Lv Zheng [Thu, 11 Jun 2015 05:21:23 +0000 (13:21 +0800)]
ACPI / EC: Cleanup transaction state transition.
This patch collects transaction state transition code into one function. We
then could have a single function to maintain transaction transition
related behaviors. No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Tigran Gabrielyan <tigrangab@gmail.com>
Tested-by: Adrien D <ghbdtn@openmailbox.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Fri, 15 May 2015 06:37:11 +0000 (14:37 +0800)]
ACPI / EC: Remove non-root-caused busy polling quirks.
{ Update to correct 1 patch subject in the description }
We have fixed a lot of race issues in the EC driver recently.
The following commit introduces MSI udelay()/msleep() quirk to MSI laptops
to make EC firmware working for bug 12011 without root causing any EC
driver race issues:
Commit:
5423a0cb3f74c16e90683f8ee1cec6c240a9556e
Subject: ACPI: EC: Add delay for slow MSI controller
Commit:
34ff4dbccccce54c83b1234d39b7ad9e548a75dd
Subject: ACPI: EC: Separate delays for MSI hardware
The following commit extends ECDT validation quirk to MSI laptops to make
EC driver locating EC registers properly for bug 12461:
Commit:
a5032bfdd9c80e0231a6324661e123818eb46ecd
Subject: ACPI: EC: Always parse EC device
This is a different quirk than the MSI udelay()/msleep() quirk. This patch
keeps validating ECDT for only "Micro-Star MS-171F" as reported.
The following commit extends MSI udelay()/msleep() quirk to Quanta laptops
to make EC firmware working for bug 20242, there is no requirement to
validate ECDT for Quanta laptops:
Commit:
534bc4e3d27096e2f3fc00c14a20efd597837a4f Mon Sep 17 00:00:00 2001
Subject: ACPI EC: enable MSI workaround for Quanta laptops
The following commit extends MSI udelay()/msleep() quirk to Clevo laptops
to make EC firmware working for bug 77431, there is no requirement to
validate ECDT for Clevo laptops:
Commit:
777cb382958851c88763253fe00a26529be4c0e9
Subject: ACPI / EC: Add msi quirk for Clevo W350etq
All udelay()/msleep() quirks for MSI/Quanta/Clevo seem to be the wrong
fixes generated without fixing the EC driver race issues.
And even if it is not wrong, the guarding can be covered by the following
commits in wait polling mode:
Commit:
9e295ac14d6a59180beed0735e6a504c2ee87761
Subject: ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
Commit: commit in the same series
Subject: ACPI / EC: Fix and clean up register access guarding logics.
The only case that is not covered is the inter-transaction guarding. And
there is no evidence that we need the inter-transaction guarding upon
reading the noted bug entries.
So it is time to remove the quirks and let the users to try again. If there
is a regression, the only thing we need to do is to restore the
inter-transaction guarding for the reported platforms.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=12011
Link: https://bugzilla.kernel.org/show_bug.cgi?id=12461
Link: https://bugzilla.kernel.org/show_bug.cgi?id=20242
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Fri, 15 May 2015 06:16:48 +0000 (14:16 +0800)]
ACPI / EC: Add module params for polling modes.
We have 2 polling modes in the EC driver:
1. busy polling: originally used for the MSI quirks. udelay() is used to
perform register access guarding.
2. wait polling: normal code path uses wait_event_timeout() and it can be
woken up as soon as the transaction is completed in the interrupt mode.
It also contains the register acces guarding logic in case the interrupt
doesn't arrive and the EC driver is about to advance the transaction in
task context (the polling mode).
The wait polling is useful for interrupt mode to allow other tasks to use
the CPU during the wait.
But for the polling mode, the busy polling takes less time than the wait
polling, because if no interrupt arrives, the wait polling has to wait the
minimal HZ interval.
We have a new use case for using the busy polling mode. Some GPIO drivers
initialize PIN configuration which cause a GPIO multiplexed EC GPE to be
disabled out of the GPE register's control. Busy polling mode is useful
here as it takes less time than the wait polling. But the guarding logic
prevents it from responding even faster. We should spinning around the EC
status rather than spinning around the nop execution lasted a determined
period.
This patch introduces 2 module params for the polling mode switch and the
guard time, so that users can use the busy polling mode without the
guarding in case the guarding is not necessary. This is an example to use
the 2 module params for this purpose:
acpi.ec_busy_polling acpi.ec_polling_guard=0
We've tested the patch on a test platform. The platform suffers from such
kind of the GPIO PIN issue. The GPIO driver resets all PIN configuration
and after that, EC interrupt cannot arrive because of the multiplexing.
Then the platform suffers from a long delay carried out by the
wait_event_timeout() as all further EC transactions will run in the polling
mode. We switched the EC driver to use the busy polling mechanism instead
of the wait timeout polling mechanism and the delay is still high:
[ 44.283005] calling PNP0C0B:00+ @ 1305, parent: platform
[ 44.417548] call PNP0C0B:00+ returned 0 after 131323 usecs
And this patch can significantly reduce the delay:
[ 44.502625] calling PNP0C0B:00+ @ 1308, parent: platform
[ 44.503760] call PNP0C0B:00+ returned 0 after 1103 usecs
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Fri, 15 May 2015 06:16:42 +0000 (14:16 +0800)]
ACPI / EC: Fix and clean up register access guarding logics.
In the polling mode, EC driver shouldn't access the EC registers too
frequently. Though this statement is concluded from the non-root caused
bugs (see links below), we've maintained the register access guarding
logics in the current EC driver. The guarding logics can be found here and
there, makes it hard to root cause real timing issues. This patch collects
the guarding logics into one single function so that all hidden logics
related to this can be seen clearly.
The current guarding related code also has several issues:
1. Per-transaction timestamp prevents inter-transaction guarding from being
implemented in the same place. We have an inter-transaction udelay() in
acpi_ec_transaction_unblocked(), this logic can be merged into ec_poll()
if we can use per-device timestamp. This patch completes such merge to
form a new ec_guard() function and collects all guarding related hidden
logics in it.
One hidden logic is: there is no inter-transaction guarding performed
for non MSI quirk (wait polling mode), this patch skips
inter-transaction guarding before wait_event_timeout() for the wait
polling mode to reveal the hidden logic.
The other hidden logic is: there is msleep() inter-transaction guarding
performed when the GPE storming is observed. As after merging this
commit:
Commit:
e1d4d90fc0313d3d58cbd7912c90f8ef24df45ff
Subject: ACPI / EC: Refine command storm prevention support
EC_FLAGS_COMMAND_STORM is ensured to be cleared after invoking
acpi_ec_transaction_unlocked(), the msleep() guard logic will never
happen now. Since no one complains such change, this logic is likely
added during the old times where the EC race issues are not fixed and
the bugs are false root-caused to the timing issue. This patch simply
removes the out-dated logic. We can restore it by stop skipping
inter-transaction guarding for wait polling mode.
Two different delay values are defined for msleep() and udelay() while
they are merged in this patch to 550us.
2. time_after() causes additional delay in the polling mode (can only be
observed in noirq suspend/resume processes where polling mode is always
used) before advance_transaction() is invoked ("wait polling" log is
added before wait_event_timeout()). We can see 2 wait_event_timeout()
invocations. This is because time_after() ensures a ">" validation while
we only need a ">=" validation here:
[ 86.739909] ACPI: Waking up from system sleep state S3
[ 86.742857] ACPI : EC: 2: Increase command
[ 86.742859] ACPI : EC: ***** Command(RD_EC) started *****
[ 86.742861] ACPI : EC: ===== TASK (0) =====
[ 86.742871] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 86.742873] ACPI : EC: EC_SC(W) = 0x80
[ 86.742876] ACPI : EC: ***** Event started *****
[ 86.742880] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.743972] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.747966] ACPI : EC: ===== TASK (0) =====
[ 86.747977] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 86.747978] ACPI : EC: EC_DATA(W) = 0x06
[ 86.747981] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.751971] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.755969] ACPI : EC: ===== TASK (0) =====
[ 86.755991] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
[ 86.755993] ACPI : EC: EC_DATA(R) = 0x03
[ 86.755994] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 86.755995] ACPI : EC: ***** Command(RD_EC) stopped *****
[ 86.755996] ACPI : EC: 1: Decrease command
This patch corrects this by using time_before() instead in ec_guard():
[ 54.283146] ACPI: Waking up from system sleep state S3
[ 54.285414] ACPI : EC: 2: Increase command
[ 54.285415] ACPI : EC: ***** Command(RD_EC) started *****
[ 54.285416] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.285417] ACPI : EC: ===== TASK (0) =====
[ 54.285424] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 54.285425] ACPI : EC: EC_SC(W) = 0x80
[ 54.285427] ACPI : EC: ***** Event started *****
[ 54.285429] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.287209] ACPI : EC: ===== TASK (0) =====
[ 54.287218] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
[ 54.287219] ACPI : EC: EC_DATA(W) = 0x06
[ 54.287222] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.291190] ACPI : EC: ===== TASK (0) =====
[ 54.291210] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
[ 54.291213] ACPI : EC: EC_DATA(R) = 0x03
[ 54.291214] ACPI : EC: ~~~~~ wait polling ~~~~~
[ 54.291215] ACPI : EC: ***** Command(RD_EC) stopped *****
[ 54.291216] ACPI : EC: 1: Decrease command
After cleaning up all guarding logics, we have one single function
ec_guard() collecting all old, non-root-caused, hidden logics. Then we can
easily tune the logics in one place to respond to the bug reports.
Except the time_before() change, all other changes do not change the
behavior of the EC driver.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=12011
Link: https://bugzilla.kernel.org/show_bug.cgi?id=20242
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Fri, 15 May 2015 06:16:34 +0000 (14:16 +0800)]
ACPI / EC: Remove irqs_disabled() check.
The following commit merges polling and interrupt modes for EC driver:
Commit:
2a84cb9852f52c0cd1c48bca41a8792d44ad06cc Mon Sep 17 00:00:00 2001
Subject: ACPI: EC: Merge IRQ and POLL modes
The irqs_disabled() check introduced in it tries to fall into busy polling
mode when the context of ec_poll() cannot sleep.
Actually ec_poll() is ensured to be invoked in the contexts that can sleep
(from a sysfs /sys/kernel/debug/ec/ec0/io access, or from
acpi_evaluate_object(), or from acpi_ec_gpe_poller()). Without the MSI
quirk, we never saw the udelay() logic invoked. Thus this check is useless
and can be removed.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Fri, 15 May 2015 06:16:27 +0000 (14:16 +0800)]
ACPI / EC: Remove storming threashold enlarging quirk.
This patch removes the storming threashold enlarging quirk.
After applying the following commit, we can notice that there is no no-op
GPE handling invocation can be observed, thus it is unlikely that the
no-op counts can exceed the storming threashold:
Commit:
ca37bfdfbc8d0a3ec73e4b97bb26dcfa51d515aa
Subject: ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
Even when the storming happens, we have already limited its affection to
the only transaction and no further transactions will be affected. This is
done by this commit:
Commit:
e1d4d90fc0313d3d58cbd7912c90f8ef24df45ff
Subject: ACPI / EC: Refine command storm prevention support
So it's time to remove this quirk.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=45151
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Fri, 15 May 2015 06:16:17 +0000 (14:16 +0800)]
ACPI / EC: Update acpi_ec_is_gpe_raised() with new GPE status flag.
This patch updates acpi_ec_is_gpe_raised() according to the following
commit:
Commit:
09af8e8290deaff821ced01ea83594ee4c21e8df
Subject: ACPICA: Events: Add support to return both enable/status register values for GPE and fixed event.
This is actually a no-op change as both the flags are defined to a same
value.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Thu, 14 May 2015 22:31:23 +0000 (00:31 +0200)]
Merge branches 'acpi-init' and 'acpica'
* acpi-init:
ACPI / init: Fix the ordering of acpi_reserve_resources()
* acpica:
Revert "ACPICA: Permanently set _REV to the value '2'."
Rafael J. Wysocki [Tue, 12 May 2015 22:44:14 +0000 (00:44 +0200)]
Revert "ACPICA: Permanently set _REV to the value '2'."
Revert commit
b1ef29725865 (ACPICA: Permanently set _REV to the value
'2'.) as it causes a sound regression to happen on Dell XPS 13 (2015).
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Sun, 10 May 2015 22:12:29 +0000 (15:12 -0700)]
Linux 4.1-rc3
Linus Torvalds [Sun, 10 May 2015 21:58:53 +0000 (14:58 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I really need to get back to sending these on my Friday, instead of my
Monday morning, but nothing too amazing in here: a few amdkfd fixes, a
few radeon fixes, i915 fixes, one tegra fix and one core fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
drm/radeon: make UVD handle checking more strict
drm/radeon: make VCE handle check more strict
drm/radeon: fix userptr lockup
drm/radeon: fix userptr BO unpin bug v3
drm/amdkfd: Initialize sdma vm when creating sdma queue
drm/amdkfd: Don't report local memory size
drm/amdkfd: allow unregister process with queues
drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
drm/i915: Sink rate read should be saved in deca-kHz
drm/i915/dp: there is no audio on port A
drm/i915: Add missing MacBook Pro models with dual channel LVDS
drm/i915: Assume dual channel LVDS if pixel clock necessitates it
drm/radeon: don't setup audio on asics that don't support it
drm/radeon: disable semaphores for UVD V1 (v2)
Dave Airlie [Sun, 10 May 2015 20:06:22 +0000 (06:06 +1000)]
Merge tag 'drm-intel-fixes-2015-05-08' of git://anongit.freedesktop.org/drm-intel into drm-fixes
misc i915 fixes.
* tag 'drm-intel-fixes-2015-05-08' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
drm/i915: Sink rate read should be saved in deca-kHz
drm/i915/dp: there is no audio on port A
drm/i915: Add missing MacBook Pro models with dual channel LVDS
drm/i915: Assume dual channel LVDS if pixel clock necessitates it
Mario Kleiner [Tue, 7 Apr 2015 04:31:09 +0000 (06:31 +0200)]
drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
Since commit
844b03f27739135fe1fed2fef06da0ffc4c7a081 we make
sure that after vblank irq off, we return the last valid
(vblank count, vblank timestamp) pair to clients, e.g., during
modesets, which is good.
An overlooked side effect of that commit for kms drivers without
support for precise vblank timestamping is that at vblank irq
enable, when we update the vblank counter from the hw counter, we
can't update the corresponding vblank timestamp, so now we have a
totally mismatched timestamp for the new count to confuse clients.
Restore old client visible behaviour from before Linux 3.17, but
zero out the timestamp at vblank counter update (instead of disable
as in original implementation) if we can't generate a meaningful
timestamp immediately for the new vblank counter. This will fix
this regression, so callers know they need to retry again later
if they need a valid timestamp, but at the same time preserves
the improvements made in the commit mentioned above.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> #v3.17+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Sun, 10 May 2015 18:16:48 +0000 (11:16 -0700)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A set of ARM fixes:
- fix an off-by-one error in the iommu DMA ops, which caused errors
with a 4GiB size.
- remove comments mentioning the non-existent CONFIG_CPU_ARM1020_CPU_IDLE
macro.
- remove useless CONFIG_CPU_ICACHE_STREAMING_DISABLE blocks, where
this symbol never appeared in any Kconfig.
- fix Feroceon code to cope with a previous change correctly (it
incorrectly left an additional word in an assembly structure
definition)
- avoid a misleading IRQ affinity warning in the ARM PMU code for
IRQs which are already affine to their CPUs.
- fix the node name printed in the IRQ affinity warning"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8352/1: perf: Fix the pmu node name in warning message
ARM: 8351/1: perf: don't warn about missing interrupt-affinity property for PPIs
ARM: 8350/1: proc-feroceon: Fix feroceon_proc_info macro
ARM: 8349/1: arch/arm/mm/proc-arm925.S: remove dead #ifdef block
ARM: 8348/1: remove comments on CPU_ARM1020_CPU_IDLE
ARM: 8347/1: dma-mapping: fix off-by-one check in arm_setup_iommu_dma_ops
Linus Torvalds [Sun, 10 May 2015 18:13:19 +0000 (11:13 -0700)]
Merge tag 'samsung-fixes-1' of git://git./linux/kernel/git/kgene/linux-samsung
Pull samsung fixes from Kukjin Kim:
"Here is Samsung fixes for v4.1. Since I've missed to send this via
arm-soc tree before v4.1-rc3, so I'm sending this to you directly
- fix commit
ea08de16eb1b ("ARM: dts: Add DISP1 power domain for
exynos5420") which causes 'unhandled fault: imprecise external
abort' error when PD turned off. ("make DP a consumer of DISP1
power domain")
- fix 's3c-rtc' probe failure on Odriod-X2/U2/U3 boards ("add
'rtc_src' clock to rtc node for source clock of rtc")
- fix typo for 'cpu-crit-0' trip point on exynos5420/5440
- fix S2R failure on exynos5250-snow due to card power of Marvell
WiFi driver (suspend/resume) ("add keep-power-in-susped to WiFi
SDIO node")"
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
Linus Torvalds [Sat, 9 May 2015 23:13:38 +0000 (16:13 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few patches have come up since the merge window. The largest one is
a rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1 is now
listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
MAINTAINERS: Update brcmstb entry
MAINTAINERS: Remove Christian Daudt for mach-bcm
...
Linus Torvalds [Sat, 9 May 2015 23:07:14 +0000 (16:07 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull user-namespace fix from Eric Biederman:
"Eric Windish recently reported a really bug that allows mounting fresh
copies of proc and sysfs when it really should not be allowed. The
code attempted to verify that proc and sysfs were fully visible but
there is a test missing to ensure that the root of the filesystem is
visible. Doh!
The following patch fixes that.
This fixes a containment issue that the docker folks are seeing"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
mnt: Fix fs_fully_visible to verify the root directory is visible
Linus Torvalds [Sat, 9 May 2015 21:59:05 +0000 (14:59 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Two patches from the irq departement:
- a simple fix to make dummy_irq_chip usable for wakeup scenarios
- removal of the gic arch_extn hackery. Now that all users are
converted we really want to get rid of the interface so people wont
come up with new use cases"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: gic: Drop support for gic_arch_extn
genirq: Set IRQCHIP_SKIP_SET_WAKE flag for dummy_irq_chip
Linus Torvalds [Sat, 9 May 2015 21:57:49 +0000 (14:57 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A simple fix to actually shut down a detached device instead of
keeping it active"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents: Shutdown detached clockevent device
Rusty Russell [Fri, 8 May 2015 18:09:52 +0000 (03:39 +0930)]
m32r: make flush_cpumask non-volatile.
We cast away the volatile, but really, why make it volatile at all?
We already do a mb() inside the cpumask_empty() loop.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric W. Biederman [Fri, 8 May 2015 21:36:50 +0000 (16:36 -0500)]
mnt: Fix fs_fully_visible to verify the root directory is visible
This fixes a dumb bug in fs_fully_visible that allows proc or sys to
be mounted if there is a bind mount of part of /proc/ or /sys/ visible.
Cc: stable@vger.kernel.org
Reported-by: Eric Windisch <ewindisch@docker.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Linus Torvalds [Sat, 9 May 2015 04:39:12 +0000 (21:39 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes for bugs caught while digging in fs/namei.c. The
first one is this cycle regression, the second is 3.11 and later"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
path_openat(): fix double fput()
namei: d_is_negative() should be checked before ->d_seq validation
Al Viro [Sat, 9 May 2015 02:53:15 +0000 (22:53 -0400)]
path_openat(): fix double fput()
path_openat() jumps to the wrong place after do_tmpfile() - it has
already done path_cleanup() (as part of path_lookupat() called by
do_tmpfile()), so doing that again can lead to double fput().
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Thu, 7 May 2015 23:24:57 +0000 (19:24 -0400)]
namei: d_is_negative() should be checked before ->d_seq validation
Fetching ->d_inode, verifying ->d_seq and finding d_is_negative() to
be true does *not* mean that inode we'd fetched had been NULL - that
holds only while ->d_seq is still unchanged.
Shift d_is_negative() checks into lookup_fast() prior to ->d_seq
verification.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 9 May 2015 03:59:02 +0000 (20:59 -0700)]
Merge branch 'for-linus-4.1' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"When an arm user reported crashes near page_address(page) in my new
code, it became clear that I can't be trusted with GFP masks. Filipe
beat me to the patch, and I'll just be in the corner with my dunce cap
on"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong mapping flags for free space inode
Linus Torvalds [Sat, 9 May 2015 03:38:21 +0000 (20:38 -0700)]
Merge tag 'dm-4.1-fixes-2' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two additional fixes for changes introduced via DM during the 4.1
merge window.
The first reverts a dm-crypt change that wasn't correct. The second
fixes a device format regression that impacted userspace"
* tag 'dm-4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
init: fix regression by supporting devices with major:minor:offset format
Revert "dm crypt: fix deadlock when async crypto algorithm returns -EBUSY"
Linus Torvalds [Sat, 9 May 2015 02:49:35 +0000 (19:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes since the merge window;
- fix for a double elevator module release, from Chao Yu. Ancient bug.
- the splice() MORE flag fix from Christophe Leroy.
- a fix for NVMe, fixing a patch that went in in the merge window.
From Keith.
- two fixes for blk-mq CPU hotplug handling, from Ming Lei.
- bdi vs blockdev lifetime fix from Neil Brown, fixing and oops in md.
- two blk-mq fixes from Shaohua, fixing a race on queue stop and a
bad merge issue with FUA writes.
- division-by-zero fix for writeback from Tejun.
- a block bounce page accounting fix, making sure we inc/dec after
bouncing so that pre/post IO pages match up. From Wang YanQing"
* 'for-linus' of git://git.kernel.dk/linux-block:
splice: sendfile() at once fails for big files
blk-mq: don't lose requests if a stopped queue restarts
blk-mq: fix FUA request hang
block: destroy bdi before blockdev is unregistered.
block:bounce: fix call inc_|dec_zone_page_state on different pages confuse value of NR_BOUNCE
elevator: fix double release of elevator module
writeback: use |1 instead of +1 to protect against div by zero
blk-mq: fix CPU hotplug handling
blk-mq: fix race between timeout and CPU hotplug
NVMe: Fix VPD B0 max sectors translation
Linus Torvalds [Sat, 9 May 2015 02:42:59 +0000 (19:42 -0700)]
Merge tag 'gpio-v4.1-2' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a bunch of GPIO fixes that I collected since -rc1, nothing
controversial, nothing special:
- fix a memory leak for GPIO hotplug.
- fix a signedness bug in the ACPI GPIO pin validation.
- driver fixes: Qualcomm SPMI and OMAP MPUIO IRQ issues"
* tag 'gpio-v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: omap: Fix regression for MPUIO interrupts
gpio: sysfs: fix memory leaks and device hotplug
pinctrl: qcom-spmi-gpio: Fix input value report
pinctrl: qcom-spmi-gpio: Fix output type configuration
gpiolib: change gpio pin from unsigned to signed in acpi callback
Linus Torvalds [Sat, 9 May 2015 02:34:35 +0000 (19:34 -0700)]
Merge tag 'mmc-4.1-rc2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Don't access RPMB partitions for normal read/write
- Fix hibernation restore sequence
MMC host:
- dw_mmc: Fix card detection for non removable cards
- dw_mmc: Fix sglist issue in 32-bit mode
- sh_mmcif: Fix timeout value for command request"
* tag 'mmc-4.1-rc2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
mmc: dw_mmc: init desc in dw_mci_idmac_init
mmc: card: Don't access RPMB partitions for normal read/write
mmc: sh_mmcif: Fix timeout value for command request
mmc: core: add missing pm event in mmc_pm_notify to fix hib restore
Linus Torvalds [Sat, 9 May 2015 01:22:05 +0000 (18:22 -0700)]
Merge tag 'trace-fixes-v4.1-rc2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"The newly added ftrace_print_array_seq() function had a bug in it.
Luckily, the only user of it didn't make the 4.1 merge window.
But the helper function should be fixed before 4.2 when the users
start coming in"
* tag 'trace-fixes-v4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make ftrace_print_array_seq compute buf_len
Javier Martinez Canillas [Fri, 8 May 2015 18:15:16 +0000 (03:15 +0900)]
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Abhilash Kesavan [Fri, 8 May 2015 18:11:21 +0000 (03:11 +0900)]
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
Remove the extra zero in the "cpu-crit-0" trip point for exynos5420
and exynos5440.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Markus Reichl [Fri, 8 May 2015 18:05:51 +0000 (03:05 +0900)]
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Javier Martinez Canillas [Fri, 8 May 2015 17:33:42 +0000 (02:33 +0900)]
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
Commit
ea08de16eb1b ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.
This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.
Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.
Fixes: ea08de16eb1b ("ARM: dts: Add DISP1 power domain for exynos5420")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Baruch Siach [Tue, 28 Apr 2015 10:59:43 +0000 (13:59 +0300)]
MAINTAINERS: add Conexant Digicolor machines entry
This adds Baruch as the maintainer for the Digicolor platform.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Dinh Nguyen [Mon, 20 Apr 2015 19:13:12 +0000 (14:13 -0500)]
MAINTAINERS: socfpga: update the git repo for SoCFPGA
The git tree at rocketboards.org is going away. Update the entry to reflect
the address of the new location. Also add an entry for all the socfpga_*
dts files.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mario Kleiner [Mon, 4 May 2015 04:29:44 +0000 (06:29 +0200)]
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
Tegra would not only need a hardware vblank counter that
increments at leading edge of vblank, but also support
for instantaneous high precision vblank timestamp queries, ie.
a proper implementation of dev->driver->get_vblank_timestamp().
Without these, there can be off-by-one errors during vblank
disable/enable if the scanout is inside vblank at en/disable
time, and additionally clients will never see any useable
vblank timestamps when querying via drmWaitVblank ioctl. This
would negatively affect swap scheduling under X11 and Wayland.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 8 May 2015 10:52:51 +0000 (20:52 +1000)]
Merge tag 'drm-amdkfd-fixes-2015-05-07' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes
- Add missing initialization of SDMA vm register when creating an SDMA queue
- Don't report local memory size, as we don't support local memory allocation
yet.
- Allow to unregister process with exisiting queues. Until now we blocked
it with BUG_ON, which was also an error by itself.
* tag 'drm-amdkfd-fixes-2015-05-07' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Initialize sdma vm when creating sdma queue
drm/amdkfd: Don't report local memory size
drm/amdkfd: allow unregister process with queues
Dave Airlie [Fri, 8 May 2015 10:52:21 +0000 (20:52 +1000)]
Merge branch 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Mostly stability fixes for UVD and VCE, plus a few other bug and regression
fixes.
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
drm/radeon: make UVD handle checking more strict
drm/radeon: make VCE handle check more strict
drm/radeon: fix userptr lockup
drm/radeon: fix userptr BO unpin bug v3
drm/radeon: don't setup audio on asics that don't support it
drm/radeon: disable semaphores for UVD V1 (v2)
Zhangfei Gao [Tue, 5 May 2015 08:54:49 +0000 (16:54 +0800)]
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
When non-removable is used for emmc, MMC_CAP_NONREMOVABLE should
also be checked, otherwise detection fail since present=0
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Zhangfei Gao [Thu, 30 Apr 2015 14:16:28 +0000 (22:16 +0800)]
mmc: dw_mmc: init desc in dw_mci_idmac_init
Set 0 to des1 in 32bit case.
Otherwise the random value of des1 will be used in
dw_mci_translate_sglist: IDMAC_SET_BUFFER1_SIZE(desc, length)
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds [Thu, 7 May 2015 22:58:00 +0000 (15:58 -0700)]
Merge tag 'pm+acpi-4.1-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These include three regression fixes (PCI resources management,
ACPI/PNP device enumeration, ACPI SBS on MacBook) and two ACPI
documentation fixes related to GPIO.
Specifics:
- Fix for a PCI resources management regression introduced during the
4.0 cycle and related to the handling of ACPI resources'
Producer/Consumer flags that turn out to be useless (Jiang Liu)
- Fix for a MacBook regression related to the Smart Battery Subsystem
(SBS) driver causing various problems (stalls on boot, failure to
detect or report battery) to happen and introduced during the 3.18
cycle (Chris Bainbridge)
- Fix for an ACPI/PNP device enumeration regression introduced during
the 3.16 cycle caused by failing to include two PNP device IDs into
the list of IDs that PNP device objects need to be created for
(Witold Szczeponik)
- Fixes for two minor mistakes in the ACPI GPIO properties
documentation (Antonio Ospite, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
Rafael J. Wysocki [Thu, 7 May 2015 19:24:34 +0000 (21:24 +0200)]
Merge branches 'acpi-resources', 'acpi-battery', 'acpi-doc' and 'acpi-pnp'
* acpi-resources:
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-battery:
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
* acpi-doc:
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
* acpi-pnp:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
Rafael J. Wysocki [Thu, 7 May 2015 19:19:39 +0000 (21:19 +0200)]
ACPI / init: Fix the ordering of acpi_reserve_resources()
Since acpi_reserve_resources() is defined as a device_initcall(),
there's no guarantee that it will be executed in the right order
with respect to the rest of the ACPI initialization code. On some
systems this leads to breakage if, for example, the address range
that should be reserved for the ACPI fixed registers is given to
the PCI host bridge instead if the race is won by the wrong code
path.
Fix this by turning acpi_reserve_resources() into a void function
and calling it directly from within the ACPI initialization sequence.
Reported-and-tested-by: George McCollister <george.mccollister@gmail.com>
Link: http://marc.info/?t=143092384600002&r=1&w=2
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 7 May 2015 18:18:34 +0000 (11:18 -0700)]
Merge tag 'for-f2fs-4.1-rc3' of git://git./linux/kernel/git/jaegeuk/f2fs
Pull f2fs fixes from Jaegeuk Kim:
"Fix a performance regression and a bug"
* tag 'for-f2fs-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: fix wrong error hanlder in f2fs_follow_link
Revert "f2fs: enhance multi-threads performance"
Fabio Estevam [Tue, 5 May 2015 17:35:49 +0000 (14:35 -0300)]
ARM: multi_v7_defconfig: Select more FSL SoCs
Select IMX50, IMX6SX and LS1021A SoC support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Nicolas Ferre [Wed, 29 Apr 2015 09:57:18 +0000 (11:57 +0200)]
MAINTAINERS: replace an AT91 maintainer
As some help is needed from an active maintainer, replace Andrew Victor
by Alexandre Belloni in the ARM/Atmel MAINTAINERS' entry (aka AT91).
Add an entry to the CREDITS file.
Thanks Andrew for the great role you played during the early days of this
product family.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mark Salter [Tue, 28 Apr 2015 17:09:32 +0000 (13:09 -0400)]
drivers: CCI: fix used_mask init in validate_group()
Currently in validate_group(), there is a static initializer
for fake_pmu.used_mask which is based on CPU_BITS_NONE but
the used_mask array size is based on CCI_PMU_MAX_HW_EVENTS.
CCI_PMU_MAX_HW_EVENTS is not based on NR_CPUS, so CPU_BITS_NONE
is not correct and will cause a build failure if NR_CPUS
is set high enough to make CPU_BITS_NONE larger than used_mask.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 7 May 2015 16:28:04 +0000 (18:28 +0200)]
Merge tag 'stericsson-fixes-v4.1' of git://git./linux/kernel/git/linusw/linux-stericsson into fixes
Merge "Ux500 fixes" from Linus Walleij:
This fixes an MMC/SD configuration issue present for some time
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
* tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable GPIO regulator for SD-card for snowball
ARM: ux500: Enable GPIO regulator for SD-card for HREF boards
ARM: ux500: Move GPIO regulator for SD-card into board DTSs
Arnd Bergmann [Thu, 7 May 2015 16:26:48 +0000 (18:26 +0200)]
Merge tag 'renesas-fixes-for-v4.1' of git://git./linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.1" from Simon Horman:
* Fix adv7511 IRQ sensing on koelsch board
* tag 'renesas-fixes-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: koelsch: Fix adv7511 IRQ sensing
Arnd Bergmann [Thu, 7 May 2015 16:25:38 +0000 (18:25 +0200)]
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
Arnd Bergmann [Thu, 7 May 2015 16:24:32 +0000 (18:24 +0200)]
Merge tag 'arm-soc/for-4.1/maintainers' of github.com/broadcom/stblinux into fixes
Merge "MAINTAINERS update for Broadcom SoCs for 4.1 #2" from Florian Fainelli:
This pull request contains 3 changes to the MAINTAINERS file for Broadcom SoCs:
- add Ray and Scott for mach-bcm
- remove Christian for mach-bcm
- remove Marc for brcmstb
* tag 'arm-soc/for-4.1/maintainers' of http://github.com/broadcom/stblinux:
MAINTAINERS: Update brcmstb entry
MAINTAINERS: Remove Christian Daudt for mach-bcm
MAINTAINERS: Update mach-bcm maintainers list
Arnd Bergmann [Thu, 7 May 2015 16:23:49 +0000 (18:23 +0200)]
Merge tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fix for 4.1" from Gregory CLEMENT:
Disable the unused internal RTC in the dts of the OpenBlock AX3
* tag 'mvebu-fixes-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: armada-xp-openblocks-ax3-4: Disable internal RTC
Arnd Bergmann [Thu, 7 May 2015 16:23:00 +0000 (18:23 +0200)]
Merge tag 'fixes-for-v4.1-rc2' of https://github.com/rjarzmik/linux into fixes
Merged "ARM: pxa: fixes for v4.1-rc2" from Robert Jarzmik:
These fixes reenable the lubbock(pxa25x) and mainstone(pxa27x)
platforms, which were broken since the gpio handling was
converted to a driver, and the interrupt ordering broke the
external interrupts of these systems.
* tag 'fixes-for-v4.1-rc2' of https://github.com/rjarzmik/linux:
ARM: pxa: lubbock: use new pxa_cplds driver
ARM: pxa: mainstone: use new pxa_cplds driver
ARM: pxa: pxa_cplds: add lubbock and mainstone IO
Arnd Bergmann [Thu, 7 May 2015 16:21:57 +0000 (18:21 +0200)]
Merge tag 'imx-fixes-4.1' of git://git./linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.1" from Shawn Guo:
- A couple of imx23-olinuxino device tree fixes regarding to LED GPIO
polarity and USB dr_mode setting
- One i.MX28 device tree fix on AUART4 TX-DMA interrupt name
- Add missing pwm-cells to PWM4 for i.MX25 device tree
- Fix imx6q-phytec device tree to get correct USB VBUS control
- Drop invalid pinctrl-assert-gpios property from imx6qdl-sabreauto
device tree, which was sneaked in from vendor device tree
- One fix on Wolfram's broken email address
* tag 'imx-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-sabreauto: remove pinctrl-assert-gpios
ARM: dts: imx28: Fix AUART4 TX-DMA interrupt name
ARM: dts: imx25: Add #pwm-cells to pwm4
ARM: dts: imx6: phyFLEX: USB VBUS control is active-high
ARM: mach-imx: devices: platform-sdhci-esdhc-imx: fix broken email address
ARM: dts: imx23-olinuxino: Fix dr_mode of usb0
ARM: dts: imx23-olinuxino: Fix polarity of LED GPIO
Arnd Bergmann [Thu, 7 May 2015 16:19:27 +0000 (18:19 +0200)]
Merge tag 'v4.1-rockchip-socfixes1' of git://git./linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: some soc-level fixes for 4.1" from Heiko Stübner:
Two fixes from Chris Zhong, fixing some suspend oddities.
And I've given up on the timer7 issue. While I initially thought
devices would either have both the grave mmu issue requiring a uboot
update and the timer7 issue or none, it looks like in all units in the
field the mmu issue got fixed while the timer7 issue stayed on.
So instead of making everybody wanting to use mainline jump through a
hoop just make sure timer7 is on on boot before we init the arch-timer.
* tag 'v4.1-rockchip-socfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
rockchip: make sure timer7 is enabled on rk3288 platforms
ARM: rockchip: fix undefined instruction of reset_ctrl_regs
ARM: rockchip: disable dapswjdp during suspend
Linus Torvalds [Thu, 7 May 2015 15:27:38 +0000 (08:27 -0700)]
Merge tag 'pinctrl-v4.1-3' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a smallish set of pin control fixes for the v4.1 cycle,
collected the last two weeks:
- fix a real nasty legacy bug that has screwed up the protection of
adding pinctrl maps dynamically. Normally this didn't happen so
much but Dough Anderson ran into it and fixed it, kudos!
- minor driver fixes for Qualcomm spmi, mediatek and Marvell drivers"
* tag 'pinctrl-v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: Don't just pretend to protect pinctrl_maps, do it for real
pinctrl: mediatek: mtk-common: initialize unmask
pinctrl: qcom-spmi-mpp: Fix input value report
pinctrl: qcom-spmi: Fix pin direction configuration
pinctrl: mvebu: Fix mapping of pin 63 (gpo -> gpio)
Linus Torvalds [Thu, 7 May 2015 15:18:01 +0000 (08:18 -0700)]
Merge tag 'vfio-v4.1-rc3' of git://github.com/awilliam/linux-vfio
Pull vfio fixes from Alex Williamson:
"Fix some undesirable behavior with the vfio device request interface:
- increase verbosity of device request channel (Alex Williamson)
- fix runaway interruptible timeout (Alex Williamson)"
* tag 'vfio-v4.1-rc3' of git://github.com/awilliam/linux-vfio:
vfio: Fix runaway interruptible timeout
vfio-pci: Log device requests more verbosely
Christian König [Thu, 7 May 2015 13:19:25 +0000 (15:19 +0200)]
drm/radeon: stop trying to suspend UVD sessions
Saving the current UVD state on suspend and restoring it on resume
just doesn't work reliable. Just close cleanup all sessions on suspend.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 7 May 2015 13:19:24 +0000 (15:19 +0200)]
drm/radeon: more strictly validate the UVD codec
MPEG 2/4 are only supported since UVD3.
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 7 May 2015 13:19:23 +0000 (15:19 +0200)]
drm/radeon: make UVD handle checking more strict
Invalid messages can crash the hw otherwise.
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 7 May 2015 13:19:22 +0000 (15:19 +0200)]
drm/radeon: make VCE handle check more strict
Invalid handles can crash the hw.
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Tue, 5 May 2015 07:52:12 +0000 (09:52 +0200)]
drm/radeon: fix userptr lockup
We shouldn't try to reserve and wait for a BO that isn't bound. Otherwise
we can run into a deadlock if we have a fault during binding the BO.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
monk.liu [Tue, 5 May 2015 07:24:17 +0000 (09:24 +0200)]
drm/radeon: fix userptr BO unpin bug v3
Fixing a memory leak with userptrs.
v2: clean up the loop, use an iterator instead
v3: remove unused variable
Signed-off-by: monk.liu <monk.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xihan Zhang [Tue, 28 Apr 2015 15:48:40 +0000 (23:48 +0800)]
drm/amdkfd: Initialize sdma vm when creating sdma queue
This patch fixes a bug where sdma vm wasn't initialized when
an sdma queue was created in HWS mode.
This caused GPUVM faults to appear on dmesg and it is one of the
causes that SDMA queues are not working.
Signed-off-by: Xihan Zhang <xihan.zhang@amd.com>
Reviewed-by: Ben Goz <ben.goz@amd.comt>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Oded Gabbay [Tue, 5 May 2015 08:15:07 +0000 (11:15 +0300)]
drm/amdkfd: Don't report local memory size
This patch sets the local memory size that is reported to userspace to 0.
This is done to make sure that userspace won't try to allocate local memory
for HSA.
As long as amdkfd doesn't support allocating local memory for HSA,
we need this patch.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Oded Gabbay [Tue, 14 Apr 2015 11:13:18 +0000 (14:13 +0300)]
drm/amdkfd: allow unregister process with queues
Sometimes we might unregister process that have queues, because we couldn't
preempt the queues. Until now we blocked it with BUG_ON but instead just
print it as debug.
Reviewed-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Thu, 7 May 2015 14:04:33 +0000 (07:04 -0700)]
Merge tag 'for-linus' of git://github.com/dledford/linux
Pull infiniband updates from Doug Ledford:
"Minor updates for 4.1-rc
Most of the changes are fairly small and well confined. The iWARP
address reporting changes are the only ones that are a medium size. I
had these queued up prior to rc1, but due to the shuffle in
maintainers, they did not get submitted when I expected. My apologies
for that. I feel comfortable with them however due to the testing
they've received, so I left them in this submission"
* tag 'for-linus' of git://github.com/dledford/linux:
MAINTAINERS: Update InfiniBand subsystem maintainer
MAINTAINERS: add include/rdma/ to InfiniBand subsystem
IPoIB/CM: Fix indentation level
iw_cxgb4: Remove negative advice dmesg warnings
IB/core: Fix unaligned accesses
IB/core: change rdma_gid2ip into void function as it always return zero
IB/qib: use arch_phys_wc_add()
IB/qib: add acounting for MTRR
IB/core: dma unmap optimizations
IB/core: dma map/unmap locking optimizations
RDMA/cxgb4: Report the actual address of the remote connecting peer
RDMA/nes: Report the actual address of the remote connecting peer
RDMA/core: Enable the iWarp Port Mapper to provide the actual address of the connecting peer to its clients
iw_cxgb4: enforce qp/cq id requirements
iw_cxgb4: use BAR2 GTS register for T5 kernel mode CQs
iw_cxgb4: 32b platform fixes
iw_cxgb4: Cleanup register defines/MACROS
RDMA/CMA: Canonize IPv4 on IPV6 sockets properly
Chris Wilson [Thu, 7 May 2015 10:16:26 +0000 (11:16 +0100)]
drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
Since the introduction of BIOS fb preservation, circa 3.17, we began
encountering a failure during boot when trying to use force-detect
before GEM was initialised. That bug is from
commit
7fad798e16fecddd41c6a91728a09f0b9507e40c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jul 4 17:51:47 2012 +0200
drm/i915: ensure the force pipe A quirk is actually followed
but investigation of the affected machine revealed that it was using a
PIPE-A quirk even though it was a 945GSE and the quirk is only supposed
to be used to workaround a hardware issue on 830/845. That quirk was
added for this HP Mini in
commit
6b93afc564a5e74b0eaaa46c95f557449951b3b9
Author: Bryce Harrington <bryce@bryceharrington.org>
Date: Wed May 27 03:40:52 2009 -0700
add pipe a force quirk for Dell mini
in order to workaround an issue with the BIOS behaving strangely during
lid-close. Since then we have a much larger hammer to thwart the BIOS
after opening the lid and the PIPE-A quirk is no longer required.
Reported-and-tested-by: Apostolos B. <barz621@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=21960
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87521
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Sonika Jindal [Thu, 7 May 2015 08:29:28 +0000 (13:59 +0530)]
drm/i915: Sink rate read should be saved in deca-kHz
The sink rate read from supported link rate table is in KHz as per spec
while in drm, the saved clock is in deca-KHz. So divide the link rate by
10 before storing.
Reading of rates was added by:
commit
fc0f8e25318f ("drm/i915/skl: Read sink supported rates from edp
panel")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Alex Bennée [Wed, 29 Apr 2015 15:18:46 +0000 (16:18 +0100)]
tracing: Make ftrace_print_array_seq compute buf_len
The only caller to this function (__print_array) was getting it wrong by
passing the array length instead of buffer length. As the element size
was already being passed for other reasons it seems reasonable to push
the calculation of buffer length into the function.
Link: http://lkml.kernel.org/r/1430320727-14582-1-git-send-email-alex.bennee@linaro.org
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Filipe Manana [Wed, 6 May 2015 10:17:01 +0000 (11:17 +0100)]
Btrfs: fix wrong mapping flags for free space inode
We were passing a flags value that differed from the intention in commit
2b108268006e ("Btrfs: don't use highmem for free space cache pages").
This caused problems in a ARM machine, leaving btrfs unusable there.
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Linus Torvalds [Wed, 6 May 2015 22:58:06 +0000 (15:58 -0700)]
Merge tag 'for-linus-4.1b-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix blkback regression if using persistent grants
- fix various event channel related suspend/resume bugs
- fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
* tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
hypervisor/x86/xen: Unset X86_BUG_SYSRET_SS_ATTRS on Xen PV guests
xen/events: Set irq_info->evtchn before binding the channel to CPU in __startup_pirq()
xen/console: Update console event channel on resume
xen/xenbus: Update xenbus event channel on resume
xen/events: Clear cpu_evtchn_mask before resuming
xen-pciback: Add name prefix to global 'permissive' variable
xen: Suspend ticks on all CPUs during suspend
xen/grant: introduce func gnttab_unmap_refs_sync()
xen/blkback: safely unmap purge persistent grants
Linus Torvalds [Wed, 6 May 2015 17:57:37 +0000 (10:57 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"EFI fixes, and FPU fix, a ticket spinlock boundary condition fix and
two build fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Always restore_xinit_state() when use_eager_cpu()
x86: Make cpu_tss available to external modules
efi: Fix error handling in add_sysfs_runtime_map_entry()
x86/spinlocks: Fix regression in spinlock contention detection
x86/mm: Clean up types in xlate_dev_mem_ptr()
x86/efi: Store upper bits of command line buffer address in ext_cmd_line_ptr
efivarfs: Ensure VariableName is NUL-terminated
Linus Torvalds [Wed, 6 May 2015 17:47:25 +0000 (10:47 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also an uncore PMU driver fix and an uncore
PMU driver hardware-enablement addition"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Fix segfault if passed with ''.
perf report: Fix -T/--threads option to work again
perf bench numa: Fix immediate meeting of convergence condition
perf bench numa: Fixes of --quiet argument
perf bench futex: Fix hung wakeup tasks after requeueing
perf probe: Fix bug with global variables handling
perf top: Fix a segfault when kernel map is restricted.
tools lib traceevent: Fix build failure on 32-bit arch
perf kmem: Fix compiles on RHEL6/OL6
tools lib api: Undefine _FORTIFY_SOURCE before setting it
perf kmem: Consistently use PRIu64 for printing u64 values
perf trace: Disable events and drain events when forked workload ends
perf trace: Enable events when doing system wide tracing and starting a workload
perf/x86/intel/uncore: Move PCI IDs for IMC to uncore driver
perf/x86/intel/uncore: Add support for Intel Haswell ULT (lower power Mobile Processor) IMC uncore PMUs
perf/x86/intel: Add cpu_(prepare|starting|dying) for core_pmu
Linus Torvalds [Wed, 6 May 2015 17:26:37 +0000 (10:26 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull RCU fix from Ingo Molnar:
"An RCU Kconfig fix that eliminates an annoying interactive kconfig
question for CONFIG_RCU_TORTURE_TEST_SLOW_INIT"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Control grace-period delays directly from value
Christophe Leroy [Wed, 6 May 2015 15:26:47 +0000 (17:26 +0200)]
splice: sendfile() at once fails for big files
Using sendfile with below small program to get MD5 sums of some files,
it appear that big files (over 64kbytes with 4k pages system) get a
wrong MD5 sum while small files get the correct sum.
This program uses sendfile() to send a file to an AF_ALG socket
for hashing.
/* md5sum2.c */
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <string.h>
#include <fcntl.h>
#include <sys/socket.h>
#include <sys/stat.h>
#include <sys/types.h>
#include <linux/if_alg.h>
int main(int argc, char **argv)
{
int sk = socket(AF_ALG, SOCK_SEQPACKET, 0);
struct stat st;
struct sockaddr_alg sa = {
.salg_family = AF_ALG,
.salg_type = "hash",
.salg_name = "md5",
};
int n;
bind(sk, (struct sockaddr*)&sa, sizeof(sa));
for (n = 1; n < argc; n++) {
int size;
int offset = 0;
char buf[4096];
int fd;
int sko;
int i;
fd = open(argv[n], O_RDONLY);
sko = accept(sk, NULL, 0);
fstat(fd, &st);
size = st.st_size;
sendfile(sko, fd, &offset, size);
size = read(sko, buf, sizeof(buf));
for (i = 0; i < size; i++)
printf("%2.2x", buf[i]);
printf(" %s\n", argv[n]);
close(fd);
close(sko);
}
exit(0);
}
Test below is done using official linux patch files. First result is
with a software based md5sum. Second result is with the program above.
root@vgoip:~# ls -l patch-3.6.*
-rw-r--r-- 1 root root 64011 Aug 24 12:01 patch-3.6.2.gz
-rw-r--r-- 1 root root 94131 Aug 24 12:01 patch-3.6.3.gz
root@vgoip:~# md5sum patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz
root@vgoip:~# ./md5sum2 patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
5fd77b24e68bb24dcc72d6e57c64790e patch-3.6.3.gz
After investivation, it appears that sendfile() sends the files by blocks
of 64kbytes (16 times PAGE_SIZE). The problem is that at the end of each
block, the SPLICE_F_MORE flag is missing, therefore the hashing operation
is reset as if it was the end of the file.
This patch adds SPLICE_F_MORE to the flags when more data is pending.
With the patch applied, we get the correct sums:
root@vgoip:~# md5sum patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz
root@vgoip:~# ./md5sum2 patch-3.6.*
b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz
c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Jens Axboe <axboe@fb.com>
Doug Anderson [Fri, 1 May 2015 16:01:27 +0000 (09:01 -0700)]
pinctrl: Don't just pretend to protect pinctrl_maps, do it for real
Way back, when the world was a simpler place and there was no war, no
evil, and no kernel bugs, there was just a single pinctrl lock. That
was how the world was when (
57291ce pinctrl: core device tree mapping
table parsing support) was written. In that case, there were
instances where the pinctrl mutex was already held when
pinctrl_register_map() was called, hence a "locked" parameter was
passed to the function to indicate that the mutex was already locked
(so we shouldn't lock it again).
A few years ago in (
42fed7b pinctrl: move subsystem mutex to
pinctrl_dev struct), we switched to a separate pinctrl_maps_mutex.
...but (oops) we forgot to re-think about the whole "locked" parameter
for pinctrl_register_map(). Basically the "locked" parameter appears
to still refer to whether the bigger pinctrl_dev mutex is locked, but
we're using it to skip locks of our (now separate) pinctrl_maps_mutex.
That's kind of a bad thing(TM). Probably nobody noticed because most
of the calls to pinctrl_register_map happen at boot time and we've got
synchronous device probing. ...and even cases where we're
asynchronous don't end up actually hitting the race too often. ...but
after banging my head against the wall for a bug that reproduced 1 out
of 1000 reboots and lots of looking through kgdb, I finally noticed
this.
Anyway, we can now safely remove the "locked" parameter and go back to
a war-free, evil-free, and kernel-bug-free world.
Fixes: 42fed7ba44e4 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stefano Stabellini [Fri, 24 Apr 2015 09:16:40 +0000 (10:16 +0100)]
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
Make sure that xen_swiotlb_init allocates buffers that are DMA capable
when at least one memblock is available below 4G. Otherwise we assume
that all devices on the SoC can cope with >4G addresses. We do this on
ARM and ARM64, where dom0 is mapped 1:1, so pfn == mfn in this case.
No functional changes on x86.
From: Chen Baozi <baozich@gmail.com>
Signed-off-by: Chen Baozi <baozich@gmail.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Tested-by: Chen Baozi <baozich@gmail.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Tony Lindgren [Thu, 23 Apr 2015 23:54:17 +0000 (16:54 -0700)]
gpio: omap: Fix regression for MPUIO interrupts
At some point with all the GPIO clean-up we've broken the
MPUIO interrupts. Those are just a little bit different from
the GPIO interrupts, so we can fix it up just by setting
different irqchip functions for it. And then we can just
remove all old code trying to do the same.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Chuanxiao Dong [Tue, 12 Aug 2014 04:01:30 +0000 (12:01 +0800)]
mmc: card: Don't access RPMB partitions for normal read/write
During kernel boot, it will try to read some logical sectors
of each block device node for the possible partition table.
But since RPMB partition is special and can not be accessed
by normal eMMC read / write CMDs, it will cause below error
messages during kernel boot:
...
mmc0: Got data interrupt 0x00000002 even though no data operation was in progress.
mmcblk0rpmb: error -110 transferring data, sector 0, nr 32, cmd response 0x900, card status 0xb00
mmcblk0rpmb: retrying using single block read
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
end_request: I/O error, dev mmcblk0rpmb, sector 0
Buffer I/O error on device mmcblk0rpmb, logical block 0
end_request: I/O error, dev mmcblk0rpmb, sector 8
Buffer I/O error on device mmcblk0rpmb, logical block 1
end_request: I/O error, dev mmcblk0rpmb, sector 16
Buffer I/O error on device mmcblk0rpmb, logical block 2
end_request: I/O error, dev mmcblk0rpmb, sector 24
Buffer I/O error on device mmcblk0rpmb, logical block 3
...
This patch will discard the access request in eMMC queue if
it is RPMB partition access request. By this way, it avoids
trigger above error messages.
Fixes: 090d25fe224c ("mmc: core: Expose access to RPMB partition")
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Michael Shigorin <mike@altlinux.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Takeshi Kihara [Wed, 29 Apr 2015 17:03:51 +0000 (02:03 +0900)]
mmc: sh_mmcif: Fix timeout value for command request
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
changed the timeout value from 1000 jiffies to 1s. In the case where
HZ is 1000 the values are the same. However, for smaller HZ values the
timeout is now smaller, 1s instead of 10s in the case of HZ=100.
Since the timeout occurs in spite of a normal data transfer a timeout of
10s seems more appropriate. This restores the previous timeout in the
case where HZ=100 and results in an increase over the previous timeout
for larger values of HZ.
Fixes: f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[horms: rewrote changelog to refer to HZ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bobby Powers [Mon, 27 Apr 2015 15:10:41 +0000 (08:10 -0700)]
x86/fpu: Always restore_xinit_state() when use_eager_cpu()
The following commit:
f893959b0898 ("x86/fpu: Don't abuse drop_init_fpu() in flush_thread()")
removed drop_init_fpu() usage from flush_thread(). This seems to break
things for me - the Go 1.4 test suite fails all over the place with
floating point comparision errors (offending commit found through
bisection).
The functional change was that flush_thread() after this commit
only calls restore_init_xstate() when both use_eager_fpu() and
!used_math() are true. drop_init_fpu() (now fpu_reset_state()) calls
restore_init_xstate() regardless of whether current used_math() - apply
the same logic here.
Switch used_math() -> tsk_used_math(tsk) to consistently use the grabbed
tsk instead of current, like in the rest of flush_thread().
Tested-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pekka Riikonen <priikone@iki.fi>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: f893959b ("x86/fpu: Don't abuse drop_init_fpu() in flush_thread()")
Link: http://lkml.kernel.org/r/1430147441-9820-1-git-send-email-bobbypowers@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jani Nikula [Tue, 5 May 2015 13:32:12 +0000 (16:32 +0300)]
drm/i915/dp: there is no audio on port A
The eDP port A register on PCH split platforms has a slightly different
register layout from the other ports, with bit 6 being either alternate
scrambler reset or reserved, depending on the generation. Our
misinterpretation of the bit as audio has lead to warning.
Fix this by not enabling audio on port A, since none of our platforms
support audio on port A anyway.
v2: DDI doesn't have audio on port A either (Sivakumar Thulasimani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89958
Reported-and-tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ingo Molnar [Wed, 6 May 2015 06:29:37 +0000 (08:29 +0200)]
Merge tag 'efi-urgent' of git://git./linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Avoid garbage names in efivarfs due to buggy firmware by zeroing
EFI variable name. (Ross Lagerwall)
* Stop erroneously dropping upper 32 bits of boot command line pointer
in EFI boot stub and stash them in ext_cmd_line_ptr. (Roy Franz)
* Fix double-free bug in error handling code path of EFI runtime map
code. (Dan Carpenter)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Wed, 6 May 2015 02:54:11 +0000 (04:54 +0200)]
Merge tag 'perf-urgent-for-mingo' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix 'perf probe -a' segfault if passed with '' (Wang Nan)
- Fix report -T/--threads option (Namhyung Kim)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Wed, 6 May 2015 02:42:01 +0000 (19:42 -0700)]
Merge tag 'for-linus-4.1-1' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Lots of minor IPMI fixes, especially ones that have have come up since
the SSIF driver has been in the main kernel for a while"
* tag 'for-linus-4.1-1' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: Fix multi-part message handling
ipmi: Add alert handling to SSIF
ipmi: Fix a problem that messages are not issued in run_to_completion mode
ipmi: Report an error if ACPI _IFT doesn't exist
ipmi: Remove unused including <linux/version.h>
ipmi: Don't report err in the SI driver for SSIF devices
ipmi: Remove incorrect use of seq_has_overflowed
ipmi:ssif: Ignore spaces when comparing I2C adapter names
ipmi_ssif: Fix the logic on user-supplied addresses
Linus Torvalds [Wed, 6 May 2015 01:52:13 +0000 (18:52 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 patches
This includes a new rtc driver for the Abracon AB x80x and isn't very
appropriate for -rc2. It was still being fiddled with a bit during
the merge window and I fell asleep during -rc1"
[ So I took the new driver, it seems small and won't regress anything.
I'm a softy. - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
rtc: armada38x: fix concurrency access in armada38x_rtc_set_time
ocfs2: dlm: fix race between purge and get lock resource
nilfs2: fix sanity check of btree level in nilfs_btree_root_broken()
util_macros.h: have array pointer point to array of constants
configfs: init configfs module earlier at boot time
mm/hwpoison-inject: check PageLRU of hpage
mm/hwpoison-inject: fix refcounting in no-injection case
mm: soft-offline: fix num_poisoned_pages counting on concurrent events
rtc: add rtc-abx80x, a driver for the Abracon AB x80x i2c rtc
Documentation: bindings: add abracon,abx80x
kasan: show gcc version requirements in Kconfig and Documentation
mm/memory-failure: call shake_page() when error hits thp tail page
lib: delete lib/find_last_bit.c
MAINTAINERS: add co-maintainer for LED subsystem
zram: add Designated Reviewer for zram in MAINTAINERS
revert "zram: move compact_store() to sysfs functions area"
Linus Torvalds [Wed, 6 May 2015 01:14:04 +0000 (18:14 -0700)]
Merge tag 'platform-drivers-x86-v4.1-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"This includes a trivial warning and adding a Lenovo laptop to an
existing quirk.
I've held off on things like the latter in the past, but I didn't feel
it was risky enough to push out to 4.2.
- thinkpad_acpi:
Fix warning for static not at beginning
- ideapad_laptop:
Add Lenovo G40-30 to devices without radio switch"
* tag 'platform-drivers-x86-v4.1-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
thinkpad_acpi: Fix warning for static not at beginning
ideapad_laptop: Add Lenovo G40-30 to devices without radio switch
Corey Minyard [Wed, 29 Apr 2015 22:59:21 +0000 (17:59 -0500)]
ipmi: Fix multi-part message handling
Lots of little fixes for multi-part messages:
The values was not being re-initialized, if something went wrong
handling a multi-part message and it got left in a bad state, it
might be an issue.
The commands were not correct when issuing multi-part reads, the
code was not passing in the proper value for commands. Also clean
up some minor formatting issues.
Get the block number from the right location, limit the maximum send
message size to 63 bytes and explain why, and fix some minor sylistic
issues.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Corey Minyard [Fri, 24 Apr 2015 12:46:06 +0000 (07:46 -0500)]
ipmi: Add alert handling to SSIF
The SSIF interface can optionally have an SMBus alert come in when
data is ready. Unfortunately, the IPMI spec gives wiggle room to
the implementer to allow them to always have the alert enabled,
even if the driver doesn't enable it. So implement alerts.
If you don't in this situation, the SMBus alert handling will
constantly complain.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Hidehiro Kawai [Thu, 23 Apr 2015 02:16:44 +0000 (11:16 +0900)]
ipmi: Fix a problem that messages are not issued in run_to_completion mode
start_next_msg() issues a message placed in smi_info->waiting_msg
if it is non-NULL. However, sender() sets a message to
smi_info->curr_msg and NULL to smi_info->waiting_msg in the context
of run_to_completion mode. As the result, it leads an infinite
loop by waiting the completion of unissued message when leaving
dying message after kernel panic.
sender() should set the message to smi_info->waiting_msg not
curr_msg.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Corey Minyard [Wed, 22 Apr 2015 18:25:40 +0000 (13:25 -0500)]
ipmi: Report an error if ACPI _IFT doesn't exist
When probing an ACPI table, report a specific error, instead of just
returning an error, if _IFT doesn't exist.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Wei Yongjun [Thu, 16 Apr 2015 13:09:53 +0000 (21:09 +0800)]
ipmi: Remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Gregory CLEMENT [Tue, 5 May 2015 23:24:05 +0000 (16:24 -0700)]
rtc: armada38x: fix concurrency access in armada38x_rtc_set_time
While setting the time, the RTC TIME register should not be accessed.
However due to hardware constraints, setting the RTC time involves
sleeping during 100ms. This sleep was done outside the critical section
protected by the spinlock, so it was possible to read the RTC TIME
register and get an incorrect value. This patch introduces a mutex for
protecting the RTC TIME access, unlike the spinlock it is allowed to
sleep in a critical section protected by a mutex.
The RTC STATUS register can still be used from the interrupt handler but
it has no effect on setting the time.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org> [4.0]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi [Tue, 5 May 2015 23:24:02 +0000 (16:24 -0700)]
ocfs2: dlm: fix race between purge and get lock resource
There is a race window in dlm_get_lock_resource(), which may return a
lock resource which has been purged. This will cause the process to
hang forever in dlmlock() as the ast msg can't be handled due to its
lock resource not existing.
dlm_get_lock_resource {
...
spin_lock(&dlm->spinlock);
tmpres = __dlm_lookup_lockres_full(dlm, lockid, namelen, hash);
if (tmpres) {
spin_unlock(&dlm->spinlock);
>>>>>>>> race window, dlm_run_purge_list() may run and purge
the lock resource
spin_lock(&tmpres->spinlock);
...
spin_unlock(&tmpres->spinlock);
}
}
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryusuke Konishi [Tue, 5 May 2015 23:24:00 +0000 (16:24 -0700)]
nilfs2: fix sanity check of btree level in nilfs_btree_root_broken()
The range check for b-tree level parameter in nilfs_btree_root_broken()
is wrong; it accepts the case of "level == NILFS_BTREE_LEVEL_MAX" even
though the level is limited to values in the range of 0 to
(NILFS_BTREE_LEVEL_MAX - 1).
Since the level parameter is read from storage device and used to index
nilfs_btree_path array whose element count is NILFS_BTREE_LEVEL_MAX, it
can cause memory overrun during btree operations if the boundary value
is set to the level parameter on device.
This fixes the broken sanity check and adds a comment to clarify that
the upper bound NILFS_BTREE_LEVEL_MAX is exclusive.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guenter Roeck [Tue, 5 May 2015 23:23:57 +0000 (16:23 -0700)]
util_macros.h: have array pointer point to array of constants
Using the new find_closest() macro can result in the following sparse
warnings.
drivers/hwmon/lm85.c:194:16: warning:
incorrect type in initializer (different modifiers)
drivers/hwmon/lm85.c:194:16: expected int *__fc_a
drivers/hwmon/lm85.c:194:16: got int static const [toplevel] *<noident>
drivers/hwmon/lm85.c:210:16: warning:
incorrect type in initializer (different modifiers)
drivers/hwmon/lm85.c:210:16: expected int *__fc_a
drivers/hwmon/lm85.c:210:16: got int const *map
This is because the array passed to find_closest() will typically be
declared as array of constants, but the macro declares a non-constant
pointer to it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Baluta [Tue, 5 May 2015 23:23:54 +0000 (16:23 -0700)]
configfs: init configfs module earlier at boot time
We need this earlier in the boot process to allow various subsystems to
use configfs (e.g Industrial IIO).
Also, debugfs is at core_initcall level and configfs should be on the same
level from infrastructure point of view.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Tue, 5 May 2015 23:23:52 +0000 (16:23 -0700)]
mm/hwpoison-inject: check PageLRU of hpage
Hwpoison injector checks PageLRU of the raw target page to find out
whether the page is an appropriate target, but current code now filters
out thp tail pages, which prevents us from testing for such cases via this
interface. So let's check hpage instead of p.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Dean Nelson <dnelson@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.055275 seconds and 5 git commands to generate.