PCI: eliminate double kfree in intel-iommu initialization

The destination of goto error also does a kfree(g_iommus), so it is not
correct to do one here.

This was found using Coccinelle (http://www.emn.fr/x-info/coccinelle/).

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pciehp: removes redundant NULL write to slot status register

Cleanup to remove a redundant NULL write to SLOTSTATUS.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pciehp: fixes typo in dbg_ctrl() in pciehp_hpc.c

Fixup a typo in dbg_ctrl(); it was fetching SLOTSTATUS twice.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

shpchp: check firmware before taking control

Fix the following problems of shpchp driver about getting hotplug
control from firmware.

  - The shpchp driver must not control the hotplug controller if it
    fails to get control from the firmware. But current shpchp
    controls the hotplug controller regardless the result, because it
    doesn't check the return value of get_hp_hw_control_from_firmware().

  - Current shpchp driver doesn't support _OSC.

The pciehp driver already have the code for evaluating _OSC and OSHP
and shpchp and pciehp can share it. So this patch move that code from
pciehp to acpi_pcihp.c.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pciehp: block signals while waiting for command completion

Since we need to wait for command completion for muximum 1sec, waiting
command should not be interrupted by a signal.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pciehp: evaluate _OSC/OSHP before controller init

Current pciehp evaluates _OSC/OSHP method after some controller
initialization is done. So if evaluating _OSC/OSHP is failed, we need
to cleanup already initialized data structures or hardware. This
clearly is not robust way. With this patch, _OSC/OSHP evaluation is
done first.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pciehp: remove redundant pci_dev initialization

Remove the redundant initialization of pci_dev member of struct
controller in pciehp_probe(). It is initialized in pcie_init().

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI/x86: early dump pci conf space v2

Allows us to dump PCI space before any kernel changes have been made.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI/x86: write_pci_config_byte fix offset

also add write_pci_config_16

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Implement new suspend and hibernation callbacks for platform busses

Implement new suspend and hibernation callbacks for the platform bus
type.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg KH <greg@kroah.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI: implement new suspend/resume callbacks

Implement new suspend and hibernation callbacks for the PCI bus type.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Introduce new top level suspend and hibernation callbacks

Introduce 'struct pm_ops' and 'struct pm_ext_ops' ('ext' meaning
'extended') representing suspend and hibernation operations for bus
types, device classes, device types and device drivers.

Modify the PM core to use 'struct pm_ops' and 'struct pm_ext_ops'
objects, if defined, instead of the ->suspend(), ->resume(),
->suspend_late(), and ->resume_early() callbacks (the old callbacks
will be considered as legacy and gradually phased out).

The main purpose of doing this is to separate suspend (aka S2RAM and
standby) callbacks from hibernation callbacks in such a way that the
new callbacks won't take arguments and the semantics of each of them
will be clearly specified.  This has been requested for multiple
times by many people, including Linus himself, and the reason is that
within the current scheme if ->resume() is called, for example, it's
difficult to say why it's been called (ie. is it a resume from RAM or
from hibernation or a suspend/hibernation failure etc.?).

The second purpose is to make the suspend/hibernation callbacks more
flexible so that device drivers can handle more than they can within
the current scheme.  For example, some drivers may need to prevent
new children of the device from being registered before their
->suspend() callbacks are executed or they may want to carry out some
operations requiring the availability of some other devices, not
directly bound via the parent-child relationship, in order to prepare
for the execution of ->suspend(), etc.

Ultimately, we'd like to stop using the freezing of tasks for suspend
and therefore the drivers' suspend/hibernation code will have to take
care of the handling of the user space during suspend/hibernation.
That, in turn, would be difficult within the current scheme, without
the new ->prepare() and ->complete() callbacks.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI: boot parameter to avoid expansion ROM memory allocation

Contention for scarce PCI memory resources has been growing
due to an increasing number of PCI slots in large multi-node
systems.  The kernel currently attempts by default to
allocate memory for all PCI expansion ROMs so there has
also been an increasing number of PCI memory allocation
failures seen on these systems.  This occurs because the
BIOS either (1) provides insufficient PCI memory resource
for all the expansion ROMs or (2) provides adequate PCI
memory resource for expansion ROMs but provides the
space in kernel unexpected BIOS assigned P2P non-prefetch
windows.

The resulting PCI memory allocation failures may be benign
when related to memory requests for expansion ROMs themselves
but in some cases they can occur when attempting to allocate
space for more critical BARs.  This can happen when a successful
expansion ROM allocation request consumes memory resource
that was intended for a non-ROM BAR.  We have seen this
happen during PCI hotplug of an adapter that contains a
P2P bridge where successful memory allocation for an
expansion ROM BAR on device behind the bridge consumed
memory that was intended for a non-ROM BAR on the P2P bridge.
In all cases the allocation failure messages can be very
confusing for users.

This patch provides a new 'pci=norom' kernel boot parameter
that can be used to disable the default PCI expansion ROM memory
resource allocation.  This provides a way to avoid the above
described issues on systems that do not contain PCI devices
for which drivers or user-level applications depend on the
default PCI expansion ROM memory resource allocation behavior.

Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI/MSI: skip calling pci_find_capability from msi_set_mask_bits

The position of MSI capability is already cached in the msi_desc when
we enter the msi_set_mask_bits().  Use it instead.

Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI: remove CVS keywords

This patch removes CVS keywords that weren't updated for a long time
from comments.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pci-acpi: formatting cleanups for _OSC

Minor cleanup in pci-acpi.c.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pci-acpi: remove unused variable in __pci_osc_support_set

The 'retval' variable in __pci_osc_support_set() is no longer
used. Remove this unused variable.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pci-acpi: add flag to indicate query had been done

Current pci-acpi implementation checks osc_data->support_stat to see
if control bits had been already queried. It is not good from the
viewpoint of easy understanding. So this patch adds new 'is_queried'
flag to indicate query had been done.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pci-acpi: use local buffer for _OSC

Current pci-acpi implementation uses array in osc_data directly to
evaluate _OSC. It needs to save the old data and restore it if _OSC
evaluation fails. To make it more robust, we should use local array to
evaluate _OSC.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

pci-acpi: remove duplicate code for _OSC

Remove the duplicated code in acpi_query_osc() and acpi_run_osc().
It simplifies the code very much.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI: Disable PME during PCI scan

If a device supports #PME and can generate PME events from D0, we may see
superfluous events before a driver is loaded (drivers should only enable PME as
needed), preventing suspend from working if the corresponding GPE was enabled.

Likewise, if the ACPI device has the _PRW object, the _PSW/_DSW object will be
called in order to disable the wakeup functionality. But when it is allowed to
wake up the sleeping state, OSPM will enable it again.

So we should disable PME in the course of scanning PCI devices and enable it
again only when PME events are actually required to be generated from the
requested PCI state (for example, D3_hot or D3_cold).  It is also safe to
disable PME again when the PME is disabled for the PCI devices.

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

Suspend/Resume bug in PCI layer wrt quirks

Some quirks should be called with interrupt disabled, we can't directly
call them in .resume_early. Also the patch introduces
pci_fixup_resume_early and pci_fixup_suspend, which matches current
device core callbacks (.suspend/.resume_early).

TBD: Somebody knows why we need quirk resume should double check if a
quirk should be called in resume or resume_early. I changed some per my
understanding, but can't make sure I fixed all.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

x86/PCI: janitor work in irq.c

Wrapped long lines, removed trailing whitespaces, fixed case indentation
inside switch and so.

Signed-off-by: Miklos Vajna <vmiklos@frugalware.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI: Replace deprecated __initcall with device_initcall.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI: drivers/pci/pci.c: add prototypes

This patch adds prototypes for pcibios_disable_device() and
pcibios_set_pcie_reset_state() in include/linux/pci.h

While I was at it, I also removed the unneeded "extern" from the
prototype of pcibios_add_platform_entries().

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

PCI: make {pciehp,shpchp}_slot_with_bus static

This patch makes the needlessly global {pciehp,shpchp}_slot_with_bus
static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>

MAINTAINERS: update PPPoE maintainer address

Cc: Michal Ostrowski <mostrows@earthlink.net>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/core: Remove IB_DEVICE_SEND_W_INV capability flag
  IB/umem: Avoid sign problems when demoting npages to integer

Merge git://git.infradead.org/users/cbou/battery-2.6.26

* git://git.infradead.org/users/cbou/battery-2.6.26:
  power_supply: Fix race in power_supply_uevent

Merge branch 'for-linus' of git://git./linux/kernel/git/cooloney/blackfin-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
  Blackfin serial driver: fix up tty core set_ldisc API change breakage bug
  Blackfin arch: protect only the SPI bus controller with CONFIG_SPI_BFIN
  Blackfin arch: fixup warnings with the new cplb saved values
  Blackfin Serial Driver: Clean up BF54x macro in blackfin UART driver.

power_supply: Fix race in power_supply_uevent

Commit 54d29ad33e3483bcc7ca433a21cf294854e5154a (Power Supply: fix race
in device_create) introduced a race in power_supply_uevent. Previously it
checked that power_supply is available by checking for dev->driver_data.
But now dev->driver_data is set before power_supply->dev is initialised.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>

Merge branch 'fixes' of git://git./linux/kernel/git/davej/cpufreq

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix format string bug.

[CPUFREQ] Fix format string bug.

Format string bug.  Not exploitable, as this is only writable by root,
but worth fixing all the same.

Spotted-by: Ilja van Sprundel <ilja@netric.org>
Signed-off-by: Dave Jones <davej@redhat.com>

Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  [ALSA] hda - Fix "alc262_sony_unsol[]" hda_verb array

Merge branch 'merge' of git://git./linux/kernel/git/paulus/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] ehea: Remove dependency on MEMORY_HOTPLUG
  [POWERPC] Make walk_memory_resource available with MEMORY_HOTPLUG=n
  [POWERPC] Use dev_set_name in pci_64.c
  [POWERPC] Fix incorrect enabling of VMX when building signal or user context
  [POWERPC] boot/Makefile CONFIG_ variable fixes

Merge git://git./linux/kernel/git/lethal/sh-2.6.26

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.26:
  sh: Add -mno-fdpic to default flags.
  sh: add resource of USB host for SH7723
  usb: r8a66597-hcd: Add support for SH7723 USB host
  sh: Fix compile error SH7763 setup code
  sh: Add SH7723 SCIF support

mm: Minor clean-up of page flags in mm/page_alloc.c

Minor source code cleanup of page flags in mm/page_alloc.c.
Move the definition of the groups of bits to page-flags.h.

The purpose of this clean up is that the next patch will
conditionally add a page flag to the groups.  Doing that
in a header file is cleaner than adding #ifdefs to the
C code.

Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix invalid access errors in blk_lookup_devt

Commit 30f2f0eb4bd2c43d10a8b0d872c6e5ad8f31c9a0 ("block: do_mounts -
accept root=<non-existant partition>") extended blk_lookup_devt() to be
able to look up partitions that had not yet been registered, but in the
process made the assumption that the '&block_class.devices' list only
contains disk devices and that you can do 'dev_to_disk(dev)' on them.

That isn't actually true.  The block_class device list also contains the
partitions we've discovered so far, and you can't just do a
'dev_to_disk()' on those.

So make sure to only work on devices that block/genhd.c has registered
itself, something we can test by checking the 'dev->type' member.  This
makes the loop in blk_lookup_devt() match the other such loops in this
file.

[ We may want to do an alternate version that knows to handle _either_
  whole-disk devices or partitions, but for now this is the minimal fix
  for a series of crashes reported by Mariusz Kozlowski in

http://lkml.org/lkml/2008/5/25/25

  and Ingo in

http://lkml.org/lkml/2008/6/9/39 ]

Reported-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Neil Brown <neilb@suse.de>
Cc: Joao Luis Meloni Assirati <assirati@nonada.if.usp.br>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

IB/core: Remove IB_DEVICE_SEND_W_INV capability flag

In 2.6.26, we added some support for send with invalidate work
requests, including a device capability flag to indicate whether a
device supports such requests.  However, the support was incomplete:
the completion structure was not extended with a field for the key
contained in incoming send with invalidate requests.

Full support for memory management extensions (send with invalidate,
local invalidate, fast register through a send queue, etc) is planned
for 2.6.27.  Since send with invalidate is not very useful by itself,
just remove the IB_DEVICE_SEND_W_INV bit before the 2.6.26 final
release; we will add an IB_DEVICE_MEM_MGT_EXTENSIONS bit in 2.6.27,
which makes things simpler for applications, since they will not have
quite as confusing an array of fine-grained bits to check.

Signed-off-by: Roland Dreier <rolandd@cisco.com>

[ALSA] hda - Fix "alc262_sony_unsol[]" hda_verb array

I think that hda_verb array must have "terminator (empty array)".
But alc262_sony_unsol[] does not have it.
And it causes gcc-4.3's buggy behavior
with snd_hda_sequence_write().

Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

sh: Add -mno-fdpic to default flags.

Presently the --fdpic specifier and the --isa matching clash when
building with FDPIC toolchains. As we have no interest in building the
kernel with --fdpic in the first place, always try to add in -mno-fdpic
to the default flags.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sh: add resource of USB host for SH7723

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

usb: r8a66597-hcd: Add support for SH7723 USB host

R8A66597 is similar to SH7723 USB 2.0 Host/Function module.
In addition, the USB of SH7366 is compatible with SH7723.
It can support SH7723 USB host by changing Kconfig.

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sh: Fix compile error SH7763 setup code

SH7763's setup code use old DECLARE_INTC_DESC.
There was a compile error because of this.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sh: Add SH7723 SCIF support

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

[POWERPC] ehea: Remove dependency on MEMORY_HOTPLUG

Now that walk_memory_resource() is available regardless of
MEMORY_HOTPLUG's setting, this dependency is not needed.

Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Make walk_memory_resource available with MEMORY_HOTPLUG=n

The ehea driver was recently changed[1] to use walk_memory_resource() to
detect the system's memory layout.  However, walk_memory_resource() is
available only when memory hotplug is enabled.  So CONFIG_EHEA was
made to depend on MEMORY_HOTPLUG [2], but it is inappropriate for a
network driver to have such a dependency.

Make the declaration of walk_memory_resource() and its powerpc
implementation (ehea is powerpc-specific) unconditionally available.

[1] 48cfb14f8b89d4d5b3df6c16f08b258686fb12ad
    "ehea: Add DLPAR memory remove support"

[2] fb7b6ca2b6b7c23b52be143bdd5f55a23b9780c8
    "ehea: Add dependency to Kconfig"

Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Use dev_set_name in pci_64.c

During the next merge window, pci_name()'s return value will become
const, so use the new dev_set_name() instead to avoid the warning (from
linux-next):

arch/powerpc/kernel/pci_64.c: In function 'of_create_pci_dev':
arch/powerpc/kernel/pci_64.c:193: warning: passing argument 1 of 'sprintf' discards qualifiers from pointer target type

Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] Fix incorrect enabling of VMX when building signal or user context

When building a signal or a ucontext, we can incorrectly set the MSR_VEC
bit of the kernel pt_regs->msr before returning to userspace if the task
-ever- used VMX.

This can lead to funny result if that stack used it in the past, then
"lost" it (ie. it wasn't enabled after a context switch for example)
and then called get_context.  It can end up with VMX enabled and the
registers containing values from some other task.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[POWERPC] boot/Makefile CONFIG_ variable fixes

This corrects the names of two CONFIG_ variables.

Note that the CONFIG_MPC86XADS fix uncovers another bug
(with mpc866_ads_defconfig) that will require fixing:

<--  snip  -->

...
arch/powerpc/boot/dtc -O dtb -o arch/powerpc/boot/mpc866ads.dtb -b 0  /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts
DTC: dts->dtb  on file "/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts"
  WRAP    arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1

<--  snip  -->

Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

fat_valid_media() isn't for userspace

Commit 73f20e58b1d586e9f6d3ddc3aad872829aca7743 ("FAT_VALID_MEDIA():
remove pointless test") wrongly added the new fat_valid_media() function
to the userspace-visible part of include/linux/msdos_fs.h

Move it to the part of include/linux/msdos_fs.h that is not exported to
userspace.

Reported-by: Onur Küçük <onur@pardus.org.tr>
Reported-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Blackfin serial driver: fix up tty core set_ldisc API change breakage bug

This is the patch that follows Linus's modification about set_ldisc.
Graf has built and tested it on BF537 using Linus's git Tree.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

Blackfin arch: protect only the SPI bus controller with CONFIG_SPI_BFIN

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>

IB/umem: Avoid sign problems when demoting npages to integer

On a 64-bit architecture, if ib_umem_get() is called with a size value
that is so big that npages is negative when cast to int, then the
length of the page list passed to get_user_pages(), namely

min_t(int, npages, PAGE_SIZE / sizeof (struct page *))

will be negative, and get_user_pages() will immediately return 0 (at
least since 900cf086, "Be more robust about bad arguments in
get_user_pages()").  This leads to an infinite loop in ib_umem_get(),
since the code boils down to:

while (npages) {
ret = get_user_pages(...);
npages -= ret;
}

Fix this by taking the minimum as unsigned longs, so that the value of
npages is never truncated.

The impact of this bug isn't too severe, since the value of npages is
checked against RLIMIT_MEMLOCK, so a process would need to have an
astronomical limit or have CAP_IPC_LOCK to be able to trigger this,
and such a process could already cause lots of mischief.  But it does
let buggy userspace code cause a kernel lock-up; for example I hit
this with code that passes a negative value into a memory registartion
function where it is promoted to a huge u64 value.

Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Merge branch 'for_linus' of git://git./linux/kernel/git/tytso/ext4

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: enable barriers by default
  jbd2: Fix barrier fallback code to re-lock the buffer head
  ext4: Display the journal_async_commit mount option in /proc/mounts
  jbd2: If a journal checksum error is detected, propagate the error to ext4
  jbd2: Fix memory leak when verifying checksums in the journal
  ext4: fix online resize bug
  ext4: Fix uninit block group initialization with FLEX_BG
  ext4: Fix use of uninitialized data with debug enabled.

uml: activate_mm: remove the dead PF_BORROWED_MM check

use_mm() was changed to use switch_mm() instead of activate_mm(), since
then nobody calls (and nobody should call) activate_mm() with
PF_BORROWED_MM bit set.

As Jeff Dike pointed out, we can also remove the "old != new" check, it is
always true.

Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/ipath: Fix SM trap forwarding
  IB/ehca: Reject send WRs only for RESET, INIT and RTR state
  MAINTAINERS: Update NetEffect (iw_nes) entry
  IB/ipath: Fix device capability flags
  IB/ipath: Avoid test_bit() on u64 SDMA status value

Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86/PCI: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
  PCI/x86: fix up PCI stuff so that PCI_GOANY supports OLPC

Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: emu10k1 - fix system hang with Audigy2 ZS Notebook PCMCIA card

Merge branch 'for-linus' of git://git./linux/kernel/git/chrisw/lsm-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/chrisw/lsm-2.6:
  capabilities: remain source compatible with 32-bit raw legacy capability support.
  LSM: remove stale web site from MAINTAINERS

Merge git://git.infradead.org/~dwmw2/mtd-2.6.26

* git://git.infradead.org/~dwmw2/mtd-2.6.26:
  [MTD] m25p80.c mutex unlock fix

ipwireless: Fix blocked sending

Packet sending is driven by two flags, tx_ready and tx_queued.
It was possible, that there were queued data for sending and
hardware was flagged as blocked but in fact it was not.

The tx_queued was indicator but should be really a counter else
first fragmented packet resets tx_queued flag, but there may be
pending packets which do not get sent.

New semantics:
tx_ready - set, if hw is ready to send packet, no packet is being
           transferred right now
           set the flag right at the place where data are copied
           into hw memory and not earlier without checking if it
           was succesful
tx_queued - count of enqueued packets, including fragments

Tested-by: Michal Rokos <michal.rokos@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vm: add kzalloc_node() inline

To get zeroed out memory from a particular NUMA node.  To be used by
sunrpc.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pagemap: add documentation for pagemap

Just a quick explanation of the pagemap interface from a userspace point
of view, and an example of how to use it (in English, not code).

Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pagemap: return EINVAL, not EIO, for unaligned reads of kpagecount or kpageflags

If the user tries to read from a position that is not a multiple of 8, or
read a number of bytes that is not a multiple of 8, they have passed an
invalid argument to read, for the purpose of reading these files.  It's
not an IO error because we didn't encounter any trouble finding the data
they asked for.

Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pagemap: return map count, not reference count, in /proc/kpagecount

Since pagemap is all about examining pages mapped into processes' memory
spaces, it makes sense for kpagecount to return the map counts, not the
reference counts.

Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hdaps: fix module loading on Thinkpad T61P

Adds DMI system identifier for ThinkPad T61.

Originally written by Klaus S. Madsen.

Taken from http://launchpadlibrarian.net/10864950/hdaps-t61.patch

Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Cc: Klaus S. Madsen <ubuntu@hjernemadsen.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: calculate the correct /proc/<pid> link count

This patch:

  commit e9720acd728a46cb40daa52c99a979f7c4ff195c
  Author: Pavel Emelyanov <xemul@openvz.org>
  Date:   Fri Mar 7 11:08:40 2008 -0800

    [NET]: Make /proc/net a symlink on /proc/self/net (v3)

introduced a /proc/self/net directory without bumping the corresponding
link count for /proc/self.

This patch replaces the static link count initializations with a call that
counts the number of directory entries in the given pid_entry table
whenever it is instantiated, and thus relieves the burden of manually
keeping the two in sync.

[akpm@linux-foundation.org: cleanup]
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: class driver for ppc_md RTC functions

This hooks up the platform-specific [gs]et_rtc_time functions so that
kernels using CONFIG_RTC_CLASS have RTC support on most PowerPC platforms.

A new driver, and one which we've been shipping in Fedora for a while
already, since otherwise RTC support breaks.

[akpm@linux-foundation.org: fix Kconfig indenting]
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

asm-m32r/uaccess.h must #include <asm/setup.h>

This patch fixes the following compile error caused by
commit 4016a1390d07f15b267eecb20e76a48fd5c524ef
(mm/nommu.c: return 0 from kobjsize with invalid objects):

/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c: In function 'kobjsize':
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c:112: error: 'memory_end' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c:112: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/nommu.c:112: error: for each function it appears in.)

The patch also removes now no longer required memory_{start,end}
declarations inside access_ok().

Reported-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ext3: fix online resize bug

There is a bug when we are trying to verify that the reserve inode's
double indirect blocks point back to the primary gdt blocks.  The fix is
obvious, we need to mod the gdb count by the addr's per block.  You can
verify this with the following test case

dd if=/dev/zero of=disk1 seek=1024 count=1 bs=100M
losetup /dev/loop1 disk1
pvcreate /dev/loop1
vgcreate loopvg1 /dev/loop1
lvcreate -l 100%VG loopvg1 -n looplv1
mkfs.ext3 -J size=64 -b 1024 /dev/loopvg1/looplv1
mount /dev/loopvg1/looplv1 /mnt/loop
dd if=/dev/zero of=disk2 seek=1024 count=1 bs=50M
losetup /dev/loop2 disk2
pvcreate /dev/loop2
vgextend loopvg1 /dev/loop2
lvextend -l 100%VG /dev/loopvg1/looplv1
resize2fs /dev/loopvg1/looplv1

without this patch the resize2fs fails, with it the resize2fs succeeds.

Signed-off-by: Josef Bacik <jbacik@redhat.com>
Acked-by: Andreas Dilger <adilger@sun.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

nommu: fix ksize() abuse

The nommu binfmt code uses ksize() for pointers returned from do_mmap()
which is wrong.  This converts the call-sites to use the nommu specific
kobjsize() function which works as expected.

Cc: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@selenic.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

doc: document the kernel-doc conventions for kernel hackers

Provide documentation of the kernel-doc documentation conventions oriented
to kernel hackers.

Since I figure that there will be more people reading this
kernel-doc-nano-HOWTO.txt file who are kernel developers focused on the
rest of the kernel, than there will be readers of this file who are
documentation developers extracting that embedded kernel-doc
documentation, I have taken the liberty of making the new section added
here:

  How to format kernel-doc comments

the first section of the kernel-doc-nano-HOWTO.txt file.

This first section is intended to introduce, motivate and provide basic
usage of the kernel-doc mechanism for kernel hackers developing other
portions of the kernel.

Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbdev: export symbol fb_mode_option

Frame buffer and mode setting drivers can be built as modules,
so fb_mode_option needs to be exported to support these.

Prevents this error:

  ERROR: "fb_mode_option" [drivers/ps3/ps3av_mod.ko] undefined!

Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: reiserfs entry is out of date

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Edward Shishkin <edward.shishkin@gmail.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

v850: fix typo in header guard

Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

h8300: fix typo in header guard

Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_serial: filter out FP during baud rate detection

I made a change to u-boot that used the FP (Fractional Part) field of BRGR
to achieve more accurate baud rate generation.  Unfortunately, the
atmel_serial driver looks at the whole BRGR register when trying to detect
the baud rate that the port is currently running at, so setting FP to a
nonzero value breaks the baud rate detection.

I'll sit on the u-boot patch for a while longer, but this is clearly a
bug in the atmel_serial driver which should be fixed.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vt: fix vc_resize locking

Lockdep says we can't take tasklist lock or sighand lock inside ctrl_lock.

Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: only output msgmni value at boot time

When posting:
[PATCH 1/8] Scaling msgmni to the amount of lowmem
(see http://lkml.org/lkml/2008/2/11/171), I have added a KERN_INFO message
that is output each time msgmni is recomputed.

In http://lkml.org/lkml/2008/4/29/575 Tony Luck complained that this
message references an ipc namespace address that is useless.

I first thought of using an audit_log instead of a printk, as suggested by
Serge Hallyn.  But unfortunately, we do not have any other information
than the namespace address to provide here too.  So I chose to move the
message and output it only at boot time, removing the reference to the
namespace.

Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Pierre Peiffer <peifferp@gmail.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipc: restore MSGPOOL original value

When posting:

[PATCH 1/8] Scaling msgmni to the amount of lowmem

(see http://article.gmane.org/gmane.linux.kernel/637849/) I changed the
MSGPOOL value to make it fit what is said in the man pages (i.e.  a size
in bytes).

But Michael Kerrisk rightly complained that this change could affect the
ABI.  So I'm posting this patch to make MSGPOOL expressed back in Kbytes.
Michael, on his side, has fixed the man page.

Signed-off-by: Nadia Derbey <Nadia.Derbey@bull.net>
Cc: Pierre Peiffer <peifferp@gmail.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vt: fix background color on line feed, DEC invert

Original report: """I used to force my console to black-on-white by the
command `setterm -inversescreen on`.  In 2.6.26-rc4, I get lots of black
background characters."""

Another addendum to commit c9e587ab.  This was previously missed out since
I was not aware of what vc_decscnm was for.

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Reported-by: <thunder7@xs4all.nl>
Tested-by: <thunder7@xs4all.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cpufreq: fix null object access on Transmeta CPU

If cpu specific cpufreq driver(i.e.  longrun) has "setpolicy" function,
governor object isn't set into cpufreq_policy object at "__cpufreq_set_policy"
function in driver/cpufreq/cpufreq.c .

This causes a null object access at "store_scaling_setspeed" and
"show_scaling_setspeed" function in driver/cpufreq/cpufreq.c when reading or
writing through /sys interface (ex.  cat
/sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed)

Addresses:
http://bugzilla.kernel.org/show_bug.cgi?id=10654
https://bugzilla.redhat.com/show_bug.cgi?id=443354

Signed-off-by: CHIKAMA Masaki <masaki.chikama@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fbcon: fix wrong vmode bits copied on console switch

The interlaced and double line mode bits should not be copied to new
console when the console is switched.  Otherwise, the new console may be
set to incorrect refresh rate.

Also, the x and y offsets does not need to be copied.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

keys: remove unused key_alloc_sem

This semaphore doesn't appear to be used, so remove it.

Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cpusets: fix bug when adding nonexistent cpu or mem

Adding a nonexistent cpu to a cpuset will be omitted quietly.  It should
return -EINVAL.

Example: (real_nr_cpus <= 4 < NR_CPUS or cpu#4 was just offline)

# cat cpus
0-1
# /bin/echo 4 > cpus
# /bin/echo $?
0
# cat cpus

#

The same occurs when add a nonexistent mem.
This patch will fix this bug.
And when *buf == "", the check is unneeded.

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: Paul Jackson <pj@sgi.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pagemap: fix bug in add_to_pagemap, require aligned-length reads of /proc/pid/pagemap

Fix a bug in add_to_pagemap.  Previously, since pm->out was a char *,
put_user was only copying 1 byte of every PFN, resulting in the top 7
bytes of each PFN not being copied.  By requiring that reads be a multiple
of 8 bytes, I can make pm->out and pm->end u64*s instead of char*s, which
makes put_user work properly, and also simplifies the logic in
add_to_pagemap a bit.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thomas Tuttle <ttuttle@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

devscgroup: make white list more compact in some cases

Consider you added a 'c foo:bar r' permission to some cgroup and then (a
bit later) 'c'foo:bar w' for it.  After this you'll see the

c foo:bar r
c foo:bar w

lines in a devices.list file.

Another example - consider you added 10 'c foo:bar r' permissions to some
cgroup (e.g.  by mistake).  After this you'll see 10 c foo:bar r lines in
a list file.

This is weird.  This situation also has one more annoying consequence.
Having many items in a white list makes permissions checking slower, sine
it has to walk a longer list.

The proposal is to merge permissions for items, that correspond to the
same device.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

devscgroup: check for device permissions at mount time

Currently even if a task sits in an all-denied cgroup it can still mount
any block device in any mode it wants.

Put a proper check in do_open for block device to prevent this.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Tested-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

devscgroup: relax task to dev_cgroup conversion

Two functions, that need to get a device_cgroup from a task (they are
devcgroup_inode_permission and devcgroup_inode_mknod) make it in a strange
way:

They get a css_set from task, then a subsys_state from css_set, then a
cgroup from the state and then a subsys_state again from the cgroup.
Besides, the devices_subsys_id is read from memory, whilst there's a
enum-ed constant for it.

Optimize this part a bit:
1. Get the subsys_stats form the task and be done - no 2 extra
   dereferences,
2. Use the device_subsys_id constant, not the value from memory
   (i.e. one less dereference).

Found while preparing 2.6.26 OpenVZ port.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

devcgroup: make a helper to convert cgroup_subsys_state to devs_cgroup

This is just picking the container_of out of cgroup_to_devcgroup into a
separate function.

This new css_to_devcgroup will be used in the 2nd patch.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

introduce memory_read_from_buffer()

This patch introduces memory_read_from_buffer().

The only difference between memory_read_from_buffer() and
simple_read_from_buffer() is which address space the function copies to.

simple_read_from_buffer copies to user space memory.
memory_read_from_buffer copies to normal memory.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Doug Warzecha <Douglas_Warzecha@dell.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Abhay Salunke <Abhay_Salunke@dell.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Markus Rechberger <markus.rechberger@amd.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Bob Moore <robert.moore@intel.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Len Brown <lenb@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Brian King <brking@us.ibm.com>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib: export bitrev16

Bluetooth will be able to use this.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-ds1374: rename device to just "ds1374"

Change the name of the device from "rtc-ds1374" to just "ds1374", to match
what all other RTC drivers do.  I seem to remember that this name was
chosen to avoid possible confusion with an older ds1374 driver, but that
driver was removed 3 months ago.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix various old email addresses for dwmw2

Although if people have questions about ARCnet, perhaps it's _better_
for them to be mailing dwmw2@cam.ac.uk about it...

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: PATH_MAX needs limits.h

Include limits.h to get a definition of PATH_MAX.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: stub needs to tolerate SIGWINCH

We lost the marking of SIGWINCH as being OK to receive during stub
execution, causing a panic should that happen.

Cc: Benedict Verheyen <benedict.verheyen@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: memcpy export needs to follow host declaration

x86_64 defines either memcpy or __memcpy depending on the gcc version, and
it looks like UML needs to follow that in its exporting.

Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: deal with inaccessible address space start

This patch makes os_get_task_size locate the bottom of the address space,
as well as the top.  This is for systems which put a lower limit on mmap
addresses.  It works by manually scanning pages from zero onwards until a
valid page is found.

Because the bottom of the address space may not be zero, it's not
sufficient to assume the top of the address space is the size of the
address space.  The size is the difference between the top address and
bottom address.

[jdike@addtoit.com: changed the name to reflect that this function is
supposed to return the top of the process address space, not its size and
changed the return value to reflect that.  Also some minor formatting
changes]
Signed-off-by: Tom Spink <tspink@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

uml: remove a duplicate include

Removed duplicated include file "kern_util.h" in
arch/um/drivers/ubd_kern.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>