +0000 (11:10 -0500)]
USB: dummy_hcd: change the default power budget
This patch (as1025) changes the default power budget for dummy-hcd to
500 mA and makes it a preprocessor parameter for easier testing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 11 Dec 2007 21:05:30 +0000 (16:05 -0500)]
USB: EHCI: add separate IAA watchdog timer
This patch (as1028) was mostly written by David Brownell; I made only
a few changes (extra log info and a small bug fix -- which might
account for why David's version had to be reverted). It adds a new
watchdog timer to the ehci-hcd driver to be used exclusively for
detecting lost or missing IAA notifications.
Previously a shared timer had been used, which may have led to some
problems as reported by Christian Hoffmann.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 4 Dec 2007 19:35:15 +0000 (14:35 -0500)]
USB: add usbfs stubs for suspend and resume
This patch (as1022b) adds stub methods for suspend and resume to the
usbfs driver. There isn't much they can do since there's no way to
inform a user task about the events. But it's important to have the
stubs, because an upcoming change to usbcore will automatically unbind
drivers that don't have those methods when a suspend occurs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthias Kaehlcke [Tue, 4 Dec 2007 15:15:40 +0000 (16:15 +0100)]
USB: Edgeport USB Serial Converter: convert es_sem to mutex
Edgeport USB Serial Converter: convert semaphore es_sem to the
mutex API
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 3 Dec 2007 20:44:29 +0000 (15:44 -0500)]
USB: updates to usb_reset_composite_device()
This patch (as1023) updates the code in usb_reset_composite_device():
Some local variable declarations are moved to inner loops.
The interface locks are not acquired. This isn't necessary
any more; its only reason was to prevent an interface from
being suspended or resumed during the reset. But now
interface power management is controlled by the USB device
lock, not by the interface lock.
The check for whether the interface is registered is removed.
There doesn't seem to be any reason for checking; a driver
for a non-registered interface deserves to be informed of
device resets just as much as any other.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 3 Dec 2007 20:42:10 +0000 (15:42 -0500)]
USB: repair USBDEVFS_CONNECT ioctl
For as long as I've known about it, the USBDEVFS_CONNECT ioctl hasn't
done what it's supposed to. The current code reprobes _all_ the
unbound USB interfaces; this patch (as1021) makes it reprobe only the
interface for which it was called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Benjamin Herrenschmidt [Thu, 6 Dec 2007 21:29:46 +0000 (13:29 -0800)]
usb: Remove OHCI useless masking/unmasking of WDH interrupt
The OHCI driver's IRQ handler, while processing a WDH interrupt, masks
and unmasks it. I believe this is both broken (the write may still be
posted during the donelist processing it's trying to safeguard) and
useless as this IRQ may not be reissued until it's acked (unless this
legacy code is an uncommented workaround for some chip erratum).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Jones [Tue, 11 Sep 2007 21:07:31 +0000 (14:07 -0700)]
USB: convert ehci debug files to use debugfs instead of sysfs
We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Jones [Tue, 11 Sep 2007 21:07:31 +0000 (14:07 -0700)]
USB: convert ohci debug files to use debugfs instead of sysfs
We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Tue, 27 Nov 2007 06:11:55 +0000 (22:11 -0800)]
USB: always announce a device has been added to the system
Distros (like SuSE) want to know this information, to make it easier
to handle support issues. Might as well let everyone benefit from this.
This is also enabled whenever CONFIG_USB_DEBUG is enabled, to help with
debugging.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 Nov 2007 21:28:55 +0000 (16:28 -0500)]
USB: dummy_hcd: don't register drivers on the platform bus
This patch (as1017) makes dummy_hcd behave more like the other USB
peripheral controller drivers by no longer registering its
gadget driver on the platform bus. Doing that has always been a
mistake, since a usb_gadget_driver isn't a platform_driver. Instead
the gadget driver is left unregistered in sysfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Balaji Rao [Wed, 21 Nov 2007 20:28:14 +0000 (01:58 +0530)]
USB: force handover port to companion when hub_port_connect_change fails
This patch hands over the port to the companion when the
hub_port_connect_change fails.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patrik Sevallius [Tue, 20 Nov 2007 17:32:00 +0000 (09:32 -0800)]
USB: usb peripheral controller driver oops avoidance
I'm having problem with oopses when rebooting, if I modprobe g_serial
and rmmod g_serial and do a reboot I get an oops in device_shutdown().
The reason seems to be that usb_gadget_unregister_driver() doesn't do
enough cleanup. With this at91_udc patch I don't get the oops.
Signed-off-by: Patrik Sevallius <patrik.sevallius@enea.com>
[ Same bug was in other peripheral controller drivers; fixed ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andre Haupt [Tue, 20 Nov 2007 10:41:37 +0000 (11:41 +0100)]
USB: cyberjack: remove a unnecessary variable.
This also fixes a sparse warning that symbol 'result' shadows an earlier one.
Signed-off-by: Andre Haupt <andre@bitwigglers.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Wed, 14 Nov 2007 01:10:09 +0000 (17:10 -0800)]
USB: Prepare serial core for autosuspend.
Claim the interface for a USB to serial converter when the tty is open,
and release the interface when the tty is closed.
If a driver doesn't provide a resume function, use the generic resume
instead.
Make sure the generic resume function does not submit the URBs if we're
coming back from autosuspend. On autoresume, we know that the open
function will be called next, which will attempt to submit the URBs. If
we submit them in the resume function, the open will fail.
This works for:
- autosuspend
- suspending with the tty open or closed
- hibernate with the tty closed
A hibernate (or a suspend that causes the USB subsystem to lose power)
has issues. If you have the tty open when you hibernate, a new tty will
be created when the device re-enumerates during resume.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 19 Nov 2007 20:58:36 +0000 (12:58 -0800)]
USB: gadget code switches to pr_err() and friends
We now have pr_err(), pr_warning(), and friends ... start using
them in the gadget stack instead of printk(KERN_ERR) and friends.
This gives us shorter lines and somewhat increased readability.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 19 Nov 2007 20:57:45 +0000 (15:57 -0500)]
USB: don't change HC power state for a FREEZE
This patch (as1016) prevents PCI-based host controllers from
undergoing a power-state change during a FREEZE or a PRETHAW. Such
changes are needed only during a SUSPEND.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 19 Nov 2007 15:15:02 +0000 (10:15 -0500)]
USB: make ksuspend_usbd thread non-freezable
This patch (as1012b) makes the ksuspend_usbd kernel thread
non-freezable. Since the PM core has been changed to lock all devices
during a system sleep, the thread no longer needs to be frozen. It
won't interfere with a system sleep because before trying to resume a
root hub device, it acquires the device's lock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Julia Lawall [Wed, 14 Nov 2007 08:15:16 +0000 (09:15 +0100)]
USB: Drop unnecessary continue in a few drivers
Continue is not needed at the bottom of a loop.
The semantic patch implementing this change is as follows:
@@
@@
for (...;...;...) {
...
if (...) {
...
- continue;
}
}
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert P. J. Day [Wed, 14 Nov 2007 21:21:00 +0000 (16:21 -0500)]
USB: linux/usb/Kbuild needs only "header-y", not "unifdef-y"
Given that none of the referenced header files test the proprocessor
conditional __KERNEL__, there's no point "unifdef"fing them.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Aristeu Rozanski [Tue, 13 Nov 2007 22:22:07 +0000 (17:22 -0500)]
USB: usb_serial_console: allocate fake tty and termios before calling driver open() method
The usb serial method set_termios() is called for the first time from
open() method in order to set up the termios structure with the default
device's settings, ignoring the current settings. Once it's initialized,
the next set_termios() calls will update the device with the
tty->termios settings.
Currently USB serial console code calls the driver open() method without
a tty and after that will allocate a fake tty and termios so the command
line arguments can be applied to the device
(console=ttyUSB0,115200,...). This makes the driver overwrite the
termios with the default settings and not applying the command line
options.
This patch changes usb_console_setup() to allocate the fake tty and
termios before the open() method is called.
Tested successfully with a pl2303
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Aristeu Rozanski [Mon, 12 Nov 2007 20:15:02 +0000 (15:15 -0500)]
USB: usb_serial: clean tty reference in the last close
When a usb serial adapter is used as console, the usb serial console
driver bumps the open_count on the port struct used but doesn't attach
a real tty to it (only a fake one temporaly). If this port is opened later
using the regular character device interface, the open method won't
initialize the port, which is the expected, and will receive a brand new
tty struct created by tty layer, which will be stored in port->tty.
When the last close is issued, open_count won't be 0 because of the
console usage and the port->tty will still contain the old tty value. This
is the last ttyUSB<n> close so the allocated tty will be freed by the
tty layer. The usb_serial and usb_serial_port are still in use by the
console, so port_free() won't be called (serial_close() ->
usb_serial_put() -> destroy_serial() -> port_free()), so the scheduled
work (port->work, usb_serial_port_work()) will still run. And
usb_serial_port_work() does:
(...)
tty = port->tty;
if (!tty)
return;
tty_wakeup(tty);
which causes (manually copied):
Faulting instruction address: 0x6b6b6b68
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT PowerMac
Modules linked in: binfmt_misc ipv6 nfs lockd nfs_acl sunrpc dm_snapshot dm_mirror dm_mod hfsplus uinput ams input_polldev genrtc cpufreq_powersave i2c_powermac therm_adt746x snd_aoa_codec_tas snd_aoa_fabric_layout snd_aoa joydev snd_aoa_i2sbus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc pmac_zilog serial_core evdev ide_cd cdrom snd appletouch soundcore snd_aoa_soundbus bcm43xx firmware_class usbhid ieee80211softmac ff_memless firewire_ohci firewire_core ieee80211 ieee80211_crypt crc_itu_t sungem sungem_phy uninorth_agp agpart ssb
NIP:
6b6b6b68 LR:
c01b2108 CTR:
6b6b6b6b
REGS:
c106de80 TRAP: 0400 Not tainted (2.6.24-rc2)
MSR:
40009032 <EE,ME,IR,DR> CR:
82004024 XER:
00000000
TASK =
c106b4c0[5] 'events/0' THREAD:
c106c000
GPR00:
6b6b6b6b c106df30 c106b4c0 c2d613a0 00009032 00000001 00001a00 00000001
GPR08:
00000008 00000000 00000000 c106c000 42004028 00000000 016ffbe0 0171a724
GPR16:
016ffcf4 00240e24 00240e70 016fee68 016ff9a4 c03046c4 c0327f50 c03046fc
GPR24:
c106b6b9 c106b4c0 c101d610 c106c000 c02160fc c1eac1dc c2d613ac c2d613a0
NIP [
6b6b6b68] 0x6b6b6b68
LR [
c01b2108] tty_wakeup+0x6c/0x9c
Call Trace:
[
c106df30] [
c01b20e8] tty_wakeup+0x4c/0x9c (unreliable)
[
c106df40] [
c0216138] usb_serial_port_work+0x3c/0x78
[
c106df50] [
c00432e8] run_workqueue+0xc4/0x15c
[
c106df90] [
c0043798] worker_thread+0xa0/0x124
[
c106dfd0] [
c0048224] kthread+0x48/0x84
[
c106dff0] [
c00129bc] kernel_thread+0x44/0x60
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Slab corruption: size-2048 start=
c2d613a0, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<
c01b16d8>](release_one_tty+0xbc/0xf4)
050: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=
c2d60b88, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<
c00f30ec>](show_stat+0x410/0x428)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
This patch avoids this, clearing port->tty considering if the port is
used as serial console or not
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Aristeu Rozanski [Mon, 12 Nov 2007 20:14:49 +0000 (15:14 -0500)]
USB: usb_serial_console: fix command line parsing
Currently usb serial console support ignores the device and always use
ttyUSB0.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Bock [Sun, 11 Nov 2007 23:42:16 +0000 (00:42 +0100)]
USB: cypress_cy7c63: updated contact/usage information
here's a minor update to the cypress_cy7c63 driver
providing new contact and usage information.
From: Oliver Bock <bock@tfh-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Craig W. Nadler [Sun, 11 Nov 2007 23:00:15 +0000 (15:00 -0800)]
USB: add Printer Gadget Driver
G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 8 Nov 2007 20:15:28 +0000 (15:15 -0500)]
USB: usb-storage: new "lockable" subclass 0x07
This patch (as1011) adds a #define for the newly-created Lockable
(i.e., password-protected) subclass 0x07 for USB mass-storage devices.
The private ISD200 entry (which had been mapped to subclass 0x07) is
moved to 0xf0, which is unlikely to conflict with any official
subclass designation.
The US_SC_MIN and US_SC_MAX constants aren't used anywhere, so the
patch removes them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Joe Perches [Tue, 20 Nov 2007 01:53:33 +0000 (17:53 -0800)]
USB: Add missing "space" to printk messages
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Yoshihiro Shimoda [Thu, 22 Nov 2007 12:00:30 +0000 (21:00 +0900)]
USB: m66592-udc: Add support for SH7722 USBF
Add support for SuperH SH7722 USB Function.
M66592 is similar to SH7722 USBF. It can support SH7722 USBF by
changing several M66592 code.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthias Kaehlcke [Wed, 21 Nov 2007 23:13:16 +0000 (15:13 -0800)]
USB: TI 3410/5052 USB Serial: convert td_open_close_lock to mutex
TI 3410/5052 USB Serial: convert semaphore td_open_close_lock to the mutex
API.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kyungmin Park [Wed, 21 Nov 2007 23:13:15 +0000 (15:13 -0800)]
USB: device DMA support on OMAP2
The current omap udc dosen't support the DMA mode and it has some problem
at setup time on OMAP2 with previous patch file. I found that the code
assumes bulk out required the big data transfer. But MODE SELECT(6) sent
the only 24 bytes. it makes a problem. So I implement the small packets
handling for it.
It is tested with both linux and windows.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk [Wed, 21 Nov 2007 23:13:15 +0000 (15:13 -0800)]
USB: usb/mon/mon_bin.c: cleanups
- make the needlessly global struct mon_fops_binary static
- #if 0 the unused mon_bin_mmap() and related code
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jeff Garzik [Wed, 21 Nov 2007 23:13:10 +0000 (15:13 -0800)]
USB: s3c2410_udc: minor irq handler cleanups
- 'irq' argument is merely used in place of a constant; replace its usage
with that constant.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fernando Luis Vázquez Cao [Mon, 5 Nov 2007 07:21:11 +0000 (16:21 +0900)]
USB: sisusb: *_ioctl32_conversion functions do not exist in recent kernels
Remove dead code while at it.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fernando Luis Vazquez Cao [Wed, 21 Nov 2007 23:13:12 +0000 (15:13 -0800)]
USB: sis FB driver: *_ioctl32_conversion functions do not exist in recent kernels
Remove dead code while at it.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg KH <greg@kroah.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alain Degreffe [Fri, 26 Oct 2007 11:51:49 +0000 (13:51 +0200)]
USB: add iuu_phoenix driver
Signed-off-by: Alain Degreffe <eczema@ecze.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bartlomiej Zolnierkiewicz [Sat, 27 Oct 2007 16:01:04 +0000 (18:01 +0200)]
USB: isd200: don't include <linux/ide.h>
Now that commit
3794ade5b286cbd4551009dd341dbe9aeead2bc3 removed
incorrect dependency on CONFIG_IDE we can fix the driver to not
include <linux/ide.h>:
* add ATA_REG_{ERROR,LCYL,HCYL,STATUS}_OFFSET defines and use them
instead of IDE_{ERROR,LCYL,HCYL,STATUS}_OFFSET from <linux/ide.h>
* remove no longer needed <linux/ide.h> include
* remove incorrect comment added by the last commit:
- isd200.c is not the only user of struct hd_driveid besides IDE
(see drivers/block/xsysace.c and arch/um/drivers/ubd_kern.c)
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 12 Oct 2007 15:24:28 +0000 (17:24 +0200)]
USB: autosuspend for cdc-acm
Here we go. This patch implements suspend/resume and autosuspend
for the CDC ACM driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Wed, 24 Oct 2007 01:57:25 +0000 (18:57 -0700)]
USB: Remove unnecessary zeroing from ub
These zeroings were taken from usb-storage long time ago. I examined
the submission paths and usb_fill_bulk_urb and found them unnecessary.
Signed-off-by: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Jones [Tue, 11 Sep 2007 21:07:31 +0000 (14:07 -0700)]
USB: Convert from class_device to device for USB core
Convert from class_device to device for drivers/usb/core.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Mon, 28 Jan 2008 17:50:12 +0000 (09:50 -0800)]
USB: handle idVendor of 0x0000
Some crazy devices in the wild have a vendor id of 0x0000. If we try to
add a module alias with this id, we just can't do it due to a check in
the file2alias.c file. Change the test to verify that both the vendor
and product ids are 0x0000 to show a real "blank" module alias.
Note, the module-init-tools package also needs to be changed to properly
generate the depmod tables.
Cc: Janusz <janumix@poczta.fm>
Cc: stable <stable@kernel.org>
Cc: Jon Masters <jcm@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Andersson [Tue, 8 Jan 2008 15:39:49 +0000 (16:39 +0100)]
usb: fix usbtest halt check on big endian systems
usbtest did not swap the received status information when checking for
a non-zero value and failed to discover halted endpoints on big endian
systems.
Cc: stable <stable@kernel.org>
Signed-off-by: Jan Andersson <jan@gaisler.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Grant Grundler [Thu, 24 Jan 2008 05:31:03 +0000 (21:31 -0800)]
USB: storage: Add unusual_dev for HP r707
Add "FIX_CAPACITY" entry for HP Photosmart r707 Camera in "Disk" mode.
Camera will wedge when /lib/udev/vol_id attempts to access the last sector,
EIO gets reported to dmesg, and block device is marked "offline" (it is).
Reproduced vol_id behavior with:
"dd if=/dev/sda of=/dev/null skip=60800 count=1"
Cc: stable <stable@kernel.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nate Carlson [Thu, 24 Jan 2008 18:45:07 +0000 (12:45 -0600)]
USB: Variant of the Dell Wireless 5520 driver
I've got a Dell wireless 5520 card with a different USB ID - specifically, 8136
instead of 8137. Attached a small patch to add support, and the output of an
'ati3'.
If we could get this in, that'd be sweet. ;) Thanks!
nc@knight:~/tmp/linux-2.6.24-rc8/drivers/usb/serial$ lsusb | grep 8136
Bus 001 Device 005: ID 413c:8136 Dell Computer Corp.
nc@knight:~/tmp/linux-source-2.6.23/drivers/usb/serial$ cu -l ttyUSB0 -s 115200
Connected.
ati3
Manufacturer: Novatel Wireless Incorporated
Model: Expedite EU860D MiniCard
Revision: 10.10.04.01-01 [2007-04-11 14:07:19]
IMEI:
011186000228043
+GCAP: +CGSM,+DS,+ES
From: Nate Carlson <natecars@natecarlson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Thu, 10 Jan 2008 09:31:48 +0000 (10:31 +0100)]
USB: use GFP_NOIO in reset path
this function will run in the context of the scsi error handler thread.
It must use GFP_NOIO instead of GFP_KERNEL to avoid a possible
deadlock.
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ed Beroset [Thu, 17 Jan 2008 22:37:46 +0000 (17:37 -0500)]
USB: ftdi driver - add support for optical probe device
Added support for the Elster Unicom III Optical Probe.
The device ID has already been added to the usb.ids file.
Cc: stable <stable@kernel.org>
Signed-off-by: Ed Beroset <beroset@mindspring.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Akira Tsukamoto [Fri, 18 Jan 2008 09:58:28 +0000 (18:58 +0900)]
USB: pl2303: add support for RATOC REX-USB60F
pl2303: add support for RATOC REX-USB60F
This patch adds support for RATOC REX-USB60F Serial Adapters,
which is widely used in Japan recently.
Cc: stable <stable@kernel.org>
Signed-off-by: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Kozák [Sat, 12 Jan 2008 10:53:09 +0000 (11:53 +0100)]
USB: remove duplicate entry in Option driver and Pl2303 driver for Huawei modem
Remove entry for Huawei E620 UMTS/HSDPA card (ID: 12d1:1001) in pl2303 driver
Option driver is use instead
Cc: stable <stable@kernel.org>
Signed-off-by: Daniel Kozák <kozzi11@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bruno Redondi [Fri, 11 Jan 2008 21:00:59 +0000 (22:00 +0100)]
USB: sierra: add support for Onda H600/Zte MF330 datacard to USB Driver for Sierra Wireless
Added support for Onda H600/Zte MF330 GPRS/UMTS/HSDPA datacard
Cc: stable <stable@kernel.org>
Signed-off-by: Bruno Redondi <bruno.redondi@altarisoluzione.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Franco Lanza [Wed, 26 Dec 2007 02:29:33 +0000 (03:29 +0100)]
USB: ftdi-sio: Patch to add vendor/device id for ATK_16IC CCD
little patches only to add vendor/device id of ATK_16IC CCD cam for
astronomy.
From: Franco Lanza <nextime@nexlab.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Stark [Tue, 25 Dec 2007 17:32:08 +0000 (18:32 +0100)]
USB: ftdi_sio - enabling multiple ELV devices, adding EM1010PC
I work with a group of people on a free home automation tool called
FHEM. Some of the users own more than one USB-serial device by ELV. The
ftdi_sio driver has most of the ELV devices disabled by default and
needs to be re-enabled every time you get a new kernel. Additionally a
new device (EM 1010 PC - enegry monitor) is missing in the list.
Currently our users have to follow the instructions we provide at
http://www.koeniglich.de/fhem/linux.html ... However, to some users it
is too complicated to compile their own kernel module.
We are aware that you can specify one additional device using the
vendor/product option of the module. But lot's of users own more than
one device.
Cc: stable <stable@kernel.org>
Signed-off-by: Peter Stark <peter.stark@t-online.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Manish Katiyar [Sat, 15 Dec 2007 05:31:14 +0000 (11:01 +0530)]
USB : correct comments in usb/core/notify.c
This patch corrects the wrong function name mentioned in the comments
of usb_unregister_notify function.
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kevin Lloyd [Thu, 10 Jan 2008 19:11:04 +0000 (11:11 -0800)]
USB: sierra driver - add devices
The following improvements were made:
- Added new product support: MC5725, AC 880 U, MP 3G (UMTS & CDMA)
Cc: stable <stable@kernel.org>
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Damien Stuart [Sun, 6 Jan 2008 18:51:39 +0000 (13:51 -0500)]
USB: Adding YC Cable USB Serial device to pl2303
This simply adds the "YC Cable" as a vendor and its pl2303-based
USB<->Serial adapter as a product. This particular adapter is sold by
Radio Shack. I've done limited testing on a few different systems with
no issues.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jessica L. Blank [Mon, 31 Dec 2007 02:11:35 +0000 (20:11 -0600)]
USB: Sierra - Add support for Aircard 881U
Adds the appropriate vendor and device IDs for the AirCard 881U to
sierra.c. (This device is often rebadged by AT&T as the USBConnect 881).
Cc: stable <stable@kernel.org>
Signed-off-by: Jessica L Blank <j@twu.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Piotr Roszatycki [Wed, 2 Jan 2008 10:16:57 +0000 (11:16 +0100)]
USB: add support for 4348:5523 WinChipHead USB->RS 232 adapter
add support for:
4348:5523 WinChipHead USB->RS 232 adapter with Prolifec PL 2303 chipset
[ mingo@elte.hu: merged it and nursed it upstream ]
Cc: stable <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Craig Shelley [Thu, 3 Jan 2008 12:45:59 +0000 (12:45 +0000)]
USB: CP2101 New Device IDs
Six new device IDs for CP2101 driver.
Cc: stable <stable@kernel.org>
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Thu, 3 Jan 2008 18:04:40 +0000 (10:04 -0800)]
usb gadget: fix fsl_usb2_udc potential OOPS
For fsl_usb2_udc driver, ep0 also has a descriptor. Current code is
misleading and contains a logical mistake. Here is the patch to fix it.
http://bugzilla.kernel.org/show_bug.cgi?id=9595
Cc: stable <stable@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Thu, 3 Jan 2008 16:59:04 +0000 (16:59 +0000)]
USB: keyspan: Fix oops
If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom. Fortunately all we need to do is process the URB
without trying to ram its contents down the throat of an ex-tty.
Cc: stable <stable@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Fri, 1 Feb 2008 10:48:45 +0000 (21:48 +1100)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: kill swap_io_context()
as-iosched: fix inconsistent ioc->lock context
ide-cd: fix leftover data BUG
block: make elevator lib checkpatch compliant
cfq-iosched: make checkpatch compliant
block: make core bits checkpatch compliant
block: new end request handling interface should take unsigned byte counts
unexport add_disk_randomness
block/sunvdc.c:print_version() must be __devinit
splice: always updated atime in direct splice
Jens Axboe [Fri, 1 Feb 2008 10:34:49 +0000 (11:34 +0100)]
block: kill swap_io_context()
It blindly copies everything in the io_context, including the lock.
That doesn't work so well for either lock ordering or lockdep.
There seems zero point in swapping io contexts on a request to request
merge, so the best point of action is to just remove it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Randy Dunlap [Fri, 1 Feb 2008 06:09:08 +0000 (22:09 -0800)]
docbook: rapidio: fix fatal filename error
Fix docbook fatal error (files were renamed):
docproc: linux-2.6.24-git9/arch/ppc/kernel/rio.c: No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steven Rostedt [Fri, 1 Feb 2008 05:13:58 +0000 (00:13 -0500)]
fix directory entry in arch-x86-Makefile
Doing a make randconfig I came across this error in the Makefile.
This patch makes a directory out of arch/x86/mach-default for
CONFIG_X86_RDC321X
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 1 Feb 2008 10:06:56 +0000 (21:06 +1100)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix inconsistent .section usage in lib/
[SPARC/SPARC64]: Fix usage of .section .sched.text in assembler code.
Linus Torvalds [Fri, 1 Feb 2008 10:06:29 +0000 (21:06 +1100)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (173 commits)
[NETNS]: Lookup in FIB semantic hashes taking into account the namespace.
[NETNS]: Add a namespace mark to fib_info.
[IPV4]: fib_sync_down rework.
[NETNS]: Process interface address manipulation routines in the namespace.
[IPV4]: Small style cleanup of the error path in rtm_to_ifaddr.
[IPV4]: Fix memory leak on error path during FIB initialization.
[NETFILTER]: Ipv6-related xt_hashlimit compilation fix.
[NET_SCHED]: Add flow classifier
[NET_SCHED]: sch_sfq: make internal queues visible as classes
[NET_SCHED]: sch_sfq: add support for external classifiers
[NET_SCHED]: Constify struct tcf_ext_map
[BLUETOOTH]: Fix bugs in previous conn add/del workqueue changes.
[TCP]: Unexport sysctl_tcp_tso_win_divisor
[IPV4]: Make struct ipv4_devconf static.
[TR] net/802/tr.c: sysctl_tr_rif_timeout static
[XFRM]: Fix statistics.
[XFRM]: Remove unused exports.
[PKT_SCHED] sch_teql.c: Duplicate IFF_BROADCAST in FMASK, remove 2nd.
[BNX2]: Fix ASYM PAUSE advertisement for remote PHY.
[IPV4] route cache: Introduce rt_genid for smooth cache invalidation
...
Olof Johansson [Thu, 31 Jan 2008 23:50:02 +0000 (17:50 -0600)]
pasemi: Fix thinko in dma_direct_ops setup
[POWERPC] pasemi: Fix thinko in dma_direct_ops setup
The first patch will just fall through and still set dma_data to a bad
value, make it return directly instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Ungerer [Fri, 1 Feb 2008 07:40:52 +0000 (17:40 +1000)]
m68knommu: remove dead timer int pending code
Remove all the dead timer interrupt checking functions for the ColdFire
CPU "timers" hardware that are not used after switching to GENERIC_TIME.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Ungerer [Fri, 1 Feb 2008 07:40:49 +0000 (17:40 +1000)]
m68knommu: remove empty timer offset function for 68360
Switching to GENERIC_TIME means we no longer need the empty timer offset
function for the 68360 CPU.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.04765 seconds and 5 git commands to generate.