Fabio Estevam [Wed, 14 May 2014 19:53:55 +0000 (16:53 -0300)]
ARM: dts: imx6qdl-sabresd: Configure the ECSPI1 chip select pin
GPIO4_9 is used as ECSPI1 chip select and it needs to be configured as GPIO.
Configure the pin functionality explicitly in the dts file instead of relying
on the fact that it comes configured as GPIO from POR or from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Tue, 13 May 2014 14:48:15 +0000 (18:48 +0400)]
ARM: dts: Add support for the cpuimx27 board from Eukrea and its baseboard
This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 13 May 2014 13:43:36 +0000 (21:43 +0800)]
ARM: dts: imx: add initial imx6sx-sdb board support
Add initial imx6sx-sdb board support with limited devices enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 13 May 2014 12:21:35 +0000 (20:21 +0800)]
ARM: dts: imx: add initial imx6sx device tree source
Add initial device tree source for i.MX6 SoloX SoC.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Sun, 11 May 2014 13:59:26 +0000 (21:59 +0800)]
ARM: dts: imx: add pin function header for imx6sx
Add pin function header for i.MX6 SoloX SoC.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Fri, 18 Jul 2014 08:47:26 +0000 (16:47 +0800)]
Merge tag 'imx-soc-3.17' into imx/dt
The i.MX SoC changes for 3.17:
- Add devicetree support for i.MX1 and i.MX21 clock driver
- Use CLOCKSOURCE_OF_DECLARE() to initialize timer for DT targets
- Use of_clk_init() to initialize i.MX25 and i.MX27 clock driver in
device tree boot
- Remove i.MX1 camera support
- Remove i.MX27 IP Camera and Lite-Kit board support
- Add suspend and cpuidle support for i.mx6sx
- Clean up unused clk_register_clkdev() lookups
- Update imx-weim bus driver to support populating devices on a simple
bus
- Switch i.MX27 and i.MX6QDL clock driver to use macro for clock IDs
- Make i.MX51 a DT only platform and clean up the non-DT support code
- Support disabling supervisor protect via DT
- Random defconfig updates
Stefan Agner [Tue, 15 Jul 2014 12:56:19 +0000 (14:56 +0200)]
ARM: imx: clk-vf610: fix FlexCAN clock gating
Extend the clock control for FlexCAN with the second gate which
enable the clocks in the Clock Divider (CCM_CSCDR2) register too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sun, 13 Jul 2014 05:34:00 +0000 (09:34 +0400)]
ARM: i.MX: Use CLOCKSOURCE_OF_DECLARE() for DT targets
This patch uses clocksource_of_init() call for DT targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Steffen Trumtrar [Mon, 7 Jul 2014 09:41:27 +0000 (11:41 +0200)]
ARM: i.MX53: globally disable supervisor protect
Most peripherals on the i.MX53 have an
Off-Platform Peripheral Access Control Register (OPACR)
in which the access rights (together with the MPROT registers) can be declared.
However, this does not seem to work for example for SSI1+SDMA, because the
supervisor bit is not set for the SDMA unit.
It does work for SSI2, the QSB for example uses SSI2 for its audio. But SSI2 only
works because it does NOT have an OPACR.
The right solution would be to fix the access rights for the SDMA, but the unit
responsible for this is the Central Security Unit (CSU), which of course is NOT
documented. So, until documentation for this is openly available, turn off the
supervisor protection because it cripples the hardware.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Steffen Trumtrar [Mon, 7 Jul 2014 09:41:26 +0000 (11:41 +0200)]
ARM: i.MX: allow disabling supervisor protect via DT
The i.MX SoCs allow to setup fine grained access rights to peripherals on the
AIPS bus.
This is done via the Peripheral Access Register (PAR) in e.g. the i.MX21
or in later SoC versions the Off-Platform Peripheral Access Control Register
(OPACR), e.g. i.MX53.
Under certain circumstances this leads to problems in which bus masters are
not granted their access rights to peripherals.
To be able to disable these restrictions on DT platforms, add a helper function
that looks for AIPS nodes in the DT and disables them for every compatible node
it finds.
The compatible has to be declared in the mach-specific entry file, where this
helper function should then be called.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:36:09 +0000 (09:36 +0400)]
ARM: i.MX27 clk: Add 26 MHz oscillator circuit clock gate
This patch adds missing 26 MHz oscillator circuit clock gate support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:36:08 +0000 (09:36 +0400)]
ARM: i.MX27 clk: Remove unused definitions
This patch removes definitions which not used anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:36:06 +0000 (09:36 +0400)]
ARM: i.MX27 clk: Introduce DT include for clock provider
Use clock defines in order to make devicetrees more human readable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 05:00:01 +0000 (09:00 +0400)]
ARM: i.MX: Remove Freescale Logic Product Development i.MX27 Lite-Kit board support
The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board.
However, the support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 04:51:57 +0000 (08:51 +0400)]
ARM: i.MX: Remove excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27
This patch removes excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27.
Instead we use SOC_IMX*.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 5 Jul 2014 04:51:38 +0000 (08:51 +0400)]
ARM: i.MX: Remove i.MX1 camera support
i.MX1 camera driver has been removed by the commit
90b055898e.
This patch removes remaining support files for this camera.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabian Frederick [Fri, 4 Jul 2014 19:03:10 +0000 (21:03 +0200)]
ARM: imx: use PTR_ERR_OR_ZERO
replace IS_ERR/PTR_ERR
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Liu Ying [Fri, 4 Jul 2014 09:00:41 +0000 (17:00 +0800)]
bus: imx-weim: populate devices on a simple bus
There could be some memory map devices located in
a certain chip select region of the i.MX WEIM.
The devices could be attached to a simple bus(for
example, a AXI bus) whose root node is one child
device tree node of the i.MX WEIM device tree node.
There should be a bridge(very likely, software
transparent) bewteen the i.MX WEIM and the simple bus.
This patch makes the i.MX WEIM driver possible to
populate devices on a simple bus. In this way, people
may try various IPs(in a FPGA, maybe) outside of i.MX
chips with the i.MX WEIM embedded.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Arnd Bergmann [Thu, 3 Jul 2014 14:22:54 +0000 (16:22 +0200)]
ARM: imx: build cpu_is_imx6sl function conditionally
imx6q_pm_enter calls imx6sl_set_wait_clk when run on an imx6sl
based machine. However if support for imx6sl is not enabled
at compile time, this prevents us from building the kernel and
we get this link error instead:
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
:(.text+0x4b84): undefined reference to `imx6sl_set_wait_clk'
This makes the cpu_is_imx6sl function conditionally return false
if imx6sl is disabled at compile-time, which matches what the
older cpu_is_mx* macros did. We have similar inline functions for
the other imx6 variants, but so far I have not run into a case
where the extra #ifdef is necessary.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Arnd Bergmann [Thu, 3 Jul 2014 14:16:06 +0000 (16:16 +0200)]
ARM: imx: imx6sx uses imx6q cpuidle code
Building a kernel for imx6sx but without imx6q support results in
this link error because of the missing cpuidle driver:
arch/arm/mach-imx/built-in.o: In function `imx6sx_init_late'::(.init.text+0xc228):
undefined reference to `imx6q_cpuidle_init'
This patch adds a Makefile entry so we always build support for
the imx6q_cpuidle code when at least one of the 6sx or 6q variants
are enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Wed, 2 Jul 2014 07:24:30 +0000 (15:24 +0800)]
ARM: imx: drop PL310 errata 588369 and 727915
The PL310 integrated on i.MX6 series and VF610 are revision r3p1 and
later. Per ARM PL310 errata document, 588369 is fixed in r2p0 and
727915 is fixed in r3p1. Neither is needed for i.MX6 or VF610. So
let's drop them.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Stefan Agner [Wed, 2 Jul 2014 19:13:19 +0000 (21:13 +0200)]
ARM: imx_v6_v7_defconfig: add FSL_EDMA and PRINTK_TIME
Add EDMA for DMA support for Vybrid SoCs. Also add printk time.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 2 Jul 2014 14:58:51 +0000 (11:58 -0300)]
ARM: imx: clk-imx6sx: register SSI/SSI_IPG as shared gate clocks
SSI and SSI_IPG are clocks controlled by the same clock gating field, so
register them with imx_clk_gate2_shared.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Tue, 1 Jul 2014 11:09:02 +0000 (13:09 +0200)]
ARM: imx_v6_v7_defconfig: Enable flexcan driver for can support
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Silvio Fricke [Tue, 1 Jul 2014 11:08:58 +0000 (13:08 +0200)]
ARM: imx_v6_v7_defconfig: Enable STMPE gpio support
Enable STMPE gpio support as this is used on MX6 Data Modul edm-qmx6
board.
Signed-off-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 1 Jul 2014 08:03:00 +0000 (16:03 +0800)]
ARM: imx: mark .dt_compat as const
Otherwise GCC will mark the .init.rodata section R/W, which causes
a compile error once we add other real R/O data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Tue, 1 Jul 2014 03:12:52 +0000 (00:12 -0300)]
ARM: mx6: Only check for 1.2GHz for mx6quad
It is only the mx6quad variant that can run up to 1.2GHz, so add the check
accordingly.
This avoids getting the following warning on a mx6solo:
failed to disable 1.2 GHz OPP
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Wed, 25 Jun 2014 20:28:53 +0000 (17:28 -0300)]
ARM: imx_v4_v5_defconfig: Add USB device options
Allow USB device to work by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Denis Carikli [Wed, 25 Jun 2014 12:41:36 +0000 (14:41 +0200)]
ARM: i.MX25 clk: Use of_clk_init() for DT case
Replace .init_time() hook with of_clk_init() for DT targets.
Based on:
d4347ee ARM: i.MX27 clk: Use of_clk_init() for DT case
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Denis Carikli [Wed, 25 Jun 2014 12:41:34 +0000 (14:41 +0200)]
ARM i.MX25 clk: Fix gpt timer clock.
The gpt0 timer clock has been wrong since:
6bbaec5 ARM i.MX25: implement clocks using common clock framework
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sun, 22 Jun 2014 13:17:09 +0000 (17:17 +0400)]
ARM: i.MX21 clk: Add devicetree support
This patch adds devicetree support CCM module for i.MX21 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sun, 22 Jun 2014 13:17:08 +0000 (17:17 +0400)]
ARM: i.MX21 clk: Cleanup driver
This is a cleanup for i.MX21 clk driver. This change includes:
- Reduce license text.
- Remove unused definitions.
- Remove unused #include and sort the rest.
- Remove useless comment.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sun, 22 Jun 2014 13:17:07 +0000 (17:17 +0400)]
ARM: i.MX21 clk: Remove clk_register_clkdev() for unused clocks
This patch removes clk_register_clkdev() for the clocks that do not
have any users for boards and drivers.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sun, 22 Jun 2014 13:17:06 +0000 (17:17 +0400)]
ARM: i.MX21 clk: Clock initialization rework
This patch perform rework i.MX21 clock initialization. This includes
adding missing clocks and sort clocks by register address.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Tue, 24 Jun 2014 18:42:58 +0000 (15:42 -0300)]
ARM: clk-imx51-imx53: Remove clk_register_clkdev()
mx51 and mx53 are device tree only platforms, so we no longer need all these
calls to clk_register_clkdev().
Only keep cpu0 and gpc_dvfs clk_register_clkdev() calls.
Tested on imx51-babbage and imx53-qsb boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anson Huang [Mon, 23 Jun 2014 08:42:44 +0000 (16:42 +0800)]
ARM: imx: add standby mode support for suspend
Add standby mode support for suspend, to enter standby mode:
echo standby > /sys/power/state;
Use UART or RTC alarm to wake up system, when system enters
standby mode, SOC will enter STOP mode with ARM core kept
power on and 24M XTAL on.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anson Huang [Mon, 23 Jun 2014 08:42:43 +0000 (16:42 +0800)]
ARM: imx: mem bit must be cleared before entering DSM mode
According to hardware design, mem bit must be clear before
entering DSM mode, as ARM core will be power gated in DSM mode.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Sun, 15 Jun 2014 11:35:10 +0000 (19:35 +0800)]
ARM: imx6qdl: switch to use macro for clock ID
Instead of using enum for clock ID, let's switch imx6qdl clock driver to
use macro. In this case, device tree can reuse these macros to improve
readability.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anson Huang [Fri, 20 Jun 2014 05:44:05 +0000 (13:44 +0800)]
ARM: imx: add cpuidle support for i.mx6sx
Add cpuidle support for i.MX6SX, derive from i.MX6Q's
cpuidle, two levels supported:
1. WFI;
2. WAIT mode.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Anson Huang [Fri, 20 Jun 2014 05:20:54 +0000 (13:20 +0800)]
ARM: imx: add suspend support for i.mx6sx
Add suspend support for i.MX6SX.
To enter suspend, echo mem > /sys/power/state.
To exit suspend, using RTC alarm or enable debug UART wakeup.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Wed, 18 Jun 2014 17:26:39 +0000 (21:26 +0400)]
ARM: i.MX: Remove Freescale i.MX27 IP Camera board support
The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board. However, the
support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Fri, 13 Jun 2014 07:26:13 +0000 (11:26 +0400)]
ARM: i.MX system: Add a reset fallback if base address of watchdog is not set
This patch adds a reset fallback if base address of watchdog is not set.
This is intended for a targets not compatible with imx-21 watchdog,
i.MX1 for example.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Fri, 13 Jun 2014 07:26:12 +0000 (11:26 +0400)]
ARM: i.MX system: Simplify handling watchdog clock
This patch simplifies handling watchdog clock a bit.
As an additional change, now we properly check WDT clock in a reset
function.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Tue, 17 Jun 2014 00:15:52 +0000 (21:15 -0300)]
ARM: imx_v6_v7_defconfig: Select CONFIG_SOC_IMX6SX
Let mx6sx be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Tue, 10 Jun 2014 15:40:26 +0000 (19:40 +0400)]
ARM: i.MX clk: Move clock check function in common location
This patch moves clock check function in common i.MX location
and switch i.MX clk drivers to use this new function.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 7 Jun 2014 16:09:26 +0000 (20:09 +0400)]
ARM: i.MX27 clk: Use of_clk_init() for DT case
Replace .init_time() hook with of_clk_init() for DT targets.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Sat, 7 Jun 2014 16:09:25 +0000 (20:09 +0400)]
ARM: i.MX27 clk: Separate DT and non-DT init procedure
This patch separates DT and non-DT clock initialization procedure,
so we can avoid a lot of unneeded clk_register_clkdev() for DT case.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Tue, 27 May 2014 09:04:47 +0000 (13:04 +0400)]
ARM: i.MX: Remove excess variable
Base address for driver is global, there are no need to use
intermediate variable for it.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Tue, 27 May 2014 09:04:46 +0000 (13:04 +0400)]
ARM: i.MX: Use of_clk_get_by_name() for timer clocks for DT case.
Use of_clk_get_by_name() for timer clocks for DT case.
This patch eliminates a lot of unneeded clk_register_clkdev()
calls for GPT.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam [Fri, 23 May 2014 13:27:37 +0000 (10:27 -0300)]
ARM: imx: defconfig: Select CONFIG_FHANDLE
CONFIG_FHANDLE=y is needed when running systemd with version >=210, so that it
can spawn a serial tty via getty.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 07:54:58 +0000 (15:54 +0800)]
ARM: imx5: remove mx51.h and mx53.h
Now all the macros in mx51.h and mx53.h are used nowhere, so remove
them.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 07:09:42 +0000 (15:09 +0800)]
ARM: imx5: clean function declarations in mx51.h
The mx51_display_revision() is a dead declaration. Remove it. Also,
move mx51_revision() into common.h.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 07:46:46 +0000 (15:46 +0800)]
ARM: imx5: remove file mm-imx5.c
The only code left in mm-imx5.c is to create static mapping. While all
IMX platform code are moved to use dynamic mapping, the file can just be
removed now.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 07:34:06 +0000 (15:34 +0800)]
ARM: imx5: move init hooks into mach-imx5x.c
These imx5 init_early[late] hooks are called only from mach-imx5x.c.
Let's move them into mach-imx5x.c.
While at it, replace the static mapping in imx51_ipu_mipi_setup() with
dynamic mapping. Also this function and imx_src_init() do not
necessarily to be called at .init_early hook, so move them into
.init_machine.
The mxc_iomux_v3_init() is dropped from imx51_init_early() in the
moving, since it's only needed by non-DT boot.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 06:55:15 +0000 (14:55 +0800)]
ARM: imx5: use dynamic mapping for Cortex and GPC block
The imx5 pm code uses static mapping to access Cortex and GPC registers.
The patch create struct imx5_pm_data to encode physical address of
Cortex and GPC block, and create dynamic mapping for them at run-time.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 05:41:36 +0000 (13:41 +0800)]
ARM: imx5: reuse clock CCM mapping in pm code
The imx5 pm code needs to access CCM registers. Let's remove the use
of CCM static mapping in pm code by reusing the dynamic mapping created
in clock code.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 05:08:45 +0000 (13:08 +0800)]
ARM: imx5: use dynamic mapping for DPLL block
Replace the static mapping of DPLL block with dynamic mapping by
calling ioremap(). Ideally, this should be done by calling of_iomap(),
so that the physical address of DPLL can also be retrieved from device
tree. But unfortunately, DPLL blocks are not defined in DT in the first
place. So to maintain the compatibility of existing DTB, we use
ioremap() with physical address defines in the code.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 03:20:28 +0000 (11:20 +0800)]
ARM: imx5: use dynamic mapping for CCM block
Replace the static mapping of CCM block with dynamic mapping and
retrieve CCM base address from device tree. Though it's not nice to
encode the variable ccm_base in macros, it helps to avoid a massive
churn on the code.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Tue, 20 May 2014 02:23:50 +0000 (10:23 +0800)]
ARM: imx5: remove header crm-regs-imx5.h
Most of the macros in crm-regs-imx5.h are used nowhere. Let's move the
needed ones into the C files, and remove the header.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 14:23:43 +0000 (22:23 +0800)]
ARM: imx5: retrieve iim base from device tree
Instead of using static define and mapping, the patch changes imx5 code
that reads chip revision from IIM to retrieve base address from device
tree and use dynamic mapping.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 13:15:03 +0000 (21:15 +0800)]
ARM: imx5: call mxc_timer_init_dt() on imx51
Since i.MX51 supports DT only, it's more appropriate to call
mxc_timer_init_dt() than mxc_timer_init() to initialize timer.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 13:08:43 +0000 (21:08 +0800)]
ARM: imx5: remove function imx51_soc_init()
The function imx51_soc_init() was used by non-DT boot only. Since
i.MX51 supports DT only, the function can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 12:19:06 +0000 (20:19 +0800)]
ARM: imx5: tzic_init_irq() can directly be .init_irq hook
After i.MX51 supports DT only, tzic_init_irq() can figure out the
tzic_base on its own. Thus, it can directly be .init_irq hook, and
mx51[53]_init_irq() can be saved.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 07:47:32 +0000 (15:47 +0800)]
ARM: imx5: drop arguments from mx5_clocks_common_init()
The function mx5_clocks_common_init() was created with a number of
arguments to pass oscillator clock rate in non-DT boot. Since i.MX5
is DT only platform, the arguments can be dropped, and the clock rate
can just be retrieved from device tree.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 07:43:42 +0000 (15:43 +0800)]
ARM: imx5: make mx51_clocks_init() a DT call
Since i.MX51 becomes a DT only platform, we can make mx51_clocks_init()
a DT call and save function mx51_clocks_init_dt() now.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 06:19:11 +0000 (14:19 +0800)]
ARM: imx5: remove i.MX5 non-DT device registration helpers
i.MX5 is DT only platforms, so these non-DT device registration helpers
is used nowhere. Remove them.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 06:01:54 +0000 (14:01 +0800)]
ARM: imx5: remove imx51 non-DT support files
Since i.MX51 becomes a DT only platform, those non-DT support files can
be removed now.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 05:47:43 +0000 (13:47 +0800)]
ARM: imx5: drop option MACH_IMX51_DT
Since i.MX51 becomes DT only now, we can drop option MACH_IMX51_DT and
just use SOC_IMX51 instead. While at it, rename imx51-dt.c to
mach-imx51.c to align with the name schema of other IMX DT only
platforms.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 05:37:50 +0000 (13:37 +0800)]
ARM: imx5: move SOC_IMX5 and SOC_IMX51 into 'Device tree only'
After moving SOC_IMX51 support over to device tree, all i.MX5 support
becomes device tree only now. So options SOC_IMX5 and SOC_IMX51 can
just be under 'Device tree only'.
While at it, 'select ARCH_MXC_IOMUX_V3' is dropped, since it's only
needed by non-DT build before.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Mon, 19 May 2014 12:41:52 +0000 (20:41 +0800)]
ARM: imx: move EHCI platform defines out of platform_data header
The platform_data header usb-ehci-mxc.h has a lot of stuff used by only
IMX platform code. They shouldn't be really in this header but a IMX
platform local header. Create ehci.h and move these stuff into it.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Tue, 20 May 2014 16:43:51 +0000 (20:43 +0400)]
ARM: i.MX: Remove registration helper for i.MX1 USB UDC
imx_udc driver was removed from the kernel of about 10 months ago.
This patch removes a registration helper for this driver and
orphaned driver header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Tue, 20 May 2014 16:43:49 +0000 (20:43 +0400)]
ARM: i.MX1 clk: Add devicetree support
This patch adds devicetree support CCM module for i.MX1 (MC9328MX1) CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Paul Bolle [Fri, 16 May 2014 09:09:29 +0000 (11:09 +0200)]
ARM: imx: remove unused defines
None of the defines "for modules using static and dynamic DMA channels"
are used. Remove these.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Alexander Shiyan [Mon, 19 May 2014 05:21:17 +0000 (13:21 +0800)]
ARM: i.MX: Select HAVE_IMX_SRC for i.MX5 globally
No reason to choose a symbol HAVE_IMX_SRC separately for each supported
i.MX5 CPU, this patch selects this symbol globally for i.MX5.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo [Fri, 18 Jul 2014 08:09:07 +0000 (16:09 +0800)]
Merge tag 'imx-fixes-3.16-2' into imx/soc
The i.MX fixes for 3.16, 2nd take:
It fixes a hard machine hang regression for boards where only pcie is
active but no sata, as the latest imx6-pcie driver is no longer enabling
the upstream clock directly but only lvds clk out.
Lucas Stach [Thu, 17 Jul 2014 10:20:14 +0000 (12:20 +0200)]
ARM: clk-imx6q: parent lvds_sel input from upstream clock gates
The i.MX6 reference manual doesn't make a clear distinction
between the fixed clock divider and the enable gate for the
pcie and sata reference clocks. This lead to the lvds mux
inputs in the imx6q clk driver to be parented from the
ref clock (which is the divider) instead of the actual gate,
which in turn prevents the upstream clock to actually be
enabled when lvds clk out is active.
This fixes a hard machine hang regression in kernel 3.16 for
boards where only pcie is active but no sata, as with this
kernel version the imx6-pcie driver is no longer enabling
the upstream clock directly but only lvds clk out.
Reported-by: Arne Ruhnau <arne.ruhnau@target-sg.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Arne Ruhnau <arne.ruhnau@target-sg.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Linus Torvalds [Sun, 29 Jun 2014 21:11:36 +0000 (14:11 -0700)]
Linux 3.16-rc3
Linus Torvalds [Sun, 29 Jun 2014 20:40:08 +0000 (13:40 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
Randy Dunlap [Sat, 28 Jun 2014 01:28:56 +0000 (18:28 -0700)]
MAINTAINERS: exceptions for Documentation maintainer
Note that I don't maintain Documentation/ABI/,
Documentation/devicetree/, or the language translation files.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Sat, 28 Jun 2014 01:28:46 +0000 (18:28 -0700)]
Documentation: add section about git to email-clients.txt
These days most people use git to send patches so I have added a section
about that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Fri, 27 Jun 2014 16:01:47 +0000 (17:01 +0100)]
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.
This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Laura Abbott [Fri, 27 Jun 2014 09:17:27 +0000 (10:17 +0100)]
ARM: 8086/1: Set memblock limit for nommu
Commit
1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrea Adami [Wed, 25 Jun 2014 21:32:26 +0000 (22:32 +0100)]
ARM: 8085/1: sa1100: collie: add top boot mtd partition
The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrea Adami [Wed, 25 Jun 2014 21:31:15 +0000 (22:31 +0100)]
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
Reverts commit
d26b17edafc45187c30cae134a5e5429d58ad676
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.
Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Nicolas Pitre [Thu, 19 Jun 2014 21:57:01 +0000 (22:57 +0100)]
ARM: 8080/1: mcpm.h: remove unused variable declaration
The sync_phys variable has been replaced by link time computation in
mcpm_head.S before the code was submitted upstream.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thomas Petazzoni [Fri, 13 Jun 2014 09:58:38 +0000 (10:58 +0100)]
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Sat, 28 Jun 2014 18:32:32 +0000 (11:32 -0700)]
Merge tag 'spi-v3.16-rc2' of git://git./linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the biggest one being a fix for the newly
added Qualcomm SPI controller driver to make it not use its internal
chip select due to hardware bugs, replacing it with GPIOs"
* tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Remove chip select function
spi: qup: Fix order of spi_register_master
spi: sh-sci: fix use-after-free in sh_sci_spi_remove()
spi/pxa2xx: fix incorrect SW mode chipselect setting for BayTrail LPSS SPI
Linus Torvalds [Sat, 28 Jun 2014 18:31:58 +0000 (11:31 -0700)]
Merge tag 'regulator-v3.16-rc2' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Several driver specific fixes here, the palmas fixes being especially
important for a range of boards - the recent updates to support new
devices have introduced several regressions"
* tag 'regulator-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65218: Correct the the config register for LDO1
regulator: tps65218: Add the missing of_node assignment in probe
regulator: palmas: fix typo in enable_reg calculation
regulator: bcm590xx: fix vbus name
regulator: palmas: Fix SMPS enable/disable/is_enabled
Linus Torvalds [Sat, 28 Jun 2014 16:43:58 +0000 (09:43 -0700)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time around. The highlights include:
- iscsi-target CHAP authentication fixes to enforce explicit key
values (Tejas Vaykole + rahul.rane)
- fix a long-standing OOPs in target-core when a alua configfs
attribute is accessed after port symlink has been removed.
(Sebastian Herbszt)
- fix a v3.10.y iscsi-target regression causing the login reject
status class/detail to be ignored (Christoph Vu-Brugier)
- fix a v3.10.y iscsi-target regression to avoid rejecting an
existing ITT during Data-Out when data-direction is wrong (Santosh
Kulkarni + Arshad Hussain)
- fix a iscsi-target related shutdown deadlock on UP kernels (Mikulas
Patocka)
- fix a v3.16-rc1 build issue with vhost-scsi + !CONFIG_NET (MST)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: fix iscsit_del_np deadlock on unload
iovec: move memcpy_from/toiovecend to lib/iovec.c
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
iscsi-target: Explicily clear login response PDU in exception path
target: Fix left-over se_lun->lun_sep pointer OOPs
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
Mark Brown [Sat, 28 Jun 2014 13:01:23 +0000 (14:01 +0100)]
Merge remote-tracking branches 'spi/fix/pxa2xx', 'spi/fix/qup' and 'spi/fix/sh-sci' into spi-linus
Mark Brown [Sat, 28 Jun 2014 13:01:04 +0000 (14:01 +0100)]
Merge remote-tracking branches 'regulator/fix/bcm590xx', 'regulator/fix/palmas' and 'regulator/fix/tps65218' into regulator-linus
Mikulas Patocka [Mon, 23 Jun 2014 17:42:37 +0000 (13:42 -0400)]
iscsi-target: fix iscsit_del_np deadlock on unload
On uniprocessor preemptible kernel, target core deadlocks on unload. The
following events happen:
* iscsit_del_np is called
* it calls send_sig(SIGINT, np->np_thread, 1);
* the scheduler switches to the np_thread
* the np_thread is woken up, it sees that kthread_should_stop() returns
false, so it doesn't terminate
* the np_thread clears signals with flush_signals(current); and goes back
to sleep in iscsit_accept_np
* the scheduler switches back to iscsit_del_np
* iscsit_del_np calls kthread_stop(np->np_thread);
* the np_thread is waiting in iscsit_accept_np and it doesn't respond to
kthread_stop
The deadlock could be resolved if the administrator sends SIGINT signal to
the np_thread with killall -INT iscsi_np
The reproducible deadlock was introduced in commit
db6077fd0b7dd41dc6ff18329cec979379071f87, but the thread-stopping code was
racy even before.
This patch fixes the problem. Using kthread_should_stop to stop the
np_thread is unreliable, so we test np_thread_state instead. If
np_thread_state equals ISCSI_NP_THREAD_SHUTDOWN, the thread exits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Sat, 28 Jun 2014 02:00:45 +0000 (19:00 -0700)]
Merge tag 'iommu-fixes-v3.16-rc1' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- fix VT-d regression with handling multiple RMRR entries per device
- fix a small race that was left in the mmu_notifier handling in the
AMD IOMMUv2 driver
* tag 'iommu-fixes-v3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix small race between invalidate_range_end/start
iommu/vt-d: fix bug in handling multiple RMRRs for the same PCI device
Linus Torvalds [Sat, 28 Jun 2014 01:43:03 +0000 (18:43 -0700)]
Merge branch 'x86/urgent' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A pile of fixes related to the VDSO, EFI and 32-bit badsys handling.
It turns out that removing the section headers from the VDSO breaks
gdb, so this puts back most of them. A very simple typo broke
rt_sigreturn on some versions of glibc, with obviously disastrous
results. The rest is pretty much fixes for the corresponding fallout.
The EFI fixes fixes an arithmetic overflow on 32-bit systems and
quiets some build warnings.
Finally, when invoking an invalid system call number on x86-32, we
bypass a bunch of handling, which can make the audit code oops"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi-pstore: Fix an overflow on 32-bit builds
x86/vdso: Error out in vdso2c if DT_RELA is present
x86/vdso: Move DISABLE_BRANCH_PROFILING into the vdso makefile
x86_32, signal: Fix vdso rt_sigreturn
x86_32, entry: Do syscall exit work on badsys (CVE-2014-4508)
x86/vdso: Create .build-id links for unstripped vdso files
x86/vdso: Remove some redundant in-memory section headers
x86/vdso: Improve the fake section headers
x86/vdso2c: Use better macros for ELF bitness
x86/vdso: Discard the __bug_table section
efi: Fix compiler warnings (unused, const, type)
Linus Torvalds [Sat, 28 Jun 2014 01:37:56 +0000 (18:37 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"This is dominated by a large number of changes necessary for the MIPS
BPF code. code. Aside of that there are
- a fix for the MSC system controller support code.
- a Turbochannel fix.
- a recordmcount fix that's MIPS-specific.
- barrier fixes to smp-cps / pm-cps after unrelated changes elsewhere
in the kernel.
- revert support for MSA registers in the signal frames. The
reverted patch did modify the signal stack frame which of course is
inacceptable.
- fix math-emu build breakage with older compilers.
- some related cleanup.
- fix Lasat build error if CONFIG_CRC32 isn't set to y by the user"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (27 commits)
MIPS: Lasat: Fix build error if CRC32 is not enabled.
TC: Handle device_register() errors.
MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region
MIPS: bpf: Fix stack space allocation for BPF memwords on MIPS64
MIPS: BPF: Use 32 or 64-bit load instruction to load an address to register
MIPS: bpf: Fix PKT_TYPE case for big-endian cores
MIPS: BPF: Prevent kernel fall over for >=32bit shifts
MIPS: bpf: Drop update_on_xread and always initialize the X register
MIPS: bpf: Fix is_range() semantics
MIPS: bpf: Use pr_debug instead of pr_warn for unhandled opcodes
MIPS: bpf: Fix return values for VLAN_TAG_PRESENT case
MIPS: bpf: Use correct mask for VLAN_TAG case
MIPS: bpf: Fix branch conditional for BPF_J{GT/GE} cases
MIPS: bpf: Add SEEN_SKB to flags when looking for the PKT_TYPE
MIPS: bpf: Use 'andi' instead of 'and' for the VLAN cases
MIPS: bpf: Return error code if the offset is a negative number
MIPS: bpf: Use the LO register to get division's quotient
MIPS: mm: uasm: Fix lh micro-assembler instruction
MIPS: uasm: Add SLT uasm instruction
MIPS: uasm: Add s3s1s2 instruction builder
...
Linus Torvalds [Sat, 28 Jun 2014 01:36:50 +0000 (18:36 -0700)]
Merge tag 'arc-fixes-for-3.16' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Some SMP changes, a ptrace request for NPTL debugging, bunch of build
breakages/warnings"
* tag 'arc-fixes-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [SMP] Enable icache coherency
ARC: [SMP] Fix IPI IRQ registration
ARC: Implement ptrace(PTRACE_GET_THREAD_AREA)
ARC: optimize kernel bss clearing in early boot code
ARC: Fix build breakage for !CONFIG_ARC_DW2_UNWIND
ARC: fix build warning in devtree
ARC: remove checks for CONFIG_ARC_MMU_V4
Linus Torvalds [Sat, 28 Jun 2014 01:33:49 +0000 (18:33 -0700)]
Merge tag 'compress-3.16-rc3' of git://git./linux/kernel/git/gregkh/driver-core
Pull compress bugfix from Greg KH:
"Here is another lz4 bugfix for 3.16-rc3 that resolves a reported issue
with that compression algorithm"
* tag 'compress-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lz4: fix another possible overrun
Linus Torvalds [Sat, 28 Jun 2014 01:04:22 +0000 (18:04 -0700)]
Merge tag 'stable/for-linus-3.16-rc1-tag' of git://git./linux/kernel/git/konrad/swiotlb
Pull swiotlb bugfix from Konrad Rzeszutek Wilk:
"One bug-fix that had been in tree for quite some time. We had assumed
that the physical address zero was invalid and would fail it. But
that is not true and on some architectures it is not reserved and
valid. This fixes it"
* tag 'stable/for-linus-3.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: don't assume PA 0 is invalid
Linus Torvalds [Sat, 28 Jun 2014 00:21:36 +0000 (17:21 -0700)]
Merge tag 'sound-3.16-rc3' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here includes a few patchset for fixing mostly HD-audio issues in
addition to a patch assuring the compress API bytes alignment and a
fix for the die-hard existing race condition at USB-audio
disconnection. The volume looks big in Realtek HD-audio code, but
it's just a translation of the fixup tables, and the actual changes
are rather trivial"
* tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N values when resuming HSW/BDW display controller
ALSA: usb-audio: Fix races at disconnection and PCM closing
ALSA: hda - Adjust speaker HPF and add LED support for HP Spectre 13
ALSA: hda - Make the pin quirk tables use the SND_HDA_PIN_QUIRK macro
ALSA: hda - Make a SND_HDA_PIN_QUIRK macro
ALSA: hda - Add pin quirk for Dell XPS 15
ALSA: hda - hdmi: call overridden init on resume
ALSA: hda - Fix usage of "model" module parameter
ALSA: compress: fix the struct alignment to 4 bytes
Linus Torvalds [Sat, 28 Jun 2014 00:20:48 +0000 (17:20 -0700)]
Merge tag 'mfd-fixes-3.16' of git://git./linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Couple of simple fixes due for the v3.16 -rcs"
* tag 'mfd-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: ab8500: Fix dt irq mapping
mfd: davinci: Voicecodec needs regmap_mmio
mfd: STw481x: Allow modular build
mfd: UCB1x00: Enable modular build
This page took 0.046247 seconds and 5 git commands to generate.