Lu, Han [Thu, 19 Nov 2015 15:25:13 +0000 (23:25 +0800)]
ALSA: hda - apply SKL display power request/release patch to BXT
For SKL, only the HDMI codec is in the display power well while the
HD-A controller isn't. So the codec flag 'link_power_control' is
set to request/release the display power via bus link_power ops.
For BXT, the power well design is the same as SKL, so the patch
should be applied to BXT too.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lu, Han [Thu, 19 Nov 2015 15:25:12 +0000 (23:25 +0800)]
ALSA: hda - add PCI IDs for Intel Broxton
Add HD Audio Device PCI ID for the Intel Broxton platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Sun, 15 Nov 2015 21:39:08 +0000 (22:39 +0100)]
ALSA: usb-audio: work around CH345 input SysEx corruption
One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4. For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:
correct: CH345:
0F FE 00 00 0F FE 00 00
04 F0 01 02 04 F0 01 02
04 03 04 05 0F 03 04 05
04 06 07 08 04 06 07 08
04 09 0A 0B 0F 09 0A 0B
04 0C 0D 0E 04 0C 0D 0E
05 F7 00 00 05 F7 00 00
A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored. The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".
These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.
(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Sun, 15 Nov 2015 21:38:29 +0000 (22:38 +0100)]
ALSA: usb-audio: prevent CH345 multiport output SysEx corruption
The CH345 USB MIDI chip has two output ports. However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.
It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port. So we can just ignore the device's
descriptors, and hardcode one output port.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Sun, 15 Nov 2015 21:37:44 +0000 (22:37 +0100)]
ALSA: usb-audio: add packet size quirk for the Medeli DD305
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto [Sat, 14 Nov 2015 07:42:04 +0000 (16:42 +0900)]
ALSA: dice: fix detection of Loud devices
Commit
a471fcde8c2c ("ALSA: dice: fix detection of Weiss devices") adds
a quirk of Weiss models. According to users' reports, Loud models also
have the similar quirk. They have 0x10 in the category field.
This commit adds support for Mackie Onyx Blackbird and Onyx-i series.
As long as I know, Dice-based models produced by
Focusrite/Alesis/PreSonus/M-Audio/TC Electronic have default value (0x04)
in their category field, thus it may be reasonable to add a condition
statement for Loud models, instead of removing the check of category value.
Reported-by: Rouge Etienne <erouge.externe@m6.fr>
Reported-by: Etilem <contact@etilem.net>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Sat, 14 Nov 2015 16:46:31 +0000 (17:46 +0100)]
ALSA: hda - Fix noise on Dell Latitude E6440
Dell Latitude E6440 (1028:05bd) needs the same fixup as applied to
other Latitude E7xxx models for the click noise due to the recent
power-saving changes.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=954876
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Williams [Thu, 12 Nov 2015 20:13:57 +0000 (12:13 -0800)]
ALSA: pci: depend on ZONE_DMA
There are several sound drivers that 'select ZONE_DMA'. This is
backwards as ZONE_DMA is an architecture capability exported to drivers.
Switch the polarity of the dependency to disable these drivers when the
architecture does not support ZONE_DMA. This was discovered in the
context of testing/enabling devm_memremap_pages() which depends on
ZONE_DEVICE. ZONE_DEVICE in turn depends on !ZONE_DMA.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Thu, 12 Nov 2015 10:52:13 +0000 (11:52 +0100)]
ALSA: hda - Simplify phantom jack handling for HDMI/DP
The HDMI codec parser may create a phantom jack, but the helper
function snd_hda_jack_add_kctl() treats always as a normal jack. This
is superfluous as the jack query is executed at each time the jack
sync is performed.
Since the HDMI codec parser is the only caller of this function, it's
easier to change back this directly calling the original
__snd_hda_jack_add_kctl() with phantom_jack parameter.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lu, Han [Wed, 11 Nov 2015 08:54:27 +0000 (16:54 +0800)]
ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
Broxton and Skylake have the same behavior on display audio. So this patch
applys Skylake fix-ups to Broxton.
Signed-off-by: Lu, Han <han.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Julia Lawall [Sun, 8 Nov 2015 22:40:41 +0000 (23:40 +0100)]
ALSA: ctxfi: constify rsc ops structures
The various rsc ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jurgen Kramer [Mon, 9 Nov 2015 11:13:55 +0000 (12:13 +0100)]
ALSA: usb: Add native DSD support for Aune X1S
This patch adds native DSD support for the Aune X1S 32BIT/384 DSD DAC
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto [Sun, 8 Nov 2015 05:46:34 +0000 (14:46 +0900)]
ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
A commit to add support for this model should have added a comment
about this model to Kconfig.
Fixes: 759a2f40c9fa('ALSA: oxfw: add an entry for TASCAM FireOne')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alexey Khoroshilov [Fri, 6 Nov 2015 22:56:05 +0000 (01:56 +0300)]
sound: fix check for error condition of register_chrdev()
init_oss_soundcore() compares returned value of register_chrdev()
with -1, while other error codes can be returned.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alexandra Yates [Wed, 4 Nov 2015 23:56:09 +0000 (15:56 -0800)]
ALSA: hda - Add Intel Lewisburg device IDs Audio
Adding Intel codename Lewisburg platform device IDs for audio.
[rearranged the position by tiwai]
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 4 Nov 2015 21:39:16 +0000 (22:39 +0100)]
ALSA: hda - Apply pin fixup for HP ProBook 6550b
HP ProBook 6550b needs the same pin fixup applied to other HP B-series
laptops with docks for making its headphone and dock headphone jacks
working properly. We just need to add the codec SSID to the list.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=191971
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 2 Nov 2015 16:35:34 +0000 (17:35 +0100)]
ALSA: hda - Fix lost 4k BDL boundary workaround
During the migration to HDA core code, we lost the workaround for 4k
BDL boundary. The flag exists in the new hdac_bus, but it's never
set. This resulted in the sudden sound stall on some controllers that
require this workaround like Creative Recon3D.
This patch fixes the issue by setting the flag for such controllers
properly.
Fixes: ccc98865aa44 ('ALSA: hda - Migrate more hdac_stream codes')
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 2 Nov 2015 08:00:37 +0000 (09:00 +0100)]
Merge branch 'for-next' into for-linus
Ondrej Zary [Sun, 1 Nov 2015 19:53:14 +0000 (20:53 +0100)]
ALSA: maestro3: Fix Allegro mute until master volume/mute is touched
ESS Allegro (marked ES1989S), [125d:1988] (rev 10) is mute after
loading snd-maestro3 and running alsactl restore. Touching master
volume or mute makes it work.
Looks like a bug in the AC'97 codec integrated into the chip.
Write AC97_MASTER register twice to work-around the problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ondrej Zary [Sun, 1 Nov 2015 13:32:03 +0000 (14:32 +0100)]
ALSA: maestro3: Enable docking support for Dell Latitude C810
Enable I2S docking for Dell Latitude C810.
This allows the audio output on C/Port II to work (and probably also
the audio inputs on C/Dock II).
The volume can't be adjusted - none of the mixer controls currently
supported affects the I2S output (they belong to the STAC9721/23 AC'97
codec responsible for the laptop internal connectors & speakers).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto [Fri, 30 Oct 2015 17:43:16 +0000 (02:43 +0900)]
ALSA: firewire-digi00x: add another rawmidi character device for MIDI control ports
Digi 002/003 family uses two ways to transfer MIDI messages. They're
different mechanisms, while it's better to handle the ways in different
ALSA rawmidi character devices because one character device has just a
set of operations.
This commit adds another rawmidi character device for control MIDI port. As
a result, first rawmidi character device is just for MIDI messages
transferred by isochronous packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto [Fri, 30 Oct 2015 17:43:15 +0000 (02:43 +0900)]
ALSA: firewire-digi00x: add MIDI operations for MIDI control port
Digi 002/003 family has two types of MIDI port; one is for physical MIDI
port and another is for MIDI control message. The former is transferred in
isochronous packet, and the latter is transferred by asynchronous
transaction. These transmission mechanisms are completely different, while
current ALSA digi00x driver defines a set of operations for them with
several condition statements. As a result, codes for the operation are
messy.
This commit adds a set of MIDI operation for control MIDI ports. In later
commit, it's applied as an operation for ALSA rawmidi character device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto [Fri, 30 Oct 2015 17:43:14 +0000 (02:43 +0900)]
ALSA: firewire-digi00x: rename identifiers of MIDI operation for physical ports
In following commit, new functions and variables are added for operations
of MIDI control port.
This commit is a preparation. Current identifiers are renamed so that they
mean physical MIDI ports.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ondrej Zary [Thu, 29 Oct 2015 19:52:24 +0000 (20:52 +0100)]
ALSA: cs46xx: Fix suspend for all channels
snd_cs46xx_suspend() is missing snd_pcm_suspend_all calls for pcm_rear,
pcm_center_lfe and pcm_iec958.
There's also a copy/paste bug in snd_cs46xx_pcm_iec958(), overwriting
pcm_rear in struct snd_cs46xx, leaving pcm_iec958 unused.
Fix all this to allow all channels to survive suspend/resume.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ondrej Zary [Thu, 29 Oct 2015 19:22:06 +0000 (20:22 +0100)]
ALSA: cs46xx: Fix Duplicate front for CS4294 and CS4298 codecs
Currently, the Duplicate front control is enabled only for two specific
revisions of CS4294.
Enable it for all CS4294 and CS4298 codecs instead.
This fixes rear output on my VC-4620N sound card
(CS4620 + CS4298 rev.5).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 28 Oct 2015 11:33:48 +0000 (12:33 +0100)]
ALSA: DocBook: Add soc-ops.c and soc-compress.c
These have been missing in the template file although they provide
good kernel doc comments. Let's add them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 28 Oct 2015 11:26:48 +0000 (12:26 +0100)]
ALSA: hda - Add / fix kernel doc comments
Give some readable comment in kernel doc style for each exported
function, as I promised in the previous meetings. While we're at it,
fix the wrong comments, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lars-Peter Clausen [Wed, 28 Oct 2015 10:37:53 +0000 (11:37 +0100)]
ALSA: Constify ratden/ratnum constraints
The ALSA core does not modify the constraints provided by a driver. Most
constraint helper functions already take a const pointer to the constraint
description, the exception at the moment being the ratden and ratnum
constraints. Make those const as well, this allows a driver to declare them
as const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Tue, 27 Oct 2015 13:21:51 +0000 (14:21 +0100)]
ALSA: hda - Disable 64bit address for Creative HDA controllers
We've had many reports that some Creative sound cards with CA0132
don't work well. Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used. All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.
This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries. I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.
Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too. So
the flag is applied to all Creative entries.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang [Mon, 26 Oct 2015 07:37:39 +0000 (15:37 +0800)]
ALSA: hda/realtek - Dell XPS one ALC3260 speaker no sound after resume back
This machine had I2S codec for speaker output.
It need to refill the I2S codec initial verb after resume back.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Reported-and-tested-by: George Gugulea <gugulea@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 26 Oct 2015 15:54:16 +0000 (16:54 +0100)]
ALSA: hda/ca0132 - Convert leftover pr_info() and pr_err()
Use codec_*() macro instead of pr_*() for improving the log
information. The current form even slips from alsa-info.sh.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 26 Oct 2015 07:32:46 +0000 (08:32 +0100)]
Merge tag 'asoc-v4.3-rc6' of git://git./linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.4
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
- A new driver for the Atmel Class D speaker drivers
Mark Brown [Mon, 26 Oct 2015 02:16:20 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/wm8904', 'asoc/topic/wm8955' and 'asoc/topic/wm8960' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:18 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/topology', 'asoc/topic/wm2000', 'asoc/topic/wm8731' and 'asoc/topic/wm8903' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:16 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/ssm2518' and 'asoc/topic/sunxi' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:13 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/rt298', 'asoc/topic/rt5640', 'asoc/topic/samsung' and 'asoc/topic/sh' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:10 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/rcar', 'asoc/topic/rl6347a', 'asoc/topic/rockchip' and 'asoc/topic/rt286' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:08 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/nau8825' and 'asoc/topic/pxa' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:06 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/imx' and 'asoc/topic/intel' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:03 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/dwc', 'asoc/topic/es8328', 'asoc/topic/fsl' and 'asoc/topic/fsl-card' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:02 +0000 (11:16 +0900)]
Merge remote-tracking branch 'asoc/topic/da7219' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:16:00 +0000 (11:16 +0900)]
Merge remote-tracking branches 'asoc/topic/atmel-classd' and 'asoc/topic/da7213' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:15:58 +0000 (11:15 +0900)]
Merge remote-tracking branches 'asoc/topic/ad193x' and 'asoc/topic/arizona' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:15:58 +0000 (11:15 +0900)]
Merge remote-tracking branch 'asoc/topic/rt5645' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:15:57 +0000 (11:15 +0900)]
Merge remote-tracking branch 'asoc/topic/doc' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:15:56 +0000 (11:15 +0900)]
Merge remote-tracking branch 'asoc/topic/dapm' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:15:55 +0000 (11:15 +0900)]
Merge remote-tracking branch 'asoc/topic/core' into asoc-next
Mark Brown [Mon, 26 Oct 2015 02:15:54 +0000 (11:15 +0900)]
Merge tag 'asoc-v4.3-rc2' into asoc-next
ASoC: Updates for v4.4
A first batch of updates targetted at v4.4. There are no substantial
core fixes here, the biggest block of changes is updates to the rcar
drivers and the addition of a CODEC driver for the AK4613.
# gpg: Signature made Fri 25 Sep 2015 05:37:06 KST using RSA key ID
5D5487D0
# gpg: key
CD7BEEBC: no public key for trusted key - skipped
# gpg: key
CD7BEEBC marked as ultimately trusted
# gpg: key
AF88CD16: no public key for trusted key - skipped
# gpg: key
AF88CD16 marked as ultimately trusted
# gpg: key
16005C11: no public key for trusted key - skipped
# gpg: key
16005C11 marked as ultimately trusted
# gpg: key
5621E907: no public key for trusted key - skipped
# gpg: key
5621E907 marked as ultimately trusted
# gpg: key
5C6153AD: no public key for trusted key - skipped
# gpg: key
5C6153AD marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Nicolin Chen [Thu, 22 Oct 2015 22:56:40 +0000 (15:56 -0700)]
ASoC: fsl: Use #ifdef instead of #if for CONFIG_PM_SLEEP
Change them to #ifdef as CONFIG_PM_SLEEP might not be defined at all.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Mon, 26 Oct 2015 02:07:40 +0000 (11:07 +0900)]
Merge branch 'topic/fsl-mega-fast' of git://git./linux/kernel/git/broonie/sound into asoc-fsl
Axel Lin [Sat, 24 Oct 2015 06:55:41 +0000 (14:55 +0800)]
ASoC: rt5645: Sort the order for register bit defines
So we have consistent order for register bit defines.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Sun, 25 Oct 2015 01:39:47 +0000 (10:39 +0900)]
Linux 4.3-rc7
Linus Torvalds [Fri, 23 Oct 2015 22:52:59 +0000 (07:52 +0900)]
Merge tag 'usb-4.3-rc7' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are three xhci driver fixes for reported issues for 4.3-rc7
All have been in linux-next for a while with no problems"
* tag 'usb-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Add spurious wakeup quirk for LynxPoint-LP controllers
xhci: handle no ping response error properly
xhci: don't finish a TD if we get a short transfer event mid TD
Linus Torvalds [Fri, 23 Oct 2015 22:52:09 +0000 (07:52 +0900)]
Merge tag 'tty-4.3-rc7' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two fixes that resolve reported issues, one with the 8250
driver, and the other with the generic fbcon driver.
Both have been in linux-next for a while"
* tag 'tty-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fbcon: initialize blink interval before calling fb_set_par
Revert "serial: 8250_dma: don't bother DMA with small transfers"
Linus Torvalds [Fri, 23 Oct 2015 22:51:13 +0000 (07:51 +0900)]
Merge tag 'staging-4.3-rc7' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are four iio driver fixes for 4.3-rc7, fixing some reported
issues. All of these have been in linux-next for a while"
* tag 'staging-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: mxs-lradc: Fix temperature offset
iio: accel: sca3000: memory corruption in sca3000_read_first_n_hw_rb()
iio: st_accel: fix interrupt handling on LIS3LV02
iio: adc: twl4030: Fix ADC[3:6] readings
Linus Torvalds [Fri, 23 Oct 2015 22:28:05 +0000 (07:28 +0900)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull infiniband fixes from Doug Ledford:
"It's late in the game, I know, but these fixes seemed important enough
to warrant a late pull request. They all involve oopses or use after
frees or corruptions.
Six serious fixes:
- Hold the mutex around the find and corresponding update of our gid
- The ifa list is rcu protected, copy its contents under rcu to avoid
using a freed structure
- On error, netdev might be null, so check it before trying to
release it
- On init, if workqueue alloc fails, fail init
- The new demux patches exposed a bug in mlx5 and ipath drivers, we
need to use the payload P_Key to determine the P_Key the packet
arrived on because the hardware doesn't tell us the truth
- Due to a couple convoluted error flows, it is possible for the CM
to trigger a use_after_free and a double_free of rb nodes. Add two
checks to prevent that. This code has worked for 10+ years. It is
likely that some of the recent changes have caused this issue to
surface. The current patch will protect us from nasty events for
now while we track down why this is just now showing up"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/cm: Fix rb-tree duplicate free and use-after-free
IB/cma: Use inner P_Key to determine netdev
IB/ucma: check workqueue allocation before usage
IB/cma: Potential NULL dereference in cma_id_from_event
IB/core: Fix use after free of ifa
IB/core: Fix memory corruption in ib_cache_gid_set_default_gid
Linus Torvalds [Fri, 23 Oct 2015 22:23:52 +0000 (07:23 +0900)]
Merge tag 'dm-4.3-fixes-4' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Three stable fixes (two in btree code used by DM thinp and one to
properly store flags in DM cache metadata's superblock)"
* tag 'dm-4.3-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: the CLEAN_SHUTDOWN flag was not being set
dm btree: fix leak of bufio-backed block in btree_split_beneath error path
dm btree remove: fix a bug when rebalancing nodes after removal
Linus Torvalds [Fri, 23 Oct 2015 22:20:57 +0000 (07:20 +0900)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"A final set of fixes for 4.3.
It is (again) bigger than I would have liked, but it's all been
through the testing mill and has been carefully reviewed by multiple
parties. Each fix is either a regression fix for this cycle, or is
marked stable. You can scold me at KS. The pull request contains:
- Three simple fixes for NVMe, fixing regressions since 4.3. From
Arnd, Christoph, and Keith.
- A single xen-blkfront fix from Cathy, fixing a NULL dereference if
an error is returned through the staste change callback.
- Fixup for some bad/sloppy code in nbd that got introduced earlier
in this cycle. From Markus Pargmann.
- A blk-mq tagset use-after-free fix from Junichi.
- A backing device lifetime fix from Tejun, fixing a crash.
- And finally, a set of regression/stable fixes for cgroup writeback
from Tejun"
* 'for-linus' of git://git.kernel.dk/linux-block:
writeback: remove broken rbtree_postorder_for_each_entry_safe() usage in cgwb_bdi_destroy()
NVMe: Fix memory leak on retried commands
block: don't release bdi while request_queue has live references
nvme: use an integer value to Linux errno values
blk-mq: fix use-after-free in blk_mq_free_tag_set()
nvme: fix 32-bit build warning
writeback: fix incorrect calculation of available memory for memcg domains
writeback: memcg dirty_throttle_control should be initialized with wb->memcg_completions
writeback: bdi_writeback iteration must not skip dying ones
writeback: fix bdi_writeback iteration in wakeup_dirtytime_writeback()
writeback: laptop_mode_timer_fn() needs rcu_read_lock() around bdi_writeback iteration
nbd: Add locking for tasks
xen-blkfront: check for null drvdata in blkback_changed (XenbusStateClosing)
Linus Torvalds [Fri, 23 Oct 2015 22:19:33 +0000 (07:19 +0900)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Two fixes.
One is a stopgap to prevent a stack blowout when users have a deep
chain of image clones. (We'll rewrite this code to be non-recursive
for the next window, but in the meantime this is a simple fix that
avoids a crash.)
The second fixes a refcount underflow"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: prevent kernel stack blow up on rbd map
rbd: don't leak parent_spec in rbd_dev_probe_parent()
Linus Torvalds [Fri, 23 Oct 2015 22:17:58 +0000 (07:17 +0900)]
Merge branch 'for-linus-4.3' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I have two more small fixes this week:
Qu's fix avoids unneeded COW during fallocate, and Christian found a
memory leak in the error handling of an earlier fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix possible leak in btrfs_ioctl_balance()
btrfs: Avoid truncate tailing page if fallocate range doesn't exceed inode size
Maruthi Srinivas Bayyavarapu [Fri, 23 Oct 2015 21:15:41 +0000 (17:15 -0400)]
ASoC: dwc: add check for master/slave format
DW i2s controller's master/slave config can be read from a
read-only register. Machine driver can try to set a master/slave
format on cpu-dai using 'set_fmt' of dai ops. A check is added to
verify codec is master when dwc is slave and vice-versa.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Joe Thornber [Thu, 22 Oct 2015 17:10:55 +0000 (18:10 +0100)]
dm cache: the CLEAN_SHUTDOWN flag was not being set
If the CLEAN_SHUTDOWN flag is not set when a cache is loaded then all cache
blocks are marked as dirty and a full writeback occurs.
__commit_transaction() is responsible for setting/clearing
CLEAN_SHUTDOWN (based the flags_mutator that is passed in).
Fix this issue, of the cache's on-disk flags being wrong, by making sure
__commit_transaction() does not reset the flags after the mutator has
altered the flags in preparation for them being serialized to disk.
before:
sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
disk_super->flags = cpu_to_le32(cmd->flags);
after:
disk_super->flags = cpu_to_le32(cmd->flags);
sb_flags = mutator(le32_to_cpu(disk_super->flags));
disk_super->flags = cpu_to_le32(sb_flags);
Reported-by: Bogdan Vasiliev <bogdan.vasiliev@gmail.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Mike Snitzer [Thu, 22 Oct 2015 14:56:40 +0000 (10:56 -0400)]
dm btree: fix leak of bufio-backed block in btree_split_beneath error path
btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.
Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <thornber@redhat.com>
Cc: stable@vger.kernel.org
Joe Thornber [Wed, 21 Oct 2015 17:36:49 +0000 (18:36 +0100)]
dm btree remove: fix a bug when rebalancing nodes after removal
Commit
4c7e309340ff ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().
The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them. If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.
Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.
Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.c
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Oder Chiou [Fri, 23 Oct 2015 06:05:53 +0000 (14:05 +0800)]
ASoC: rt5645: Add the HWEQ for the speaker output
The patch adds the HWEQ function for the speaker output. User can set the
HWEQ parameters using the ALSA binary control byte-by-byte. We use the
following struct array to store the HWEQ parameters for implementing as
simple as possible.
struct rt5645_eq_param_s {
unsigned short reg;
unsigned short val;
};
It supports the variant length of the HWEQ parameters that are required.
We add the validating function in the function "rt5645_hweq_put" of the
ALSA binary control to avoid the user that puts the invalid parameters.
In the HWEQ enable function of speaker event, we also add the validating
function to prevent that the invalid parameters are applied to codec.
The HWEQ parameters should be controlled by DAPM for a specific sequence,
so the parameters will be applied to the codec in the speaker power up
event of DAPM, and will be disabled in the speaker power down event of
DAPM.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ilya Dryomov [Sun, 11 Oct 2015 17:38:00 +0000 (19:38 +0200)]
rbd: prevent kernel stack blow up on rbd map
Mapping an image with a long parent chain (e.g. image foo, whose parent
is bar, whose parent is baz, etc) currently leads to a kernel stack
overflow, due to the following recursion in the reply path:
rbd_osd_req_callback()
rbd_obj_request_complete()
rbd_img_obj_callback()
rbd_img_parent_read_callback()
rbd_obj_request_complete()
...
Limit the parent chain to 16 images, which is ~5K worth of stack. When
the above recursion is eliminated, this limit can be lifted.
Fixes: http://tracker.ceph.com/issues/12538
Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 4.2
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Ilya Dryomov [Sun, 11 Oct 2015 17:38:00 +0000 (19:38 +0200)]
rbd: don't leak parent_spec in rbd_dev_probe_parent()
Currently we leak parent_spec and trigger a "parent reference
underflow" warning if rbd_dev_create() in rbd_dev_probe_parent() fails.
The problem is we take the !parent out_err branch and that only drops
refcounts; parent_spec that would've been freed had we called
rbd_dev_unparent() remains and triggers rbd_warn() in
rbd_dev_parent_put() - at that point we have parent_spec != NULL and
parent_ref == 0, so counter ends up being -1 after the decrement.
Redo rbd_dev_probe_parent() to fix this.
Cc: stable@vger.kernel.org # 3.10+, needs backporting for < 4.2
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Jeeja KP [Thu, 22 Oct 2015 17:52:42 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Add support to topology for module static pin
Some module pin connection are static and defined by the topology.
This patch adds support for static pin definitions in topology widget
private data
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Thu, 22 Oct 2015 17:52:41 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Fix to set Non gateway copier cfg
If copier instance is connected to a DMA gateway then driver
needs to configure the gateway configuration otherwise set
it to invalid.
This patch sets the non gateway copier node value to invalid.
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Thu, 22 Oct 2015 17:52:40 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Fix to check return value of dsp init
If DSP initialization fails, ipc to disable notification
will cause NULL ptr exception as ipc is not initialized.
This patch returns error if dsp init fails before
sending disable notification ipc.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Thu, 22 Oct 2015 17:52:39 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Add support to disable module notifications
Each FW modules can report underrun/overrun notification from
all modules. This patch disables underrun/overrun notification after
firmware is loaded.
This will be supportted for debug mode only thru debugfs
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Thu, 22 Oct 2015 17:52:38 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Update for ssp node index in copier cfg
DSP firmware has interface change for SSP node index structure.
New FW interface removes the dual_mono field and adds 4 bits for
TDM slot group index. This patch updates the ssp dma to align with
the DSP firmware structure.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Subhransu S. Prusty [Thu, 22 Oct 2015 17:52:37 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Fix to fill all sink/source pipe params
Currently params only for first copier widget identified in the
source/sink path is queried from NHLT. In the dapm route the
playback/capture widget may be connected to more than one copier
widget. This patch adds return check to return only for any error
case.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Subhransu S. Prusty [Thu, 22 Oct 2015 17:52:36 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Fix to use correct macros for the path iteration
In case of playback, for the BE dai source path should be iterated to find
the pipe params. With sink path iterated, this resulted in a loop and kernel
panic with page request failure.
Similar are the cases for Capture and FE dais. Using correct macros to fix
the panic
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Thu, 22 Oct 2015 17:52:35 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Remove BE copier blob memcpy
The BE copier private data allowed endpoint configuration blobs, now these
are queried from BIOS, we don't need to copy the blob, but only capability.
Removing the blob from private data will not allocate memory for module
specific config in which case memcpy will fail. Fix is to assign the ptr
queried from the NHLT table for the endpoint configuration.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jeeja KP [Thu, 22 Oct 2015 17:52:34 +0000 (23:22 +0530)]
ASoC: Intel: Skylake: Fix return for pm_runtime_get_sync()
pm_runtime_get_sync() will return a negative value in case of
error and can return postive value for success. The return check
for pm_runtime_get_sync() must be less than 0, so fix it
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Fri, 23 Oct 2015 13:34:32 +0000 (22:34 +0900)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two KASAN fixes, two EFI boot fixes, two boot-delay
optimization fixes, and a fix for a IRQ handling hang observed on
virtual platforms"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm, kasan: Silence KASAN warnings in get_wchan()
compiler, atomics, kasan: Provide READ_ONCE_NOCHECK()
x86, kasan: Fix build failure on KASAN=y && KMEMCHECK=y kernels
x86/smpboot: Fix CPU #1 boot timeout
x86/smpboot: Fix cpu_init_udelay=10000 corner case boot parameter misbehavior
x86/ioapic: Disable interrupts when re-routing legacy IRQs
x86/setup: Extend low identity map to cover whole kernel range
x86/efi: Fix multiple GOP device support
Linus Torvalds [Fri, 23 Oct 2015 13:31:39 +0000 (22:31 +0900)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes all around the map: an instrumentation fix, a nohz
usability fix, a lockdep annotation fix and two task group scheduling
fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Add missing lockdep_unpin() annotations
sched/deadline: Fix migration of SCHED_DEADLINE tasks
nohz: Revert "nohz: Set isolcpus when nohz_full is set"
sched/fair: Update task group's load_avg after task migration
sched/fair: Fix overly small weight for interactive group entities
sched, tracing: Stop/start critical timings around the idle=poll idle loop
Linus Torvalds [Fri, 23 Oct 2015 13:10:51 +0000 (22:10 +0900)]
Merge branch 'akpm' (patches from Andrew)
Merge fixes from Andrew Morton:
"9 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
ocfs2/dlm: unlock lockres spinlock before dlm_lockres_put
fault-inject: fix inverted interval/probability values in printk
lib/Kconfig.debug: disable -Wframe-larger-than warnings with KASAN=y
mm: make sendfile(2) killable
thp: use is_zero_pfn() only after pte_present() check
mailmap: update Javier Martinez Canillas' email
MAINTAINERS: add Sergey as zsmalloc reviewer
mm: cma: fix incorrect type conversion for size during dma allocation
kmod: don't run async usermode helper as a child of kworker thread
Peter Zijlstra [Fri, 23 Oct 2015 09:50:08 +0000 (11:50 +0200)]
sched/core: Add missing lockdep_unpin() annotations
Luca and Wanpeng reported two missing annotations that led to
false lockdep complaints. Add the missing annotations.
Reported-by: Luca Abeni <luca.abeni@unitn.it>
Reported-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: cbce1a686700 ("sched,lockdep: Employ lock pinning")
Link: http://lkml.kernel.org/r/20151023095008.GY17308@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Fri, 23 Oct 2015 09:49:51 +0000 (18:49 +0900)]
Merge tag 'powerpc-4.3-5' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Revert "Use the POWER8 Micro Partition Prefetch Engine in KVM HV on
POWER8" from Paul
- Handle irq_happened flag correctly in off-line loop from Paul
- Validate rtas.entry before calling enter_rtas() from Vasant
* tag 'powerpc-4.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/rtas: Validate rtas.entry before calling enter_rtas()
powerpc/powernv: Handle irq_happened flag correctly in off-line loop
powerpc: Revert "Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8"
Linus Torvalds [Fri, 23 Oct 2015 09:38:00 +0000 (18:38 +0900)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes this time are for incorrect device nodes in
various ways, on on imx, berlin, exynos, ux500, uniphier, omap and
meson.
Chen-Yu Tsai now co-maintains mach-sunxi (Allwinner).
Other bug fixes include
- a partial revert of a broken tegra gpio patch
- irq affinity for arm ccn
- suspend on one Armada 385 machine
- enable ZONE_DMA to avoid an OMAP crash for over 2GB RAM
- turning on a regulator on beagleboard-x15 for HDMI
- making the omap gpmc debug code visible
- setup of orion network switch
- a rare build regression for pxa"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: OMAP2+: Fix imprecise external abort caused by bogus SRAM init
thermal: exynos: Fix register read in TMU
ARM: OMAP2+: Fix oops with LPAE and more than 2GB of memory
ARM: tegra: Comment out gpio-ranges properties
ARM: dts: uniphier: fix IRQ number for devices on PH1-LD6b ref board
drivers/perf: arm_pmu: avoid CPU device_node reference leak
bus: arm-ccn: Fix irq affinity setting on CPU migration
bus: arm-ccn: Handle correctly no-more-cpus case
ARM: mvebu: correct a385-db-ap compatible string
ARM: meson6: DTS: Fix wrong reg mapping and IRQ numbers
MAINTAINERS: Update Allwinner entry and add new maintainer
ARM: ux500: modify initial levelshifter status
ARM: pxa: fix pxa3xx DFI lockup hack
Documentation: ARM: List new omap MMC requirements
memory: omap-gpmc: dump "before" state before first modification
memory: omap-gpmc: Fix unselectable debug option for GPMC
ARM: dts: am57xx-beagle-x15: set VDD_SD to always-on
ARM: dts: Fix audio card detection on Peach boards
ARM: EXYNOS: Fix double of_node_put() when parsing child power domains
ARM: orion: Fix DSA platform device after mvmdio conversion
...
Linus Torvalds [Fri, 23 Oct 2015 09:32:29 +0000 (18:32 +0900)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM bugfixes from Paolo Bonzini:
"Bug fixes for ARM, mostly 4.3 regressions related to virtual interrupt
controller changes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm/arm64: KVM: Fix disabled distributor operation
arm/arm64: KVM: Clear map->active on pend/active clear
arm/arm64: KVM: Fix arch timer behavior for disabled interrupts
KVM: arm: use GIC support unconditionally
KVM: arm/arm64: Fix memory leak if timer initialization fails
KVM: arm/arm64: Do not inject spurious interrupts
Linus Torvalds [Fri, 23 Oct 2015 09:24:33 +0000 (18:24 +0900)]
Merge tag 'trace-fixes-v4.3-rc6' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Running tests on other changes, the system locked up due to lots of
warnings. It was caused by the stack tracer triggering a warning
about using rcu_dereference() when RCU was not watching. This can
happen due to the fact that the stack tracer uses the function tracer
to check each function, and there are functions that may be called and
traced when RCU stopped watching. Namely when a function is called
just before going idle or to userspace and after RCU stopped watching
that current CPU.
The first patch makes sure that RCU is watching when the stack tracer
uses RCU. The second patch is to make sure that the stack tracer does
not get called by functions in NMI, as it's not NMI safe"
* tag 'trace-fixes-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not allow stack_tracer to record stack in NMI
tracing: Have stack tracer force RCU to be watching
Linus Torvalds [Fri, 23 Oct 2015 09:21:55 +0000 (18:21 +0900)]
Merge tag 'sound-4.3-rc7' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There is nothing to worry you much, only a few small & stable patches
are found for usual stuff, HD-audio (a Lenovo laptop quirk, a fix for
minor error handling) and ASoC (trivial fixes for RT298 and WM
codecs).
The only remaining major change is the fix for ASoC SX_TLV control
that was overseen during refactoring, but the fix itself is trivial
and safe"
* tag 'sound-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8962: mark cache_dirty flag after software reset in pm_resume
ASoC: rt298: fix wrong setting of gpio2_en
ASoC: wm8904: Correct number of EQ registers
ALSA: hda - Fix deadlock at error in building PCM
ASoC: Add info callback for SX_TLV controls
ASoC: rt298: correct index default value
ALSA: hda - Fix inverted internal mic on Lenovo G50-80
ALSA: hdac: Explicitly add io.h
Linus Torvalds [Fri, 23 Oct 2015 09:15:20 +0000 (18:15 +0900)]
Merge tag 'media/v4.3-4' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some regression fixes and potential security issues:
- netup_unidvb: fix potential crash when spi is NULL
- rtl28xxu: fix control message flaws
- m88ds3103: fix a regression on Kernel 4.2
- c8sectpfe: fix some issues on this new driver
- v4l2-flash-led-class: fix a Kbuild dependency
- si2157 and si2158: check for array boundary when uploading firmware
files
- horus3a and lnbh25: fix some building troubles when some options
aren't selected
- ir-hix5hd2: drop the use of IRQF_NO_SUSPEND"
* tag 'media/v4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] m88ds3103: use own reg update_bits() implementation
[media] rtl28xxu: fix control message flaws
[media] v4l2-flash-led-class: Add missing VIDEO_V4L2 Kconfig dependency
[media] netup_unidvb: fix potential crash when spi is NULL
[media] si2168: Bounds check firmware
[media] si2157: Bounds check firmware
[media] ir-hix5hd2: drop the use of IRQF_NO_SUSPEND
[media] c8sectpfe: fix return of garbage
[media] c8sectpfe: fix ininitialized error return on firmware load failure
[media] lnbh25: Fix lnbh25_attach() function return type
[media] horus3a: Fix horus3a_attach() function parameters
Linus Torvalds [Fri, 23 Oct 2015 09:08:22 +0000 (18:08 +0900)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I've been a bit slow gathering these:
- drm/mst: one mutex leak in a fail path
- radeon: two oops fixes, one dpm fix
- i915: one messy set of fixes, where we revert the original fix, and
pull back the proper set of fixes from -next on top.
- nouveau: one fix for an illegal buffer placement.
Doesn't look too bad, hopefully shouldn't be too much more"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/gem: return only valid domain when there's only one
drm: fix mutex leak in drm_dp_get_mst_branch_device
drm/amdgpu: add missing dpm check for KV dpm late init
drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
drm/radeon/dpm: don't add pwm attributes if DPM is disabled
drm/i915: Add primary plane to mask if it's visible
drm/i915: Move sprite/cursor plane disable to intel_sanitize_crtc()
drm/i915: Assign hwmode after encoder state readout
Revert "drm/i915: Add primary plane to mask if it's visible"
drm/i915: Deny wrapping an userptr into a framebuffer
drm/i915: Enable DPLL VGA mode before P1/P2 divider write
drm/i915: Restore lost DPLL register write on gen2-4
drm/i915: Flush pipecontrol post-sync writes
drm/i915: Fix kerneldoc for i915_gem_shrink_all
Joseph Qi [Thu, 22 Oct 2015 20:32:29 +0000 (13:32 -0700)]
ocfs2/dlm: unlock lockres spinlock before dlm_lockres_put
dlm_lockres_put will call dlm_lockres_release if it is the last
reference, and then it may call dlm_print_one_lock_resource and
take lockres spinlock.
So unlock lockres spinlock before dlm_lockres_put to avoid deadlock.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Westphal [Thu, 22 Oct 2015 20:32:27 +0000 (13:32 -0700)]
fault-inject: fix inverted interval/probability values in printk
interval displays the probability and vice versa.
Fixes: 6adc4a22f20bb ("fault-inject: add ratelimit option")
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Thu, 22 Oct 2015 20:32:24 +0000 (13:32 -0700)]
lib/Kconfig.debug: disable -Wframe-larger-than warnings with KASAN=y
When the kernel compiled with KASAN=y, GCC adds redzones for each
variable on stack. This enlarges function's stack frame and causes:
'warning: the frame size of X bytes is larger than Y bytes'
The worst case I've seen for now is following:
../net/wireless/nl80211.c: In function `nl80211_send_wiphy':
../net/wireless/nl80211.c:1731:1: warning: the frame size of 5448 bytes is larger than 2048 bytes [-Wframe-larger-than=]
That kind of warning becomes useless with KASAN=y. It doesn't
necessarily indicate that there is some problem in the code, thus we
should turn it off.
(The KASAN=y stack size in increased from 16k to 32k for this reason)
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Thu, 22 Oct 2015 20:32:21 +0000 (13:32 -0700)]
mm: make sendfile(2) killable
Currently a simple program below issues a sendfile(2) system call which
takes about 62 days to complete in my test KVM instance.
int fd;
off_t off = 0;
fd = open("file", O_RDWR | O_TRUNC | O_SYNC | O_CREAT, 0644);
ftruncate(fd, 2);
lseek(fd, 0, SEEK_END);
sendfile(fd, fd, &off, 0xfffffff);
Now you should not ask kernel to do a stupid stuff like copying 256MB in
2-byte chunks and call fsync(2) after each chunk but if you do, sysadmin
should have a way to stop you.
We actually do have a check for fatal_signal_pending() in
generic_perform_write() which triggers in this path however because we
always succeed in writing something before the check is done, we return
value > 0 from generic_perform_write() and thus the information about
signal gets lost.
Fix the problem by doing the signal check before writing anything. That
way generic_perform_write() returns -EINTR, the error gets propagated up
and the sendfile loop terminates early.
Signed-off-by: Jan Kara <jack@suse.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Thu, 22 Oct 2015 20:32:19 +0000 (13:32 -0700)]
thp: use is_zero_pfn() only after pte_present() check
Use is_zero_pfn() on pteval only after pte_present() check on pteval
(It might be better idea to introduce is_zero_pte() which checks
pte_present() first).
Otherwise when working on a swap or migration entry and if pte_pfn's
result is equal to zero_pfn by chance, we lose user's data in
__collapse_huge_page_copy(). So if you're unlucky, the application
segfaults and finally you could see below message on exit:
BUG: Bad rss-counter state mm:
ffff88007f099300 idx:2 val:3
Fixes: ca0984caa823 ("mm: incorporate zero pages into transparent huge pages")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Javier Martinez Canillas [Thu, 22 Oct 2015 20:32:16 +0000 (13:32 -0700)]
mailmap: update Javier Martinez Canillas' email
The get_maintainer script still reports my old Collabora email based on
old commits but that address no longer exist so update mailmap to report
my current email and avoid people sending to the old address.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergey Senozhatsky [Thu, 22 Oct 2015 20:32:13 +0000 (13:32 -0700)]
MAINTAINERS: add Sergey as zsmalloc reviewer
Nominate myself as a zsmalloc reviewer.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rohit Vaswani [Thu, 22 Oct 2015 20:32:11 +0000 (13:32 -0700)]
mm: cma: fix incorrect type conversion for size during dma allocation
This was found during userspace fuzzing test when a large size dma cma
allocation is made by driver(like ion) through userspace.
show_stack+0x10/0x1c
dump_stack+0x74/0xc8
kasan_report_error+0x2b0/0x408
kasan_report+0x34/0x40
__asan_storeN+0x15c/0x168
memset+0x20/0x44
__dma_alloc_coherent+0x114/0x18c
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Thu, 22 Oct 2015 20:32:08 +0000 (13:32 -0700)]
kmod: don't run async usermode helper as a child of kworker thread
call_usermodehelper_exec_sync() does fork() + wait() with "unignored"
SIGCHLD. What we have missed is that this worker thread can have other
children previously forked by call_usermodehelper_exec_work() without
UMH_WAIT_PROC. If such a child exits in between it becomes a zombie
because auto-reaping only works if SIGCHLD is ignored, and nobody can
reap it (unless/until this worker thread exits too).
Change the !UMH_WAIT_PROC case to use CLONE_PARENT.
Note: this is only first step. All PF_KTHREAD tasks, even created by
kernel_thread() should have ->parent == kthreadd by default.
Fixes: bb304a5c6fc63d8506c ("kmod: handle UMH_WAIT_PROC from system unbound workqueue")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Fri, 23 Oct 2015 04:57:50 +0000 (06:57 +0200)]
Merge branch 'topic/hw-constraint-single' into for-next
Takashi Iwai [Fri, 23 Oct 2015 04:56:56 +0000 (06:56 +0200)]
Merge tag 'asoc-fix-v4.3-rc6' of git://git./linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.3
A bunch of driver fixes plus one core fix which fixes problems with
misreporting values from _SX controls following a recent refactoring.
This had gone unnoticed as such controls are quite rare.
Lars-Peter Clausen [Thu, 22 Oct 2015 08:43:23 +0000 (10:43 +0200)]
ASoC: fsl_sai: Constify rate constraints
The rate constraints in this driver are shared between all device
instances. It should not be (and is not) modified at runtime, so make them
const.
While we are at it also change the type of the rates array from u32 to
unsigned int. While both resolve to the same type, u32 is usually used to
empathize that the value is for a 32-bit hardware register or similar which
makes it slightly confusing in this context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lars-Peter Clausen [Thu, 22 Oct 2015 08:43:22 +0000 (10:43 +0200)]
ASoC: rx1950_uda1380: Constify rate constraints
The rate constraints in this board driver are not modified at runtime, so
make them const.
While we are at it also remove the unnecessary 0 initializer for the mask
field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This page took 0.048791 seconds and 5 git commands to generate.