Olof Johansson [Mon, 26 Oct 2015 05:42:37 +0000 (14:42 +0900)] 
Merge tag 'sunxi-clocks-for-4.4' of https://git./linux/kernel/git/mripard/linux into next/dt
Bringing in the sunxi clock branch since it introduces header file contents
that is needed by the DT branch. This is a stable tag shared with the clk tree.
Allwinner clock additions for 4.4
- Support for the Audio PLL and child clocks
- Support for the A33 AHB gates
- New clk-multiplier generic driver
* tag 'sunxi-clocks-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi: mod1 clock support
clk: sunxi: codec clock support
clk: sunxi: pll2: Add A13 support
clk: sunxi: Add a driver for the PLL2
clk: Add a basic multiplier clock
clk: sunxi: Add A33 gates support
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 26 Oct 2015 05:27:33 +0000 (14:27 +0900)]
Merge tag 'arm/soc/for-4.4/rpi-dt-v2' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains the DT changes for BCM2835 in 4.4. It
pulls in clk/clk-bcm2835 (which Stephen Boyd has said would be stable)
because the DT changes to enable the clock driver need the driver
itself to be present. These changes include the following:
- Eric Anholt, moves the bcm2835 clock driver under bcm/ where it belongs with
other Broadcom clock providers drivers, defines the binding for new clock
driver, adds support for programming the BCM2835 audio domain, adds the DDC I2C
controller to Device Tree, and finally migrates the Device Tree to use the new
clock driver binding
- Lubomir Rintel adds support for the Raspberry Pi Model A+ and B revision 2, and
remove the I2S controller which is non-existent on Raspberry Pi Model B
- Stefan Wahren adds an uart0 label for referencing the UART adapter
* tag 'arm/soc/for-4.4/rpi-dt-v2' of https://github.com/Broadcom/stblinux:
ARM: bcm2835: Add the DDC I2C controller to the device tree.
ARM: bcm2835: Switch to using the new clock driver support.
ARM: bcm2835: dt: Add Raspberry Pi Model A+
ARM: bcm2835: dt: Add Raspberry Pi Model B rev2
ARM: bcm2835: dt: Raspberry Pi Model B had no I2S
ARM: bcm2835: add label for uart0
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
Signed-off-by: Olof Johansson <olof@lixom.net>
Masahiro Yamada [Sat, 24 Oct 2015 03:25:31 +0000 (12:25 +0900)] 
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
Add aliases to fix the I2C indexes like the other UniPhier boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 26 Oct 2015 01:13:50 +0000 (10:13 +0900)]
Merge tag 'samsung-dt-2' of git://git./linux/kernel/git/kgene/linux-samsung into next/dt
Samsung 2nd DT updates for v4.4
- use exynos5420-dw-mshc instead of exynos5250 for exynos3250
- add DISP1 clocks and the DISP1 power domain of two closk
on exynos5250 (clock commit got Stephen's ack)
- add vbus regulators on exynos3250, exynos4210 and exynos4412 boards
- fix typo in regulator enable GPIO property on s5pv20-aquila and goni
- document: correct the example of exynos power domain clocks
- document: consolidate exynos SoC dt-bindings and non-Samsung
boards related compatibles (FriendlyARM, Google, Hardkernel
and Insignal)
- update MAINTAINER entries accordingly (documentation)
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
MAINTAINERS: Add documentation and dt-bindings for exynos stuff
dt-bindings: EXYNOS: Document compatibles from other vendors
dt-bindings: Consolidate Exynos SoC bindings
ARM: dts: Add clocks to DISP1 domain in exynos5250
dt-bindings: Correct the example for Exynos power domain clocks
ARM: dts: Fix typo in regulator enable GPIO property in s5pv210-goni
ARM: dts: Fix typo in regulator enable GPIO property in s5pv210-aquila
ARM: dts: Add vbus regulator to USB2 phy nodes on exynos3250, exynos4210 and exynos4412 boards
clk: samsung: exynos5250: Add DISP1 clocks
ARM: dts: use exynos5420-dw-mshc compatible for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Mon, 26 Oct 2015 00:53:14 +0000 (09:53 +0900)]
Merge tag 'tegra-for-4.4-dt' of git://git./linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Devicetree changes for v4.4-rc1
Mostly a bunch of updates to the Toradex Apalis and Colibri platforms
along with a couple of cleanup patches.
* tag 'tegra-for-4.4-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (25 commits)
ARM: tegra: Use consistent indentation for SATA node
ARM: tegra: colibri-eval: Fix power/wakeup key
ARM: tegra: colibri-eval: Add comment concerning SD/MMC
ARM: tegra: colibri-eval: Fix vendor string of M41T0M6 RTC
ARM: tegra: colibri: Properly align pin names
ARM: tegra: colibri: Replace eMMC label by comment
ARM: tegra: colibri: Activate STMPE811 touch controller
ARM: tegra: colibri: Add touch pen interrupt pin muxing
ARM: tegra: colibri: Fix comment about 3v3 fixed supply
ARM: tegra: colibri: Add pin muxing for on-module power I2C
ARM: tegra: colibri: Improve comment about thermal alert pin
ARM: tegra: colibri: Fix HDMI supplies
ARM: tegra: colibri: Update hardware revisions compatibility
ARM: tegra: apalis-eval: Fix power/wakeup key
ARM: tegra: apalis-eval: Fix backlight PWM comment
ARM: tegra: apalis-eval: Set OTG dr_mode
ARM: tegra: apalis-eval: Enable HDA controller
ARM: tegra: apalis: Properly align pin names
ARM: tegra: apalis: Add digital audio pin muxing
ARM: tegra: apalis: Add comment concerning eMMC
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Bhupesh Sharma [Fri, 23 Oct 2015 19:32:01 +0000 (01:02 +0530)] 
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
This patch adds build support for LS2080a QDS & RDB board DTS files
in the arm64 DTS Makefile.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:32:00 +0000 (01:02 +0530)]
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
This patch adds the LS2080a DTS files for QDS and RDB boards
which support the LS2080a SoC.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:58 +0000 (01:01 +0530)]
dts/ls2080a: Update Simulator DTS to add support of various peripherals
This patch updates the LS2080a simulator DTS to add support of various
peripherals which are supported on the simulator platform and explicitly
disables those which are yet not supported on the platform.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:59 +0000 (01:01 +0530)]
dts/ls2080a: Remove text about writing to Free Software Foundation
Checkpatch complains about the text suggesting writing to
Free Software Foundation for GPLv2 license copy.
This patch removes the same from the .dtsi and .dts
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:57 +0000 (01:01 +0530)]
dts/ls2080a: Update DTSI to add support of various peripherals
This patch updates the LS2080a DTSI (DTS Include) file to add
support for the following peripherals:
- USB 3.0 Host
- PMU
- CCN-504
- SATA
- SPI
- PCIe
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:56 +0000 (01:01 +0530)]
doc: DTS: Update DWC3 binding to provide reference to generic bindings
Since the Synopsys DWC3 controller driver inherits the generic bindings
defined in 'usb/generic.txt', this patch tries to capture the same in
the DWC3 binging documentation to avoid any confusion in usage of properties
like 'dr_mode' for certain SoCs like FSL LS2080A.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:55 +0000 (01:01 +0530)]
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Update the FSL, GPIO binding documentation to add support
for GPIO controller found on Freescale's LS2080A platform.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:53 +0000 (01:01 +0530)]
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Since the same board components can be used across ARM and PPC board families,
this patch moves the FSL board-specific bindings out of bindings/powerpci.
While at it, this patch also adds the bindings for QIXIS FPGA controller
found on FSL LS2080A boards. These boards have an on-board FPGA/CPLD
connected to the IFC controller.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:52 +0000 (01:01 +0530)]
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
This patch adds a devicetree binding documentation for Freescale's
LS2080A QDS and RDB boards.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:51 +0000 (01:01 +0530)]
arm64: Rename FSL LS2085A SoC support code to LS2080A
Freescale is renaming the LS2085A SoC to LS2080A. This patch
addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bhupesh Sharma [Fri, 23 Oct 2015 19:31:50 +0000 (01:01 +0530)]
arm64: Use generic Layerscape SoC family naming
Freescale will be a spinning-out a set of ARMv8 based SoCs which
will be based on a similar overall SoC architecture. So, this patch
converts the existing infrastructure in the arm64/dts, arm64/Kconfig
and arm64/configs to use the generic convention ARCH_LAYERSCAPE
in place of the more specific FSL_LS2085A, to save code duplication
later-on.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 23 Oct 2015 20:20:53 +0000 (22:20 +0200)] 
Merge tag 'at91-ab-dt2' of git://git./linux/kernel/git/abelloni/linux into next/dt
Merge "Second batch of DT changes for 4.4" from Alexandre Belloni:
- some DT fixes: pullups, disabled property
- the PMC is now a syscon
- great improvement of sama5d2 support
* tag 'at91-ab-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91/dt: sama5d2: add missing devices
ARM: at91/dt: sama5d4: add the macb1 node
ARM: at91/dt: add pullup on mmc2 data signals
ARM: at91/dt: sama5d2_xplained: add regulator nodes
ARM: at91/dt: fix "disabled" property on at91rm9200
ARM: at91/dt: use syscon for PMC
Arnd Bergmann [Fri, 23 Oct 2015 20:17:19 +0000 (22:17 +0200)]
Merge tag 'omap-for-v4.4/dt-pt2' of git://git./linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.4 merge window, part 2" from Tony Lindgren:
Few more omap dts changes for v4.4 merge window, mostly to fix and clean
up some omap5 issues to allow adding other omap5 boards. Also some other
fixes and clean-up:
- Fix SDIO WLAN for omap5 that's been broken for a while. As further
patches are still needed for wl18xx, no need for stable on this one.
- Move most of omap5 support into omap5-board-common.dtsi as most omap5
boards seem to share the same basic set of devices.
- Add minimal IGEPv5 support using based on omap5-board-common.dtsi
- Remove now unneedes gpio hogging for dra72-evm
- Update Javier Martinez Canillas email address
- Change earlier IGEP boards to use IOPAD pinmux macros
* tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-base0033: Use IOPAD pinmux macro
ARM: dts: am335x-igep0033: Use IOPAD pinmux macro
ARM: dts: omap3-igep0020: Use IOPAD pinmux macro
ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts
ARM: dts: Update Javier Martinez Canillas's email
ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios
ARM: dts: Add basic support for isee igepv5
ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi
ARM: dts: Fix WLAN regression on omap5-uevm
Masahiro Yamada [Wed, 21 Oct 2015 11:36:30 +0000 (20:36 +0900)]
ARM: dts: uniphier: add ProXstream2 Vodka board support
Initial version of DTS for ProXstream2 Vodka board.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Masahiro Yamada [Wed, 21 Oct 2015 11:36:29 +0000 (20:36 +0900)]
ARM: dts: uniphier: add ProXstream2 Gentil board support
Initial version of DTS for ProXstream2 Gentil board.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Masahiro Yamada [Wed, 21 Oct 2015 11:36:27 +0000 (20:36 +0900)]
ARM: dts: uniphier: use stdout-path instead of console
Specifying both console and stdout-path is redundant. Add options
":115200n8" to stdout-path and drop "console=ttyS0,115200".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Krzysztof Kozlowski [Fri, 23 Oct 2015 20:07:19 +0000 (05:07 +0900)] 
MAINTAINERS: Add documentation and dt-bindings for exynos stuff
Extend the Samsung Exynos maintainer entry to match SoC documentation
and SoC dt-bindings directories. Without that some files, like
bindings/arm/samsung/pmu.txt, are not matched by existing patterns.
This also may serve as a hint where new documentation and bindings
(not matching specific subsystem) should be put.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Krzysztof Kozlowski [Fri, 23 Oct 2015 20:07:06 +0000 (05:07 +0900)]
dt-bindings: EXYNOS: Document compatibles from other vendors
Document compatibles used on other Exynos-based boards (non-Samsung):
FriendlyARM, Google, Hardkernel and Insignal.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Hakjoo Kim <ruppi.kim@hardkernel.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Krzysztof Kozlowski [Fri, 23 Oct 2015 20:07:02 +0000 (05:07 +0900)]
dt-bindings: Consolidate Exynos SoC bindings
Exynos SoC Device Tree bindings are spread over arm/exynos/ and
arm/samsung/ directories. There is no need for that separation and it
actually confuses. Put power domain bindings under power/ and
remaining samsung-boards.txt under arm/samsung/.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Arnd Bergmann [Fri, 23 Oct 2015 20:04:49 +0000 (22:04 +0200)]
Merge tag 'sti-dt-for-v4.4-2' of https://git./linux/kernel/git/mcoquelin/sti into next/dt
Merge "STi DT changes for v4.4, round 2" from Maxime Coquelin:
- Use STiH418's A9 PLL
- Add Ethernet support to STiH407 family
* tag 'sti-dt-for-v4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
ARM: STi: DT: Add support for stih418 A9 pll
ARM: dts: Enable Ethernet on STi's B2199 board
ARM: dts: Enable Ethernet on STi's B2120 boards
ARM: dts: Add Ethernet node to STiH407 family
ARM: dts: Fix RGMII pinctrl timings
Vladimir Zapolskiy [Fri, 25 Sep 2015 17:35:34 +0000 (20:35 +0300)] 
ARM: dts: WM8750: fix cpu compatible value
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Vladimir Zapolskiy [Fri, 25 Sep 2015 17:35:33 +0000 (20:35 +0300)]
ARM: dts: TI-Nspire: fix cpu compatible value
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tomeu Vizoso [Thu, 15 Oct 2015 10:31:24 +0000 (12:31 +0200)] 
ARM: dts: Add clocks to DISP1 domain in exynos5250
Adds to the node of the DISP1 power domain the two clocks that need to
be reparented while the domain is powered off:
CLK_MOUT_ACLK200_DISP1_SUB and CLK_MOUT_ACLK300_DISP1_SUB.
Otherwise the state is unknown at power up and the mixer's clocks are
all messed up.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Link: http://lkml.kernel.org/g/561CDC33.7050103@collabora.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Krzysztof Kozlowski [Wed, 14 Oct 2015 05:58:45 +0000 (14:58 +0900)]
dt-bindings: Correct the example for Exynos power domain clocks
Since commit
29e5eea06bc1 ("ARM: EXYNOS: Get current parent clock for
power domain on/off") the "pclkN" names of "clock-names" property is not
parsed any more. The bindings and driver were updated but the example
was not. Fix the example now.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Laurent Pinchart [Mon, 12 Oct 2015 21:12:35 +0000 (00:12 +0300)] 
ARM: dts: Fix typo in regulator enable GPIO property in s5pv210-goni
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Laurent Pinchart [Mon, 12 Oct 2015 21:12:34 +0000 (00:12 +0300)]
ARM: dts: Fix typo in regulator enable GPIO property in s5pv210-aquila
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Marek Szyprowski [Fri, 21 Aug 2015 12:38:38 +0000 (14:38 +0200)] 
ARM: dts: Add vbus regulator to USB2 phy nodes on exynos3250, exynos4210 and exynos4412 boards
Exynos USB2 PHY driver now supports VBUS regulator, so add it to all
boards which have it available. This also fixes commit
7eec1266751b ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2"),
which added new regulators to Trats2 board, but without linking them to
the consumers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 7eec1266751b ("ARM: dts: Add Maxim 77693 PMIC to exynos4412-trats2")
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Tomeu Vizoso [Thu, 15 Oct 2015 10:31:23 +0000 (12:31 +0200)]
clk: samsung: exynos5250: Add DISP1 clocks
When the DISP1 power domain is powered off, there's two clocks that need
to be temporarily reparented to OSC, and back to their original parents
when the domain is powered on again.
We expose these two clocks in the DT bindings so that the DT node of the
power domain can reference them.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Jaehoon Chung [Fri, 23 Oct 2015 18:42:02 +0000 (03:42 +0900)] 
ARM: dts: use exynos5420-dw-mshc compatible for exynos3250
There are some differences of mobile storage host between exynos3250
and exnos5250. For example, exynos3250 supports the HS400 mode, but
exynos5250 doesn't support it.
Since exynos3250 can perform the similar function with exynos5420
compatible, this patch changes the compatible from exynos5250 to
exynos5420 for mshc.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Olof Johansson [Fri, 23 Oct 2015 17:51:21 +0000 (10:51 -0700)]
Merge tag 'imx-dt-4.4' of git://git./linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.4:
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
* tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: ls1021a: Add quirk for Erratum
A009116
ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property
ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"
ARM: dts: imx6: change the core clock of spdif
ARM: dts: vf-colibri: enable NAND flash controller
ARM: dts: vf610twr: add NAND flash controller peripherial
ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board
ARM: dts: imx: add Boundary Devices Nitrogen6_Max board
ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices
ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices
of: Add Boundary Devices Inc. vendor prefix
ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support
ARM: dts: imx6dql-nitrogen6x: add touchscreen support
ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel
ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel
ARM: dts: vf500-colibri: Add device tree node for touchscreen support
ARM: dts: i.MX35: fix cpu compatible value
ARM: dts: i.MX31: fix cpu compatible value
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Oct 2015 17:24:44 +0000 (10:24 -0700)]
Merge tag 'v4.3-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Delete regulator-compatible usage in mt8135-evbp1.dts.
The regualtor-compatible binding is deprecated, instead the node name
is used.
Mediatek timer driver supports as well mt8127, mt8135 and mt8173. Add
these SOCs to the bindings list.
Power domains venc and venc_lt need clocks two extra clocks to access
their registers. We update the bindings documentation about this.
Update SMP bindings documentation by adding support for mt6589 and mt81xx SOCs.
Update mt8127.dtsi and mt8135.dtsi to enable SMP support.
* tag 'v4.3-next-dts' of https://github.com/mbgg/linux-mediatek:
ARM: dts: mt8127: enable basic SMP bringup for mt8127
ARM: dts: mt8135: enable basic SMP bringup for mt8135
devicetree: bindings: add new SMP enable method Mediatek SoC
dt-bindings: soc: Add clocks for Mediatek SCPSYS unit
dt-bindings: add more MediaTek SoC to mtk-timer binding
ARM: dts: mt8135-evbp1: remove regulator-compatible usage
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Oct 2015 17:19:04 +0000 (10:19 -0700)]
Merge tag 'v4.4-rockchip-dts32-2' of git://git./linux/kernel/git/mmind/linux-rockchip into next/dt
SPDIF device nodes for the newly added driver.
* tag 'v4.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock2 Square
ARM: dts: rockchip: Add SPDIF transceiver for RK3288
ARM: dts: rockchip: Add SPDIF optical out on Radxa Rock
ARM: dts: rockchip: Add SPDIF transceiver for RK3188
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 23 Oct 2015 17:17:27 +0000 (10:17 -0700)]
Merge tag 'sunxi-dt-for-4.4-2' of https://git./linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.4, round 2
More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi
M2, pcduino2), further consolidation for the q8-based designs and a bunch
of random patches enhancing support for existing boards
* tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (27 commits)
ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board
ARM: dts: sun6i: Add mmc2_pins_a pinmux setting to sun6i-a31.dtsi
ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80
ARM: dts: sun8i: Add NMI interrupt controller node
ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus"
ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulators
ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator names
ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano
ARM: dts: sun6i: Turn on gmac on Colombus
ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts file
ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi
ARM: dts: sunxi: Enable PWM controller on Q8 format tablets
ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s
ARM: dts: sun5i: Add PWM controller node for A13 / A10s
ARM: sun5i: Add C.H.I.P DTS
ARM: dts: sunxi: Add dtsi for AXP22x PMIC
ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano
ARM: sun5i: dt: Add UART3 CTS and RTS pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Eric Anholt [Fri, 9 Oct 2015 21:27:47 +0000 (14:27 -0700)] 
ARM: bcm2835: Add the DDC I2C controller to the device tree.
We need to use it for getting video modes over HDMI.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Eric Anholt [Mon, 28 Sep 2015 21:22:05 +0000 (14:22 -0700)]
ARM: bcm2835: Switch to using the new clock driver support.
This will give us the ability to set the pixel and HDMI state machine
clocks for the VC4 KMS driver, change the CPU frequency, and
potentially gate clocks in the future (once we also write a power
domain driver). It also gives the uart an explicit clock reference,
so that we don't need to change the physical addresses of the old
fixed clk_bcm2835.c clocks for Raspberry Pi 2 port.
Two clocks get their frequencies updated as a result of this. One is
uart's apb_pclk, which was previously accidentally grabbing the fixed
uart0_pclk due to the apb_pclk not having clk_register_clkdev()
called. The uart doesn't seem to do anything with apb_pclk other than
make sure it's on, so that appears safe (also, as far as I can see,
the apb clock is actually the same as the VPU clock). The other is
EMMC, which according to the docs was supposed to be in the 50-100Mhz
range, but it turns out the firmware needed to change to running it at
the 250Mhz core clock speed to avoid a bug in clock domain crossing.
Additionally, anything using BCM2835_CLOCK_VPU will now have a correct
clock rate if the user configures the boot-time core clock speed using
config.txt.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Eric Anholt [Wed, 14 Oct 2015 22:37:10 +0000 (15:37 -0700)]
Merge remote-tracking branch 'clk/clk-bcm2835' into bcm2835-dt-next
The DT changes for enabling the clock driver on 2835 require that the
clock driver be present. Stephen Boyd has said that these commits
would be stable for merging.
Signed-off-by: Eric Anholt <eric@anholt.net>
Olof Johansson [Thu, 22 Oct 2015 17:43:03 +0000 (10:43 -0700)]
Merge tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.4 (part 2)
- Add support for severals Armada-370-based Seagate NAS
- Fix Ready NAS device tree
- Modify SDHCI binding for A388-GP allowing using it on old and new
version of the board
* tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: set SW polling as SDHCI card detection on A388-GP
arm: mvebu: reorder nodes under internal-regs by address in RN2120 .dts file
arm: mvebu: disable unused Armada RTC on ReadyNAS 102, 104 and 2120
ARM: mvebu: add DT support for Seagate Personal Cloud
ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 22 Oct 2015 17:08:46 +0000 (10:08 -0700)]
Merge tag 'socfpga_for_v4.4_cleanup' of git://git./linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA dts cleanup for v4.4
- Re-order DTS nodes into correct alphabetical order
* tag 'socfpga_for_v4.4_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: sort nodes alphabetically
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Thu, 22 Oct 2015 17:07:04 +0000 (10:07 -0700)]
Merge tag 'socfpga_dts_for_v4.4_part_2' of git://git./linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS update for v4.4, part 2
- Add the FPGA manager node
* tag 'socfpga_dts_for_v4.4_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: add fpga manager
Signed-off-by: Olof Johansson <olof@lixom.net>
Emilio López [Fri, 18 Jul 2014 18:28:02 +0000 (15:28 -0300)] 
clk: sunxi: mod1 clock support
The module 1 type of clocks consist of a gate and a mux and are used on
the audio blocks to mux and gate the PLL2 outputs for AC97, IIS or
SPDIF. This commit adds support for them on the sunxi clock driver.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Emilio López [Fri, 18 Jul 2014 18:49:37 +0000 (15:49 -0300)]
clk: sunxi: codec clock support
The codec clock on sun4i, sun5i and sun7i is a simple gate with PLL2 as
parent. Add a driver for such a clock.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Mon, 21 Sep 2015 11:32:43 +0000 (13:32 +0200)] 
clk: sunxi: pll2: Add A13 support
The A13, unlike the A10 and A20, doesn't use a pass-through exception for
the 0 value in the pre and post dividers, but increments all the values
written in the register by one.
Add an exception for both these cases to handle them nicely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Fri, 18 Jul 2014 18:48:35 +0000 (15:48 -0300)]
clk: sunxi: Add a driver for the PLL2
The PLL2 on the A10 and later SoCs is the clock used for all the audio
related operations.
This clock has a somewhat complex output tree, with three outputs (2X, 4X
and 8X) with a fixed divider from the base clock, and an output (1X) with a
post divider.
However, we can simplify things since the 1X divider can be fixed, and we
end up by having a base clock not exposed to any device (or at least
directly, since the 4X output doesn't have any divider), and 4 fixed
divider clocks that will be exposed.
This clock seems to have been introduced, at least in this form, in the
revision B of the A10, but we don't have any information on the clock used
on the revision A.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Maxime Ripard [Tue, 19 May 2015 20:19:33 +0000 (22:19 +0200)]
clk: Add a basic multiplier clock
Some clocks are using a multiplier component, however, unlike their mux,
gate or divider counterpart, these factors don't have a basic clock
implementation.
This leads to code duplication across platforms that want to use that kind
of clocks, and the impossibility to use the composite clocks with such a
clock without defining your own rate operations.
Create such a driver in order to remove these issues, and hopefully factor
the implementations, reducing code size across platforms and consolidating
the various implementations.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Javier Martinez Canillas [Mon, 19 Oct 2015 15:34:21 +0000 (17:34 +0200)] 
ARM: dts: am335x-base0033: Use IOPAD pinmux macro
Use the AM33XX pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Oct 2015 15:34:20 +0000 (17:34 +0200)]
ARM: dts: am335x-igep0033: Use IOPAD pinmux macro
Use the AM33xx pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Mon, 19 Oct 2015 15:34:19 +0000 (17:34 +0200)]
ARM: dts: omap3-igep0020: Use IOPAD pinmux macro
Use the OMAP3 pinmux IOPAD macro to define the physical address instead
of the offset from the padconf address. It makes the DTS easier to read
since matches the addresses listed in the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Vignesh R [Wed, 14 Oct 2015 13:54:25 +0000 (19:24 +0530)] 
ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts
On am437x-gp-evm, pixcir_i2c_ts can wakeup the system from low power
state via pinctrl and IO daisy chain using generic wakeirq framework.
With commit
3fffd1283927 ("i2c: allow specifying separate wakeup
interrupt in device tree") i2c core allows optional wakeirq to be
specified via device tree. Add wakeup irq entry to enable pixcir_i2c_ts
to wake the system from low power state.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Javier Martinez Canillas [Wed, 14 Oct 2015 10:00:30 +0000 (12:00 +0200)]
ARM: dts: Update Javier Martinez Canillas's email
I see that people are still sending emails to my old address (that no
longer exists) since is the one mentioned in the IGEP DTS. Replace it
with my current email address to avoid this.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mugunthan V N [Mon, 21 Sep 2015 14:53:51 +0000 (20:23 +0530)] 
ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios
With the current implementation of GPIO hogging and with
gpio-pcf857x is built as module, ethernet doesn't work on boot
and doesn't throw any error/warning to user. Ethernet becomes
operational when inserting gpio-pcf857x module, even this time
there is no error/warning logs to user that ethernet is
operational.
When using with NFS rootfs and gpio-pcf857x as module, board
doesn't boot as it doesn't get any ip address and doesn't throw
any error/warning. To over come this, now cpsw driver tries to
get mode-gpios. When gpio-pcf857x is built as module it will
throw error, so that user can decide either to built in
gpio-pcf857x to continue with nfs boot or choose alternate rootfs
filesystem like sd/ramdisk.
When using mmc/ramdisk as root fs, cpsw will probe defer and
re-probes again when gpio-pcf857x module is inserted and ethernet
becomes operational.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thierry Reding [Thu, 24 Sep 2015 08:00:05 +0000 (10:00 +0200)] 
ARM: tegra: Use consistent indentation for SATA node
The indentation for properties in the SATA device tree node on Tegra124
deviates from the rest of the device tree file. Restore consistency and
get rid of a couple of gratuitous blank lines while at it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ludovic Desroches [Fri, 16 Oct 2015 13:04:44 +0000 (15:04 +0200)] 
ARM: at91/dt: sama5d2: add missing devices
Big update of the sama5d2.dtsi file since many patches have reached te
mainline:
- add generated clocks
- enable crypto devices
- add flexcom devices
- add tdes device
- add sdmmc devices
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Gregory CLEMENT [Fri, 16 Oct 2015 12:21:34 +0000 (14:21 +0200)] 
ARM: at91/dt: sama5d4: add the macb1 node
The second macb is present on all the sama5d4 SoCs. Let's add a node
reflecting it in the device tree.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Sylvain Rochet [Mon, 7 Sep 2015 15:47:58 +0000 (17:47 +0200)] 
ARM: at91/dt: add pullup on mmc2 data signals
MMC data lines may be left floating if nothing is currently driving the
data lines, which is the case when mmc is in idle state, thus consuming
a useless extra amount of power. Add pullup on mmc2 data signals in the
same way it was previously done for mmc0 and mmc1.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Wenyou Yang [Wed, 14 Oct 2015 02:59:56 +0000 (10:59 +0800)] 
ARM: at91/dt: sama5d2_xplained: add regulator nodes
Add regulator nodes of PMIC ACT8945A chip on the board.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Michael Opdenacker [Tue, 13 Oct 2015 11:24:24 +0000 (13:24 +0200)] 
ARM: at91/dt: fix "disabled" property on at91rm9200
Fix instances of "disable" instead of "disabled"
in the at91rm9200 dtsi.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alexandre Belloni [Mon, 12 Oct 2015 14:28:38 +0000 (16:28 +0200)] 
ARM: at91/dt: use syscon for PMC
The PMC is not only used to drive the clocks but also has some registers
related to other functions. One of those is for example the USB gadget
bias.
Using a syscon allows to properly separate those functions.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Rajesh Bhagat [Wed, 14 Oct 2015 05:34:12 +0000 (11:04 +0530)] 
ARM: dts: ls1021a: Add quirk for Erratum
A009116
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum
A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Laurent Pinchart [Mon, 12 Oct 2015 21:12:33 +0000 (00:12 +0300)]
ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property
The property name should be "gpio", not "gpios". Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Opdenacker [Tue, 13 Oct 2015 11:43:55 +0000 (13:43 +0200)]
ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"
Fix a typo, replacing "pinctrl-name" by "pinctrl-names"
in the Phytec phyFLEX-i.MX6 Quad dtsi.
Also fix a typo in the board name
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shengjiu Wang [Sat, 10 Oct 2015 10:15:07 +0000 (18:15 +0800)] 
ARM: dts: imx6: change the core clock of spdif
The correct core clock of spdif is SPDIF_GCLK, which is added to
clock tree. So the dts also need to be updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 7 Oct 2015 23:58:36 +0000 (16:58 -0700)] 
ARM: dts: vf-colibri: enable NAND flash controller
Enable NAND access by adding pinmux and NAND flash controller node
to device tree. The NAND chips currently used on the Colibri VF61
requires 8-bit ECC per 512 byte page, hence specify 32-bit ECC
strength per 2k page size.
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Wed, 7 Oct 2015 23:58:35 +0000 (16:58 -0700)]
ARM: dts: vf610twr: add NAND flash controller peripherial
This adds the NAND flash controller (NFC) peripherial. The driver
supports the SLC NAND chips found on Freescale's Vybrid Tower System
Module. The Micron NAND chip on the module needs 4-bit ECC per 512
byte page. Use 24-bit ECC per 2k page, which is supported by the
driver.
Signed-off-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:46 +0000 (15:46 +0200)] 
ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board
Based on an i.MX6 Solo with 512MB DDR3.
http://boundarydevices.com/product/nitrogen6_lite/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:45 +0000 (15:46 +0200)]
ARM: dts: imx: add Boundary Devices Nitrogen6_Max board
Based on i.MX6 Quad with 4GB of DDR3.
http://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:44 +0000 (15:46 +0200)]
ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:43 +0000 (15:46 +0200)]
ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:42 +0000 (15:46 +0200)]
of: Add Boundary Devices Inc. vendor prefix
This patch adds the vendor prefix for Boundary Devices Inc. which is a
supplier of ARM-based single board computers and System-on-Modules for
the general embedded market.
Website: http://boundarydevices.com/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:41 +0000 (15:46 +0200)]
ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:40 +0000 (15:46 +0200)]
ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:39 +0000 (15:46 +0200)]
ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:46:38 +0000 (15:46 +0200)]
ARM: dts: imx6dql-nitrogen6x: add touchscreen support
This patch adds the different touchscreens that can be connected using
the displays available for this board.
http://boundarydevices.com/product-category/displays/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:05:20 +0000 (15:05 +0200)]
ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel
This patch adds support for the 7" LCD display available for Sabrelite:
http://boundarydevices.com/product/7-800x480-display/
Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Gary Bisson [Wed, 30 Sep 2015 13:05:19 +0000 (15:05 +0200)]
ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel
This patch adds support for the 7" LCD display available for Nitrogen6x:
http://boundarydevices.com/product/7-800x480-display/
Also add label to backlight_lcd and connect it to the panel.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Sanchayan Maity [Tue, 1 Sep 2015 12:36:53 +0000 (18:06 +0530)] 
ARM: dts: vf500-colibri: Add device tree node for touchscreen support
Add device tree node for touchscreen support on Colibri VF50. The
touchscreen functionality on VF50 uses the ADC channels of Vybrid
and some GPIOs. Also add pinctrl nodes for proper pinmux.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Zapolskiy [Fri, 25 Sep 2015 17:35:31 +0000 (20:35 +0300)]
ARM: dts: i.MX35: fix cpu compatible value
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Zapolskiy [Fri, 25 Sep 2015 17:35:30 +0000 (20:35 +0300)]
ARM: dts: i.MX31: fix cpu compatible value
The change corrects cpu compatible property to a defined one,
see Documentation/devicetree/bindings/arm/cpus.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adrian Alonso [Fri, 25 Sep 2015 21:05:57 +0000 (16:05 -0500)] 
ARM: dts: imx: imx7d add iomuxc lpsr device node
Add device tree node to support iomuxc-lpsr controller, fsl,input-sel
phandle allows to get input select register base address which is
shared from main iomuxc controller.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fugang Duan [Mon, 7 Sep 2015 02:55:02 +0000 (10:55 +0800)] 
ARM: dts: imx7d-sdb: add fec1 and fec2 support
Enable fec1 and fec2 for i.MX7d-sdb board.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adrian Alonso [Fri, 18 Sep 2015 16:29:52 +0000 (11:29 -0500)]
ARM: dts: imx7d-pinfunc: add gpio1 pad iomux settings
- Add imx7 SoC GPIO1 pad iomuxc settings
<mux_reg conf_reg input_reg mux_mode input_val>
- Fix UART input select daisy chain setting values
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Yuan Yao [Wed, 16 Sep 2015 08:20:43 +0000 (16:20 +0800)] 
ARM: dts: Add node for ina220 on LS1021ATWR
The INA220 monitors both shunt drop and supply voltage.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alison Wang [Mon, 14 Sep 2015 06:45:28 +0000 (14:45 +0800)] 
ARM: ls1021a: Add dma-coherent property for eTSEC nodes
This patch adds dma-coherent property for eTSEC nodes, so
coherent DMA operations are supported.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 8 Sep 2015 01:57:12 +0000 (22:57 -0300)] 
ARM: dts: imx7d-sdb: Add USB support
Add support for USBOTG1 and USBOTG2.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 8 Sep 2015 01:57:11 +0000 (22:57 -0300)]
ARM: dts: imx7d: Add USB support
Add USB OTG and Host support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fugang Duan [Mon, 7 Sep 2015 02:55:01 +0000 (10:55 +0800)]
ARM: dts: imx7d: add fec1 and fec2 support for i.MX7d soc
Add fec1 and fec2 nodes for i.MX7d soc.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Horia Geantă [Wed, 12 Aug 2015 07:42:41 +0000 (10:42 +0300)] 
ARM: dts: ls1021a: add crypto node
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Haibo Chen [Fri, 28 Aug 2015 09:09:36 +0000 (17:09 +0800)] 
ARM: dts: imx6ul-14x14-evk.dts: add tsc support
Add touch screen surpport for i.MX6UL-EVK board.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Haibo Chen [Fri, 28 Aug 2015 09:09:35 +0000 (17:09 +0800)]
ARM: dts: imx6ul.dtsi: add TSC support
Add imx6ul touchscreen controller support.
TSC module need ADC2 module to measure the touchscreen
coordinate value. This patch put TSC and ADC2 together,
make ADC2 module only be used for TSC, can't be used as
a normal ADC.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 2 Sep 2015 18:16:20 +0000 (15:16 -0300)]
ARM: dts: imx7d: Add PWM support
Add the PWM1-4 nodes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 2 Sep 2015 15:55:21 +0000 (12:55 -0300)]
ARM: dts: imx6sl: Complete the dcp node
The DCP block present on MX6SL is compatible with the one on MX28,
so add the compatible string and also complete the interrupt entries.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rafał Miłecki [Sun, 16 Aug 2015 06:39:17 +0000 (08:39 +0200)] 
ARM: dts: imx: add "jedec,spi-nor" flash compatible binding
Starting with commit
8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Wahren [Wed, 12 Aug 2015 22:21:56 +0000 (22:21 +0000)] 
ARM: mxs: enable ocotp for i.MX23 and i.MX28
This patch enables On Chip OTP support for i.MX23 and i.MX28 SoCs,
but keeps the old compatible string.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Haibo Chen [Tue, 11 Aug 2015 11:38:29 +0000 (19:38 +0800)]
ARM: dts: imx7d-sdb: add eMMC5.0 support
imx7d-sdb board has a eMMC5.0 on usdhc3. This eMMC support HS400.
This patch add usdhc3 support for HS400
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Sun, 6 Sep 2015 07:29:34 +0000 (15:29 +0800)] 
ARM: dts: imx6ul: add pm_power_off support
i.MX6UL can be powered off by programming SNVS.
When long press ON/OFF button(5 seconds),
PMIC_ON_REQ pin will be set to low and external
PMIC will be powered off.
And system can be powered on by long press ON/OFF
button again.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Tue, 4 Aug 2015 17:48:36 +0000 (01:48 +0800)]
ARM: dts: imx6ul: add mmdc support for i.mx6ul
Add MMDC support for i.MX6UL.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This page took 0.047891 seconds and 5 git commands to generate.
projects / deliverable / linux.git / log
