Arnd Bergmann [Thu, 24 Apr 2014 13:35:58 +0000 (15:35 +0200)]
Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
ARM: dts: am335x: update USB DT references
ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
ARM: AM335X: EVM: fix pinmux documentation in devicetree
ARM: OMAP2+: N900: remove omapdss init for DT boot
ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
ARM: dts: omap5: Add clocks to USB3 PHY node
ARM: OMAP2+: hwmod: fix missing braces in _init()
ARM: AM43xx: fix dpll init in bypass mode
ARM: OMAP3: hwmod data: Correct clock domains for USB modules
ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 24 Apr 2014 13:35:14 +0000 (15:35 +0200)]
Merge tag 'ux500-defconfig-for-arm-soc' of git://git./linux/kernel/git/linusw/linux-stericsson into fixes
This is a patch set for some ST-Ericsson devices:
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure for CW1200 WLAN chip
ARM: ux500: configure in sensors
ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 24 Apr 2014 13:34:34 +0000 (15:34 +0200)]
Merge tag 'renesas-fixes-for-v3.15' of git://git./linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes Updates for v3.15
r8a7791 (R-Car M2) based koelsch board
* Correct renesas,gpios to renesas,groups in sd[012] pfc
8a7790 (R-Car H2) based lager board
* Correct SND_SOC_DAIFMT_CBx_CFx flags
r8a7740 (R-Mobile A1) SoC
* Drop address cells from GIC node
r8a7740 (R-Mobile A1) based Armadillo800 EVA board
* Correct SND_SOC_DAIFMT_CBx_CFx flags
sh73a0 (SH-Mobile AG5) SoC
* Drop address cells from GIC node
* tag 'renesas-fixes-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: koelsch: correct renesas,gpios to renesas,groups in sd[012] pfc
ARM: shmobile: r8a7740: drop address cells from GIC node
ARM: shmobile: sh73a0: drop address cells from GIC node
ARM: shmobile: armadillo800eva: fixup SND_SOC_DAIFMT_CBx_CFx flags
ARM: shmobile: lager: fixup SND_SOC_DAIFMT_CBx_CFx flags
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 24 Apr 2014 13:34:00 +0000 (15:34 +0200)]
Merge tag 'renesas-dt5-for-v3.15' of git://git./linux/kernel/git/horms/renesas into fixes
Fifth Round of Renesas ARM Based SoC DT Updates for v3.15
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
* tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 24 Apr 2014 13:33:31 +0000 (15:33 +0200)]
Merge tag 'v3.15-rockchip-fixes1' of git://git./linux/kernel/git/mmind/linux-rockchip into fixes
Fixing uart-rx pull settings and a copy'n'paste error in a smp message
* tag 'v3.15-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: fix copy'n'paste error in smp error messages
ARM: rockchip: rk3188: enable pull-ups on UART RX pins
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 24 Apr 2014 13:30:53 +0000 (15:30 +0200)]
Merge tag 'imx-fixes-3.15' of git://git./linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 3.15:
- A couple of dts changes for the fallout of imx-drm binding update
- Parent DI clocks to video PLL for better HDMI support
- PCIe interrupt mapping and GIC node fixes
- A series of edmqmx6 board fixes
- Other small and random fixes on imx5 and imx6 dts
* tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: i.MX6: ipu_di_sel clocks can set parent rates
ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel
ARM: dts: imx: add required #clock-cells for fixed-clock
ARM: dts: vybrid: drop address and size cells from GIC node
ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11
ARM: dts: imx53: fix apparent copy/paste error
ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property
ARM: dts: imx53-tx53: add IPU DI ports and endpoints
ARM: dts: imx6: edmqmx6: add second STMPE
ARM: dts: imx6: edmqmx6: USB H1 only supports host mode
ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator
ARM: dts: imx6: edmqmx6: Fix usbotg id pin
ARM: dt: microsom: don't set bit 7 for ethernet mux settings
ARM: imx6q-clk: parent lvds_gate from lvds_sel
ARM: dts: imx: drop invalid size and address cells properties
ARM: dts: mx5: fix wrong stmpe-ts bindings
ARM: dts: imx53-m53evk: Fix memory region description
ARM: dts: imx53-qsb-common: Fix memory region description
ARM: dts: imx6: add PCIe interrupt mapping properties
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 24 Apr 2014 13:30:16 +0000 (15:30 +0200)]
Merge tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu into fixes
mvebu DT fixes-non-critical (for v3.15-rc1)
- kirkwood
- add some missing vendor prefixes to keep checkpatch happy
- mvebu
- add clock ref to mdio node on 370/XP/38x
* tag 'mvebu-dt-fixes-non-crit-3.15' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: ensure the mdio node has a clock reference on Armada 38x
ARM: mvebu: ensure the mdio node has a clock reference on Armada 370/XP
ARM: Kirkwood: DT: Add missing vendor prefix
ARM: Kirkwood: Fix Atmel vendor prefix
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Paul Bolle [Mon, 7 Apr 2014 16:52:23 +0000 (10:52 -0600)]
ARM: tegra: remove TEGRA_EMC_SCALING_ENABLE
Commit
a7cbe92cef27 ("ARM: tegra: remove tegra EMC scaling driver")
removed the only user of TEGRA_EMC_SCALING_ENABLE. Remove its Kconfig
entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Domenico Andreoli [Mon, 14 Apr 2014 09:55:01 +0000 (11:55 +0200)]
ARM: Tidy up DTB Makefile entries
Few things were out of order:
- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
list sorted
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring [Wed, 16 Apr 2014 13:42:13 +0000 (08:42 -0500)]
ARM: fix missing CLKSRC_OF on multi-platform
In commit
ddb902cc34593e (ARM: centralize common multi-platform kconfig
options), CLKSRC_OF was removed from some platforms, but not added to
ARCH_MULTIPLATFORM. Fix this.
Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Alex Elder [Wed, 9 Apr 2014 14:01:12 +0000 (09:01 -0500)]
ARM: spear: add __init to spear_clocksource_init()
I get a build warning because spear_clocksource_init() calls
clocksource_mmio_init(), but it doesn't have an __init annotation.
Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Andrea Adami [Tue, 8 Apr 2014 12:53:44 +0000 (14:53 +0200)]
ARM: pxa: hx4700.h: include "irqs.h" for PXA_NR_BUILTIN_GPIO
hx4700 needs the same fix as in
9705e74671f0e4f994d86b00cecf441917c64a66
"ARM: pxa: fix various compilation problems"
Fix build errors. Initial one is:
/linux/arch/arm/mach-pxa/include/mach/hx4700.h:18:32: error:
'PXA_NR_BUILTIN_GPIO' undeclared here (not in a function)
| #define HX4700_ASIC3_GPIO_BASE PXA_NR_BUILTIN_GPIO
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tony Lindgren [Tue, 22 Apr 2014 02:26:13 +0000 (19:26 -0700)]
ARM: OMAP2+: Fix GPMC remap for devices using an offset
At least the smc91x driver expects the device to be at 0x300
offset from bus base address. This does not work currently
for GPMC when booted in device tree mode as it attempts to
remap the the allocated GPMC partition to the address
configured by the device tree plus the device offset.
Note that this works just fine when booted with legacy mode.
Let's fix the issue by just ignoring any device specific
offset while remapping. And let's make sure the remap
address confirms to the GPMC 16MB minimum granularity
as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits.
Otherwise we can get something like this:
omap-gpmc
6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Tue, 22 Apr 2014 02:26:13 +0000 (19:26 -0700)]
ARM: OMAP2+: Fix oops for GPMC free
If gpmc_cs_remap() fails we will get an error because we are calling
release_resource() on an uninitialized resource. Let's fix that by
checking the resource flags. And while at it, let's also make
gpmc_cs_delete_mem() use the res pointer that we already have to
avoid confusion.
Without this patch we can get the following error:
omap-gpmc
6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Unable to handle kernel NULL pointer dereference at virtual address
00000018
...
(gpmc_cs_free+0x94/0xc8)
(gpmc_probe_generic_child+0x178/0x1ec)
(gpmc_probe_dt+0x1bc/0x2cc)
(gpmc_probe+0x250/0x44c)
(platform_drv_probe+0x3c/0x6c)
(really_probe+0x74/0x208)
(driver_probe_device+0x34/0x50)
(bus_for_each_drv+0x60/0x8c)
(device_attach+0x80/0xa4)
(bus_probe_device+0x88/0xb0)
(device_add+0x320/0x450)
(of_platform_device_create_pdata+0x80/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)
(pdata_quirks_init+0x30/0x48)
(customize_machine+0x20/0x48)
(do_one_initcall+0x2c/0x14c)
(do_basic_setup+0x98/0xd8)
(kernel_init_freeable+0x12c/0x1e0)
(kernel_init+0x8/0xf0)
(ret_from_fork+0x14/0x2c)
Code:
e1a04000 e59f0070 eb195136 e5942010 (
e5923018)
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: tony Lindgren <tony@atomide.com>
Robert Nelson [Tue, 15 Apr 2014 15:09:59 +0000 (10:09 -0500)]
ARM: dts: Add support for the BeagleBoard xM A/B
BeagleBoard xM A/B has an inverted usb hub enable line vs the xM C
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
[tony@atomide.com: updated for missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Fri, 18 Apr 2014 23:46:53 +0000 (16:46 -0700)]
Merge tag 'for-v3.15-rc/omap-fixes-a' of git://git./linux/kernel/git/pjw/omap-pending into omap-for-v3.15/fixes
OMAP hwmod and clock fixes for v3.15-rc
A few OMAP hwmod and clock fixes for v3.15-rc. Probably the most useful
fix is the AM43xx DPLL patch.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.15-rc/
20140411130021/
Tony Lindgren [Fri, 18 Apr 2014 23:44:38 +0000 (16:44 -0700)]
Merge branch 'fixes-v3.15-rc1'; commit '
390403fd79821bbd0c3a0d83307df2be87047b36' into omap-for-v3.15/fixes
Geert Uytterhoeven [Fri, 28 Mar 2014 10:11:39 +0000 (11:11 +0100)]
ARM: dts: Grammar /that will/it will/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Geert Uytterhoeven [Fri, 28 Mar 2014 10:11:37 +0000 (11:11 +0100)]
ARM: dts: Grammar /is uses/ is used/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Kishon Vijay Abraham I [Tue, 1 Apr 2014 10:14:34 +0000 (15:44 +0530)]
ARM: OMAP2+: Fix config name for USB3 PHY
commit a70143 (drivers: phy: usb3/pipe3: Adapt pipe3 driver to Generic PHY
Framework) moved phy-omap-usb3 driver in drivers/usb/phy to drivers/phy and
also renamed the file to phy-ti-pipe3. It also renamed the config from
OMAP_USB3 to TI_PIPE3 in Kconfig. However the config name was not changed in
omap2plus_defconfig. Fixed it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Leigh Brown [Wed, 16 Apr 2014 11:26:35 +0000 (12:26 +0100)]
ARM: dts: am335x: update USB DT references
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Johan Hovold [Tue, 8 Apr 2014 09:20:17 +0000 (11:20 +0200)]
ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit
f40739faba8e ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wolfram Sang [Tue, 1 Apr 2014 16:38:13 +0000 (18:38 +0200)]
ARM: AM335X: EVM: fix pinmux documentation in devicetree
Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sebastian Reichel [Tue, 8 Apr 2014 20:51:18 +0000 (22:51 +0200)]
ARM: OMAP2+: N900: remove omapdss init for DT boot
Do not try to initialize display for DT boot, since omapdss
is now initialized via Device Tree. Without this patch the
display subsystem does not properly come up.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Peter Ujfalusi [Wed, 2 Apr 2014 13:46:25 +0000 (16:46 +0300)]
ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
The correct bit is 24 for AHCLKX.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Roger Quadros [Tue, 1 Apr 2014 10:37:27 +0000 (13:37 +0300)]
ARM: dts: omap5: Add clocks to USB3 PHY node
The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Heiko Stuebner [Fri, 11 Apr 2014 09:44:24 +0000 (11:44 +0200)]
ARM: rockchip: fix copy'n'paste error in smp error messages
The error emitted when mapping the pmu failed, wrongly mentions the sram.
Reported-by: Kent Borg <kentborg@borg.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Max Schwarz [Sun, 9 Mar 2014 19:43:11 +0000 (20:43 +0100)]
ARM: rockchip: rk3188: enable pull-ups on UART RX pins
The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.
Therefore change the rx-pin settings accordingly.
This also fixes a uart receive problem on mass production Radxa Rock boards.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Philipp Zabel [Mon, 14 Apr 2014 14:20:40 +0000 (16:20 +0200)]
ARM: i.MX6: ipu_di_sel clocks can set parent rates
To obtain exact pixel clocks, allow the DI clock selectors to influence
the PLLs that they are derived from.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Mon, 14 Apr 2014 14:20:39 +0000 (16:20 +0200)]
ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel
Route the video PLL to the display interface clocks via the di_pre_sel
and di_sel muxes by default.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Magnus Damm [Mon, 14 Apr 2014 10:13:21 +0000 (19:13 +0900)]
ARM: shmobile: koelsch: correct renesas,gpios to renesas,groups in sd[012] pfc
Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.
Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lucas Stach [Mon, 14 Apr 2014 14:18:17 +0000 (16:18 +0200)]
ARM: shmobile: r8a7740: drop address cells from GIC node
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lucas Stach [Mon, 14 Apr 2014 14:18:18 +0000 (16:18 +0200)]
ARM: shmobile: sh73a0: drop address cells from GIC node
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Linus Walleij [Mon, 14 Apr 2014 09:08:26 +0000 (11:08 +0200)]
ARM: ux500: configure for CW1200 WLAN chip
The CW1200 WLAN chip driver had been in the kernel for a while,
we only need to activate it for the Ux500 properly. The latter
require some elaborative work, but in the meantime, let's make
sure we atleast compile it in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 10 Apr 2014 14:31:53 +0000 (16:31 +0200)]
ARM: ux500: configure in sensors
This enables the STMicroelectronics MEMS sensors for accelerometer,
gyroscope, magnetometer and pressure that are mounted on the Ux500
models.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ulf Hansson [Wed, 26 Mar 2014 13:30:53 +0000 (14:30 +0100)]
ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED
Since there are SD-card support in u300, it's reasonable to
support partitions for block devices as default.
While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ulf Hansson [Wed, 26 Mar 2014 13:19:07 +0000 (14:19 +0100)]
ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED
There are both (e)MMC/SD-card support in ux500, thus it's reasonable to
support partitions for block devices as default.
While updating the defconfig, we rebase it towards Kconfig changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 10 Apr 2014 14:21:02 +0000 (16:21 +0200)]
ARM: ux500: update defconfig
Update the ux500 defconfig to match the latest output of
savedefconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kuninori Morimoto [Mon, 14 Apr 2014 00:59:47 +0000 (17:59 -0700)]
ARM: shmobile: armadillo800eva: fixup SND_SOC_DAIFMT_CBx_CFx flags
c7a507eea1db1430476289f525f9c853d5d485e8
(ASoC: fsi: fixup SND_SOC_DAIFMT_CBx_CFx flags)
exchanged sound flags, but armadillo800eva flags needs IB_NF.
The recorded sound will be noise without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Mon, 14 Apr 2014 00:59:34 +0000 (17:59 -0700)]
ARM: shmobile: lager: fixup SND_SOC_DAIFMT_CBx_CFx flags
e1508289404ab6ca28e0dc931612600f0441c417
(ASoC: rcar: fixup SND_SOC_DAIFMT_CBx_CFx flags)
corrected SND_SOC_DAIFMT_CBx_CFx definition.
But then, Lager board was maintenanced other branch.
This patch correct SND_SOC_DAIFMT_CBx_CFx flag for lager
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Shawn Guo [Fri, 11 Apr 2014 01:56:46 +0000 (09:56 +0800)]
ARM: dts: imx: add required #clock-cells for fixed-clock
Per bindings of fixed-clock, #clock-cells is a required property. Let's
add it for those fixed rate clocks.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Fri, 11 Apr 2014 14:59:38 +0000 (16:59 +0200)]
ARM: dts: vybrid: drop address and size cells from GIC node
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Fri, 11 Apr 2014 12:09:39 +0000 (09:09 -0300)]
ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11
In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:
m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)
In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lothar Waßmann [Thu, 10 Apr 2014 08:03:40 +0000 (10:03 +0200)]
ARM: dts: imx53: fix apparent copy/paste error
The 'remote-endpoint' property should point back to ipu_di1_lvds1
rather than ipu_di0_lvds0.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Thu, 10 Apr 2014 07:22:56 +0000 (15:22 +0800)]
ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property
Since commit (
655b43c staging: imx-drm-core: Use OF graph to find
components and connections between encoder and crtcs), 'crtcs' becomes a
dead property. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Shawn Guo [Thu, 10 Apr 2014 07:14:14 +0000 (15:14 +0800)]
ARM: dts: imx53-tx53: add IPU DI ports and endpoints
With the recent imx-drm device tree binding changes, we need to add IPU
DI ports and endpoints for adapting.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Lucas Stach [Mon, 7 Apr 2014 14:29:27 +0000 (16:29 +0200)]
ARM: dts: imx6: edmqmx6: add second STMPE
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Mon, 7 Apr 2014 14:29:26 +0000 (16:29 +0200)]
ARM: dts: imx6: edmqmx6: USB H1 only supports host mode
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Sascha Hauer [Mon, 7 Apr 2014 14:29:25 +0000 (16:29 +0200)]
ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator
GPIO7_12 switches the D+/D- USB lines on and off. When we use this as
VBUS regulator it means that USB device mode can never work as VBUS is
never turned on in Device mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Mon, 7 Apr 2014 14:29:24 +0000 (16:29 +0200)]
ARM: dts: imx6: edmqmx6: Fix usbotg id pin
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Russell King [Sun, 6 Apr 2014 22:32:25 +0000 (23:32 +0100)]
ARM: dt: microsom: don't set bit 7 for ethernet mux settings
Bit 6,7 are marked as reserved for the ethernet RGMII pins, so avoid
setting these bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Fri, 28 Mar 2014 16:52:52 +0000 (17:52 +0100)]
ARM: imx6q-clk: parent lvds_gate from lvds_sel
Allows fror proper refcounting of the parent clocks
when enabling the clock output on CLK1/2 pads.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Fri, 28 Mar 2014 16:25:51 +0000 (17:25 +0100)]
ARM: dts: imx: drop invalid size and address cells properties
Those two properties should have been set to zero, which
is the same as not specifying them.
Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Wed, 2 Apr 2014 17:05:37 +0000 (19:05 +0200)]
ARM: dts: mx5: fix wrong stmpe-ts bindings
Fix bindings for STMPE touchscreen controller to match the documented
bindings and the actual bindings used by the driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Fri, 28 Mar 2014 05:09:14 +0000 (02:09 -0300)]
ARM: dts: imx53-m53evk: Fix memory region description
On m53evk there are two DRAM chip selects:
CS0 at 0x70000000
CS1 at 0xb0000000
Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.
Fix the memory layout to describe the hardware appropriately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Fri, 28 Mar 2014 05:09:13 +0000 (02:09 -0300)]
ARM: dts: imx53-qsb-common: Fix memory region description
On mx53qsb there are two DRAM chip selects:
CS0 at 0x70000000
CS1 at 0xb0000000
Each bank has a 512MB DRAM, giving a total of 1GB of system DRAM.
Fix the memory layout to describe the hardware appropriately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Lucas Stach [Wed, 5 Mar 2014 13:25:50 +0000 (14:25 +0100)]
ARM: dts: imx6: add PCIe interrupt mapping properties
As defined by the common PCI bindings.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Linus Torvalds [Sun, 13 Apr 2014 21:18:35 +0000 (14:18 -0700)]
Linux 3.15-rc1
Geert Uytterhoeven [Sun, 13 Apr 2014 18:46:22 +0000 (20:46 +0200)]
mm: Initialize error in shmem_file_aio_read()
Some versions of gcc even warn about it:
mm/shmem.c: In function ‘shmem_file_aio_read’:
mm/shmem.c:1414: warning: ‘error’ may be used uninitialized in this function
If the loop is aborted during the first iteration by one of the two
first break statements, error will be uninitialized.
Introduced by commit
6e58e79db8a1 ("introduce copy_page_to_iter, kill
loop over iovec in generic_file_aio_read()").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Sun, 13 Apr 2014 18:46:21 +0000 (20:46 +0200)]
cifs: Use min_t() when comparing "size_t" and "unsigned long"
On 32 bit, size_t is "unsigned int", not "unsigned long", causing the
following warning when comparing with PAGE_SIZE, which is always "unsigned
long":
fs/cifs/file.c: In function ‘cifs_readdata_to_iov’:
fs/cifs/file.c:2757: warning: comparison of distinct pointer types lacks a cast
Introduced by commit
7f25bba819a3 ("cifs_iovec_read: keep iov_iter
between the calls of cifs_readdata_to_iov()"), which changed the
signedness of "remaining" and the code from min_t() to min().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 13 Apr 2014 20:28:13 +0000 (13:28 -0700)]
Merge branch 'slab/next' of git://git./linux/kernel/git/penberg/linux
Pull slab changes from Pekka Enberg:
"The biggest change is byte-sized freelist indices which reduces slab
freelist memory usage:
https://lkml.org/lkml/2013/12/2/64"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: slab/slub: use page->list consistently instead of page->lru
mm/slab.c: cleanup outdated comments and unify variables naming
slab: fix wrongly used macro
slub: fix high order page allocation problem with __GFP_NOFAIL
slab: Make allocations with GFP_ZERO slightly more efficient
slab: make more slab management structure off the slab
slab: introduce byte sized index for the freelist of a slab
slab: restrict the number of objects in a slab
slab: introduce helper functions to get/set free object
slab: factor out calculate nr objects in cache_estimate
Linus Torvalds [Sun, 13 Apr 2014 01:22:27 +0000 (18:22 -0700)]
Merge branch 'misc' of git://git./linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"Here is the non-critical part of kbuild:
- One bogus coccinelle check removed, one check fixed not to suggest
the obsolete PTR_RET macro
- scripts/tags.sh does not index the generated *.mod.c files
- new objdiff tool to list differences between two versions of an
object file
- A fix for scripts/bootgraph.pl"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/coccinelle: Use PTR_ERR_OR_ZERO
scripts/bootgraph.pl: Add graphic header
scripts: objdiff: detect object code changes between two commits
Coccicheck: Remove memcpy to struct assignment test
scripts/tags.sh: Ignore *.mod.c
Mikulas Patocka [Wed, 9 Apr 2014 01:52:05 +0000 (21:52 -0400)]
sym53c8xx_2: Set DID_REQUEUE return code when aborting squeue
This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.
When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.
This function aborts them with DID_SOFT_ERROR.
If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.
The result is that disk returning QUEUE FULL causes request failures.
The error was reproduced on 53c895 with COMPAQ
BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags. The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags. The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mackerras [Fri, 11 Apr 2014 06:43:35 +0000 (16:43 +1000)]
powerpc: Don't try to set LPCR unless we're in hypervisor mode
Commit
8f619b5429d9 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode. The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic. The visible result is that
the kernel hangs after printing "returning from prom_init".
This fixes it by checking for hypervisor mode being available before
setting LPCR. If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davidlohr Bueso [Wed, 9 Apr 2014 18:55:07 +0000 (11:55 -0700)]
futex: update documentation for ordering guarantees
Commits
11d4616bd07f ("futex: revert back to the explicit waiter
counting code") and
69cd9eba3886 ("futex: avoid race between requeue and
wake") changed some of the finer details of how we think about futexes.
One was a late fix and the other a consequence of overlooking the whole
requeuing logic.
The first change caused our documentation to be incorrect, and the
second made us aware that we need to explicitly add more details to it.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 13 Apr 2014 00:31:22 +0000 (17:31 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull yet more networking updates from David Miller:
1) Various fixes to the new Redpine Signals wireless driver, from
Fariya Fatima.
2) L2TP PPP connect code takes PMTU from the wrong socket, fix from
Dmitry Petukhov.
3) UFO and TSO packets differ in whether they include the protocol
header in gso_size, account for that in skb_gso_transport_seglen().
From Florian Westphal.
4) If VLAN untagging fails, we double free the SKB in the bridging
output path. From Toshiaki Makita.
5) Several call sites of sk->sk_data_ready() were referencing an SKB
just added to the socket receive queue in order to calculate the
second argument via skb->len. This is dangerous because the moment
the skb is added to the receive queue it can be consumed in another
context and freed up.
It turns out also that none of the sk->sk_data_ready()
implementations even care about this second argument.
So just kill it off and thus fix all these use-after-free bugs as a
side effect.
6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti.
7) pktgen needs to do locking properly for LLTX devices, from Daniel
Borkmann.
8) xen-netfront driver initializes TX array entries in RX loop :-) From
Vincenzo Maffione.
9) After refactoring, some tunnel drivers allow a tunnel to be
configured on top itself. Fix from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vti: don't allow to add the same tunnel twice
gre: don't allow to add the same tunnel twice
drivers: net: xen-netfront: fix array initialization bug
pktgen: be friendly to LLTX devices
r8152: check RTL8152_UNPLUG
net: sun4i-emac: add promiscuous support
net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
net: ipv6: Fix oif in TCP SYN+ACK route lookup.
drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts
drivers: net: cpsw: discard all packets received when interface is down
net: Fix use after free by removing length arg from sk_data_ready callbacks.
Drivers: net: hyperv: Address UDP checksum issues
Drivers: net: hyperv: Negotiate suitable ndis version for offload support
Drivers: net: hyperv: Allocate memory for all possible per-pecket information
bridge: Fix double free and memory leak around br_allowed_ingress
bonding: Remove debug_fs files when module init fails
i40evf: program RSS LUT correctly
i40evf: remove open-coded skb_cow_head
ixgb: remove open-coded skb_cow_head
igbvf: remove open-coded skb_cow_head
...
Linus Torvalds [Sun, 13 Apr 2014 00:26:45 +0000 (17:26 -0700)]
Merge tag 'blackfin-for-linus' of git://git./linux/kernel/git/realmz6/blackfin-linux
Pull blackfin updates from Steven Miao:
"Code cleanup, some previously ignored patches, and bug fixes"
* tag 'blackfin-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/realmz6/blackfin-linux:
blackfin: cleanup board files
bf609: clock: drop unused clock bit set/clear functions
Blackfin: bf537: rename "CONFIG_ADT75"
Blackfin: bf537: rename "CONFIG_AD7314"
Blackfin: bf537: rename ad2s120x ->ad2s1200
blackfin: bf537: fix typo "CONFIG_SND_SOC_ADV80X_MODULE"
blackfin: dma: current count mmr is read only
bfin_crc: Move architecture independant crc header file out of the blackfin folder.
bf54x: drop unuesd HOST status,control,timeout registers bit define macros
blackfin: portmux: cleanup head file
Blackfin: remove "config IP_CHECKSUM_L1"
blackfin: Remove GENERIC_GPIO config option again
blackfin:Use generic /proc/interrupts implementation
blackfin: bf60x: fix typo "CONFIG_PM_BFIN_WAKE_PA15_POL"
Linus Torvalds [Sun, 13 Apr 2014 00:23:12 +0000 (17:23 -0700)]
Merge tag 'remoteproc-3.15-cleanups' of git://git./linux/kernel/git/ohad/remoteproc
Pull remoteproc cleanups from Ohad Ben-Cohen:
"Several remoteproc cleanup patches coming from Jingoo Han, Julia
Lawall and Uwe Kleine-König"
* tag 'remoteproc-3.15-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc/ste_modem: staticize local symbols
remoteproc/davinci: simplify use of devm_ioremap_resource
remoteproc/davinci: drop needless devm_clk_put
Linus Torvalds [Sun, 13 Apr 2014 00:00:40 +0000 (17:00 -0700)]
Merge tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel
Pull llvm patches from Behan Webster:
"These are some initial updates to support compiling the kernel with
clang.
These patches have been through the proper reviews to the best of my
ability, and have been soaking in linux-next for a few weeks. These
patches by themselves still do not completely allow clang to be used
with the kernel code, but lay the foundation for other patches which
are still under review.
Several other of the LLVMLinux patches have been already added via
maintainer trees"
* tag 'llvmlinux-for-v3.15' of git://git.linuxfoundation.org/llvmlinux/kernel:
x86: LLVMLinux: Fix "incomplete type const struct x86cpu_device_id"
x86 kbuild: LLVMLinux: More cc-options added for clang
x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI
LLVMLinux: Add support for clang to compiler.h and new compiler-clang.h
LLVMLinux: Remove warning about returning an uninitialized variable
kbuild: LLVMLinux: Fix LINUX_COMPILER definition script for compilation with clang
Documentation: LLVMLinux: Update Documentation/dontdiff
kbuild: LLVMLinux: Adapt warnings for compilation with clang
kbuild: LLVMLinux: Add Kbuild support for building kernel with Clang
Linus Torvalds [Sat, 12 Apr 2014 23:51:08 +0000 (16:51 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target pending updates for v3.15-rc1. Apologies in
advance for waiting until the second to last day of the merge window
to send these out.
The highlights this round include:
- iser-target support for T10 PI (DIF) offloads (Sagi + Or)
- Fix Task Aborted Status (TAS) handling in target-core (Alex Leung)
- Pass in transport supported PI at session initialization (Sagi + MKP + nab)
- Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi)
- Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab)
- Fix tcm_fc use-after-free of ft_tpg (Andy Grover)
- Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn)
Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI
metadata into KVM guest have been left-out for now, as there where a
few comments from MST + Paolo that where not able to be addressed in
time for v3.15. Please expect this feature for v3.16-rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits)
ib_srpt: Use correct ib_sg_dma primitives
target/tcm_fc: Rename ft_tport_create to ft_tport_get
target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn
target/tcm_fc: Rename structs and list members for clarity
target/tcm_fc: Limit to 1 TPG per wwn
target/tcm_fc: Don't export ft_lport_list
target/tcm_fc: Fix use-after-free of ft_tpg
target: Add check to prevent Abort Task from aborting itself
target: Enable READ_STRIP emulation in target_complete_ok_work
target/sbc: Add sbc_dif_read_strip software emulation
target: Enable WRITE_INSERT emulation in target_execute_cmd
target/sbc: Add sbc_dif_generate software emulation
target/sbc: Only expose PI read_cap16 bits when supported by fabric
target/spc: Only expose PI mode page bits when supported by fabric
target/spc: Only expose PI inquiry bits when supported by fabric
target: Pass in transport supported PI at session initialization
target/iblock: Fix double bioset_integrity_free bug
Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist
target/rd: T10-Dif: RAM disk is allocating more space than required.
iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug
...
Linus Torvalds [Sat, 12 Apr 2014 23:18:17 +0000 (16:18 -0700)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of bug fix patches for v3.15-rc1. Most are just driver
fixes. There are some changes at remote controller core level, fixing
some definitions on a new API added for Kernel v3.15.
It also adds the missing include at include/uapi/linux/v4l2-common.h,
to allow its compilation on userspace, as pointed by you"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (24 commits)
[media] gpsca: remove the risk of a division by zero
[media] stk1160: warrant a NUL terminated string
[media] v4l: ti-vpe: retain v4l2_buffer flags for captured buffers
[media] v4l: ti-vpe: Set correct field parameter for output and capture buffers
[media] v4l: ti-vpe: zero out reserved fields in try_fmt
[media] v4l: ti-vpe: Fix initial configuration queue data
[media] v4l: ti-vpe: Use correct bus_info name for the device in querycap
[media] v4l: ti-vpe: report correct capabilities in querycap
[media] v4l: ti-vpe: Allow usage of smaller images
[media] v4l: ti-vpe: Use video_device_release_empty
[media] v4l: ti-vpe: Make sure in job_ready that we have the needed number of dst_bufs
[media] lgdt3305: include sleep functionality in lgdt3304_ops
[media] drx-j: use customise option correctly
[media] m88rs2000: fix sparse static warnings
[media] r820t: fix size and init values
[media] rc-core: remove generic scancode filter
[media] rc-core: split dev->s_filter
[media] rc-core: do not change 32bit NEC scancode format for now
[media] rtl28xxu: remove duplicate ID 0458:707f Genius TVGo DVB-T03
[media] xc2028: add missing break to switch
...
Linus Torvalds [Sat, 12 Apr 2014 23:16:39 +0000 (16:16 -0700)]
Merge tag 'ntb-3.15' of git://github.com/jonmason/ntb
Pull PCIe non-transparent bridge fixes and features from Jon Mason:
"NTB driver bug fixes to address issues in list traversal, skb leak in
ntb_netdev, a typo, and a leak of msix entries in the error path.
Clean ups of the event handling logic, as well as a overall style
cleanup. Finally, the driver was converted to use the new
pci_enable_msix_range logic (and the refactoring to go along with it)"
* tag 'ntb-3.15' of git://github.com/jonmason/ntb:
ntb: Use pci_enable_msix_range() instead of pci_enable_msix()
ntb: Split ntb_setup_msix() into separate BWD/SNB routines
ntb: Use pci_msix_vec_count() to obtain number of MSI-Xs
NTB: Code Style Clean-up
NTB: client event cleanup
ntb: Fix leakage of ntb_device::msix_entries[] array
NTB: Fix typo in setting one translation register
ntb_netdev: Fix skb free issue in open
ntb_netdev: Fix list_for_each_entry exit issue
Linus Torvalds [Sat, 12 Apr 2014 22:39:53 +0000 (15:39 -0700)]
ceph: fix pr_fmt() redefinition
The vfs merge caused a latent bug to show up:
In file included from fs/ceph/super.h:4:0,
from fs/ceph/ioctl.c:3:
include/linux/ceph/ceph_debug.h:4:0: warning: "pr_fmt" redefined [enabled by default]
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
^
In file included from include/linux/kernel.h:13:0,
from include/linux/uio.h:12,
from include/linux/socket.h:7,
from include/uapi/linux/in.h:22,
from include/linux/in.h:23,
from fs/ceph/ioctl.c:1:
include/linux/printk.h:214:0: note: this is the location of the previous definition
#define pr_fmt(fmt) fmt
^
where the reason is that <linux/ceph_debug.h> is included much too late
for the "pr_fmt()" define.
The include of <linux/ceph_debug.h> needs to be the first include in the
file, but fs/ceph/ioctl.c had for some reason missed that, and it wasn't
noticeable until some unrelated header file changes brought in an
indirect earlier include of <linux/kernel.h>.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 12 Apr 2014 21:49:50 +0000 (14:49 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
David S. Miller [Sat, 12 Apr 2014 21:03:20 +0000 (17:03 -0400)]
Merge branch 'tunnels'
Nicolas Dichtel says:
====================
tunnels: don't allow to add the same tunnel twice
This series fixes the check of an existing tunnel with the same
parameters when a new tunnel is added. I've checked all users of
ip_tunnel_newlink(): gre, gretap, ipip and vti. The bug exists only
for gre and vti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Fri, 11 Apr 2014 13:51:19 +0000 (15:51 +0200)]
vti: don't allow to add the same tunnel twice
Before the patch, it was possible to add two times the same tunnel:
ip l a vti1 type vti remote 10.16.0.121 local 10.16.0.249 key 41
ip l a vti2 type vti remote 10.16.0.121 local 10.16.0.249 key 41
It was possible, because ip_tunnel_newlink() calls ip_tunnel_find() with the
argument dev->type, which was set only later (when calling ndo_init handler
in register_netdevice()). Let's set this type in the setup handler, which is
called before newlink handler.
Introduced by commit
b9959fd3b0fa ("vti: switch to new ip tunnel code").
CC: Cong Wang <amwang@redhat.com>
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Fri, 11 Apr 2014 13:51:18 +0000 (15:51 +0200)]
gre: don't allow to add the same tunnel twice
Before the patch, it was possible to add two times the same tunnel:
ip l a gre1 type gre remote 10.16.0.121 local 10.16.0.249
ip l a gre2 type gre remote 10.16.0.121 local 10.16.0.249
It was possible, because ip_tunnel_newlink() calls ip_tunnel_find() with the
argument dev->type, which was set only later (when calling ndo_init handler
in register_netdevice()). Let's set this type in the setup handler, which is
called before newlink handler.
Introduced by commit
c54419321455 ("GRE: Refactor GRE tunneling code.").
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincenzo Maffione [Sat, 12 Apr 2014 09:55:40 +0000 (11:55 +0200)]
drivers: net: xen-netfront: fix array initialization bug
This patch fixes the initialization of an array used in the TX
datapath that was mistakenly initialized together with the
RX datapath arrays. An out of range array access could happen
when RX and TX rings had different sizes.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 12 Apr 2014 20:36:44 +0000 (16:36 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, e1000e, igb, igbvf, ixgb, ixgbe,
ixgbevf and i40evf.
Mark fixes an issue with ixgbe and ixgbevf by adding a bit to indicate
when workqueues have been initialized. This permits the register read
error handling from attempting to use them prior to that, which also
generates warnings. Checking for a detected removal after initializing
the work queues allows the probe function to return an error without
getting the workqueue involved. Further, if the error_detected
callback is entered before the workqueues are initialized, exit without
recovery since the device initialization was so truncated.
Francois Romieu provides several patches to all the drivers to remove
the open coded skb_cow_head.
Jakub Kicinski provides a fix for igb where last_rx_timestamp should be
updated only when Rx time stamp is read.
Mitch provides a fix for i40evf where a recent change broke the RSS LUT
programming causing it to be programmed with all 0's.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 12 Apr 2014 20:06:10 +0000 (13:06 -0700)]
Merge tag 'trace-3.15-v2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull more tracing updates from Steven Rostedt:
"This includes the final patch to clean up and fix the issue with the
design of tracepoints and how a user could register a tracepoint and
have that tracepoint not be activated but no error was shown.
The design was for an out of tree module but broke in tree users. The
clean up was to remove the saving of the hash table of tracepoint
names such that they can be enabled before they exist (enabling a
module tracepoint before that module is loaded). This added more
complexity than needed. The clean up was to remove that code and just
enable tracepoints that exist or fail if they do not.
This removed a lot of code as well as the complexity that it brought.
As a side effect, instead of registering a tracepoint by its name, the
tracepoint needs to be registered with the tracepoint descriptor.
This removes having to duplicate the tracepoint names that are
enabled.
The second patch was added that simplified the way modules were
searched for.
This cleanup required changes that were in the 3.15 queue as well as
some changes that were added late in the 3.14-rc cycle. This final
change waited till the two were merged in upstream and then the change
was added and full tests were run. Unfortunately, the test found some
errors, but after it was already submitted to the for-next branch and
not to be rebased. Sparse errors were detected by Fengguang Wu's bot
tests, and my internal tests discovered that the anonymous union
initialization triggered a bug in older gcc compilers. Luckily, there
was a bugzilla for the gcc bug which gave a work around to the
problem. The third and fourth patch handled the sparse error and the
gcc bug respectively.
A final patch was tagged along to fix a missing documentation for the
README file"
* tag 'trace-3.15-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add missing function triggers dump and cpudump to README
tracing: Fix anonymous unions in struct ftrace_event_call
tracepoint: Fix sparse warnings in tracepoint.c
tracepoint: Simplify tracepoint module search
tracepoint: Use struct pointer instead of name hash for reg/unreg tracepoints
Linus Torvalds [Sat, 12 Apr 2014 19:38:53 +0000 (12:38 -0700)]
Merge git://git.infradead.org/users/eparis/audit
Pull audit updates from Eric Paris.
* git://git.infradead.org/users/eparis/audit: (28 commits)
AUDIT: make audit_is_compat depend on CONFIG_AUDIT_COMPAT_GENERIC
audit: renumber AUDIT_FEATURE_CHANGE into the 1300 range
audit: do not cast audit_rule_data pointers pointlesly
AUDIT: Allow login in non-init namespaces
audit: define audit_is_compat in kernel internal header
kernel: Use RCU_INIT_POINTER(x, NULL) in audit.c
sched: declare pid_alive as inline
audit: use uapi/linux/audit.h for AUDIT_ARCH declarations
syscall_get_arch: remove useless function arguments
audit: remove stray newline from audit_log_execve_info() audit_panic() call
audit: remove stray newlines from audit_log_lost messages
audit: include subject in login records
audit: remove superfluous new- prefix in AUDIT_LOGIN messages
audit: allow user processes to log from another PID namespace
audit: anchor all pid references in the initial pid namespace
audit: convert PPIDs to the inital PID namespace.
pid: get pid_t ppid of task in init_pid_ns
audit: rename the misleading audit_get_context() to audit_take_context()
audit: Add generic compat syscall support
audit: Add CONFIG_HAVE_ARCH_AUDITSYSCALL
...
Al Viro [Fri, 11 Apr 2014 16:01:03 +0000 (12:01 -0400)]
missing bits of "splice: fix racy pipe->buffers uses"
that commit has fixed only the parts of that mess in fs/splice.c itself;
there had been more in several other ->splice_read() instances...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Thu, 3 Apr 2014 14:27:17 +0000 (10:27 -0400)]
cifs: fix the race in cifs_writev()
O_APPEND handling there hadn't been completely fixed by Pavel's
patch; it checks the right value, but it's racy - we can't really
do that until i_mutex has been taken.
Fix by switching to __generic_file_aio_write() (open-coding
generic_file_aio_write(), actually) and pulling mutex_lock() above
inode_size_read().
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 4 Apr 2014 02:44:19 +0000 (22:44 -0400)]
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
ceph_osdc_put_request(ERR_PTR(-error)) oopses. What we want there
is break, not goto out.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Daniel Borkmann [Fri, 11 Apr 2014 11:22:00 +0000 (13:22 +0200)]
pktgen: be friendly to LLTX devices
Similarly to commit
43279500deca ("packet: respect devices with
LLTX flag in direct xmit"), we can basically apply the very same
to pktgen. This will help testing against LLTX devices such as
dummy driver (or others), which only have a single netdevice txq
and would otherwise require locking their txq from pktgen side
while e.g. in dummy case, we would not need any locking. Fix this
by making use of HARD_TX_{UN,}LOCK API, so that NETIF_F_LLTX will
be respected.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hayeswang [Fri, 11 Apr 2014 09:54:31 +0000 (17:54 +0800)]
r8152: check RTL8152_UNPLUG
When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Zyngier [Fri, 11 Apr 2014 09:46:17 +0000 (10:46 +0100)]
net: sun4i-emac: add promiscuous support
The sun4i-emac driver is rather primitive, and doesn't support
promiscuous mode. This makes usage such as bridging impossible,
which is a shame on virtualization capable HW such as the
Allwinner A20.
The fix is fairly simple: move the RX setup code to the ndo_set_rx_mode
vector, and add the required HW configuration when IFF_PROMISC is passed
by the core code.
This has been tested on a generic A20 box running a few virtual
machines hanging off a bridge with the EMAC chip as the link to the
outside world.
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duan Jiong [Fri, 11 Apr 2014 08:37:37 +0000 (16:37 +0800)]
net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steven Miao [Fri, 11 Apr 2014 18:07:27 +0000 (02:07 +0800)]
blackfin: cleanup board files
using IS_ENABLED() macro instead of defined(CONFIG_XXX) || defined(CONFIG_XXX_MODULE)
Signed-off-by: Steven Miao <realmz6@gmail.com>
Steven Miao [Fri, 11 Apr 2014 15:54:25 +0000 (23:54 +0800)]
bf609: clock: drop unused clock bit set/clear functions
Signed-off-by: Steven Miao <realmz6@gmail.com>
Paul Bolle [Thu, 4 Apr 2013 10:31:06 +0000 (12:31 +0200)]
Blackfin: bf537: rename "CONFIG_ADT75"
In v3.2 the Analog Devices ADT75 temperature sensor driver was removed
as an IIO driver and support for it was added to the LM75 HWMON driver.
But it was apparently overlooked to rename one reference to CONFIG_ADT75
to CONFIG_SENSORS_LM75. Do so now. Use the IS_ENABLED() macro, while
we're at it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Paul Bolle [Thu, 4 Apr 2013 10:08:25 +0000 (12:08 +0200)]
Blackfin: bf537: rename "CONFIG_AD7314"
In v3.2 the Analog Devices AD7314 temperature sensor driver was removed
as an IIO driver and added as a HWMON driver. But it was apparently
overlooked to rename two references to CONFIG_AD7314 to
CONFIG_SENSORS_AD7314. Do so now. Use the IS_ENABLED() macro, while
we're at it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Paul Bolle [Thu, 4 Apr 2013 11:02:10 +0000 (13:02 +0200)]
Blackfin: bf537: rename ad2s120x ->ad2s1200
In v3.2 the Analog Devices ad2s1200/ad2s1205 driver was renamed from
ad2s120x to ad2s1200. But it apparently forgot to rename the references
to this driver in the BF537-STAMP code. Rename these now, and use the
IS_ENABLED() macro, while we're at it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Paul Bolle [Fri, 8 Mar 2013 12:06:13 +0000 (13:06 +0100)]
blackfin: bf537: fix typo "CONFIG_SND_SOC_ADV80X_MODULE"
There's a (rather subtle) typo in "CONFIG_SND_SOC_ADV80X_MODULE". Fix it
once and for all by using IS_ENABLED(), which is designed to avoid
issues like this.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Sonic Zhang [Wed, 2 Apr 2014 08:57:23 +0000 (16:57 +0800)]
blackfin: dma: current count mmr is read only
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Sonic Zhang [Thu, 27 Mar 2014 08:34:31 +0000 (16:34 +0800)]
bfin_crc: Move architecture independant crc header file out of the blackfin folder.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
Steven Miao [Mon, 17 Mar 2014 06:49:26 +0000 (14:49 +0800)]
bf54x: drop unuesd HOST status,control,timeout registers bit define macros
Signed-off-by: Steven Miao <realmz6@gmail.com>
Steven Miao [Mon, 17 Mar 2014 05:36:51 +0000 (13:36 +0800)]
blackfin: portmux: cleanup head file
drop unused head file
change pinmux request/free macro for backward compatiblity
add function declaration
Signed-off-by: Steven Miao <realmz6@gmail.com>
Linus Torvalds [Sat, 12 Apr 2014 00:23:52 +0000 (17:23 -0700)]
Merge branch 'async-scsi-resume' of git://git./linux/kernel/git/djbw/isci
Pull async SCSI resume support from Dan Williams:
"Allow disks and other devices to resume in parallel.
This provides a tangible speed up for a non-esoteric use case (laptop
resume):
https://01.org/suspendresume/blogs/tebrandt/2013/hard-disk-resume-optimization-simpler-approach"
* 'async-scsi-resume' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/isci:
scsi: async sd resume
Linus Torvalds [Sat, 12 Apr 2014 00:20:38 +0000 (17:20 -0700)]
Merge tag 'md/3.15' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"Just a few md patches for the 3.15 merge window.
Not much happening in md/raid at the moment. Just a few bug fixes
(one for -stable) and a couple of performance tweaks"
* tag 'md/3.15' of git://neil.brown.name/md:
raid5: get_active_stripe avoids device_lock
raid5: make_request does less prepare wait
md: avoid oops on unload if some process is in poll or select.
md/raid1: r1buf_pool_alloc: free allocate pages when subsequent allocation fails.
md/bitmap: don't abuse i_writecount for bitmap files.
This page took 0.05089 seconds and 5 git commands to generate.