Brian Niebuhr [Fri, 1 Oct 2010 04:59:29 +0000 (10:29 +0530)]
spi: davinci: always start receive DMA
In keeping with the full duplex nature of the SPI bus. Always
start receive DMA along with transmit DMA.
If there is no receive buffer provided with the transfer, use
a temporary buffer to receive the data to be thrown away.
[michael.williamson@criticallink.com: receive DMA size should
be same as transfer length to avoid hang-up when transfer length
is smaller than temporary rx buffer size (rx buffer not provided)]
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Wed, 29 Sep 2010 07:01:54 +0000 (12:31 +0530)]
spi: davinci: do not use temporary buffer if no transmit data provided
Remove usage of temporary buffer when no transmit data is provided.
Instead, use the transmit register itself as the source of data.
By choosing the transmit register itself as the source of data, this
patch helps remove unnecessary accesses to memory when no real data
is being transmitted.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Tue, 28 Sep 2010 08:29:26 +0000 (13:59 +0530)]
spi: davinci: always start transmit DMA
Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.
The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.
However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.
Fix this by starting transmit DMA always.
This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Mon, 27 Sep 2010 16:53:23 +0000 (22:23 +0530)]
spi: davinci: do not store DMA channel information per chip select
Do not store DMA channel related information per chip-select since
that information does not depend on the chip select.
The same DMA channels can be used for transfers on all chip-selects
since the transfer happens one-at-a-time.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 24 Sep 2010 13:23:32 +0000 (18:53 +0530)]
spi: davinci: remove unnecessary call to davinci_spi_setup_transfer()
Remove unnecessary call to davinci_spi_setup_transfer() at the end
of davinci_spi_setup().
davinci_spi_setup_transfer() is registered as the setup_transfer
callback for the bitbang layer and is called independently by
the bitbang layer to setup the transfer before it begins.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 3 Sep 2010 06:45:28 +0000 (12:15 +0530)]
spi: davinci: remove unnecessary function davinci_spi_bufs_prep()
The function davinci_spi_bufs_prep() is doing stuff that
davinci_spi_setup() is doing. Eliminate it and move the work
to davinci_spi_setup()
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 3 Sep 2010 06:26:35 +0000 (11:56 +0530)]
spi: davinci: configure the invariable bits in spipc0 only once
Configure the data-in, data-out and clock functionality pins
in SPIPC0 register only once during probe. No need to set these
bits for each transfer.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 2 Sep 2010 11:22:06 +0000 (16:52 +0530)]
spi: davinci: add support for interrupt mode
Add support for SPI interrupt mode operation.
Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.
Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Mon, 23 Aug 2010 11:09:19 +0000 (16:39 +0530)]
spi: davinci: simplify poll mode transfers
Use the fact that the get_tx and get_rx can now cope with
NULL buffer pointers to simplify the poll mode transfer
code.
While at it, check for SPI errors every transfer rather than
at the end of the whole transfer.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 20 Aug 2010 11:32:49 +0000 (17:02 +0530)]
spi: davinci: remove non-useful interrupt mode support
The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.
Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Mon, 23 Aug 2010 11:04:13 +0000 (16:34 +0530)]
spi: davinci: remove unnecessary completion variable initialization
The completion variable 'done' is unnecessarly initialized by
the function davinci_spi_bufs_dma() where as it is not used
for DMA transfers at all.
Remove the unnecessary initialization.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sekhar Nori [Fri, 20 Aug 2010 10:57:08 +0000 (16:27 +0530)]
spi: davinci: do not treat Tx interrupt being set as error
In davinci_spi_check_error(), Tx interrupt being set is
treated as error. This function is only meant to flag
bus error conditions and Tx interrupt being set at that
point is not a bus error but rather a driver bug.
Stop checking for Tx interrupt and flagging that as an
IO error.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 20 Aug 2010 09:58:23 +0000 (15:28 +0530)]
spi: davinci: remove unnecessary 'count' variable in driver private data
The variable count in DaVinci SPI driver's private data is
largely unused and its minor use can easily be eliminated.
Remove the variable.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 20 Aug 2010 09:23:47 +0000 (14:53 +0530)]
spi: davinci: remove unnecessary disable of SPI
In the davinci_spi_bufs_dma() function, SPI is briefly disabled
before enabling it immediately back again.
Remove this unnecessary disable.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 11:34:25 +0000 (17:04 +0530)]
spi: davinci: check for NULL buffer pointer before using it
In the davinci_spi_{tx|rx}_u{8|16}() functions, check for
buffer pointer being valid before using it. While providing
for better error checking, this change will help simplify
code in the caller.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 11:12:42 +0000 (16:42 +0530)]
spi: davinci: simplify calculation of edma acount value
The EDMA acount (called data_type in davinci_spi_bufs_dma())
is simply the bytes_per_word obtained in the transfer setup
function. The current code calculates the acount value from
bytes_per_word in a convoluted manner. Simplify the code.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 11:08:20 +0000 (16:38 +0530)]
spi: davinci: eliminate unnecessary update of davinci_spi->count
The count member of davinci_spi is internal to the driver and
is not shared with framework. Eliminate its unnecessary update.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 10:46:28 +0000 (16:16 +0530)]
spi: davinci: eliminate the single member structure davinci_spi_slave
The struct davinci_spi_slave has a single member. Eliminate it
and store the per-chipselect data in struct davinci_spi directly.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 10:11:41 +0000 (15:41 +0530)]
spi: davinci: remove unused members of davinci_spi_slave
Several members of struct davinci_spi_slave are unused in code.
Remove such members.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 09:37:38 +0000 (15:07 +0530)]
spi: davinci: add support for wait enable timeouts
Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).
While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 07:14:31 +0000 (12:44 +0530)]
spi: davinci: setup chip-select timers values only if timer enabled
Setup chip-select timers values only if timer is enabled
(timer_disbled in spi configuration is false).
As a nice side effect, this patch removes code duplicated in
davinci_spi_bufs_pio() and davinci_spi_bufs_dma().
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 19 Aug 2010 06:45:22 +0000 (12:15 +0530)]
spi: davinci: consolidate setup of SPIFMTn in one function
Consolidate the setup of SPIFMTn register under
davinci_spi_setup_transfer() simplifying the code
and avoiding unnecessary reads and writes to the
register.
The two inline functions {set|clear}_fmt_bits() can
be eliminated because of this.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Mon, 16 Aug 2010 09:35:51 +0000 (15:05 +0530)]
spi: davinci: make chip-slect specific parameters really chip-select specific
Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.
Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Mon, 16 Aug 2010 04:58:53 +0000 (10:28 +0530)]
spi: davinci: remove 'wait_enable' platform data member
The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.
The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 13 Aug 2010 07:57:23 +0000 (13:27 +0530)]
spi: davinci: simplify prescalar calculation
Simplify pre-scalar calculation and move it into a seprate
function.
Refuse to correct invalid pre-scalar values silently as this
might lead to unexpected bugs and lower performance. Instead
an error will force users to dig into the root-cause of the
issue.
While at it, remove some device specific checks on the maximum
SPI frequency. As the driver supports the SPI interface
implemented on various devices, it should only take care of core
SPI limitations and leave the device specific handling to platform
code.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 13 Aug 2010 05:27:44 +0000 (10:57 +0530)]
spi: davinci: enable GPIO lines to be used as chip selects
Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.
This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 12 Aug 2010 06:57:33 +0000 (12:27 +0530)]
spi: davinci: remove unnecessary data transmit on CS disable
On TI DaVinci's SPI controller, the SPIDAT1 register which
controls the chip slect status, also has data transmit register
in the lower 16 bits. Writing to the whole 32-bits triggers
an additional data transmit every time the chip select is disabled.
While most SPI slaves cope-up with this, some cannot. This
patch fixes this by doing a 16-bit write on the upper half
of the SPIDAT1 register
While at it, group the SPIGCR1 register related defines seperately
from SPIDAT1 register defines.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 13 Aug 2010 04:41:03 +0000 (10:11 +0530)]
spi: davinci: enable both activation and deactivation of chip-selects
Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.
With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().
Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Thu, 12 Aug 2010 07:19:05 +0000 (12:49 +0530)]
spi: davinci: set chip-select mode in SPIDEF only once
Quit writing the same constant value determining the chip-select
mode when no transmissions are in progress in davinci_spi_chipelect().
Instead just setup the SPIDEF register once during probe.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sekhar Nori [Fri, 8 Oct 2010 09:57:26 +0000 (15:27 +0530)]
spi: davinci: remove unnecessary typecast
The typecasting of SPI base address to davinci_spi_reg is
unused.
Remove it.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sekhar Nori [Fri, 20 Aug 2010 10:50:49 +0000 (16:20 +0530)]
spi: davinci: removed unused #defines
Remove unused defines from code which should help
in easy reading of code.
Also, use the opportuinity to keep the SPIGCR1
register defines together.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 3 Sep 2010 10:49:09 +0000 (16:19 +0530)]
spi: davinci: remove unused variable 'pdata'
The 'pdata' variable is unused in couple of routines.
Remove such occurences.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 3 Sep 2010 09:45:06 +0000 (15:15 +0530)]
spi: davinci: whitespace cleanup
Cleanup unnecessary white space from various
parts of the file.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Brian Niebuhr [Fri, 3 Sep 2010 09:20:07 +0000 (14:50 +0530)]
spi: davinci: fix checkpatch errors
Fix the following checkpatch error:
WARNING: unnecessary whitespace before a quoted newline
+ dev_info(&pdev->dev, "Controller at 0x%p \n", davinci_spi->base);
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Linus Torvalds [Thu, 18 Nov 2010 02:36:25 +0000 (18:36 -0800)]
hardirq.h: remove now-empty #ifdef/#endif pair
Commit
451a3c24b013 ("BKL: remove extraneous #include <smp_lock.h>")
removed the #include line that was the only thing that was surrounded by
the #ifdef/#endif.
So now that #ifdef is guarding nothing at all. Just remove it.
Reported-by: Byeong-ryeol Kim <brofkims@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 17 Nov 2010 22:58:36 +0000 (14:58 -0800)]
Fix build failure due to hwirq.h needing smp_lock.h
Arnd Bergmann did an automated scripting run to find left-over instances
of <linux/smp_lock.h>, and had made it trigger it on the normal BKL use
of lock_kernel and unlock_lernel (and apparently release_kernel_lock and
reacquire_kernel_lock too, used by the scheduler).
That resulted in commit
451a3c24b013 ("BKL: remove extraneous #include
<smp_lock.h>").
However, hardirq.h was the only remaining user of the old
'kernel_locked()' interface, and Arnd's script hadn't checked for that.
So depending on your configuration and what header files had been
included, you would get errors like "implicit declaration of function
'kernel_locked'" during the build.
The right fix is not to just re-instate the smp_lock.h include - it is
to just remove 'kernel_locked()' entirely, since the only use was this
one special low-level detail. Just make hardirq.h do it directly.
In fact this simplifies and clarifies the code, because some trivial
analysis makes it clear that hardirq.h only ever used _one_ of the two
definitions of kernel_locked(), so we can remove the other one entirely.
Reported-by: Zimny Lech <napohybelskurwysynom2010@gmail.com>
Reported-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Wed, 17 Nov 2010 15:26:56 +0000 (16:26 +0100)]
BKL: remove references to lock_kernel from comments
Lock_kernel is gone from the code, so the comments should be updated,
too. nfsd now uses lock_flocks instead of lock_kernel to protect
against posix file locks.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Wed, 17 Nov 2010 15:26:55 +0000 (16:26 +0100)]
BKL: remove extraneous #include <smp_lock.h>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Wed, 17 Nov 2010 15:26:53 +0000 (16:26 +0100)]
staging/stradis: mark as "depends on BKL"
The stradis driver is on its way out, but it should still be marked
correctly as depending on the big kernel lock. It could easily be
changed to not require it if someone decides to revive the driver and
port it to v4l2 in the process.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Nathan Laredo <laredo@gnu.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcus Meissner [Tue, 16 Nov 2010 10:46:03 +0000 (11:46 +0100)]
kernel: make /proc/kallsyms mode 400 to reduce ease of attacking
Making /proc/kallsyms readable only for root by default makes it
slightly harder for attackers to write generic kernel exploits by
removing one source of knowledge where things are in the kernel.
This is the second submit, discussion happened on this on first submit
and mostly concerned that this is just one hole of the sieve ... but
one of the bigger ones.
Changing the permissions of at least System.map and vmlinux is also
required to fix the same set, but a packaging issue.
Target of this starter patch and follow ups is removing any kind of
kernel space address information leak from the kernel.
[ Side note: the default of root-only reading is the "safe" value, and
it's easy enough to then override at any time after boot. The /proc
filesystem allows root to change the permissions with a regular
chmod, so you can "revert" this at run-time by simply doing
chmod og+r /proc/kallsyms
as root if you really want regular users to see the kernel symbols.
It does help some tools like "perf" figure them out without any
setup, so it may well make sense in some situations. - Linus ]
Signed-off-by: Marcus Meissner <meissner@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Eugene Teo <eugeneteo@kernel.org>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 17 Nov 2010 02:46:28 +0000 (18:46 -0800)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
nfs: Ignore kmemleak false positive in nfs_readdir_make_qstr
SUNRPC: Simplify rpc_alloc_iostats by removing pointless local variable
nfs: trivial: remove unused nfs_wait_event macro
NFS: readdir shouldn't read beyond the reply returned by the server
NFS: Fix a couple of regressions in readdir.
Revert "NFSv4: Fall back to ordinary lookup if nfs4_atomic_open() returns EISDIR"
Regression: fix mounting NFS when NFSv3 support is not compiled
NLM: Fix a regression in lockd
Linus Torvalds [Tue, 16 Nov 2010 23:20:05 +0000 (15:20 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix cross-sched-class wakeup preemption
sched: Fix runnable condition for stoptask
sched: Use group weight, idle cpu metrics to fix imbalances during idle
Linus Torvalds [Tue, 16 Nov 2010 23:18:17 +0000 (15:18 -0800)]
Merge branch 'pm-fixes' of git://git./linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / PM QoS: Fix reversed min and max
PM / OPP: Hide OPP configuration when SoCs do not provide an implementation
PM: Allow devices to be removed during late suspend and early resume
Linus Torvalds [Tue, 16 Nov 2010 22:31:03 +0000 (14:31 -0800)]
Merge branch 'futexes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Address compiler warnings in exit_robust_list
Jeff Garzik [Tue, 16 Nov 2010 07:10:29 +0000 (02:10 -0500)]
SCSI host lock push-down
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 16 Nov 2010 18:51:56 +0000 (10:51 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fix offset check for sysfs mmapped files
Linus Torvalds [Tue, 16 Nov 2010 17:27:13 +0000 (09:27 -0800)]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kprobes: Fix the return address of multiple kretprobes
[S390] kprobes: disable interrupts throughout
[S390] ftrace: build without frame pointers on s390
[S390] mm: add devmem_is_allowed() for STRICT_DEVMEM checking
[S390] vmlogrdr: purge after recording is switched off
[S390] cio: fix incorrect ccw_device_init_count
[S390] tape: add medium state notifications
[S390] fix get_user_pages_fast
Darrick J. Wong [Tue, 16 Nov 2010 17:13:41 +0000 (09:13 -0800)]
PCI: fix offset check for sysfs mmapped files
I just loaded 2.6.37-rc2 on my machines, and I noticed that X no longer starts.
Running an strace of the X server shows that it's doing this:
open("/sys/bus/pci/devices/0000:07:00.0/resource0", O_RDWR) = 10
mmap(NULL,
16777216, PROT_READ|PROT_WRITE, MAP_SHARED, 10, 0) = -1 EINVAL (Invalid argument)
This code seems to be asking for a shared read/write mapping of 16MB worth of
BAR0 starting at file offset 0, and letting the kernel assign a starting
address. Unfortunately, this -EINVAL causes X not to start. Looking into
dmesg, there's a complaint like so:
process "Xorg" tried to map 0x01000000 bytes at page 0x00000000 on 0000:07:00.0 BAR 0 (start 0x
96000000, size 0x
1000000)
...with the following code in pci_mmap_fits:
pci_start = (mmap_api == PCI_MMAP_SYSFS) ?
pci_resource_start(pdev, resno) >> PAGE_SHIFT : 0;
if (start >= pci_start && start < pci_start + size &&
start + nr <= pci_start + size)
It looks like the logic here is set up such that when the mmap call comes via
sysfs, the check in pci_mmap_fits wants vma->vm_pgoff to be between the
resource's start and end address, and the end of the vma to be no farther than
the end. However, the sysfs PCI resource files always start at offset zero,
which means that this test always fails for programs that mmap the sysfs files.
Given the comment in the original commit
3b519e4ea618b6943a82931630872907f9ac2c2b, I _think_ the old procfs files
require that the file offset be equal to the resource's base address when
mmapping.
I think what we want here is for pci_start to be 0 when mmap_api ==
PCI_MMAP_PROCFS. The following patch makes that change, after which the Matrox
and Mach64 X drivers work again.
Acked-by: Martin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Catalin Marinas [Thu, 11 Nov 2010 12:53:47 +0000 (12:53 +0000)]
nfs: Ignore kmemleak false positive in nfs_readdir_make_qstr
Strings allocated via kmemdup() in nfs_readdir_make_qstr() are
referenced from the nfs_cache_array which is stored in a page cache
page. Kmemleak does not scan such pages and it reports several false
positives. This patch annotates the string->name pointer so that
kmemleak does not consider it a real leak.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Bryan Schumaker <bjschuma@netapp.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Jesper Juhl [Sun, 7 Nov 2010 21:11:34 +0000 (22:11 +0100)]
SUNRPC: Simplify rpc_alloc_iostats by removing pointless local variable
Hi,
We can simplify net/sunrpc/stats.c::rpc_alloc_iostats() a bit by getting
rid of the unneeded local variable 'new'.
Please CC me on replies.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Jeff Layton [Fri, 12 Nov 2010 14:23:04 +0000 (09:23 -0500)]
nfs: trivial: remove unused nfs_wait_event macro
Nothing uses this macro anymore.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Joe Perches [Tue, 16 Nov 2010 05:17:27 +0000 (21:17 -0800)]
kernel/sysctl.c: Fix build failure with !CONFIG_PRINTK
Sigh...
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 16 Nov 2010 02:31:02 +0000 (18:31 -0800)]
Linux 2.6.37-rc2
Trond Myklebust [Tue, 16 Nov 2010 01:26:22 +0000 (20:26 -0500)]
NFS: readdir shouldn't read beyond the reply returned by the server
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Tue, 16 Nov 2010 01:26:22 +0000 (20:26 -0500)]
NFS: Fix a couple of regressions in readdir.
Fix up the issue that array->eof_index needs to be able to be set
even if array->size == 0.
Ensure that we catch all important memory allocation error conditions
and/or kmap() failures.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Wed, 3 Nov 2010 14:24:16 +0000 (10:24 -0400)]
Revert "NFSv4: Fall back to ordinary lookup if nfs4_atomic_open() returns EISDIR"
This reverts commit
80e60639f1b7c121a7fea53920c5a4b94009361a.
This change requires further fixes to ensure that the open doesn't
succeed if the lookup later results in a regular file being created.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Paulius Zaleckas [Sun, 31 Oct 2010 16:21:05 +0000 (18:21 +0200)]
Regression: fix mounting NFS when NFSv3 support is not compiled
Trying to mount NFS (root partition in my case) fails if CONFIG_NFS_V3
is not selected. nfs_validate_mount_data() returns EPROTONOSUPPORT,
because of this check:
#ifndef CONFIG_NFS_V3
if (args->version == 3)
goto out_v3_not_compiled;
#endif /* !CONFIG_NFS_V3 */
and args->version was always initialized to 3.
It was working in 2.6.36
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Tue, 2 Nov 2010 13:11:55 +0000 (09:11 -0400)]
NLM: Fix a regression in lockd
Nick Bowler reports:
There are no unusual messages on the client... but I just logged into
the server and I see lots of messages of the following form:
nfsd: request from insecure port (192.168.8.199:35766)!
nfsd: request from insecure port (192.168.8.199:35766)!
nfsd: request from insecure port (192.168.8.199:35766)!
nfsd: request from insecure port (192.168.8.199:35766)!
nfsd: request from insecure port (192.168.8.199:35766)!
Bisected to commit
9247685088398cf21bcb513bd2832b4cd42516c4 (SUNRPC:
Properly initialize sock_xprt.srcaddr in all cases)
Apparently, removing the 'transport->srcaddr.ss_family = family' from
xs_create_sock() triggers this due to nlmclnt_lookup_host() incorrectly
initialising the srcaddr family to AF_UNSPEC.
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Eric Paris [Mon, 15 Nov 2010 23:36:29 +0000 (18:36 -0500)]
capabilities/syslog: open code cap_syslog logic to fix build failure
The addition of CONFIG_SECURITY_DMESG_RESTRICT resulted in a build
failure when CONFIG_PRINTK=n. This is because the capabilities code
which used the new option was built even though the variable in question
didn't exist.
The patch here fixes this by moving the capabilities checks out of the
LSM and into the caller. All (known) LSMs should have been calling the
capabilities hook already so it actually makes the code organization
better to eliminate the hook altogether.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 15 Nov 2010 22:06:11 +0000 (14:06 -0800)]
Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arm: omap1: devices: need to return with a value
OMAP1: camera.h: add missing include
omap: dma: Add read-back to DMA interrupt handler to avoid spuriousinterrupts
OMAP2: Devkit8000: Fix mmc regulator failure
Linus Torvalds [Mon, 15 Nov 2010 22:05:44 +0000 (14:05 -0800)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83795) Check for BEEP pin availability
hwmon: (w83795) Clear intrusion alarm immediately
hwmon: (w83795) Read the intrusion state properly
hwmon: (w83795) Print the actual temperature channels as sources
hwmon: (w83795) List all usable temperature sources
hwmon: (w83795) Expose fan control method
hwmon: (w83795) Fix fan control mode attributes
hwmon: (lm95241) Check validity of input values
hwmon: Change mail address of Hans J. Koch
Linus Torvalds [Mon, 15 Nov 2010 22:03:17 +0000 (14:03 -0800)]
Merge branch 'i2c-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Sanity checks on adapter registration
i2c: Mark i2c_adapter.id as deprecated
i2c: Drivers shouldn't include <linux/i2c-id.h>
i2c: Delete unused adapter IDs
i2c: Remove obsolete cleanup for clientdata
Linus Torvalds [Mon, 15 Nov 2010 22:01:33 +0000 (14:01 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: sysfs: fix printk warnings
PCI: fix pci_bus_alloc_resource() hang, prefer positive decode
PCI: read current power state at enable time
PCI: fix size checks for mmap() on /proc/bus/pci files
x86/PCI: coalesce overlapping host bridge windows
PCI hotplug: ibmphp: Add check to prevent reading beyond mapped area
Colin Cross [Mon, 15 Nov 2010 21:45:22 +0000 (22:45 +0100)]
PM / PM QoS: Fix reversed min and max
pm_qos_get_value had min and max reversed, causing all pm_qos
requests to have no effect.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: mark <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@kernel.org
Jean Delvare [Mon, 15 Nov 2010 21:40:38 +0000 (22:40 +0100)]
i2c: Sanity checks on adapter registration
Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Mon, 15 Nov 2010 21:40:38 +0000 (22:40 +0100)]
i2c: Mark i2c_adapter.id as deprecated
It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Jean Delvare [Mon, 15 Nov 2010 21:40:38 +0000 (22:40 +0100)]
i2c: Drivers shouldn't include <linux/i2c-id.h>
Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Mon, 15 Nov 2010 21:40:38 +0000 (22:40 +0100)]
i2c: Delete unused adapter IDs
Delete unused I2C adapter IDs. Special cases are:
* I2C_HW_B_RIVA was still set in driver rivafb, however no other
driver is ever looking for this value, so we can safely remove it.
* I2C_HW_B_HDPVR is used in staging driver lirc_zilog, however no
adapter ID is ever set to this value, so the code in question never
runs. As the code additionally expects that I2C_HW_B_HDPVR may not
be defined, we can delete it now and let the lirc_zilog driver
maintainer rewrite this piece of code.
Big thanks for Hans Verkuil for doing all the hard work :)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Wolfram Sang [Mon, 15 Nov 2010 21:40:38 +0000 (22:40 +0100)]
i2c: Remove obsolete cleanup for clientdata
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Linus Torvalds [Mon, 15 Nov 2010 21:37:37 +0000 (13:37 -0800)]
include/linux/kernel.h: Move logging bits to include/linux/printk.h
Move the logging bits from kernel.h into printk.h so that
there is a bit more logical separation of the generic from
the printk logging specific parts.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jim Bos [Mon, 15 Nov 2010 20:22:37 +0000 (21:22 +0100)]
Fix gcc 4.5.1 miscompiling drivers/char/i8k.c (again)
The fix in commit
6b4e81db2552 ("i8k: Tell gcc that *regs gets
clobbered") to work around the gcc miscompiling i8k.c to add "+m
(*regs)" caused register pressure problems and a build failure.
Changing the 'asm' statement to 'asm volatile' instead should prevent
that and works around the gcc bug as well, so we can remove the "+m".
[ Background on the gcc bug: a memory clobber fails to mark the function
the asm resides in as non-pure (aka "__attribute__((const))"), so if
the function does nothing else that triggers the non-pure logic, gcc
will think that that function has no side effects at all. As a result,
callers will be mis-compiled.
Adding the "+m" made gcc see that it's not a pure function, and so
does "asm volatile". The problem was never really the need to mark
"*regs" as changed, since the memory clobber did that part - the
problem was just a bug in the gcc "pure" function analysis - Linus ]
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Acked-by: Jakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean Delvare [Mon, 15 Nov 2010 20:38:57 +0000 (21:38 +0100)]
hwmon: (w83795) Check for BEEP pin availability
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:57 +0000 (21:38 +0100)]
hwmon: (w83795) Clear intrusion alarm immediately
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) Read the intrusion state properly
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) Print the actual temperature channels as sources
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) List all usable temperature sources
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) Expose fan control method
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (w83795) Fix fan control mode attributes
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Jean Delvare [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: (lm95241) Check validity of input values
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
Hans J. Koch [Mon, 15 Nov 2010 20:38:56 +0000 (21:38 +0100)]
hwmon: Change mail address of Hans J. Koch
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Randy Dunlap [Sat, 13 Nov 2010 16:44:33 +0000 (08:44 -0800)]
PCI: sysfs: fix printk warnings
Cast pci_resource_start() and pci_resource_len() to u64 for printk.
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 9 has type 'resource_size_t'
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 10 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linus Torvalds [Mon, 15 Nov 2010 16:43:29 +0000 (08:43 -0800)]
Merge git://git./linux/kernel/git/steve/gfs2-2.6-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Fix inode deallocation race
Linus Torvalds [Mon, 15 Nov 2010 16:43:04 +0000 (08:43 -0800)]
Merge branch 's5p-fixes-for-linus' of git://git./linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Fix HAVE_S3C_RTC warnings
ARM: SAMSUNG: Fix HAVE_S3C2410_I2C warnings
ARM: SAMSUNG: Fix HAVE_S3C2410_WATCHDOG warnings
Linus Torvalds [Mon, 15 Nov 2010 16:42:07 +0000 (08:42 -0800)]
Merge branch 'fbdev-fixes-for-linus' of git://git./linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fsl-diu-fb: drop dead ioctl define
MAINTAINERS: Add an fbdev git tree entry.
OMAP: DSS: Fix documentation regarding 'vram' kernel parameter
OMAP: VRAM: Fix boot-time memory allocation
OMAP: VRAM: improve VRAM error prints
sisfb: limit POST memory test according to PCI resource length
fbdev: sh_mobile_lcdc: use correct number of modes, when using the default
fbdev: sh_mobile_lcdc: use the standard CEA-861 720p timing
fbdev: sh_mobile_hdmi: properly clean up modedb on monitor unplug
Linus Torvalds [Mon, 15 Nov 2010 16:41:30 +0000 (08:41 -0800)]
Merge branches 'sh-fixes-for-linus' and 'rmobile-fixes-for-linus' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: intc: Fix up build failure introduced by radix tree changes.
MAINTAINERS: update the sh git tree entry.
sh: clkfwk: fix up compiler warnings.
sh: intc: Fix up initializers for gcc 4.5.
rtc: rtc-sh - fix a memory leak
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
MAINTAINERS: update the ARM SH-Mobile git tree entry.
ARM: mach-shmobile: ap4evb: Mark NOR boot loader partitions read-only.
ARM: mach-shmobile: intc-sh7372: fix interrupt number
Steven Whitehouse [Wed, 3 Nov 2010 20:01:07 +0000 (20:01 +0000)]
GFS2: Fix inode deallocation race
This area of the code has always been a bit delicate due to the
subtleties of lock ordering. The problem is that for "normal"
alloc/dealloc, we always grab the inode locks first and the rgrp lock
later.
In order to ensure no races in looking up the unlinked, but still
allocated inodes, we need to hold the rgrp lock when we do the lookup,
which means that we can't take the inode glock.
The solution is to borrow the technique already used by NFS to solve
what is essentially the same problem (given an inode number, look up
the inode carefully, checking that it really is in the expected
state).
We cannot do that directly from the allocation code (lock ordering
again) so we give the job to the pre-existing delete workqueue and
carry on with the allocation as normal.
If we find there is no space, we do a journal flush (required anyway
if space from a deallocation is to be released) which should block
against the pending deallocations, so we should always get the space
back.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Paul Mundt [Mon, 15 Nov 2010 05:47:16 +0000 (14:47 +0900)]
Merge branch 'rmobile/core' into rmobile-fixes-for-linus
Kuninori Morimoto [Mon, 15 Nov 2010 03:11:09 +0000 (03:11 +0000)]
ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
Tested-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Tested-by: TAKEI Mitsuharu <takei.andr@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Mon, 15 Nov 2010 05:30:30 +0000 (14:30 +0900)]
sh: intc: Fix up build failure introduced by radix tree changes.
The radix tree retry logic got a bit of an overhaul and subsequently
broke the virtual IRQ subgroup build. Simply switch over to
radix_tree_deref_retry() as per the filemap changes, which the virq
lookup logic was modelled after in the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Mon, 15 Nov 2010 04:54:00 +0000 (13:54 +0900)]
Merge branch 'master' of git://git./linux/kernel/git/torvalds/linux-2.6 into sh/urgent
Mike Frysinger [Sat, 13 Nov 2010 07:06:27 +0000 (02:06 -0500)]
fsl-diu-fb: drop dead ioctl define
The fsl-diu-fb driver no longer uses this define, and we have a common one
to cover this already (FBIO_WAITFORVSYNC).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Mon, 15 Nov 2010 04:25:31 +0000 (13:25 +0900)]
MAINTAINERS: Add an fbdev git tree entry.
Now that there's an fbdev git tree (this is also what is pulled in to
-next), stub it in to the MAINTAINERS entry.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds [Sun, 14 Nov 2010 21:06:37 +0000 (13:06 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: Fix slub_lock down/up imbalance
Linus Torvalds [Sun, 14 Nov 2010 21:04:53 +0000 (13:04 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Change some lock status member in ocfs2_lock_res to char.
Pavel Emelyanov [Thu, 28 Oct 2010 09:50:37 +0000 (13:50 +0400)]
slub: Fix slub_lock down/up imbalance
There are two places, that do not release the slub_lock.
Respective bugs were introduced by sysfs changes
ab4d5ed5 (slub: Enable
sysfs support for !CONFIG_SLUB_DEBUG) and
2bce6485 ( slub: Allow removal
of slab caches during boot).
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Linus Torvalds [Sat, 13 Nov 2010 18:00:15 +0000 (10:00 -0800)]
Merge branch 'urgent' of git://git./linux/kernel/git/brodo/pcmcia-2.6
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
drivers/pcmcia/soc_common.c: Use printf extension %pV
pcmcia: fix warning in synclink driver
pcmcia/sa1100: don't put machine specific init functions in .init.text
pcmcia/cm4000: fix error code
pd6729: Coding Style fixes
Ingo Molnar [Sat, 13 Nov 2010 15:21:58 +0000 (16:21 +0100)]
Revert "8250: Fix tcsetattr to avoid ioctl(TIOCMIWAIT) hang"
This reverts commit
47d3904fe40d62deee8cd46e79ca784e7a548acd.
Crashes any x86 serial console bootup:
Console: colour VGA+ 80x25
BUG: unable to handle kernel NULL pointer dereference at
0000000000000158
IP: [<
ffffffff811ebcb4>] serial8250_do_set_termios+0x1d4/0x430
...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <gregkh@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 13 Nov 2010 17:55:56 +0000 (09:55 -0800)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: padlock - Fix AES-CBC handling on odd-block-sized input
crypto: n2 - dubious error check
Linus Torvalds [Sat, 13 Nov 2010 17:55:19 +0000 (09:55 -0800)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] soc-camera: Compile fixes for mx2-camera
[media] SoC Camera: ov6650: minor cleanups
[media] SOC Camera: OMAP1: typo fix
[media] SoC Camera: OMAP1: update for recent videobuf changes
[media] SoC Camera: OMAP1: update for recent framework changes
[media] ARM mx3_camera: check for DMA engine type
[media] tm6000: bugfix set tv standards
[media] cafe_ccic: fix subdev configuration
[media] saa7134: Fix autodetect for Behold A7 and H7 TV cards
[media] v4l: kill the BKL
[media] BZ#22292: dibx000_common: Restore i2c algo pointer
Jim Bos [Sat, 13 Nov 2010 11:13:53 +0000 (12:13 +0100)]
i8k: Tell gcc that *regs gets clobbered
More recent GCC caused the i8k driver to stop working, on Slackware
compiler was upgraded from gcc-4.4.4 to gcc-4.5.1 after which it didn't
work anymore, meaning the driver didn't load or gave total nonsensical
output.
As it turned out the asm(..) statement forgot to mention it modifies the
*regs variable.
Credits to Andi Kleen and Andreas Schwab for providing the fix.
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.048369 seconds and 5 git commands to generate.