Gavin Shan [Mon, 17 Sep 2012 04:34:27 +0000 (04:34 +0000)]
powerpc/eeh: Lock module while handling EEH event
The EEH core is talking with the PCI device driver to determine the
action (purely reset, or PCI device removal). During the period, the
driver might be unloaded and in turn causes kernel crash as follows:
EEH: Detected PCI bus error on PHB#4-PE#10000
EEH: This PCI device has failed 3 times in the last hour
lpfc 0004:01:00.0: 0:2710 PCI channel disable preparing for reset
Unable to handle kernel paging request for data at address 0x00000490
Faulting instruction address: 0xd00000000e682c90
cpu 0x1: Vector: 300 (Data Access) at [
c000000fc75ffa20]
pc:
d00000000e682c90: .lpfc_io_error_detected+0x30/0x240 [lpfc]
lr:
d00000000e682c8c: .lpfc_io_error_detected+0x2c/0x240 [lpfc]
sp:
c000000fc75ffca0
msr:
8000000000009032
dar: 490
dsisr:
40000000
current = 0xc000000fc79b88b0
paca = 0xc00000000edb0380 softe: 0 irq_happened: 0x00
pid = 3386, comm = eehd
enter ? for help
[
c000000fc75ffca0]
c000000fc75ffd30 (unreliable)
[
c000000fc75ffd30]
c00000000004fd3c .eeh_report_error+0x7c/0xf0
[
c000000fc75ffdc0]
c00000000004ee00 .eeh_pe_dev_traverse+0xa0/0x180
[
c000000fc75ffe70]
c00000000004ffd8 .eeh_handle_event+0x68/0x300
[
c000000fc75fff00]
c0000000000503a0 .eeh_event_handler+0x130/0x1a0
[
c000000fc75fff90]
c000000000020138 .kernel_thread+0x54/0x70
1:mon>
The patch increases the reference of the corresponding driver modules
while EEH core does the negotiation with PCI device driver so that the
corresponding driver modules can't be unloaded during the period and
we're safe to refer the callbacks.
Cc: stable@vger.kernel.org
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Sun, 16 Sep 2012 23:54:31 +0000 (23:54 +0000)]
powerpc/kprobe: Don't emulate store when kprobe stwu r1
We don't do the real store operation for kprobing 'stwu Rx,(y)R1'
since this may corrupt the exception frame, now we will do this
operation safely in exception return code after migrate current
exception frame below the kprobed function stack.
So we only update gpr[1] here and trigger a thread flag to mask
this.
Note we should make sure if we trigger kernel stack over flow.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Sun, 16 Sep 2012 23:54:30 +0000 (23:54 +0000)]
powerpc/kprobe: Complete kprobe and migrate exception frame
We can't emulate stwu since that may corrupt current exception stack.
So we will have to do real store operation in the exception return code.
Firstly we'll allocate a trampoline exception frame below the kprobed
function stack and copy the current exception frame to the trampoline.
Then we can do this real store operation to implement 'stwu', and reroute
the trampoline frame to r1 to complete this exception migration.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Sun, 16 Sep 2012 23:54:29 +0000 (23:54 +0000)]
powerpc/kprobe: Introduce a new thread flag
We need to add a new thread flag, TIF_EMULATE_STACK_STORE,
for emulating stack store operation while exiting exception.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Bharat Bhushan [Tue, 11 Sep 2012 00:19:45 +0000 (00:19 +0000)]
powerpc: Remove unused __get_user64() and __put_user64()
__get_user64() and __put_user64() are not used.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Tue, 11 Sep 2012 19:16:18 +0000 (19:16 +0000)]
powerpc/eeh: Global mutex to protect PE tree
We have missed lots of situations where the PE hierarchy tree need
protection through the EEH global mutex. The patch fixes that for
those public APIs implemented in eeh_pe.c. The only exception is
eeh_pe_restore_bars() because it calls eeh_pe_dev_traverse(), which
has been protected by the mutex.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Tue, 11 Sep 2012 19:16:17 +0000 (19:16 +0000)]
powerpc/eeh: Remove EEH PE for normal PCI hotplug
Function eeh_rmv_from_parent_pe() could be called by the path of
either normal PCI hotplug, or EEH recovery. For the former case,
we need purge the corresponding PE on removal of the associated
PE bus.
The patch tries to cover that by passing more information to function
pcibios_remove_pci_devices() so that we know if the corresponding PE
needs to be purged or be marked as "invalid".
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Tue, 11 Sep 2012 19:16:16 +0000 (19:16 +0000)]
powerpc/eeh: Introduce EEH_PE_INVALID type PE
When EEH error happens on the PE whose PCI devices don't have
attached drivers. In function eeh_handle_event(), the default
value PCI_ERS_RESULT_NONE will be returned after iterating all
drivers of those PCI devices belonging to the PE. Actually, we
don't have installed drivers for the PCI devices. Under the
circumstance, we will remove the corresponding PCI bus of the PE,
including the associated EEH devices and PE instance. However,
we still need the information stored in the PE instance to do PE
reset after that. So it's unsafe to free the PE instance.
The patch introduces EEH_PE_INVALID type PE to address the issue.
When the PCI bus and the corresponding attached EEH devices are
removed, we will mark the PE as EEH_PE_INVALID. At later point,
the PE will be changed to EEH_PE_DEVICE or EEH_PE_BUS when the
corresponding EEH devices are attached again.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 13 Sep 2012 23:01:31 +0000 (23:01 +0000)]
powerpc: Add an xmon command to dump one or all pacas
This was originally motivated by a desire to see the mapping between
logical and hardware cpu numbers.
But it seemed that it made more sense to just add a command to dump
(most of) the paca.
With no arguments "dp" will dump the paca for the current cpu.
It also takes an argument, eg. "dp 3" which is the logical cpu number
in hex. This form does not check if the cpu is possible, but displays
the paca regardless, as well as the cpu's state in the possible, present
and online masks.
Thirdly, "dpa" will display the paca for all possible cpus. If there are
no possible cpus, like early in boot, it will tell you that.
Sample output, number in brackets is the offset into the struct:
2:mon> dp 3
paca for cpu 0x3 @
c00000000ff20a80:
possible = yes
present = yes
online = yes
lock_token = 0x8000 (0x8)
paca_index = 0x3 (0xa)
kernel_toc = 0xc00000000144f990 (0x10)
kernelbase = 0xc000000000000000 (0x18)
kernel_msr = 0xb000000000001032 (0x20)
stab_real = 0x0 (0x28)
stab_addr = 0x0 (0x30)
emergency_sp = 0xc00000003ffe4000 (0x38)
data_offset = 0xa40000 (0x40)
hw_cpu_id = 0x9 (0x50)
cpu_start = 0x1 (0x52)
kexec_state = 0x0 (0x53)
__current = 0xc00000007e568680 (0x218)
kstack = 0xc00000007e5a3e30 (0x220)
stab_rr = 0x1a (0x228)
saved_r1 = 0xc00000007e7cb450 (0x230)
trap_save = 0x0 (0x240)
soft_enabled = 0x0 (0x242)
irq_happened = 0x0 (0x243)
io_sync = 0x0 (0x244)
irq_work_pending = 0x0 (0x245)
nap_state_lost = 0x0 (0x246)
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:21 +0000 (03:49 +0000)]
powerpc/powernv: Remove unused functions
We don't need them anymore. The patch removes those functions.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:20 +0000 (03:49 +0000)]
powerpc/powernv: Using PCI core to do resource assignment
Currently, the PCI probe flags "PCI_PROBE_ONLY | PCI_REASSIGN_ALL_RSRC"
used on powernv platform. That means the platform has to do the PCI
resource assignment by itself.
The patch changes the PCI probe flag to "PCI_REASSIGN_ALL_RSRC" so
that the PCI core will do the resource assignment. Also, the I/O
and MMIO minimal alignment for P2P bridges have been configured
while doing fixup for the PHBs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:19 +0000 (03:49 +0000)]
powerpc/powernv: Fix overrunning segment tracing array
There're 2 arrays introduced to trace which PE has occupied the
corresponding resource (I/O or MMIO) segment. However, we didn't
allocate enough memory for them and that possiblly leads to PE
descriptor corruption.
The patch fixes that by allocating enough memory for those 2 arrays.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:18 +0000 (03:49 +0000)]
powerpc/powernv: Skip check on PE if necessary
While the device driver or PCI core tries to enable PCI device, the
platform dependent callback "ppc_md.pcibios_enable_device_hook" will
be called to check if there has one associated PE for the PCI device.
If we don't have the associated PE for the PCI device, it's not allowed
to enable the PCI device. Unfortunately, there might have some cases
we have to enable the PCI device (e.g. P2P bridge), but the PEs have
not been created yet.
The patch handles the unfortunate cases. Each PHB (struct pnv_phb)
has one field "initialized" to trace if the PEs have been created
and configured or not. When the PEs are not available, we won't check
the associated PE for the PCI device to be enabled.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:17 +0000 (03:49 +0000)]
powerpc/powernv: Initialize DMA for PEs
The patch introduces additional wrapper function to call the original
implementation so that the DMA can be configured for all existing PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:16 +0000 (03:49 +0000)]
powerpc/powernv: I/O and MMIO resource assignment for PEs
There're 2 types of PCI bus sensitive PEs: (A) The PE includes
single PCI bus. (B) The PE includes the PCI bus and all the subordinate
PCI buses, and the patch tries to assign I/O and MMIO resources
based on created PEs. Fortunately, we figured out unified scheme
to do resource assignment for all types of PCI bus based PEs according
to Ben's idea:
- Resource assignment based on PE from top to bottom.
- The soureces, either I/O or MMIO, of the PE are figured out
from the assigned PCI bus.
- The occupied resource by parent PE could possibilly be overrided
by children PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:15 +0000 (03:49 +0000)]
powerpc/powernv: PE list based on creation order
The resource (I/O and MMIO) will be assigned on basis of PE from
top to bottom so that we can implement the trick here: the resource
that has been assigned to parent PE could be taken by child PE if
necessary.
The current implementation already has PE list per PHB basis, but
the list doesn't meet our requirment: tracing PE based on their
cration time from top to bottom. So the patch does rename for the
DMA based PE list and introduces the list to trace the PEs sequentially
based on their creation time.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Mon, 20 Aug 2012 03:49:14 +0000 (03:49 +0000)]
powerpc/powernv: Create bus sensitive PEs
Basically, there're 2 types of PCI bus sensitive PEs: (A) The PE
includes single PCI bus. (B) The PE includes the PCI bus and all
the subordinate PCI buses. At present, we'd like to put PCI bus
originated by PCI-e link to form PE that contains single PCI bus,
and the PCIe-to-PCI bridge will form the 2nd type of PE. We don't
figure out to detect PLX bridge yet. Once we can detect PLX bridge
some day, we have to put PCI buses originated from the downstream
port of PLX bridge to the 2nd type of PE.
The patch changes the original implementation for a little bit
to support 2 types of PCI bus sensitive PEs described as above.
Also, the function used to retrieve the corresponding PE according
to the given PCI device has been changed based on that because each
PCI device should trace the directly associated PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Richard Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Mon, 10 Sep 2012 15:37:43 +0000 (15:37 +0000)]
powerpc/trace: Fix interrupt tracepoints vs. RCU
There are a few tracepoints in the interrupt code path, which is before
irq_enter(), or after irq_exit(), like
trace_irq_entry()/trace_irq_exit() in do_IRQ(),
trace_timer_interrupt_entry()/trace_timer_interrupt_exit() in
timer_interrupt().
If the interrupt is from idle(), and because tracepoint contains RCU
read-side critical section, we could see following suspicious RCU usage
reported:
[ 145.127743] ===============================
[ 145.127747] [ INFO: suspicious RCU usage. ]
[ 145.127752] 3.6.0-rc3+ #1 Not tainted
[ 145.127755] -------------------------------
[ 145.127759] /root/.workdir/linux/arch/powerpc/include/asm/trace.h:33
suspicious rcu_dereference_check() usage!
[ 145.127765]
[ 145.127765] other info that might help us debug this:
[ 145.127765]
[ 145.127771]
[ 145.127771] RCU used illegally from idle CPU!
[ 145.127771] rcu_scheduler_active = 1, debug_locks = 0
[ 145.127777] RCU used illegally from extended quiescent state!
[ 145.127781] no locks held by swapper/0/0.
[ 145.127785]
[ 145.127785] stack backtrace:
[ 145.127789] Call Trace:
[ 145.127796] [
c00000000108b530] [
c000000000013c40] .show_stack
+0x70/0x1c0 (unreliable)
[ 145.127806] [
c00000000108b5e0]
[
c0000000000f59d8] .lockdep_rcu_suspicious+0x118/0x150
[ 145.127813] [
c00000000108b680] [
c00000000000fc58] .do_IRQ+0x498/0x500
[ 145.127820] [
c00000000108b750] [
c000000000003950]
hardware_interrupt_common+0x150/0x180
[ 145.127828] --- Exception: 501 at .plpar_hcall_norets+0x84/0xd4
[ 145.127828] LR = .check_and_cede_processor+0x38/0x70
[ 145.127836] [
c00000000108bab0] [
c0000000000665dc] .shared_cede_loop
+0x5c/0x100
[ 145.127844] [
c00000000108bb70] [
c000000000588ab0] .cpuidle_enter
+0x30/0x50
[ 145.127850] [
c00000000108bbe0]
[
c000000000588b0c] .cpuidle_enter_state+0x3c/0xb0
[ 145.127857] [
c00000000108bc60] [
c000000000589730] .cpuidle_idle_call
+0x150/0x6c0
[ 145.127863] [
c00000000108bd30] [
c000000000058440] .pSeries_idle
+0x10/0x40
[ 145.127870] [
c00000000108bda0] [
c00000000001683c] .cpu_idle
+0x18c/0x2d0
[ 145.127876] [
c00000000108be60] [
c00000000000b434] .rest_init
+0x124/0x1b0
[ 145.127884] [
c00000000108bef0] [
c0000000009d0d28] .start_kernel
+0x568/0x588
[ 145.127890] [
c00000000108bf90] [
c000000000009660] .start_here_common
+0x20/0x40
This is because the RCU usage in interrupt context should be used in
area marked by rcu_irq_enter()/rcu_irq_exit(), called in
irq_enter()/irq_exit() respectively.
Move them into the irq_enter()/irq_exit() area to avoid the reporting.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:57 +0000 (02:52 +0000)]
powerpc/mm: Make some of the PGTABLE_RANGE dependency explicit
slice array size and slice mask size depend on PGTABLE_RANGE.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:56 +0000 (02:52 +0000)]
powerpc/mm: Update VSID allocation documentation
This update the proto-VSID and VSID scramble related information
to be more generic by using names instead of current values.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:55 +0000 (02:52 +0000)]
powerpc/mm: Add 64TB support
Increase max addressable range to 64TB. This is not tested on
real hardware yet.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:54 +0000 (02:52 +0000)]
powerpc/mm: Use 32bit array for slb cache
With larger vsid we need to track more bits of ESID in slb cache
for slb invalidate.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:53 +0000 (02:52 +0000)]
powerpc/mm: Use the required number of VSID bits in slbmte
ASM_VSID_SCRAMBLE can leave non-zero bits in the high 28 bits of the result
for 256MB segment (40 bits for 1T segment). Properly mask them before using
the values in slbmte
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:52 +0000 (02:52 +0000)]
powerpc/mm: Increase the slice range to 64TB
This patch makes the high psizes mask as an unsigned char array
so that we can have more than 16TB. Currently we support upto
64TB
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:51 +0000 (02:52 +0000)]
powerpc/mm: Make KERN_VIRT_SIZE not dependend on PGTABLE_RANGE
As we keep increasing PGTABLE_RANGE we need not increase the virual
map area for kernel.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:50 +0000 (02:52 +0000)]
powerpc/mm: Convert virtual address to vpn
This patch convert different functions to take virtual page number
instead of virtual address. Virtual page number is virtual address
shifted right by VPN_SHIFT (12) bits. This enable us to have an
address range of upto 76 bits.
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:49 +0000 (02:52 +0000)]
powerpc/mm: Simplify hpte_decode
This patch simplify hpte_decode for easy switching of virtual address to
virtual page number in the later patch
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:48 +0000 (02:52 +0000)]
powerpc/mm: Use hpt_va to compute virtual address
Don't open code the same
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Aneesh Kumar K.V [Mon, 10 Sep 2012 02:52:47 +0000 (02:52 +0000)]
powerpc/mm: Replace open coded CONTEXT_BITS value
To clarify the meaning for future readers, replace the open coded
19 with CONTEXT_BITS
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Wed, 12 Sep 2012 13:00:09 +0000 (13:00 +0000)]
powerpc/mm: Fix typo in PTRS_PER_PUD
PTRS_PER_PUD should be based on PUD_INDEX_SIZE, not PMD_INDEX_SIZE. We
got away with it because PUD and PMD had the same index size, but this is
no longer true with Aneesh's patchset to support a 46-bit user effective
address space.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 10 Sep 2012 00:35:26 +0000 (00:35 +0000)]
powerpc: Add denormalisation exception handling for POWER6/7
On POWER6 and POWER7 if the input operand to an instruction is a
denormalised single precision binary floating point value we can take
a denormalisation exception where it's expected that the hypervisor
(HV=1) will fix up the inputs before the instruction is run.
This adds code to handle this denormalisation exception for POWER6 and
POWER7.
It also add a CONFIG_PPC_DENORMALISATION option and sets it in
pseries/ppc64_defconfig.
This is useful on bare metal systems only. Based on patch from Milton
Miller.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Mon, 17 Sep 2012 06:07:43 +0000 (16:07 +1000)]
Merge remote-tracking branch 'pci/pci/gavin-window-alignment' into next
Merge Gavin patches from the PCI tree as subsequent powerpc
patches are going to depend on them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Bjorn Helgaas [Thu, 13 Sep 2012 21:54:57 +0000 (15:54 -0600)]
Merge commit 'v3.6-rc5' into pci/gavin-window-alignment
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
Gavin Shan [Tue, 11 Sep 2012 22:59:47 +0000 (16:59 -0600)]
powerpc/powernv: I/O and memory alignment for P2P bridges
The patch implements ppc_md.pcibios_window_alignment for powernv
platform so that the resource reassignment in PCI core will be
done according to the I/O and memory alignment returned from
powernv platform. The alignments returned from powernv platform
is closely depending on the scheme for PE segmenting. Besides,
the patch isn't useful for now, but the subsequent patches will
be working based on it.
[bhelgaas: use pci_pcie_type() since pci_dev.pcie_type was removed]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gavin Shan [Tue, 11 Sep 2012 22:59:46 +0000 (16:59 -0600)]
powerpc/PCI: Override pcibios_window_alignment()
This patch implements pcibios_window_alignment() so powerpc platforms can
force P2P bridge windows to be at larger alignments than the PCI spec
requires.
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gavin Shan [Tue, 11 Sep 2012 22:59:46 +0000 (16:59 -0600)]
PCI: Refactor pbus_size_mem()
The original idea comes from Ram Pai. This patch puts the chunk of
code for calculating the minimal alignment of memory window into a
separate inline function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gavin Shan [Tue, 11 Sep 2012 22:59:46 +0000 (16:59 -0600)]
PCI: Align P2P windows using pcibios_window_alignment()
This patch changes pbus_size_io() and pbus_size_mem() to do window (I/O,
memory and prefetchable memory) reassignment based on the minimal
alignments for the P2P bridge, which was retrieved by window_alignment().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gavin Shan [Tue, 11 Sep 2012 22:59:45 +0000 (16:59 -0600)]
PCI: Add weak pcibios_window_alignment() interface
This patch implements a weak function to return the default I/O or memory
window alignment for a P2P bridge. By default, I/O windows are aligned to
4KiB or 1KiB and memory windows are aligned to 4MiB. Some platforms, e.g.,
powernv, have special alignment requirements and can override
pcibios_window_alignment().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Joe MacDonald [Tue, 21 Aug 2012 08:22:28 +0000 (08:22 +0000)]
powerpc/mm: Match variable types to API
sys_subpage_prot() takes an unsigned long for 'addr' then does some stuff
with it and the result is stored in a signed int, i, which is eventually
used as the size parameter in a copy_from_user call. Update 'i' to be an
unsigned long as well and since 'nw' is used in a size_t context which,
depending on whether this is 32- or 64-bit may be unsigned int or unsigned
long, switch that to a size_t and always be right.
Finally, since we're in the neighbourhood, make the same changes to
subpage_prot_clear().
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joe MacDonald <joe.macdonald@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Alexey Kardashevskiy [Tue, 4 Sep 2012 15:19:35 +0000 (15:19 +0000)]
powerpc/iommu: Add ppc_md.tce_get() callback for use by VFIO
The upcoming VFIO support requires a way to know which
entry in the TCE map is not empty in order to do cleanup
at QEMU exit/crash. This patch adds such functionality
to POWERNV platform code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Thu, 6 Sep 2012 21:24:58 +0000 (21:24 +0000)]
powerpc: cleanup old DABRX #defines
These are no longer used so get rid of them
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Thu, 6 Sep 2012 21:24:57 +0000 (21:24 +0000)]
powerpc: Dynamically calculate the dabrx based on kernel/user/hypervisor
Currently we mark the DABRX to interrupt on all matches
(hypervisor/kernel/user and then filter in software. We can be a lot
smarter now that we can set the DABRX dynamically.
This sets the DABRX based on the flags passed by the user.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Thu, 6 Sep 2012 21:24:56 +0000 (21:24 +0000)]
powerpc: Rework set_dabr so it can take a DABRX value as well
Rework set_dabr to take a DABRX value as well.
Both the pseries and PS3 hypervisors do some checks on the DABRX
values that are passed in the hcall. This patch stops bogus values
from being passed to hypervisor. Also, in the case where we are
clearing the breakpoint, where DABR and DABRX are zero, we modify the
DABRX value to make it valid so that the hcall won't fail.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:23 +0000 (22:44 +0000)]
powerpc/eeh: Cleanup on EEH PCI address cache
The patch does cleanup on EEH PCI address cache based on the fact
EEH core is the only user of the component.
* Cleanup on function names so that they all have prefix
"eeh" and looks more short.
* Function printk() has been replaced with pr_debug() or
pr_warning() accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:22 +0000 (22:44 +0000)]
powerpc/eeh: Trace eeh device from I/O cache
The idea comes from Benjamin Herrenschmidt. The eeh cache helps
fetching the pci device according to the given I/O address. Since
the eeh cache is serving for eeh, it's reasonable for eeh cache
to trace eeh device except pci device.
The patch make eeh cache to trace eeh device. Also, the major
eeh entry function eeh_dn_check_failure has been renamed to
eeh_dev_check_failure since it will take eeh device as input
parameter.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:21 +0000 (22:44 +0000)]
powerpc/eeh: Probe mode support
While EEH module is installed, PCI devices is checked one by one
to see if it supports eeh. On different platforms, the PCI devices
are referred through different ways when the EEH module is loaded.
For example, on pSeries platform, that is done by OF node. However,
we would do that by real PCI devices (struct pci_dev) on PowerNV
platform in future. So we needs some mechanism to differentiate
those cases by classifying them to probe modes, either from OF
nodes or real PCI devices.
The patch implements the support to eeh probe mode. Also, the
EEH on pSeries has set it into EEH_PROBE_MODE_DEVTREE. That means
the probe will be done based on OF nodes on pSeries platform.
In addition, On pSeries platform, it's done by OF nodes. The patch
moves the the probe function from EEH core to platform dependent
backend and some cleanup applied.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:20 +0000 (22:44 +0000)]
powerpc/eeh: Move stats to PE
The patch removes the eeh related statistics for eeh device since
they have been maintained by the corresponding eeh PE. Also, the
flags used to trace the state of eeh device and PE have been reworked
for a little bit.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:19 +0000 (22:44 +0000)]
powerpc/eeh: Handle EEH error based on PE
The patch reworks the current implementation so that the eeh errors
will be handled basing on PE instead of eeh device.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:18 +0000 (22:44 +0000)]
powerpc/eeh: Make EEH handler PE sensitive
Once eeh error is found, eeh event will be created and put it into
the global linked list. At the mean while, kernel thread will be
started to process it. The handler for the kernel thread originally
was eeh device sensitive.
The patch reworks the handler of the kernel thread so that it's PE
sensitive.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:17 +0000 (22:44 +0000)]
powerpc/eeh: Do reset based on PE
The patch implements reset based on PE instead of eeh device. Also,
The functions used to retrieve the reset type, either hot or fundamental
reset, have been reworked for a little bit. More specificly, it's
implemented based the the eeh device traverse function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:16 +0000 (22:44 +0000)]
powerpc/eeh: I/O enable and log retrival based on PE
The patch refactors the original implementation in order to enable
I/O and retrieve EEH log based on PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:15 +0000 (22:44 +0000)]
powerpc/eeh: Device bars restore based on PE
The patch introduces the function to traverse the devices of the
specified PE and its child PEs. Also, the restore on device bars
is implemented based on the traverse function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:14 +0000 (22:44 +0000)]
powerpc/eeh: Make EEH operations based on PE
Originally, all the EEH operations were implemented based on OF node.
Actually, it explicitly breaks the rules that the operation target
is PE instead of device. Therefore, the patch makes all the operations
based on PE instead of device.
Unfortunately, the backend for config space has to be kept as original
because it doesn't depend on PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:13 +0000 (22:44 +0000)]
powerpc/eeh: Trace error based on PE from beginning
There're 2 conditions to trigger EEH error detection: invalid value
returned from reading I/O or config space. On each case, the function
eeh_dn_check_failure will be called to initialize EEH event and put
it into the poll for further processing.
The patch changes the function for a little bit so that the EEH error
will be traced based on PE instead of EEH device any more. Also, the
function eeh_find_device_pe() has been removed since the eeh device
is tracing the PE by struct eeh_dev::pe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:12 +0000 (22:44 +0000)]
powerpc/eeh: Trace EEH state based on PE
Since we've introduced dedicated struct to trace individual PEs,
it's reasonable to trace its state through the dedicated struct
instead of using "eeh_dev" any more.
The patches implements the state tracing based on PE. It's notable
that the PE state will be applied to the specified PE as well as
its child PEs. That complies with the rule that problematic parent
PE will prevent those child PEs from working properly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:11 +0000 (22:44 +0000)]
powerpc/eeh: Build EEH event based on PE
The original implementation builds EEH event based on EEH device.
We already had dedicated struct to depict PE. It's reasonable to
build EEH event based on PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:10 +0000 (22:44 +0000)]
powerpc/eeh: Remove PE at appropriate time
During PCI hotplug and EEH recovery, the PE hierarchy tree might be
changed due to the PCI topology changes. At later point when the
PCI device is added, the PE will be created dynamically again.
The patch introduces new function to remove EEH devices from the
associated PE. That also can cause that the parent PE is removed
from the PE tree if the parent PE doesn't include valid EEH devices
and child PEs.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:09 +0000 (22:44 +0000)]
powerpc/eeh: Create PEs duing EEH initialization
The patch creates PEs and associated the newly created PEs with
it parent/silbing as well as EEH devices. It would become more
straight to trace EEH errors and recover them accordingly.
Once the EEH functionality on one PCI IOA has been enabled, we
tries to create PE against it. If there's existing PE, to which
the current PCI IOA should be attached, the existing PE will be
converted from "device" type to "bus" type accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:08 +0000 (22:44 +0000)]
powerpc/eeh: Search PE based on requirement
The patch implements searching PE based on the following
requirements:
* Search PE according to PE address, which is traditional
PE address that is composed of PCI bus/device/function
number, or unified PE address assigned by firmware or
platform.
* Search parent PE according to the given EEH device. It's
useful when creating new PE and put it into right position.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:07 +0000 (22:44 +0000)]
powerpc/eeh: Create PEs for PHBs
For one particular PE, it's only meaningful in the ancestor PHB
domain. Therefore, each PHB should have its own PE hierarchy tree
to trace those PEs created against the PHB.
The patch creates PEs for the PHBs and put those PEs into the
global link list traced by "eeh_phb_pe". The link list of PEs
would be first level of overall PE hierarchy tree across the
system.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:06 +0000 (22:44 +0000)]
powerpc/eeh: Introduce global mutex
The patch introduces global mutex for EEH so that the core data
structures can be protected by that. Also, 2 inline functions
are exported for that: eeh_lock() and eeh_unlock().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:05 +0000 (22:44 +0000)]
powerpc/eeh: Introduce eeh_pe struct
As defined in PAPR 2.4, Partitionable Endpoint (PE) is an I/O subtree
that can be treated as a unit for the purposes of partitioning and error
recovery. Therefore, eeh core should be aware of PE. With eeh_pe struct,
we can support PE explicitly. Further more, it makes all the stuff much
more data centralized. Another important reason is for eeh core to support
multiple platforms. Some of them like pSeries figures out PEs through
OF nodes while others like powernv have to do that through PCI bus/device
tree. With explicit PE support, eeh core will be implemented based on
the centrialized data and platform dependent implementations figure it
out by their feasible ways.
When the struct is designed, following factors are taken in account:
* Reflecting the relationships of PEs. PE might have parent
as well children.
* Reflecting the association of PE and (eeh) devices.
* PEs have PHB boundary.
* PE should have unique address assigned in the corresponding
PHB domain.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:04 +0000 (22:44 +0000)]
powerpc/eeh: More logs for EEH initialization
The patch adds more logs to EEH initialization functions for
debugging purpose. Also, the machine type (pSeries) is checked
in the platform initialization to assure it's the correct platform
to invoke it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:03 +0000 (22:44 +0000)]
powerpc/eeh: Use slab to allocate eeh devices
The EEH initialization functions have been postponed until slab/slub
are ready. So we use slab/slub to allocate the memory chunks for newly
creatd EEH devices. That would save lots of memory.
The patch also does cleanup to replace "kmalloc" with "kzalloc" so
that we needn't clear the allocated memory chunk explicitly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Fri, 7 Sep 2012 22:44:02 +0000 (22:44 +0000)]
powerpc/eeh: Move EEH initialization around
Currently, we have 3 phases for EEH initialization on pSeries platform.
All of them are done through builtin functions: platform initialization,
EEH device creation, and EEH subsystem enablement. All of them are done
no later than ppc_md.setup_arch. That means that the slab/slub isn't ready
yet, so we have to allocate memory chunks on basis of PAGE_SIZE for those
dynamically created EEH devices. That's pretty expensive.
In order to utilize slab/slub for memory allocation, we have to move the EEH
initialization functions around, but all of them should be called after slab
is ready.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Fri, 7 Sep 2012 15:31:44 +0000 (15:31 +0000)]
powerpc: Initialise paca.data_offset with poison
It's possible for the cpu_possible_mask to change between the time we
initialise the pacas and the time we setup per_cpu areas.
Obviously impossible cpus shouldn't ever be running, but stranger things
have happened. So be paranoid and initialise data_offset with a poison
value in case we don't set it up later.
Based on a patch from Anton Blanchard.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Sat, 8 Sep 2012 23:43:45 +0000 (16:43 -0700)]
Linux 3.6-rc5
Linus Torvalds [Sat, 8 Sep 2012 23:22:43 +0000 (16:22 -0700)]
Merge branch 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit
e9da6e9905e6 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
Linus Torvalds [Sat, 8 Sep 2012 23:20:59 +0000 (16:20 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for EMR on Cintiq 24HD touch
Input: i8042 - add Gigabyte T1005 series netbooks to noloop table
Input: imx_keypad - reset the hardware before enabling
Input: edt-ft5x06 - fix build error when compiling wthout CONFIG_DEBUG_FS
Linus Torvalds [Fri, 7 Sep 2012 19:29:38 +0000 (12:29 -0700)]
Merge branch 'upstream-fixes' of git://git./linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
"It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
performance improvement (not processing debug data if noone is
interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
work even with generic driver in a crippled mode, by Andres Freund."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
HID: Only dump input if someone is listening
HID: add NOGET quirk for Eaton Ellipse MAX UPS
Andres Freund [Thu, 30 Aug 2012 12:37:14 +0000 (14:37 +0200)]
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
c1dcad2d32d0252e8a3023d20311b52a187ecda3 added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Michael Neuling [Wed, 5 Sep 2012 19:17:49 +0000 (19:17 +0000)]
powerpc: Use the XDABR hcall
We never use the XDABR hcall since we check for DABR hcall first.
XDABR syscall is better since it allows us to also set the DABRX.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 5 Sep 2012 19:17:48 +0000 (19:17 +0000)]
powerpc: Use consistent name info for arch_hw_breakpoint
Change bp_info to info to be consistent with the rest of this file.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Wed, 5 Sep 2012 19:17:47 +0000 (19:17 +0000)]
powerpc: Pack arch_hw_breakpoint to avoid holes in struct
No functional change
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Suzuki Poulose [Tue, 21 Aug 2012 01:42:43 +0000 (01:42 +0000)]
powerpc: Export memory limit via device tree
The powerpc kernel doesn't export the memory limit enforced by 'mem='
kernel parameter. This is required for building the ELF header in
kexec-tools to limit the vmcore to capture only the used memory. On
powerpc the kexec-tools depends on the device-tree for memory related
information, unlike /proc/iomem on the x86.
Without this information, the kexec-tools assumes the entire System
RAM and vmcore creates an unnecessarily larger dump.
This patch exports the memory limit, if present, via
chosen/linux,memory-limit
property, so that the vmcore can be limited to the memory limit.
The prom_init seems to export this value in the same node. But doesn't
really
appear there. Also the memory_limit gets adjusted with the processing of
crashkernel= parameter. This patch makes sure we get the actual limit.
The kexec-tools will use the value to limit the 'end' of the memory
regions.
Tested this patch on ppc64 and ppc32(ppc440) with a kexec-tools
patch by Mahesh.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Tested-by: Mahesh J. Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Suzuki Poulose [Tue, 21 Aug 2012 01:42:33 +0000 (01:42 +0000)]
powerpc: Change memory_limit from phys_addr_t to unsigned long long
There are some device-tree nodes, whose values are of type phys_addr_t.
The phys_addr_t is variable sized based on the CONFIG_PHSY_T_64BIT.
Change these to a fixed unsigned long long for consistency.
This patch does the change only for memory_limit.
The following is a list of such variables which need the change:
1) kernel_end, crashk_size - in arch/powerpc/kernel/machine_kexec.c
2) (struct resource *)crashk_res.start - We could export a local static
variable from machine_kexec.c.
Changing the above values might break the kexec-tools. So, I will
fix kexec-tools first to handle the different sized values and then change
the above.
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Matthew McClintock [Thu, 6 Sep 2012 08:48:54 +0000 (08:48 +0000)]
powerpc: Fix build dependencies for c files requiring libfdt.h
Several files in obj-plat depend on libfdt header file. Sometimes
when building one can see the following issue. This patch adds
libfdt as dependency to those object files
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:854:1: error: unterminated comment
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:1:0: error: unterminated #ifndef
| BOOTCC arch/powerpc/boot/inffast.o
| make[1]: *** [arch/powerpc/boot/treeboot-iss4xx.o] Error 1
| make[1]: *** Waiting for unfinished jobs....
| BOOTCC arch/powerpc/boot/inflate.o
| make: *** [uImage] Error 2
| ERROR: oe_runmake failed
| ERROR: Function failed: do_compile (see /srv/home/pokybuild/yocto-autobuilder/yocto-slave/p1022ds/build/build/tmp/work/p1022ds-poky-linux-gnuspe/linux-qoriq-sdk-3.0.34-r5/temp/log.do_compile.2167 for further information)
NOTE: recipe linux-qoriq-sdk-3.0.34-r5: task do_compile: Failed
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Carl E. Love [Fri, 3 Aug 2012 03:02:17 +0000 (03:02 +0000)]
powerpc/oprofile: Fix marked events support on Power7+ not set.
Starting with Power 7+ we need to check for marked events if the SIAR
register is valid, i.e. it contains the correct address of the instruction
at the time the performance counter overflowed. The mmcra register on
Power 7+, contains a new bit to indicate that the contents of the SIAR
is valid. If the event is not marked, then the sample is recorded
independently of the SIAR valid bit setting. For older processors, there
is no SIAR valid bit to check so the samples are always recorded. This is
done by forcing the cntr_marked_events bit mask to zero. The code will
always record the sample in this case since the bit mask says the event is
not a marked event even if it really is a marked event.
Signed-off-by: Carl Love <cel@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
sukadev@linux.vnet.ibm.com [Mon, 16 Jul 2012 11:22:02 +0000 (11:22 +0000)]
powerpc: Define Power7+ PV constant PV_POWER7p
This definition will be used by subsequent perf and oprofile patches
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 4 Jun 2012 16:47:03 +0000 (16:47 +0000)]
powerpc/pseries: Round up MSI-X requests
The pseries firmware currently refuses any non power of two MSI-X
request. Unfortunately most network drivers end up asking for that
because they want a power of two for RX queues and one or two extra
for everything else.
This patch rounds up the firmware request to the next power of two
if the quota allows it. If this fails we fall back to using the
original request size.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Gavin Shan [Sun, 3 Jun 2012 22:15:25 +0000 (22:15 +0000)]
powerpc/pci: Save P2P bridge resource if possible
When PCI probe flag PCI_REASSIGN_ALL_RSRC has been passed into PCI
core, it's hoped that all resources to be reassigned by PCI core.
As to particular P2P (PCI-to-PCI) bridge, the size of the corresponding
BAR (I/O, MMIO, prefetchable MMIO) is calculated by the resources
required by the PCI devices behind the P2P bridge. That means that
the information like start/end address retrieved from the hardware
registers of the P2P bridge is meainingless in the case. However,
we still count that in and the BARs might have been configured by
firmware with non-zero size. That leads to space waste.
The patch explicitly sets the size of P2P bridge BARs to zero in
case that resource reassignment is expected with PCI probe flag
PCI_REASSIGN_ALL_RSRC. In the result, it will save overall resource
required by the system without waste.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Fri, 7 Sep 2012 00:16:42 +0000 (17:16 -0700)]
Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git./linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
* Fix for TLB flushing introduced in v3.6
* Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
in a 32-bit kernel we need to allocate for coherent pages from a
32-bit pool.
* When trying to re-use P2M nodes we had a one-off error and triggered
a BUG_ON check with specific CONFIG_ option.
* When doing FLR in Xen-PCI-backend we would first do FLR then save the
PCI configuration space. We needed to do it the other way around.
* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Fix proper FLR steps.
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
Linus Torvalds [Fri, 7 Sep 2012 00:15:49 +0000 (17:15 -0700)]
Merge tag '3.6-pci-fixes' of git://git./linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Power management
- PCI/PM: Enable D3/D3cold by default for most devices
- PCI/PM: Keep parent bridge active when probing device
- PCI/PM: Fix config reg access for D3cold and bridge suspending
- PCI/PM: Add ABI document for sysfs file d3cold_allowed
Core
- PCI: Don't print anything while decoding is disabled"
* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't print anything while decoding is disabled
PCI/PM: Add ABI document for sysfs file d3cold_allowed
PCI/PM: Fix config reg access for D3cold and bridge suspending
PCI/PM: Keep parent bridge active when probing device
PCI/PM: Enable D3/D3cold by default for most devices
Benjamin Herrenschmidt [Thu, 6 Sep 2012 23:48:59 +0000 (09:48 +1000)]
Merge branch 'merge' into next
Brings in various bug fixes from 3.6-rcX
Ananth N Mavinakayanahalli [Wed, 5 Sep 2012 22:17:04 +0000 (22:17 +0000)]
powerpc/kprobes: Rename opcode_t in probes.h to ppc_opcode_t
commit:
8b7b80b9ebb46dd88fbb94e918297295cf312b59
[24/29] powerpc: Uprobes port to powerpc
Caused a clash with the fore200e driver:
In file included from drivers/atm/fore200e.c:70:0:
drivers/atm/fore200e.h:263:3: error: redefinition of typedef 'opcode_t' with different type
arch/powerpc/include/asm/probes.h:25:13: note: previous declaration of 'opcode_t' was here
Fix the namespace clash by making opcode_t in probes.h to ppc_opcode_t.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mihai Caraman [Thu, 6 Sep 2012 02:49:44 +0000 (02:49 +0000)]
powerpc: Restore VDSO information on critical exception om BookE
Critical exception on 64-bit booke uses user-visible SPRG3 as scratch.
Restore VDSO information in SPRG3 on exception prolog.
Use a common sprg3 field in PACA for all powerpc64 architectures.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Thu, 6 Sep 2012 17:23:58 +0000 (10:23 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Olof Johansson:
"Mostly Renesas and Atmel bugfixes this time, targeting boot and build
problems. A couple of patches for gemini and kirkwood as well. On a
whole nothing very controversial."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: gemini: fix the gemini build
ARM: shmobile: armadillo800eva: enable rw rootfs mount
ARM: Kirkwood: Fix 'SZ_1M' undeclared here for
db88f6281-bp-setup.c
ARM: shmobile: mackerel: fixup usb module order
ARM: shmobile: armadillo800eva: fixup: sound card detection order
ARM: shmobile: marzen: fixup smsc911x id for regulator
ARM: at91/feature-removal-schedule: delay at91_mci removal
ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
ARM: at91/clock: fix PLLA overclock warning
ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
ARM: at91: fix system timer irq issue due to sparse irq support
ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc
Linus Torvalds [Thu, 6 Sep 2012 16:39:47 +0000 (09:39 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull a hwmon fix from Guenter Roeck:
"One patch, fixing DIV_ROUND_CLOSEST to support negative dividends.
While the changes are not in the drivers/hwmon directory, the problem
primarily affects hwmon drivers, and it makes sense to push the patch
through the hwmon tree."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends
Linus Torvalds [Thu, 6 Sep 2012 16:38:25 +0000 (09:38 -0700)]
Merge branch 'rc-fixes' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild fixes from Michal Marek:
"These are two fixes that should go into 3.6. The link-vmlinux.sh one
is obvious.
The other one fixes make firmware_install with certain configurations,
where a file in the toplevel firmware tree gets installed first, and
$(INSTALL_FW_PATH)/$$(dir <file>) results in /lib/firmware/./, which
confuses make 3.82 for some reason."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
firmware: fix directory creation rule matching with make 3.82
link-vmlinux.sh: Fix stray "echo" in error message
Dave Jones [Thu, 6 Sep 2012 16:01:00 +0000 (12:01 -0400)]
Remove user-triggerable BUG from mpol_to_str
Trivially triggerable, found by trinity:
kernel BUG at mm/mempolicy.c:2546!
Process trinity-child2 (pid: 23988, threadinfo
ffff88010197e000, task
ffff88007821a670)
Call Trace:
show_numa_map+0xd5/0x450
show_pid_numa_map+0x13/0x20
traverse+0xf2/0x230
seq_read+0x34b/0x3e0
vfs_read+0xac/0x180
sys_pread64+0xa2/0xc0
system_call_fastpath+0x1a/0x1f
RIP: mpol_to_str+0x156/0x360
Cc: stable@vger.kernel.org
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konrad Rzeszutek Wilk [Wed, 5 Sep 2012 20:35:20 +0000 (16:35 -0400)]
xen/pciback: Fix proper FLR steps.
When we do FLR and save PCI config we did it in the wrong order.
The end result was that if a PCI device was unbind from
its driver, then binded to xen-pciback, and then back to its
driver we would get:
> lspci -s 04:00.0
04:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
13:42:12 # 4 :~/
> echo "0000:04:00.0" > /sys/bus/pci/drivers/pciback/unbind
> modprobe e1000e
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:04:00.0: Disabling ASPM L0s L1
e1000e 0000:04:00.0: enabling device (0000 -> 0002)
xen: registering gsi 48 triggering 0 polarity 1
Already setup the GSI :48
e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e: probe of 0000:04:00.0 failed with error -2
This fixes it by first saving the PCI configuration space, then
doing the FLR.
Reported-by: Ren, Yongjie <yongjie.ren@intel.com>
Reported-and-Tested-by: Tobias Geiger <tobias.geiger@vido.info>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: stable@vger.kernel.org
Linus Torvalds [Thu, 6 Sep 2012 02:41:58 +0000 (19:41 -0700)]
Merge tag 'mmc-fixes-for-3.6-rc5' of git://git./linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- a firmware bug on several Samsung MoviNAND eMMC models causes
permanent corruption on the device when secure erase and secure trim
requests are made, so we disable those requests on these eMMC devices.
- atmel-mci: fix a hang with some SD cards by waiting for not-busy flag.
- dw_mmc: low-power mode breaks SDIO interrupts; fix PIO error handling;
fix handling of error interrupts.
- mxs-mmc: fix deadlocks; fix compile error due to dma.h arch change.
- omap: fix broken PIO mode causing memory corruption.
- sdhci-esdhc: fix card detection.
* tag 'mmc-fixes-for-3.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: omap: fix broken PIO mode
mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
mmc: dw_mmc: Disable low power mode if SDIO interrupts are used
mmc: dw_mmc: fix error handling in PIO mode
mmc: dw_mmc: correct mishandling error interrupt
mmc: dw_mmc: amend using error interrupt status
mmc: atmel-mci: not busy flag has also to be used for read operations
mmc: sdhci-esdhc: break out early if clock is 0
mmc: mxs-mmc: fix deadlock caused by recursion loop
mmc: mxs-mmc: fix deadlock in SDIO IRQ case
mmc: bfin_sdh: fix dma_desc_array build error
Miklos Szeredi [Wed, 5 Sep 2012 16:38:50 +0000 (18:38 +0200)]
uml: fix compile error in deliver_alarm()
Fix the following compile error on UML.
arch/um/os-Linux/time.c: In function 'deliver_alarm':
arch/um/os-Linux/time.c:117:3: error: too few arguments to function 'alarm_handler'
arch/um/os-Linux/internal.h:1:6: note: declared here
The error was introduced by commit
d3c1cfcd ("um: pass siginfo to guest
process") in 3.6-rc1.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: Martin Pärtel <martin.partel@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 4 Sep 2012 14:10:08 +0000 (15:10 +0100)]
dj: memory scribble in logi_dj
Allocate a structure not a pointer to it !
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 6 Sep 2012 01:41:32 +0000 (18:41 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few fixes for 3.6 that were piling up while I was away or
busy (I was mostly MIA a week or two before San Diego).
Some fixes from Anton fixing up issues with our relatively new DSCR
control feature, and a few other fixes that are either regressions or
bugs nasty enough to warrant not waiting."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
Linus Torvalds [Thu, 6 Sep 2012 01:40:12 +0000 (18:40 -0700)]
Merge tag 'gpio-fixes-for-v3.6' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"These are some GPIO regression fixes for v3.6:
- Erroneous debug message from of_get_named_gpio_flags()
- Make sure the MC9S08DZ60 GPIO driver depend on I2C being compiled
in (not module) or allmodconfig breaks.
- Check return value from irq_alloc_descs() in the Emma Mobile GPIO
driver.
- Assign the owner field for the rdc321x driver so the module won't
be removed if it has active GPIOs."
* tag 'gpio-fixes-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rdc321x: Prevent removal of modules exporting active GPIOs
gpio: em: Fix checking return value of irq_alloc_descs
gpio: mc9s08dz60: Fix build error if I2C=m
gpio: Fix debug message in of_get_named_gpio_flags()
Linus Torvalds [Thu, 6 Sep 2012 01:38:52 +0000 (18:38 -0700)]
Merge tag 'sound-3.6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There are nothing scaring, contains only small fixes for HD-audio and
USB-audio:
- EPSS regression fix and GPIO fix for HD-audio IDT codecs
- A series of USB-audio regression fixes that are found since 3.5
kernel"
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: snd-usb: fix cross-interface streaming devices
ALSA: snd-usb: fix calls to next_packet_size
ALSA: snd-usb: restore delay information
ALSA: snd-usb: use list_for_each_safe for endpoint resources
ALSA: snd-usb: Fix URB cancellation at stream start
ALSA: hda - Don't trust codec EPSS bit for IDT 92HD83xx & co
ALSA: hda - Avoid unnecessary parameter read for EPSS
ALSA: hda - Do not set GPIOs for speakers on IDT if there are no speakers
Linus Torvalds [Thu, 6 Sep 2012 01:38:02 +0000 (18:38 -0700)]
Merge tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- a fix by Paul Cercueil to prevent a possible buffer overflow
- a fix by Bruno Prémont to prevent a rare sleep in invalid context
- a fix by Julia Lawall for a double free in auo_k190x
- a fix by Dan Carpenter to prevent a division by zero in mb862xxfb
- a regression fix by Tomi Valkeinen for the SDI output in OMAP
- a fix by Grazvydas Ignotas to fix the console colors in OMAP
* tag 'fbdev-fixes-for-3.6-1' of git://github.com/schandinat/linux-2.6:
OMAPFB: fix framebuffer console colors
OMAPDSS: Fix SDI PLL locking
video: mb862xxfb: prevent divide by zero bug
drivers/video/auo_k190x.c: drop kfree of devm_kzalloc's data
fbcon: Fix bit_putcs() call to kmalloc(s, GFP_KERNEL)
fbcon: prevent possible buffer overflow.
Linus Torvalds [Thu, 6 Sep 2012 01:37:16 +0000 (18:37 -0700)]
Merge tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi
Pull ubi fix from Artem Bityutskiy:
"A single small fix for memory deallocation: we allocated memory using
'kmem_cache_alloc()' but were freeing it using 'kfree()' in some
cases. Now we fix this by using 'kmem_cache_free()' instead."
* tag 'upstream-3.6-rc5' of git://git.infradead.org/linux-ubi:
UBI: fix a horrible memory deallocation bug
Mikulas Patocka [Sat, 1 Sep 2012 16:34:07 +0000 (12:34 -0400)]
Fix order of arguments to compat_put_time[spec|val]
Commit
644595f89620 ("compat: Handle COMPAT_USE_64BIT_TIME in
net/socket.c") introduced a bug where the helper functions to take
either a 64-bit or compat time[spec|val] got the arguments in the wrong
order, passing the kernel stack pointer off as a user pointer (and vice
versa).
Because of the user address range check, that in turn then causes an
EFAULT due to the user pointer range checking failing for the kernel
address. Incorrectly resuling in a failed system call for 32-bit
processes with a 64-bit kernel.
On odder architectures like HP-PA (with separate user/kernel address
spaces), it can be used read kernel memory.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.051494 seconds and 5 git commands to generate.