Russell King [Sun, 25 Mar 2012 22:55:23 +0000 (23:55 +0100)]
Merge branch 'sa11x0-mtd' into sa11x0
Russell King [Sat, 14 Jan 2012 16:57:02 +0000 (16:57 +0000)]
ARM: sa11x0: remove unused DMA controller definitions
Remove the new unused DMA controller definitions from mach/SA-1100.h.
These are now private to the SA-11x0 DMA engine driver and contained
within the driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 13 Jan 2012 12:07:24 +0000 (12:07 +0000)]
ARM: sa11x0: remove old SoC private DMA driver
Now that all users are converted over to using the DMA engine API,
we can get rid of the old platform dependent DMA driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 25 Mar 2012 22:54:52 +0000 (23:54 +0100)]
Merge branch 'sa11x0-ir' into sa11x0
Russell King [Sun, 25 Mar 2012 22:54:16 +0000 (23:54 +0100)]
Merge branch 'sa1111' into sa11x0
Conflicts:
arch/arm/common/sa1111.c
arch/arm/mach-sa1100/neponset.c
Fixed:
arch/arm/mach-sa1100/assabet.c
for the neponset changes
Russell King [Thu, 26 Jan 2012 11:45:27 +0000 (11:45 +0000)]
USB: sa1111: add hcd .reset method
Add the .reset method to the HCD, and update the .start method
accordingly for this change.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 11:10:20 +0000 (11:10 +0000)]
USB: sa1111: add OHCI shutdown methods
Add OHCI shutdown methods to cleanly shutdown the OHCI controller on
system shutdowns and reboots. This avoids the controller continuing
to run should be soft-reboot the platform, potentially scribbling
over system memory.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 10:52:34 +0000 (10:52 +0000)]
USB: sa1111: reorganize ohci-sa1111.c
Combine usb_hcd_sa1111_probe() and ohci_hcd_sa1111_drv_probe(), doing
the same for the remove methods.
Move sa1111_start_hc and sa1111_stop_hc to be located next to these
the probe/release functions, as they're only called from them.
Get rid of the /*----*/ breaker lines.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 10:39:57 +0000 (10:39 +0000)]
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
Use dev_dbg() instead, it's more friendly.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 10:37:46 +0000 (10:37 +0000)]
USB: sa1111: sparse and checkpatch cleanups
Clean up the ohci-sa1111 driver formatting to be more compliant with
current standards, and add 'static' to various function definitions
to avoid sparse complaints about undeclared functions. Remove the
unnecessary local declaration of 'usb_disabled', which can be found
instead in linux/usb.h.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Jan 2012 10:37:36 +0000 (10:37 +0000)]
ARM: sa11x0: don't static map sa1111
The sa1111 support will ioremap() the device; there is no need for
platforms to setup a static mapping for this. Remove the static
mapping for this device from badge4, jornada720 and neponset.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Jan 2012 10:28:09 +0000 (10:28 +0000)]
ARM: sa1111: use dev_err() rather than printk()
Use dev_err() to report device specific errors rather than printk().
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Jan 2012 10:20:00 +0000 (10:20 +0000)]
ARM: sa1111: cleanup sub-device registration and unregistration
Move the releasing of resources out of the release function - this
allows a cleaner and more conventional arrangement of the registration
failure paths and a saner unregistration process for these devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Jan 2012 10:22:49 +0000 (10:22 +0000)]
ARM: sa1111: only setup DMA for DMA capable devices
It's pointless registering the PS/2 interfaces with the dmabounce code
when there's no DMA support for these in hardware, so only setup the
DMA masks for two subdevices which support DMA - the OHCI and SAC.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Jan 2012 09:31:31 +0000 (09:31 +0000)]
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
Use the bus notifier to register sa1111 devices with dmabounce, rather
than after the device has been registered, potentially racing with
driver binding.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 16 Jan 2012 11:37:03 +0000 (11:37 +0000)]
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
Move the USB interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 16 Jan 2012 11:32:09 +0000 (11:32 +0000)]
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
Move the PCMCIA interface register definitions into the driver, rather
than keeping them in a common place.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 16 Jan 2012 11:29:43 +0000 (11:29 +0000)]
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
Move the PS/2 interface register definitions into the driver, rather
than keeping them in a common location.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 16 Jan 2012 14:28:25 +0000 (14:28 +0000)]
ARM: sa1111: delete unused physical GPIO register definitions
Get rid of the unused GPIO register definitions - we access GPIO
registers through the base + offset method, and having the phys
address definitions is unnecessary duplication.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 13:34:21 +0000 (13:34 +0000)]
ARM: sa1111: provide a generic way to prevent devices from registering
Some platforms don't want certain devices to be registered, because,
eg, the interface is not wired. Provide a way for platforms to
prevent various devices from being registered via a devid bitmask in
the platform data.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 13 Jan 2012 11:50:03 +0000 (11:50 +0000)]
NET: sa11x0-ir: add DMA support for SIR transmit mode
As the DMA engine API allows DMA channels to be reconfigured on the
fly, we can now support switching the DMA channel configuration to
support SIR transmit DMA without needing to claim an additional
physical DMA channel - thereby using up half the DMA channels just
for one driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 13 Jan 2012 11:48:13 +0000 (11:48 +0000)]
NET: sa11x0-ir: convert sa11x0-ir driver to use DMA engine API
Convert the sa11x0 IrDA driver to use the sa11x0 DMA engine driver
rather than our own platform specific DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 7 Mar 2012 11:46:12 +0000 (11:46 +0000)]
Merge branch 'sa11x0-dma' into sa11x0-ir
Russell King [Mon, 9 Jan 2012 21:45:51 +0000 (21:45 +0000)]
ARM: sa11x0: add SA-11x0 DMA device
Add sa11x0 DMA platform device and resources to the list of
generic platform devices for SA11x0 machines.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 9 Jan 2012 21:44:07 +0000 (21:44 +0000)]
DMA: sa11x0: add SA-11x0 DMA driver
Add support for the SA-11x0 DMA driver, which replaces the private
API version in arch/arm/mach-sa1100/dma.c.
We model this as a set of virtual DMA channels, one for each request
signal, and assign the virtual DMA channel to a physical DMA channel
when there is work to be done. This allows DMA users to claim their
channels, and hold them while not in use, without affecting the
availability of the physical channels.
Another advantage over this approach, compared to the private version,
is that a channel can be reconfigured on the fly without having to
release and re-request it - which for the IrDA driver, allows us to
use DMA for SIR mode transmit without eating up three physical
channels. As IrDA is half-duplex, we actually only need one physical
channel, and this architecture allows us to achieve that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Jan 2012 13:56:28 +0000 (13:56 +0000)]
NET: sa11x0-ir: split si->dev for IrDA transmit and receive buffers
The sa11x0-ir device is not the device which is doing the DMA, the
DMA is being performed by a separate DMA engine. Split the struct
device associated with each DMA channel from the main struct device,
but for the time being initialize it from the main struct device.
This is another preparatory step to converting this driver to use the
DMA engine API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Jan 2012 13:51:10 +0000 (13:51 +0000)]
NET: sa11x0-ir: fix size of SIR transmit buffer
The SIR transmit buffer was being allocated as 4000 bytes. IrDA now
has constants for the buffer sizes, and defines the maximum wrapped
SIR packet to be 4269 bytes as indicated by IRDA_SIR_MAX_FRAME. Use
this definition to allocate the transmit buffer instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Jan 2012 12:45:00 +0000 (12:45 +0000)]
NET: sa11x0-ir: convert to use scatterlist DMA API
Convert the sa11x0 IrDA driver to use the scatterlist DMA API. This
is a preparatory patch for converting the driver to use the DMA engine
API, which requires a struct scatterlist for every transfer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 20:49:28 +0000 (20:49 +0000)]
NET: sa11x0-ir: get rid of si->hscr0
si->hscr0 is initialized to zero, and never changed. Get rid of this
redundant variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 17:48:02 +0000 (17:48 +0000)]
NET: sa11x0-ir: move sa1100_irda_txdma_irq
Move the FIR DMA transmit completion function along-side the other FIR
protocol functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 17:10:01 +0000 (17:10 +0000)]
NET: sa11x0-ir: move SIR and FIR interrupt support
Move the interrupt handlers to the SIR and FIR sections of the file.
This improves the localization of the protocol handlers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 16:26:15 +0000 (16:26 +0000)]
NET: sa11x0-ir: indirect handling of SIR and FIR interrupts
Use the same method for doing this as we do for the tx_start functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 16:16:39 +0000 (16:16 +0000)]
NET: sa11x0-ir: split SIR and FIR tx functions
Split the SIR and FIR transmit functions, as they behave differently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 16:30:44 +0000 (16:30 +0000)]
NET: sa11x0-ir: factor out speed checks
Whenever we complete a transmit, we always check for a speed change.
This check was open coded in several places. Provide a helper
function to do this instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 16:40:07 +0000 (16:40 +0000)]
NET: sa11x0-ir: move sa1100_irda_{startup,shutdown,suspend,resume}
Places these functions in better locations in the file, near where
they are used. This saves some tiresome paging up/down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 15:38:15 +0000 (15:38 +0000)]
NET: sa11x0-ir: fix leak of tx skb
Ensure that we unmap and free a pending transmit skb when the interface
is stopped. We rearrange the code a little bit to give all places a
similar layout when freeing the skb in both the completion and interface
stop paths - this gives some consistency to the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 12:53:22 +0000 (12:53 +0000)]
NET: sa11x0-ir: containerize DMA data
Both the transmit and receive DMA store identical data: the skb, dma
address, and the dma registers. Move this data into its own data
structure. The following replacements were used:
rxskb -> dma_rx.skb
rxbuf_dma -> dma_rx.dma
rxdma -> dma_rx.regs
txskb -> dma_tx.skb
txbuf_dma -> dma_tx.dma
txdma -> dma_tx.regs
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 12:02:17 +0000 (12:02 +0000)]
NET: sa11x0-ir: obtain interrupt number from platform resources
Convert the sa11x0-ir driver to obtain its interrupt number from the
platform device resources, rather than via the asm/irq.h include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 12:07:24 +0000 (12:07 +0000)]
NET: sa11x0-ir: set netdev's parent struct device
Add the missing SET_NETDEV_DEV() call to set the parent device
correctly for this network interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 13:55:23 +0000 (13:55 +0000)]
NET: sa11x0-ir: handle DMA mapping errors properly
Handle DMA mapping errors in the rx skb allocation and tx paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Jan 2012 12:04:05 +0000 (12:04 +0000)]
NET: sa11x0-ir: fix documentation bug
Spell the module parameter correctly in comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 25 Jan 2012 10:42:52 +0000 (10:42 +0000)]
ARM: sa1111: change devid to be a bitmask
Change the sa1111 device id to be a bitmask. This allows us to
specify the actual device, while allowing a single driver to bind
to both PS2 devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 13:28:35 +0000 (13:28 +0000)]
ARM: sa11x0: badge4: move board specific ohci initialization to badge4.c
Move the handling of the 5v supply into badge4.c, removing this board
specific detail from the sa1111 ohci driver.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 13:25:47 +0000 (13:25 +0000)]
ARM: sa1111: add platform enable/disable functions
Add platform hooks to be called when individual sa1111 devices are
enabled and disabled. This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 11:01:18 +0000 (11:01 +0000)]
ARM: sa1111: add shutdown hook to sa1111_driver structure
Add a shutdown hook to the sa1111_driver structure to allow drivers
to be notified of system reboots and shutdowns.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 21:25:20 +0000 (21:25 +0000)]
ARM: sa1111: implement support for sparse IRQs
Implement the necessary allocation/freeing functionality to support
sparse IRQs with the SA-1111 device. On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 16 Jan 2012 00:09:22 +0000 (00:09 +0000)]
ARM: sa1111: finish "allow cascaded IRQs to be used by platforms"
Commit
19851c58e680 (sa1111: allow cascaded IRQs to be used by platforms)
moved the IRQ definitions to the .c file, and added an irq_base member
to the private data structure.
The inerrupt demultiplexer uses irq_base, but the interrupt setup code
does not. Also, although the commit adds a private data structure to
pass this data, it isn't even referenced, resulting in irq_base being
zero.
We also copied the IRQ numbers from the device info array into the actual
devices, resulting in wrong interrupt numbers passed to the sub-devices.
The net effect of this is that we always overwrite IRQs 0-54, even if
they are allocated elsewhere in the system.
Add the code necessary to setup the private irq_base, and use it in the
IRQ setup code. Make the SA-1111 probe fail with -EINVAL if there is no
platform data provided.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 11:19:48 +0000 (11:19 +0000)]
ARM: sa1111: add .owner initializer to sa1111 driver structures
Add a .owner initializer to the sa1111 driver structures to allow
allow the modules to be associated with their driver structures.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 14 Jan 2012 16:09:22 +0000 (16:09 +0000)]
ARM: sa1111: add sa1111 core driver .owner initializer
Add an initializer for the struct device_driver .owner member.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 3 Feb 2012 19:05:13 +0000 (19:05 +0000)]
ARM: sa1111: fix PWM state on suspend
We should not write to the SA1111 registers after setting the SLEEP
bit. Moreover, the manual says that the PWM registers should be
disabled before we enter sleep. So, move the clearing of these
registers earlier in the suspend sequence.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 3 Feb 2012 19:03:31 +0000 (19:03 +0000)]
ARM: sa1111: fix memory request/grant setup on PM events
We weren't re-enabling the memory request/grant signals on resume,
causing DMA devices on the sa1111 to fail.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Jan 2012 11:23:33 +0000 (11:23 +0000)]
ARM: sa11x0: neponset: don't static map neponset registers
Now that we ioremap() the neponset register space, there's no need
to static map the neponset registers. Get rid of this static mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 29 Jan 2012 11:19:06 +0000 (11:19 +0000)]
ARM: sa11x0: neponset: move register definitions to neponset.c
Move the board specific neponset register definitions to the board
file, rather than mach/neponset.h. However, as the NCR_0 register
definitions are used by some drivers, leave these behind.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 26 Jan 2012 11:50:23 +0000 (11:50 +0000)]
ARM: sa11x0: assabet/neponest: create neponset device in assabet.c
The neponset board is a daughter board for the Assabet. Create the
neponset platform device in assabet.c, where we don't have to wrap
it with machine_is_assabet() stuff. We also create this device
dynamically rather than keeping it as a static device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 23:29:47 +0000 (23:29 +0000)]
ARM: sa11x0: neponset: suspend/resume in _noirq state
Suspend and resume in the _noirq state, so that we're saving the
state of the modem control signals as late as possible, and restoring
them as early as possible. There's nothing to do in thaw/poweroff
methods as we've already saved the necessary state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 23:17:37 +0000 (23:17 +0000)]
ARM: sa11x0: neponset: place smc91x and sa1111 resources in neponset device
Complete the neponset device resources by covering the children's
memory resources in the parent neponset device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 23:05:08 +0000 (23:05 +0000)]
ARM: sa11x0: neponset: get parent IRQ from neponset device resource
Obtain the parent IRQ from the neponset device resource rather than
hard-coding it into the code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 22:22:18 +0000 (22:22 +0000)]
ARM: sa11x0: neponset: implement support for sparse IRQs
Implement the necessary allocation/freeing functionality to support
sparse IRQs with the Neponset device. On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 22:36:47 +0000 (22:36 +0000)]
ARM: sa11x0: neponset: dynamically create neponset child devices
Use platform_device_register_full() to dynamically create the various
neponset child platform devices, and place them below the neponset
device itself to ensure proper PM ordering and device structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 22:10:02 +0000 (22:10 +0000)]
ARM: sa11x0: neponset: save and restore MDM_CTL_0
Save and restore the modem output control register across a suspend/
resume, as well as the NCR register. Place these in a locally
allocated data structure rather than needing a new static variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 23:33:28 +0000 (23:33 +0000)]
ARM: sa11x0: neponset: add driver .owner initializer
Ensure that the driver .owner field is properly initialized.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 22:13:00 +0000 (22:13 +0000)]
ARM: sa11x0: neponset: shuffle some code around
Move the IRQ handler along side the rest of the IRQ code, and rearrange
the include files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 16 Jan 2012 09:31:47 +0000 (09:31 +0000)]
ARM: sa11x0: neponset: provide function to manipulate NCR_0
Rather than having direct register accesses to NCR_0 scattered amongst
the code, provide a function instead. This contains the necessary
race protection for this platform, ensuring that updates to this
register are safe.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 16 Jan 2012 00:17:41 +0000 (00:17 +0000)]
ARM: sa11x0: neponset: fix interrupt setup
Since ARM was converted to genirq, the neponset IRQ implementation has
gradually broken as a result of various subtle changes being introduced
into genirq.
It used to be that simple IRQs did not need an IRQ chip. This is no
longer the case, and genirq barfs in irq_set_handler(). Fix this by
introducing a dummy no-op chip, and registering it along with the flow
handler.
Neponset IRQs really don't have any masking ability - all we have is a
status register to allow us to decode the source, and a three input OR
gate inside a CPLD.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 09:25:57 +0000 (09:25 +0000)]
ARM: sa11x0: assabet: ensure that GPIO27 is driven
GPIO27 is just connected to a CPLD input without any pull-ups or pull-
downs. If GPIO27 is left as an input, it will float around mid-supply,
which for CMOS inputs is the worst place for a pin to be. Ensure that
this pin is driven.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 24 Jan 2012 09:23:19 +0000 (09:23 +0000)]
ARM: sa11x0: assabet: avoid glitching GPIOs when setting outputs
Avoid glitching the GPIO signals during initialization, which can
have undesirable effects. Ensure that the desired pin state is set
before we change the GPIO pin direction to be an output.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 21 Jan 2012 21:17:06 +0000 (21:17 +0000)]
ARM: sa11x0: assabet: deassert QMUTE to codec while codec is unpowered
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Jan 2012 10:25:29 +0000 (10:25 +0000)]
ARM: sa11x0: convert to use DEFINE_RES_xxx macros
Convert StrongARM-11x0 platforms and core SoC code to use the
DEFINE_RES_xxx macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 3 Feb 2012 18:16:45 +0000 (18:16 +0000)]
ARM: sa11x0: fix section mismatch warnings
Neponset calls sa1110_mb_disable() from __devinit code, but
sa1110_mb_disable() is marked __init, and so causes a section
mismatch warning.
As sa1110_mb_enable() and sa1110_mb_disable() need to be callable
from suspend/resume paths as well, they must not be marked __init
or __devinit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 23 Jan 2012 18:39:21 +0000 (18:39 +0000)]
ARM: sa11x0: fix sleep entry
Sometimes, we get stuck while trying to enter sleep. This seems
to occur if we do not have udelay() in the instruction cache. Avoid
this by requesting a short delay prior to modifying the SDRAM timings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Jan 2012 10:59:21 +0000 (10:59 +0000)]
ARM: sa11x0: fix off-by-one resource sizes
Hackkit defined its flash memory resource to be 32M + 1 byte.
Jornada defined the Epson video controller resources to be one byte
larger than they should be, and mis-mapped the SA-1111 companion
chip one byte smaller than it should be.
Fix these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 14 Jan 2012 15:51:07 +0000 (15:51 +0000)]
MTD: sa11x0: remove definitions and code left for documentation purposes
/*
* This is here for documentation purposes only - until these people
* submit their machine types. It will be gone January 2005.
*/
It's now seven years after that date, so let's remove this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 19 Dec 2011 13:50:21 +0000 (13:50 +0000)]
MTD: sa11x0: Remove shutdown handler
Commit
c4a9f88daf ([MTD] [NOR] fix ctrl-alt-del can't reboot for
intel flash bug) interferes with this work-around, causing MTD to
issue this warning:
Flash device refused suspend due to active operation (state 0)
The commit makes our work-around in the map driver unnecessary, so
let's remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Thu, 9 Feb 2012 03:21:53 +0000 (19:21 -0800)]
Linux 3.3-rc3
Linus Torvalds [Thu, 9 Feb 2012 03:11:00 +0000 (19:11 -0800)]
Merge branch 'iommu/fixes' of git://git./linux/kernel/git/joro/iommu
One patch fixes an bug in the ARM/MSM IOMMU code which returned sucess
in the unmap function even when an error occured and the other patch
adds a workaround into the AMD IOMMU driver to better handle broken IVRS
ACPI tables (this patch fixes the case when a device is not listed in
the table but actually translated by the iommu).
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/msm: Fix error handling in msm_iommu_unmap()
iommu/amd: Work around broken IVRS tables
Linus Torvalds [Thu, 9 Feb 2012 03:09:25 +0000 (19:09 -0800)]
Merge branch '3.3-rc-fixes' of git://git./linux/kernel/git/nab/target-pending
This series contains pending target bug-fixes and cleanups for v3.3-rc3
that have been addressed the past weeks in lio-core.git.
Some of the highlights include:
- Fix handling for control CDBs with data greater than PAGE_SIZE (andy)
- Use IP_FREEBIND for iscsi-target to address network portal creation
issues with systemd (dax)
- Allow PERSISTENT RESERVE IN for non-reservation holder (marco)
- Fix iblock se_dev_attrib.unmap_granularity (marco)
- Fix unsupported WRITE_SAME sense payload handling (martin)
- Add workaround for zero-length control CDB handling (nab)
- Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT (nab)
- Fix target_submit_cmd() exception handling (nab)
- Return correct ASC for unimplemented VPD pages (roland)
- Don't zero pages used for data buffers (roland)
- Fix return code of core_tpg_.*_lun (sebastian)
* '3.3-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
target: Fix unsupported WRITE_SAME sense payload
iscsi: use IP_FREEBIND socket option
iblock: fix handling of large requests
target: handle empty string writes in sysfs
iscsi_target: in_aton needs linux/inet.h
target: Fix iblock se_dev_attrib.unmap_granularity
target: Fix target_submit_cmd() exception handling
target: Change target_submit_cmd() to return void
target: accept REQUEST_SENSE with 18bytes
target: Fail INQUIRY commands with EVPD==0 but PAGE CODE!=0
target: Return correct ASC for unimplemented VPD pages
iscsi-target: Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT
target: Allow control CDBs with data > 1 page
iscsi-target: Fix up a few assignments
iscsi-target: make one-bit bitfields unsigned
iscsi-target: Fix double list_add with iscsit_alloc_buffs reject
iscsi-target: Fix reject release handling in iscsit_free_cmd()
target: fix return code of core_tpg_.*_lun
target: use save/restore lock primitive in core_dec_lacl_count()
target: avoid multiple outputs in scsi_dump_inquiry()
...
Linus Torvalds [Thu, 9 Feb 2012 03:06:30 +0000 (19:06 -0800)]
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Some simple md-related fixes.
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md: two small fixes to handling interrupt resync.
Prevent DM RAID from loading bitmap twice.
Linus Torvalds [Thu, 9 Feb 2012 03:05:47 +0000 (19:05 -0800)]
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
SPI bug fixes for v3.3-rc2
Minor SPI device driver changes. A rename of the pch_spi_pcidev symbol
that merely eliminates a modpost warning, and a Kconfig change to allow
the Samsung spi driver to build on EXYNOS.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi-topcliff-pch: rename pch_spi_pcidev to pch_spi_pcidev_driver
spi: Add spi-s3c64xx driver dependency on ARCH_EXYNOS4
Linus Torvalds [Thu, 9 Feb 2012 03:04:47 +0000 (19:04 -0800)]
Merge branch 'akpm' (Andrew's tree)
Five fixes
* branch 'akpm':
pcmcia: fix socket refcount decrementing on each resume
mm: fix UP THP spin_is_locked BUGs
drivers/leds/leds-lm3530.c: fix setting pltfm->als_vmax
mm: compaction: check for overlapping nodes during isolation for migration
nilfs2: avoid overflowing segment numbers in nilfs_ioctl_clean_segments()
Russell King [Thu, 9 Feb 2012 01:13:41 +0000 (17:13 -0800)]
pcmcia: fix socket refcount decrementing on each resume
This fixes a memory-corrupting bug: not only does it cause the warning,
but as a result of dropping the refcount to zero, it causes the
pcmcia_socket0 device structure to be freed while it still has
references, causing slab caches corruption. A fatal oops quickly
follows this warning - often even just a 'dmesg' following the warning
causes the kernel to oops.
While testing suspend/resume on an ARM device with PCMCIA support, and a
CF card inserted, I found that after five suspend and resumes, the
kernel would complain, and shortly die after with slab corruption.
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
As the message doesn't give a clue about which kobject, and the built-in
debugging in drivers/base/power/main.c happens too late, this was added
right before each get_device():
printk("%s: %p [%s] %u\n", __func__, dev, kobject_name(&dev->kobj), atomic_read(&dev->kobj.kref.refcount));
and on the 3rd s2ram cycle, the following behaviour observed:
On the 3rd suspend/resume cycle:
dpm_prepare:
c1a0d998 [pcmcia_socket0] 3
dpm_suspend:
c1a0d998 [pcmcia_socket0] 3
dpm_suspend_noirq:
c1a0d998 [pcmcia_socket0] 3
dpm_resume_noirq:
c1a0d998 [pcmcia_socket0] 3
dpm_resume:
c1a0d998 [pcmcia_socket0] 3
dpm_complete:
c1a0d998 [pcmcia_socket0] 2
4th:
dpm_prepare:
c1a0d998 [pcmcia_socket0] 2
dpm_suspend:
c1a0d998 [pcmcia_socket0] 2
dpm_suspend_noirq:
c1a0d998 [pcmcia_socket0] 2
dpm_resume_noirq:
c1a0d998 [pcmcia_socket0] 2
dpm_resume:
c1a0d998 [pcmcia_socket0] 2
dpm_complete:
c1a0d998 [pcmcia_socket0] 1
5th:
dpm_prepare:
c1a0d998 [pcmcia_socket0] 1
dpm_suspend:
c1a0d998 [pcmcia_socket0] 1
dpm_suspend_noirq:
c1a0d998 [pcmcia_socket0] 1
dpm_resume_noirq:
c1a0d998 [pcmcia_socket0] 1
dpm_resume:
c1a0d998 [pcmcia_socket0] 1
dpm_complete:
c1a0d998 [pcmcia_socket0] 0
------------[ cut here ]------------
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
Modules linked in: ucb1x00_core
Backtrace:
[<
c0212090>] (dump_backtrace+0x0/0x110) from [<
c04799dc>] (dump_stack+0x18/0x1c)
[<
c04799c4>] (dump_stack+0x0/0x1c) from [<
c021cba0>] (warn_slowpath_common+0x50/0x68)
[<
c021cb50>] (warn_slowpath_common+0x0/0x68) from [<
c021cbdc>] (warn_slowpath_null+0x24/0x28)
[<
c021cbb8>] (warn_slowpath_null+0x0/0x28) from [<
c0335374>] (kobject_get+0x28/0x50)
[<
c033534c>] (kobject_get+0x0/0x50) from [<
c03804f4>] (get_device+0x1c/0x24)
[<
c0388c90>] (dpm_complete+0x0/0x1a0) from [<
c0389cc0>] (dpm_resume_end+0x1c/0x20)
...
Looking at commit
7b24e7988263 ("pcmcia: split up central event handler"),
the following change was made to cs.c:
return 0;
}
#endif
-
- send_event(skt, CS_EVENT_PM_RESUME, CS_EVENT_PRI_LOW);
+ if (!(skt->state & SOCKET_CARDBUS) && (skt->callback))
+ skt->callback->early_resume(skt);
return 0;
}
And the corresponding change in ds.c is from:
-static int ds_event(struct pcmcia_socket *skt, event_t event, int priority)
-{
- struct pcmcia_socket *s = pcmcia_get_socket(skt);
...
- switch (event) {
...
- case CS_EVENT_PM_RESUME:
- if (verify_cis_cache(skt) != 0) {
- dev_dbg(&skt->dev, "cis mismatch - different card\n");
- /* first, remove the card */
- ds_event(skt, CS_EVENT_CARD_REMOVAL, CS_EVENT_PRI_HIGH);
- mutex_lock(&s->ops_mutex);
- destroy_cis_cache(skt);
- kfree(skt->fake_cis);
- skt->fake_cis = NULL;
- s->functions = 0;
- mutex_unlock(&s->ops_mutex);
- /* now, add the new card */
- ds_event(skt, CS_EVENT_CARD_INSERTION,
- CS_EVENT_PRI_LOW);
- }
- break;
...
- }
- pcmcia_put_socket(s);
- return 0;
-} /* ds_event */
to:
+static int pcmcia_bus_early_resume(struct pcmcia_socket *skt)
+{
+ if (!verify_cis_cache(skt)) {
+ pcmcia_put_socket(skt);
+ return 0;
+ }
+ dev_dbg(&skt->dev, "cis mismatch - different card\n");
+ /* first, remove the card */
+ pcmcia_bus_remove(skt);
+ mutex_lock(&skt->ops_mutex);
+ destroy_cis_cache(skt);
+ kfree(skt->fake_cis);
+ skt->fake_cis = NULL;
+ skt->functions = 0;
+ mutex_unlock(&skt->ops_mutex);
+ /* now, add the new card */
+ pcmcia_bus_add(skt);
+ return 0;
+}
As can be seen, the original function called pcmcia_get_socket() and
pcmcia_put_socket() around the guts, whereas the replacement code
calls pcmcia_put_socket() only in one path. This creates an imbalance
in the refcounting.
Testing with pcmcia_put_socket() put removed shows that the bug is gone:
dpm_suspend:
c1a10998 [pcmcia_socket0] 5
dpm_suspend_noirq:
c1a10998 [pcmcia_socket0] 5
dpm_resume_noirq:
c1a10998 [pcmcia_socket0] 5
dpm_resume:
c1a10998 [pcmcia_socket0] 5
dpm_complete:
c1a10998 [pcmcia_socket0] 5
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 9 Feb 2012 01:13:40 +0000 (17:13 -0800)]
mm: fix UP THP spin_is_locked BUGs
Fix CONFIG_TRANSPARENT_HUGEPAGE=y CONFIG_SMP=n CONFIG_DEBUG_VM=y
CONFIG_DEBUG_SPINLOCK=n kernel: spin_is_locked() is then always false,
and so triggers some BUGs in Transparent HugePage codepaths.
asm-generic/bug.h mentions this problem, and provides a WARN_ON_SMP(x);
but being too lazy to add VM_BUG_ON_SMP, BUG_ON_SMP, WARN_ON_SMP_ONCE,
VM_WARN_ON_SMP_ONCE, just test NR_CPUS != 1 in the existing VM_BUG_ONs.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Axel Lin [Thu, 9 Feb 2012 01:13:39 +0000 (17:13 -0800)]
drivers/leds/leds-lm3530.c: fix setting pltfm->als_vmax
In current code, pltfm->als_vmin is set to LM3530_ALS_WINDOW_mV and
pltfm->als_vmax is 0. This does not make sense. I think what we want
here is setting pltfm->als_vmax to LM3530_ALS_WINDOW_mV.
Both als_vmin and als_vmax local variables will be set to
pltfm->als_vmin and pltfm->als_vmax by a few lines latter. Thus also
remove a redundant assignment for als_vmin and als_vmax in this patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 9 Feb 2012 01:13:38 +0000 (17:13 -0800)]
mm: compaction: check for overlapping nodes during isolation for migration
When isolating pages for migration, migration starts at the start of a
zone while the free scanner starts at the end of the zone. Migration
avoids entering a new zone by never going beyond the free scanned.
Unfortunately, in very rare cases nodes can overlap. When this happens,
migration isolates pages without the LRU lock held, corrupting lists
which will trigger errors in reclaim or during page free such as in the
following oops
BUG: unable to handle kernel NULL pointer dereference at
0000000000000008
IP: [<
ffffffff810f795c>] free_pcppages_bulk+0xcc/0x450
PGD
1dda554067 PUD
1e1cb58067 PMD 0
Oops: 0000 [#1] SMP
CPU 37
Pid: 17088, comm: memcg_process_s Tainted: G X
RIP: free_pcppages_bulk+0xcc/0x450
Process memcg_process_s (pid: 17088, threadinfo
ffff881c2926e000, task
ffff881c2926c0c0)
Call Trace:
free_hot_cold_page+0x17e/0x1f0
__pagevec_free+0x90/0xb0
release_pages+0x22a/0x260
pagevec_lru_move_fn+0xf3/0x110
putback_lru_page+0x66/0xe0
unmap_and_move+0x156/0x180
migrate_pages+0x9e/0x1b0
compact_zone+0x1f3/0x2f0
compact_zone_order+0xa2/0xe0
try_to_compact_pages+0xdf/0x110
__alloc_pages_direct_compact+0xee/0x1c0
__alloc_pages_slowpath+0x370/0x830
__alloc_pages_nodemask+0x1b1/0x1c0
alloc_pages_vma+0x9b/0x160
do_huge_pmd_anonymous_page+0x160/0x270
do_page_fault+0x207/0x4c0
page_fault+0x25/0x30
The "X" in the taint flag means that external modules were loaded but but
is unrelated to the bug triggering. The real problem was because the PFN
layout looks like this
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x01e80000
Movable zone start PFN for each node
early_node_map[14] active PFN ranges
0: 0x00000010 -> 0x0000009b
0: 0x00000100 -> 0x0007a1ec
0: 0x0007a354 -> 0x0007a379
0: 0x0007f7ff -> 0x0007f800
0: 0x00100000 -> 0x00680000
1: 0x00680000 -> 0x00e80000
0: 0x00e80000 -> 0x01080000
1: 0x01080000 -> 0x01280000
0: 0x01280000 -> 0x01480000
1: 0x01480000 -> 0x01680000
0: 0x01680000 -> 0x01880000
1: 0x01880000 -> 0x01a80000
0: 0x01a80000 -> 0x01c80000
1: 0x01c80000 -> 0x01e80000
The fix is straight-forward. isolate_migratepages() has to make a
similar check to isolate_freepage to ensure that it never isolates pages
from a zone it does not hold the LRU lock for.
This was discovered in a 3.0-based kernel but it affects 3.1.x, 3.2.x
and current mainline.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xi Wang [Thu, 9 Feb 2012 01:13:37 +0000 (17:13 -0800)]
nilfs2: avoid overflowing segment numbers in nilfs_ioctl_clean_segments()
nsegs is read from userspace. Limit its value and avoid overflowing nsegs
* sizeof(__u64) in the subsequent call to memdup_user().
This patch complements
481fe17e973fb9 ("nilfs2: potential integer overflow
in nilfs_ioctl_clean_segments()").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Haogang Chen <haogangchen@gmail.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 8 Feb 2012 22:56:39 +0000 (14:56 -0800)]
Merge tag 'sound-fixes' of git://git./linux/kernel/git/tiwai/sound
sound fixes #2 for 3.3-rc3
A collection of small fixes, mostly for regressions.
In addition, a few ASoC wm8994 updates are included, too.
* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Disable line output discharge prior to ramping VMID
ASoC: wm8994: Fix typo in VMID ramp setting
ALSA: oxygen, virtuoso: fix exchanged L/R volumes of aux and CD inputs
ALSA: usb-audio: add Edirol UM-3G support
ALSA: hda - add support for Uniwill ECS M31EI notebook
ALSA: hda - Fix error handling in patch_ca0132.c
ASoC: wm8994: Enabling VMID should take a runtime PM reference
ALSA: hda/realtek - Fix a wrong condition
ALSA: emu8000: Remove duplicate linux/moduleparam.h include from emu8000_patch.c
ALSA: hda/realtek - Add missing Bass and CLFE as vmaster slaves
ASoC: wm_hubs: Correct line input to line output 2 paths
ASoC: cs42l73: Fix Output [X|A|V]SP_SCLK Sourcing Mode setting for master mode
ASoC: wm8962: Fix word length configuration
ASoC: core: Better support for idle_bias_off suspend ignores
ASoC: wm8994: Remove ASoC level register cache sync
ASoC: wm_hubs: Fix routing of input PGAs to line output mixer
Takashi Iwai [Wed, 8 Feb 2012 20:29:38 +0000 (21:29 +0100)]
Merge tag 'asoc-3.3' of git://git./linux/kernel/git/broonie/sound into for-linus
A few small WM8994 updates to go on top of the previous lot of things
that were sent. They collide with some -next work so I'd really like to
get them into 3.3-rc3 if possible to merge back up into the -next code.
All driver specific and unexciting in the grand scheme of things.
Mark Brown [Tue, 7 Feb 2012 14:18:29 +0000 (14:18 +0000)]
ASoC: wm8994: Disable line output discharge prior to ramping VMID
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Tue, 7 Feb 2012 17:24:19 +0000 (17:24 +0000)]
ASoC: wm8994: Fix typo in VMID ramp setting
The VMID ramp rate is supposed to be 0x3, not 11b. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Clemens Ladisch [Sat, 4 Feb 2012 19:56:47 +0000 (20:56 +0100)]
ALSA: oxygen, virtuoso: fix exchanged L/R volumes of aux and CD inputs
The driver accidentally exchanged the left/right fields for stereo AC'97
mixer registers. This affected only the aux and CD inputs because the
line input bypasses the AC'97 codec and the mic input is mono; cards
without AC'97 (Xonar DS/DG/HDAV Slim, HG2PCI, HiFier) were not affected.
Reported-and-tested-by: Abby Cedar <abbycedar@yahoo.com.au>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.31+ <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Sat, 4 Feb 2012 19:51:43 +0000 (20:51 +0100)]
ALSA: usb-audio: add Edirol UM-3G support
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 7 Feb 2012 23:54:02 +0000 (15:54 -0800)]
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
Joe Perches [Fri, 3 Feb 2012 23:20:39 +0000 (15:20 -0800)]
checkpatch: Warn on code with 6+ tab indentation
Overly indented code should be refactored.
Suggest refactoring excessive indentation of of
if/else/for/do/while/switch statements.
For example:
$ cat t.c
#include <stdio.h>
#include <stdlib.h>
int main(int argc, char **argv)
{
if (1)
if (2)
if (3)
if (4)
if (5)
if (6)
if (7)
if (8)
;
return 0;
}
$ ./scripts/checkpatch.pl -f t.c
WARNING: Too many leading tabs - consider code refactoring
#12: FILE: t.c:12:
+ if (6)
WARNING: Too many leading tabs - consider code refactoring
#13: FILE: t.c:13:
+ if (7)
WARNING: Too many leading tabs - consider code refactoring
#14: FILE: t.c:14:
+ if (8)
total: 0 errors, 3 warnings, 17 lines checked
t.c has style problems, please review.
If any of these errors are false positives, please report
them to the maintainer, see CHECKPATCH in MAINTAINERS.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 7 Feb 2012 22:35:19 +0000 (14:35 -0800)]
Merge tag 'ib-srpt-fixes' of git://git./linux/kernel/git/roland/infiniband
Cleanups and error path fixes for the new SRP (SCSI RDMA protocol) target.
* tag 'ib-srpt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/srpt: Don't return freed pointer from srpt_alloc_ioctx_ring()
IB/srpt: Fix ERR_PTR() vs. NULL checking confusion
IB/srpt: Remove unneeded <linux/version.h> include
IB/srpt: Use ARRAY_SIZE() instead of open-coding
IB/srpt: Use DEFINE_SPINLOCK()/LIST_HEAD()
Linus Torvalds [Tue, 7 Feb 2012 22:32:24 +0000 (14:32 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/mst/vhost
arch: fix ioport mapping on mips,sh
Kevin Cernekee reported that recent cleanup that replaced pci_iomap with
a generic function failed to take into account the differences in io
port handling on mips and sh architectures.
Rather than revert the changes reintroducing the code duplication, this
patchset fixes this by adding ability for architectures to override
ioport mapping for pci devices.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
sh: use the the PCI channels's io_map_base
mips: use the the PCI controller's io_map_base
lib: add NO_GENERIC_PCI_IOPORT_MAP
Yinghai Lu [Tue, 7 Feb 2012 16:20:37 +0000 (08:20 -0800)]
ACPI: remove duplicated lines of merging problems with acpi_processor_add
Those lines have two copies.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 7 Feb 2012 22:07:20 +0000 (14:07 -0800)]
Merge git://git.samba.org/sfrench/cifs-2.6
* git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix oops in session setup code for null user mounts
[CIFS] Update cifs Kconfig title to match removal of experimental dependency
cifs: fix printk format warnings
cifs: check offset in decode_ntlmssp_challenge()
cifs: NULL dereference on allocation failure
Linus Torvalds [Tue, 7 Feb 2012 22:06:11 +0000 (14:06 -0800)]
Merge branch 'upstream-fixes' of git://git./linux/kernel/git/jikos/hid
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wiimote: fix invalid power_supply_powers call
HID: wacom: Fix invalid power_supply_powers calls
HID: hyperv: Properly disconnect the input device
HID: usbhid: fix dead lock between open and disconect
Linus Torvalds [Tue, 7 Feb 2012 22:05:49 +0000 (14:05 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Avoid twl6040-codec PLL reconfiguration when not needed
mfd: Store twl6040-codec mclk configuration
Jaroslav Kysela [Tue, 7 Feb 2012 13:18:14 +0000 (14:18 +0100)]
ALSA: hda - add support for Uniwill ECS M31EI notebook
This hardware requires same fixup for the node 0x0f like Asus A6Rp.
More information: https://bugzilla.redhat.com/show_bug.cgi?id=785417
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jiri Kosina [Tue, 7 Feb 2012 12:40:56 +0000 (13:40 +0100)]
HID: wiimote: fix invalid power_supply_powers call
Analogically to
d7cb3dbd1 ("HID: wacom: Fix invalid power_supply_powers
calls"), fix also the same occurence in wiimote driver.
Reported-by: przemo@firszt.eu
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This page took 0.047732 seconds and 5 git commands to generate.