projects / deliverable / linux.git / blob
? search:


18c30ca
[deliverable/linux.git] /
1 /*
2 * Driver for OMAP-UART controller.
3 * Based on drivers/serial/8250.c
4 *
5 * Copyright (C) 2010 Texas Instruments.
6 *
7 * Authors:
8 * Govindraj R <govindraj.raja@ti.com>
9 * Thara Gopinath <thara@ti.com>
10 *
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
15 *
16 * Note: This driver is made separate from 8250 driver as we cannot
17 * over load 8250 driver with omap platform specific configuration for
18 * features like DMA, it makes easier to implement features like DMA and
19 * hardware flow control and software flow control configuration with
20 * this driver as required for the omap-platform.
21 */
22
23 #if defined(CONFIG_SERIAL_OMAP_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
24 #define SUPPORT_SYSRQ
25 #endif
26
27 #include <linux/module.h>
28 #include <linux/init.h>
29 #include <linux/console.h>
30 #include <linux/serial_reg.h>
31 #include <linux/delay.h>
32 #include <linux/slab.h>
33 #include <linux/tty.h>
34 #include <linux/tty_flip.h>
35 #include <linux/platform_device.h>
36 #include <linux/io.h>
37 #include <linux/clk.h>
38 #include <linux/serial_core.h>
39 #include <linux/irq.h>
40 #include <linux/pm_runtime.h>
41 #include <linux/of.h>
42 #include <linux/of_irq.h>
43 #include <linux/gpio.h>
44 #include <linux/of_gpio.h>
45 #include <linux/platform_data/serial-omap.h>
46
47 #include <dt-bindings/gpio/gpio.h>
48
49 #define OMAP_MAX_HSUART_PORTS 6
50
51 #define UART_BUILD_REVISION(x, y) (((x) << 8) | (y))
52
53 #define OMAP_UART_REV_42 0x0402
54 #define OMAP_UART_REV_46 0x0406
55 #define OMAP_UART_REV_52 0x0502
56 #define OMAP_UART_REV_63 0x0603
57
58 #define OMAP_UART_TX_WAKEUP_EN BIT(7)
59
60 /* Feature flags */
61 #define OMAP_UART_WER_HAS_TX_WAKEUP BIT(0)
62
63 #define UART_ERRATA_i202_MDR1_ACCESS BIT(0)
64 #define UART_ERRATA_i291_DMA_FORCEIDLE BIT(1)
65
66 #define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
67
68 /* SCR register bitmasks */
69 #define OMAP_UART_SCR_RX_TRIG_GRANU1_MASK (1 << 7)
70 #define OMAP_UART_SCR_TX_TRIG_GRANU1_MASK (1 << 6)
71 #define OMAP_UART_SCR_TX_EMPTY (1 << 3)
72
73 /* FCR register bitmasks */
74 #define OMAP_UART_FCR_RX_FIFO_TRIG_MASK (0x3 << 6)
75 #define OMAP_UART_FCR_TX_FIFO_TRIG_MASK (0x3 << 4)
76
77 /* MVR register bitmasks */
78 #define OMAP_UART_MVR_SCHEME_SHIFT 30
79
80 #define OMAP_UART_LEGACY_MVR_MAJ_MASK 0xf0
81 #define OMAP_UART_LEGACY_MVR_MAJ_SHIFT 4
82 #define OMAP_UART_LEGACY_MVR_MIN_MASK 0x0f
83
84 #define OMAP_UART_MVR_MAJ_MASK 0x700
85 #define OMAP_UART_MVR_MAJ_SHIFT 8
86 #define OMAP_UART_MVR_MIN_MASK 0x3f
87
88 #define OMAP_UART_DMA_CH_FREE -1
89
90 #define MSR_SAVE_FLAGS UART_MSR_ANY_DELTA
91 #define OMAP_MODE13X_SPEED 230400
92
93 /* WER = 0x7F
94 * Enable module level wakeup in WER reg
95 */
96 #define OMAP_UART_WER_MOD_WKUP 0X7F
97
98 /* Enable XON/XOFF flow control on output */
99 #define OMAP_UART_SW_TX 0x08
100
101 /* Enable XON/XOFF flow control on input */
102 #define OMAP_UART_SW_RX 0x02
103
104 #define OMAP_UART_SW_CLR 0xF0
105
106 #define OMAP_UART_TCR_TRIG 0x0F
107
108 struct uart_omap_dma {
109 u8 uart_dma_tx;
110 u8 uart_dma_rx;
111 int rx_dma_channel;
112 int tx_dma_channel;
113 dma_addr_t rx_buf_dma_phys;
114 dma_addr_t tx_buf_dma_phys;
115 unsigned int uart_base;
116 /*
117 * Buffer for rx dma.It is not required for tx because the buffer
118 * comes from port structure.
119 */
120 unsigned char *rx_buf;
121 unsigned int prev_rx_dma_pos;
122 int tx_buf_size;
123 int tx_dma_used;
124 int rx_dma_used;
125 spinlock_t tx_lock;
126 spinlock_t rx_lock;
127 /* timer to poll activity on rx dma */
128 struct timer_list rx_timer;
129 unsigned int rx_buf_size;
130 unsigned int rx_poll_rate;
131 unsigned int rx_timeout;
132 };
133
134 struct uart_omap_port {
135 struct uart_port port;
136 struct uart_omap_dma uart_dma;
137 struct device *dev;
138 int wakeirq;
139
140 unsigned char ier;
141 unsigned char lcr;
142 unsigned char mcr;
143 unsigned char fcr;
144 unsigned char efr;
145 unsigned char dll;
146 unsigned char dlh;
147 unsigned char mdr1;
148 unsigned char scr;
149 unsigned char wer;
150
151 int use_dma;
152 /*
153 * Some bits in registers are cleared on a read, so they must
154 * be saved whenever the register is read but the bits will not
155 * be immediately processed.
156 */
157 unsigned int lsr_break_flag;
158 unsigned char msr_saved_flags;
159 char name[20];
160 unsigned long port_activity;
161 int context_loss_cnt;
162 u32 errata;
163 u8 wakeups_enabled;
164 u32 features;
165
166 struct serial_rs485 rs485;
167 int rts_gpio;
168
169 struct pm_qos_request pm_qos_request;
170 u32 latency;
171 u32 calc_latency;
172 struct work_struct qos_work;
173 bool is_suspending;
174 };
175
176 #define to_uart_omap_port(p) ((container_of((p), struct uart_omap_port, port)))
177
178 static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
179
180 /* Forward declaration of functions */
181 static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1);
182
183 static inline unsigned int serial_in(struct uart_omap_port *up, int offset)
184 {
185 offset <<= up->port.regshift;
186 return readw(up->port.membase + offset);
187 }
188
189 static inline void serial_out(struct uart_omap_port *up, int offset, int value)
190 {
191 offset <<= up->port.regshift;
192 writew(value, up->port.membase + offset);
193 }
194
195 static inline void serial_omap_clear_fifos(struct uart_omap_port *up)
196 {
197 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
198 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
199 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
200 serial_out(up, UART_FCR, 0);
201 }
202
203 static int serial_omap_get_context_loss_count(struct uart_omap_port *up)
204 {
205 struct omap_uart_port_info *pdata = dev_get_platdata(up->dev);
206
207 if (!pdata || !pdata->get_context_loss_count)
208 return -EINVAL;
209
210 return pdata->get_context_loss_count(up->dev);
211 }
212
213 static inline void serial_omap_enable_wakeirq(struct uart_omap_port *up,
214 bool enable)
215 {
216 if (!up->wakeirq)
217 return;
218
219 if (enable)
220 enable_irq(up->wakeirq);
221 else
222 disable_irq_nosync(up->wakeirq);
223 }
224
225 static void serial_omap_enable_wakeup(struct uart_omap_port *up, bool enable)
226 {
227 struct omap_uart_port_info *pdata = dev_get_platdata(up->dev);
228
229 if (enable == up->wakeups_enabled)
230 return;
231
232 serial_omap_enable_wakeirq(up, enable);
233 up->wakeups_enabled = enable;
234
235 if (!pdata || !pdata->enable_wakeup)
236 return;
237
238 pdata->enable_wakeup(up->dev, enable);
239 }
240
241 /*
242 * Calculate the absolute difference between the desired and actual baud
243 * rate for the given mode.
244 */
245 static inline int calculate_baud_abs_diff(struct uart_port *port,
246 unsigned int baud, unsigned int mode)
247 {
248 unsigned int n = port->uartclk / (mode * baud);
249 int abs_diff;
250
251 if (n == 0)
252 n = 1;
253
254 abs_diff = baud - (port->uartclk / (mode * n));
255 if (abs_diff < 0)
256 abs_diff = -abs_diff;
257
258 return abs_diff;
259 }
260
261 /*
262 * serial_omap_baud_is_mode16 - check if baud rate is MODE16X
263 * @port: uart port info
264 * @baud: baudrate for which mode needs to be determined
265 *
266 * Returns true if baud rate is MODE16X and false if MODE13X
267 * Original table in OMAP TRM named "UART Mode Baud Rates, Divisor Values,
268 * and Error Rates" determines modes not for all common baud rates.
269 * E.g. for 1000000 baud rate mode must be 16x, but according to that
270 * table it's determined as 13x.
271 */
272 static bool
273 serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud)
274 {
275 int abs_diff_13 = calculate_baud_abs_diff(port, baud, 13);
276 int abs_diff_16 = calculate_baud_abs_diff(port, baud, 16);
277
278 return (abs_diff_13 >= abs_diff_16);
279 }
280
281 /*
282 * serial_omap_get_divisor - calculate divisor value
283 * @port: uart port info
284 * @baud: baudrate for which divisor needs to be calculated.
285 */
286 static unsigned int
287 serial_omap_get_divisor(struct uart_port *port, unsigned int baud)
288 {
289 unsigned int mode;
290
291 if (!serial_omap_baud_is_mode16(port, baud))
292 mode = 13;
293 else
294 mode = 16;
295 return port->uartclk/(mode * baud);
296 }
297
298 static void serial_omap_enable_ms(struct uart_port *port)
299 {
300 struct uart_omap_port *up = to_uart_omap_port(port);
301
302 dev_dbg(up->port.dev, "serial_omap_enable_ms+%d\n", up->port.line);
303
304 pm_runtime_get_sync(up->dev);
305 up->ier |= UART_IER_MSI;
306 serial_out(up, UART_IER, up->ier);
307 pm_runtime_mark_last_busy(up->dev);
308 pm_runtime_put_autosuspend(up->dev);
309 }
310
311 static void serial_omap_stop_tx(struct uart_port *port)
312 {
313 struct uart_omap_port *up = to_uart_omap_port(port);
314 int res;
315
316 pm_runtime_get_sync(up->dev);
317
318 /* Handle RS-485 */
319 if (up->rs485.flags & SER_RS485_ENABLED) {
320 if (up->scr & OMAP_UART_SCR_TX_EMPTY) {
321 /* THR interrupt is fired when both TX FIFO and TX
322 * shift register are empty. This means there's nothing
323 * left to transmit now, so make sure the THR interrupt
324 * is fired when TX FIFO is below the trigger level,
325 * disable THR interrupts and toggle the RS-485 GPIO
326 * data direction pin if needed.
327 */
328 up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
329 serial_out(up, UART_OMAP_SCR, up->scr);
330 res = (up->rs485.flags & SER_RS485_RTS_AFTER_SEND) ? 1 : 0;
331 if (gpio_get_value(up->rts_gpio) != res) {
332 if (up->rs485.delay_rts_after_send > 0)
333 mdelay(up->rs485.delay_rts_after_send);
334 gpio_set_value(up->rts_gpio, res);
335 }
336 } else {
337 /* We're asked to stop, but there's still stuff in the
338 * UART FIFO, so make sure the THR interrupt is fired
339 * when both TX FIFO and TX shift register are empty.
340 * The next THR interrupt (if no transmission is started
341 * in the meantime) will indicate the end of a
342 * transmission. Therefore we _don't_ disable THR
343 * interrupts in this situation.
344 */
345 up->scr |= OMAP_UART_SCR_TX_EMPTY;
346 serial_out(up, UART_OMAP_SCR, up->scr);
347 return;
348 }
349 }
350
351 if (up->ier & UART_IER_THRI) {
352 up->ier &= ~UART_IER_THRI;
353 serial_out(up, UART_IER, up->ier);
354 }
355
356 if ((up->rs485.flags & SER_RS485_ENABLED) &&
357 !(up->rs485.flags & SER_RS485_RX_DURING_TX)) {
358 /*
359 * Empty the RX FIFO, we are not interested in anything
360 * received during the half-duplex transmission.
361 */
362 serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_RCVR);
363 /* Re-enable RX interrupts */
364 up->ier |= UART_IER_RLSI | UART_IER_RDI;
365 up->port.read_status_mask |= UART_LSR_DR;
366 serial_out(up, UART_IER, up->ier);
367 }
368
369 pm_runtime_mark_last_busy(up->dev);
370 pm_runtime_put_autosuspend(up->dev);
371 }
372
373 static void serial_omap_stop_rx(struct uart_port *port)
374 {
375 struct uart_omap_port *up = to_uart_omap_port(port);
376
377 pm_runtime_get_sync(up->dev);
378 up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
379 up->port.read_status_mask &= ~UART_LSR_DR;
380 serial_out(up, UART_IER, up->ier);
381 pm_runtime_mark_last_busy(up->dev);
382 pm_runtime_put_autosuspend(up->dev);
383 }
384
385 static void transmit_chars(struct uart_omap_port *up, unsigned int lsr)
386 {
387 struct circ_buf *xmit = &up->port.state->xmit;
388 int count;
389
390 if (up->port.x_char) {
391 serial_out(up, UART_TX, up->port.x_char);
392 up->port.icount.tx++;
393 up->port.x_char = 0;
394 return;
395 }
396 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
397 serial_omap_stop_tx(&up->port);
398 return;
399 }
400 count = up->port.fifosize / 4;
401 do {
402 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
403 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
404 up->port.icount.tx++;
405 if (uart_circ_empty(xmit))
406 break;
407 } while (--count > 0);
408
409 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
410 uart_write_wakeup(&up->port);
411
412 if (uart_circ_empty(xmit))
413 serial_omap_stop_tx(&up->port);
414 }
415
416 static inline void serial_omap_enable_ier_thri(struct uart_omap_port *up)
417 {
418 if (!(up->ier & UART_IER_THRI)) {
419 up->ier |= UART_IER_THRI;
420 serial_out(up, UART_IER, up->ier);
421 }
422 }
423
424 static void serial_omap_start_tx(struct uart_port *port)
425 {
426 struct uart_omap_port *up = to_uart_omap_port(port);
427 int res;
428
429 pm_runtime_get_sync(up->dev);
430
431 /* Handle RS-485 */
432 if (up->rs485.flags & SER_RS485_ENABLED) {
433 /* Fire THR interrupts when FIFO is below trigger level */
434 up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
435 serial_out(up, UART_OMAP_SCR, up->scr);
436
437 /* if rts not already enabled */
438 res = (up->rs485.flags & SER_RS485_RTS_ON_SEND) ? 1 : 0;
439 if (gpio_get_value(up->rts_gpio) != res) {
440 gpio_set_value(up->rts_gpio, res);
441 if (up->rs485.delay_rts_before_send > 0)
442 mdelay(up->rs485.delay_rts_before_send);
443 }
444 }
445
446 if ((up->rs485.flags & SER_RS485_ENABLED) &&
447 !(up->rs485.flags & SER_RS485_RX_DURING_TX))
448 serial_omap_stop_rx(port);
449
450 serial_omap_enable_ier_thri(up);
451 pm_runtime_mark_last_busy(up->dev);
452 pm_runtime_put_autosuspend(up->dev);
453 }
454
455 static void serial_omap_throttle(struct uart_port *port)
456 {
457 struct uart_omap_port *up = to_uart_omap_port(port);
458 unsigned long flags;
459
460 pm_runtime_get_sync(up->dev);
461 spin_lock_irqsave(&up->port.lock, flags);
462 up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
463 serial_out(up, UART_IER, up->ier);
464 spin_unlock_irqrestore(&up->port.lock, flags);
465 pm_runtime_mark_last_busy(up->dev);
466 pm_runtime_put_autosuspend(up->dev);
467 }
468
469 static void serial_omap_unthrottle(struct uart_port *port)
470 {
471 struct uart_omap_port *up = to_uart_omap_port(port);
472 unsigned long flags;
473
474 pm_runtime_get_sync(up->dev);
475 spin_lock_irqsave(&up->port.lock, flags);
476 up->ier |= UART_IER_RLSI | UART_IER_RDI;
477 serial_out(up, UART_IER, up->ier);
478 spin_unlock_irqrestore(&up->port.lock, flags);
479 pm_runtime_mark_last_busy(up->dev);
480 pm_runtime_put_autosuspend(up->dev);
481 }
482
483 static unsigned int check_modem_status(struct uart_omap_port *up)
484 {
485 unsigned int status;
486
487 status = serial_in(up, UART_MSR);
488 status |= up->msr_saved_flags;
489 up->msr_saved_flags = 0;
490 if ((status & UART_MSR_ANY_DELTA) == 0)
491 return status;
492
493 if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
494 up->port.state != NULL) {
495 if (status & UART_MSR_TERI)
496 up->port.icount.rng++;
497 if (status & UART_MSR_DDSR)
498 up->port.icount.dsr++;
499 if (status & UART_MSR_DDCD)
500 uart_handle_dcd_change
501 (&up->port, status & UART_MSR_DCD);
502 if (status & UART_MSR_DCTS)
503 uart_handle_cts_change
504 (&up->port, status & UART_MSR_CTS);
505 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
506 }
507
508 return status;
509 }
510
511 static void serial_omap_rlsi(struct uart_omap_port *up, unsigned int lsr)
512 {
513 unsigned int flag;
514 unsigned char ch = 0;
515
516 if (likely(lsr & UART_LSR_DR))
517 ch = serial_in(up, UART_RX);
518
519 up->port.icount.rx++;
520 flag = TTY_NORMAL;
521
522 if (lsr & UART_LSR_BI) {
523 flag = TTY_BREAK;
524 lsr &= ~(UART_LSR_FE | UART_LSR_PE);
525 up->port.icount.brk++;
526 /*
527 * We do the SysRQ and SAK checking
528 * here because otherwise the break
529 * may get masked by ignore_status_mask
530 * or read_status_mask.
531 */
532 if (uart_handle_break(&up->port))
533 return;
534
535 }
536
537 if (lsr & UART_LSR_PE) {
538 flag = TTY_PARITY;
539 up->port.icount.parity++;
540 }
541
542 if (lsr & UART_LSR_FE) {
543 flag = TTY_FRAME;
544 up->port.icount.frame++;
545 }
546
547 if (lsr & UART_LSR_OE)
548 up->port.icount.overrun++;
549
550 #ifdef CONFIG_SERIAL_OMAP_CONSOLE
551 if (up->port.line == up->port.cons->index) {
552 /* Recover the break flag from console xmit */
553 lsr |= up->lsr_break_flag;
554 }
555 #endif
556 uart_insert_char(&up->port, lsr, UART_LSR_OE, 0, flag);
557 }
558
559 static void serial_omap_rdi(struct uart_omap_port *up, unsigned int lsr)
560 {
561 unsigned char ch = 0;
562 unsigned int flag;
563
564 if (!(lsr & UART_LSR_DR))
565 return;
566
567 ch = serial_in(up, UART_RX);
568 flag = TTY_NORMAL;
569 up->port.icount.rx++;
570
571 if (uart_handle_sysrq_char(&up->port, ch))
572 return;
573
574 uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
575 }
576
577 /**
578 * serial_omap_irq() - This handles the interrupt from one port
579 * @irq: uart port irq number
580 * @dev_id: uart port info
581 */
582 static irqreturn_t serial_omap_irq(int irq, void *dev_id)
583 {
584 struct uart_omap_port *up = dev_id;
585 unsigned int iir, lsr;
586 unsigned int type;
587 irqreturn_t ret = IRQ_NONE;
588 int max_count = 256;
589
590 spin_lock(&up->port.lock);
591 pm_runtime_get_sync(up->dev);
592
593 do {
594 iir = serial_in(up, UART_IIR);
595 if (iir & UART_IIR_NO_INT)
596 break;
597
598 ret = IRQ_HANDLED;
599 lsr = serial_in(up, UART_LSR);
600
601 /* extract IRQ type from IIR register */
602 type = iir & 0x3e;
603
604 switch (type) {
605 case UART_IIR_MSI:
606 check_modem_status(up);
607 break;
608 case UART_IIR_THRI:
609 transmit_chars(up, lsr);
610 break;
611 case UART_IIR_RX_TIMEOUT:
612 /* FALLTHROUGH */
613 case UART_IIR_RDI:
614 serial_omap_rdi(up, lsr);
615 break;
616 case UART_IIR_RLSI:
617 serial_omap_rlsi(up, lsr);
618 break;
619 case UART_IIR_CTS_RTS_DSR:
620 /* simply try again */
621 break;
622 case UART_IIR_XOFF:
623 /* FALLTHROUGH */
624 default:
625 break;
626 }
627 } while (!(iir & UART_IIR_NO_INT) && max_count--);
628
629 spin_unlock(&up->port.lock);
630
631 tty_flip_buffer_push(&up->port.state->port);
632
633 pm_runtime_mark_last_busy(up->dev);
634 pm_runtime_put_autosuspend(up->dev);
635 up->port_activity = jiffies;
636
637 return ret;
638 }
639
640 static unsigned int serial_omap_tx_empty(struct uart_port *port)
641 {
642 struct uart_omap_port *up = to_uart_omap_port(port);
643 unsigned long flags = 0;
644 unsigned int ret = 0;
645
646 pm_runtime_get_sync(up->dev);
647 dev_dbg(up->port.dev, "serial_omap_tx_empty+%d\n", up->port.line);
648 spin_lock_irqsave(&up->port.lock, flags);
649 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
650 spin_unlock_irqrestore(&up->port.lock, flags);
651 pm_runtime_mark_last_busy(up->dev);
652 pm_runtime_put_autosuspend(up->dev);
653 return ret;
654 }
655
656 static unsigned int serial_omap_get_mctrl(struct uart_port *port)
657 {
658 struct uart_omap_port *up = to_uart_omap_port(port);
659 unsigned int status;
660 unsigned int ret = 0;
661
662 pm_runtime_get_sync(up->dev);
663 status = check_modem_status(up);
664 pm_runtime_mark_last_busy(up->dev);
665 pm_runtime_put_autosuspend(up->dev);
666
667 dev_dbg(up->port.dev, "serial_omap_get_mctrl+%d\n", up->port.line);
668
669 if (status & UART_MSR_DCD)
670 ret |= TIOCM_CAR;
671 if (status & UART_MSR_RI)
672 ret |= TIOCM_RNG;
673 if (status & UART_MSR_DSR)
674 ret |= TIOCM_DSR;
675 if (status & UART_MSR_CTS)
676 ret |= TIOCM_CTS;
677 return ret;
678 }
679
680 static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
681 {
682 struct uart_omap_port *up = to_uart_omap_port(port);
683 unsigned char mcr = 0, old_mcr;
684
685 dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->port.line);
686 if (mctrl & TIOCM_RTS)
687 mcr |= UART_MCR_RTS;
688 if (mctrl & TIOCM_DTR)
689 mcr |= UART_MCR_DTR;
690 if (mctrl & TIOCM_OUT1)
691 mcr |= UART_MCR_OUT1;
692 if (mctrl & TIOCM_OUT2)
693 mcr |= UART_MCR_OUT2;
694 if (mctrl & TIOCM_LOOP)
695 mcr |= UART_MCR_LOOP;
696
697 pm_runtime_get_sync(up->dev);
698 old_mcr = serial_in(up, UART_MCR);
699 old_mcr &= ~(UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_OUT1 |
700 UART_MCR_DTR | UART_MCR_RTS);
701 up->mcr = old_mcr | mcr;
702 serial_out(up, UART_MCR, up->mcr);
703 pm_runtime_mark_last_busy(up->dev);
704 pm_runtime_put_autosuspend(up->dev);
705 }
706
707 static void serial_omap_break_ctl(struct uart_port *port, int break_state)
708 {
709 struct uart_omap_port *up = to_uart_omap_port(port);
710 unsigned long flags = 0;
711
712 dev_dbg(up->port.dev, "serial_omap_break_ctl+%d\n", up->port.line);
713 pm_runtime_get_sync(up->dev);
714 spin_lock_irqsave(&up->port.lock, flags);
715 if (break_state == -1)
716 up->lcr |= UART_LCR_SBC;
717 else
718 up->lcr &= ~UART_LCR_SBC;
719 serial_out(up, UART_LCR, up->lcr);
720 spin_unlock_irqrestore(&up->port.lock, flags);
721 pm_runtime_mark_last_busy(up->dev);
722 pm_runtime_put_autosuspend(up->dev);
723 }
724
725 static int serial_omap_startup(struct uart_port *port)
726 {
727 struct uart_omap_port *up = to_uart_omap_port(port);
728 unsigned long flags = 0;
729 int retval;
730
731 /*
732 * Allocate the IRQ
733 */
734 retval = request_irq(up->port.irq, serial_omap_irq, up->port.irqflags,
735 up->name, up);
736 if (retval)
737 return retval;
738
739 /* Optional wake-up IRQ */
740 if (up->wakeirq) {
741 retval = request_irq(up->wakeirq, serial_omap_irq,
742 up->port.irqflags, up->name, up);
743 if (retval) {
744 free_irq(up->port.irq, up);
745 return retval;
746 }
747 disable_irq(up->wakeirq);
748 }
749
750 dev_dbg(up->port.dev, "serial_omap_startup+%d\n", up->port.line);
751
752 pm_runtime_get_sync(up->dev);
753 /*
754 * Clear the FIFO buffers and disable them.
755 * (they will be reenabled in set_termios())
756 */
757 serial_omap_clear_fifos(up);
758 /* For Hardware flow control */
759 serial_out(up, UART_MCR, UART_MCR_RTS);
760
761 /*
762 * Clear the interrupt registers.
763 */
764 (void) serial_in(up, UART_LSR);
765 if (serial_in(up, UART_LSR) & UART_LSR_DR)
766 (void) serial_in(up, UART_RX);
767 (void) serial_in(up, UART_IIR);
768 (void) serial_in(up, UART_MSR);
769
770 /*
771 * Now, initialize the UART
772 */
773 serial_out(up, UART_LCR, UART_LCR_WLEN8);
774 spin_lock_irqsave(&up->port.lock, flags);
775 /*
776 * Most PC uarts need OUT2 raised to enable interrupts.
777 */
778 up->port.mctrl |= TIOCM_OUT2;
779 serial_omap_set_mctrl(&up->port, up->port.mctrl);
780 spin_unlock_irqrestore(&up->port.lock, flags);
781
782 up->msr_saved_flags = 0;
783 /*
784 * Finally, enable interrupts. Note: Modem status interrupts
785 * are set via set_termios(), which will be occurring imminently
786 * anyway, so we don't enable them here.
787 */
788 up->ier = UART_IER_RLSI | UART_IER_RDI;
789 serial_out(up, UART_IER, up->ier);
790
791 /* Enable module level wake up */
792 up->wer = OMAP_UART_WER_MOD_WKUP;
793 if (up->features & OMAP_UART_WER_HAS_TX_WAKEUP)
794 up->wer |= OMAP_UART_TX_WAKEUP_EN;
795
796 serial_out(up, UART_OMAP_WER, up->wer);
797
798 pm_runtime_mark_last_busy(up->dev);
799 pm_runtime_put_autosuspend(up->dev);
800 up->port_activity = jiffies;
801 return 0;
802 }
803
804 static void serial_omap_shutdown(struct uart_port *port)
805 {
806 struct uart_omap_port *up = to_uart_omap_port(port);
807 unsigned long flags = 0;
808
809 dev_dbg(up->port.dev, "serial_omap_shutdown+%d\n", up->port.line);
810
811 pm_runtime_get_sync(up->dev);
812 /*
813 * Disable interrupts from this port
814 */
815 up->ier = 0;
816 serial_out(up, UART_IER, 0);
817
818 spin_lock_irqsave(&up->port.lock, flags);
819 up->port.mctrl &= ~TIOCM_OUT2;
820 serial_omap_set_mctrl(&up->port, up->port.mctrl);
821 spin_unlock_irqrestore(&up->port.lock, flags);
822
823 /*
824 * Disable break condition and FIFOs
825 */
826 serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
827 serial_omap_clear_fifos(up);
828
829 /*
830 * Read data port to reset things, and then free the irq
831 */
832 if (serial_in(up, UART_LSR) & UART_LSR_DR)
833 (void) serial_in(up, UART_RX);
834
835 pm_runtime_mark_last_busy(up->dev);
836 pm_runtime_put_autosuspend(up->dev);
837 free_irq(up->port.irq, up);
838 if (up->wakeirq)
839 free_irq(up->wakeirq, up);
840 }
841
842 static void serial_omap_uart_qos_work(struct work_struct *work)
843 {
844 struct uart_omap_port *up = container_of(work, struct uart_omap_port,
845 qos_work);
846
847 pm_qos_update_request(&up->pm_qos_request, up->latency);
848 }
849
850 static void
851 serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
852 struct ktermios *old)
853 {
854 struct uart_omap_port *up = to_uart_omap_port(port);
855 unsigned char cval = 0;
856 unsigned long flags = 0;
857 unsigned int baud, quot;
858
859 switch (termios->c_cflag & CSIZE) {
860 case CS5:
861 cval = UART_LCR_WLEN5;
862 break;
863 case CS6:
864 cval = UART_LCR_WLEN6;
865 break;
866 case CS7:
867 cval = UART_LCR_WLEN7;
868 break;
869 default:
870 case CS8:
871 cval = UART_LCR_WLEN8;
872 break;
873 }
874
875 if (termios->c_cflag & CSTOPB)
876 cval |= UART_LCR_STOP;
877 if (termios->c_cflag & PARENB)
878 cval |= UART_LCR_PARITY;
879 if (!(termios->c_cflag & PARODD))
880 cval |= UART_LCR_EPAR;
881 if (termios->c_cflag & CMSPAR)
882 cval |= UART_LCR_SPAR;
883
884 /*
885 * Ask the core to calculate the divisor for us.
886 */
887
888 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
889 quot = serial_omap_get_divisor(port, baud);
890
891 /* calculate wakeup latency constraint */
892 up->calc_latency = (USEC_PER_SEC * up->port.fifosize) / (baud / 8);
893 up->latency = up->calc_latency;
894 schedule_work(&up->qos_work);
895
896 up->dll = quot & 0xff;
897 up->dlh = quot >> 8;
898 up->mdr1 = UART_OMAP_MDR1_DISABLE;
899
900 up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
901 UART_FCR_ENABLE_FIFO;
902
903 /*
904 * Ok, we're now changing the port state. Do it with
905 * interrupts disabled.
906 */
907 pm_runtime_get_sync(up->dev);
908 spin_lock_irqsave(&up->port.lock, flags);
909
910 /*
911 * Update the per-port timeout.
912 */
913 uart_update_timeout(port, termios->c_cflag, baud);
914
915 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
916 if (termios->c_iflag & INPCK)
917 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
918 if (termios->c_iflag & (BRKINT | PARMRK))
919 up->port.read_status_mask |= UART_LSR_BI;
920
921 /*
922 * Characters to ignore
923 */
924 up->port.ignore_status_mask = 0;
925 if (termios->c_iflag & IGNPAR)
926 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
927 if (termios->c_iflag & IGNBRK) {
928 up->port.ignore_status_mask |= UART_LSR_BI;
929 /*
930 * If we're ignoring parity and break indicators,
931 * ignore overruns too (for real raw support).
932 */
933 if (termios->c_iflag & IGNPAR)
934 up->port.ignore_status_mask |= UART_LSR_OE;
935 }
936
937 /*
938 * ignore all characters if CREAD is not set
939 */
940 if ((termios->c_cflag & CREAD) == 0)
941 up->port.ignore_status_mask |= UART_LSR_DR;
942
943 /*
944 * Modem status interrupts
945 */
946 up->ier &= ~UART_IER_MSI;
947 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
948 up->ier |= UART_IER_MSI;
949 serial_out(up, UART_IER, up->ier);
950 serial_out(up, UART_LCR, cval); /* reset DLAB */
951 up->lcr = cval;
952 up->scr = 0;
953
954 /* FIFOs and DMA Settings */
955
956 /* FCR can be changed only when the
957 * baud clock is not running
958 * DLL_REG and DLH_REG set to 0.
959 */
960 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
961 serial_out(up, UART_DLL, 0);
962 serial_out(up, UART_DLM, 0);
963 serial_out(up, UART_LCR, 0);
964
965 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
966
967 up->efr = serial_in(up, UART_EFR) & ~UART_EFR_ECB;
968 up->efr &= ~UART_EFR_SCD;
969 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
970
971 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
972 up->mcr = serial_in(up, UART_MCR) & ~UART_MCR_TCRTLR;
973 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
974 /* FIFO ENABLE, DMA MODE */
975
976 up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
977 /*
978 * NOTE: Setting OMAP_UART_SCR_RX_TRIG_GRANU1_MASK
979 * sets Enables the granularity of 1 for TRIGGER RX
980 * level. Along with setting RX FIFO trigger level
981 * to 1 (as noted below, 16 characters) and TLR[3:0]
982 * to zero this will result RX FIFO threshold level
983 * to 1 character, instead of 16 as noted in comment
984 * below.
985 */
986
987 /* Set receive FIFO threshold to 16 characters and
988 * transmit FIFO threshold to 32 spaces
989 */
990 up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK;
991 up->fcr &= ~OMAP_UART_FCR_TX_FIFO_TRIG_MASK;
992 up->fcr |= UART_FCR6_R_TRIGGER_16 | UART_FCR6_T_TRIGGER_24 |
993 UART_FCR_ENABLE_FIFO;
994
995 serial_out(up, UART_FCR, up->fcr);
996 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
997
998 serial_out(up, UART_OMAP_SCR, up->scr);
999
1000 /* Reset UART_MCR_TCRTLR: this must be done with the EFR_ECB bit set */
1001 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
1002 serial_out(up, UART_MCR, up->mcr);
1003 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1004 serial_out(up, UART_EFR, up->efr);
1005 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
1006
1007 /* Protocol, Baud Rate, and Interrupt Settings */
1008
1009 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1010 serial_omap_mdr1_errataset(up, up->mdr1);
1011 else
1012 serial_out(up, UART_OMAP_MDR1, up->mdr1);
1013
1014 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1015 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
1016
1017 serial_out(up, UART_LCR, 0);
1018 serial_out(up, UART_IER, 0);
1019 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1020
1021 serial_out(up, UART_DLL, up->dll); /* LS of divisor */
1022 serial_out(up, UART_DLM, up->dlh); /* MS of divisor */
1023
1024 serial_out(up, UART_LCR, 0);
1025 serial_out(up, UART_IER, up->ier);
1026 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1027
1028 serial_out(up, UART_EFR, up->efr);
1029 serial_out(up, UART_LCR, cval);
1030
1031 if (!serial_omap_baud_is_mode16(port, baud))
1032 up->mdr1 = UART_OMAP_MDR1_13X_MODE;
1033 else
1034 up->mdr1 = UART_OMAP_MDR1_16X_MODE;
1035
1036 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1037 serial_omap_mdr1_errataset(up, up->mdr1);
1038 else
1039 serial_out(up, UART_OMAP_MDR1, up->mdr1);
1040
1041 /* Configure flow control */
1042 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1043
1044 /* XON1/XOFF1 accessible mode B, TCRTLR=0, ECB=0 */
1045 serial_out(up, UART_XON1, termios->c_cc[VSTART]);
1046 serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]);
1047
1048 /* Enable access to TCR/TLR */
1049 serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
1050 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
1051 serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
1052
1053 serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
1054
1055 if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
1056 /* Enable AUTORTS and AUTOCTS */
1057 up->efr |= UART_EFR_CTS | UART_EFR_RTS;
1058
1059 /* Ensure MCR RTS is asserted */
1060 up->mcr |= UART_MCR_RTS;
1061 } else {
1062 /* Disable AUTORTS and AUTOCTS */
1063 up->efr &= ~(UART_EFR_CTS | UART_EFR_RTS);
1064 }
1065
1066 if (up->port.flags & UPF_SOFT_FLOW) {
1067 /* clear SW control mode bits */
1068 up->efr &= OMAP_UART_SW_CLR;
1069
1070 /*
1071 * IXON Flag:
1072 * Enable XON/XOFF flow control on input.
1073 * Receiver compares XON1, XOFF1.
1074 */
1075 if (termios->c_iflag & IXON)
1076 up->efr |= OMAP_UART_SW_RX;
1077
1078 /*
1079 * IXOFF Flag:
1080 * Enable XON/XOFF flow control on output.
1081 * Transmit XON1, XOFF1
1082 */
1083 if (termios->c_iflag & IXOFF)
1084 up->efr |= OMAP_UART_SW_TX;
1085
1086 /*
1087 * IXANY Flag:
1088 * Enable any character to restart output.
1089 * Operation resumes after receiving any
1090 * character after recognition of the XOFF character
1091 */
1092 if (termios->c_iflag & IXANY)
1093 up->mcr |= UART_MCR_XONANY;
1094 else
1095 up->mcr &= ~UART_MCR_XONANY;
1096 }
1097 serial_out(up, UART_MCR, up->mcr);
1098 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1099 serial_out(up, UART_EFR, up->efr);
1100 serial_out(up, UART_LCR, up->lcr);
1101
1102 serial_omap_set_mctrl(&up->port, up->port.mctrl);
1103
1104 spin_unlock_irqrestore(&up->port.lock, flags);
1105 pm_runtime_mark_last_busy(up->dev);
1106 pm_runtime_put_autosuspend(up->dev);
1107 dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->port.line);
1108 }
1109
1110 static void
1111 serial_omap_pm(struct uart_port *port, unsigned int state,
1112 unsigned int oldstate)
1113 {
1114 struct uart_omap_port *up = to_uart_omap_port(port);
1115 unsigned char efr;
1116
1117 dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->port.line);
1118
1119 pm_runtime_get_sync(up->dev);
1120 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1121 efr = serial_in(up, UART_EFR);
1122 serial_out(up, UART_EFR, efr | UART_EFR_ECB);
1123 serial_out(up, UART_LCR, 0);
1124
1125 serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
1126 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
1127 serial_out(up, UART_EFR, efr);
1128 serial_out(up, UART_LCR, 0);
1129
1130 if (!device_may_wakeup(up->dev)) {
1131 if (!state)
1132 pm_runtime_forbid(up->dev);
1133 else
1134 pm_runtime_allow(up->dev);
1135 }
1136
1137 pm_runtime_mark_last_busy(up->dev);
1138 pm_runtime_put_autosuspend(up->dev);
1139 }
1140
1141 static void serial_omap_release_port(struct uart_port *port)
1142 {
1143 dev_dbg(port->dev, "serial_omap_release_port+\n");
1144 }
1145
1146 static int serial_omap_request_port(struct uart_port *port)
1147 {
1148 dev_dbg(port->dev, "serial_omap_request_port+\n");
1149 return 0;
1150 }
1151
1152 static void serial_omap_config_port(struct uart_port *port, int flags)
1153 {
1154 struct uart_omap_port *up = to_uart_omap_port(port);
1155
1156 dev_dbg(up->port.dev, "serial_omap_config_port+%d\n",
1157 up->port.line);
1158 up->port.type = PORT_OMAP;
1159 up->port.flags |= UPF_SOFT_FLOW | UPF_HARD_FLOW;
1160 }
1161
1162 static int
1163 serial_omap_verify_port(struct uart_port *port, struct serial_struct *ser)
1164 {
1165 /* we don't want the core code to modify any port params */
1166 dev_dbg(port->dev, "serial_omap_verify_port+\n");
1167 return -EINVAL;
1168 }
1169
1170 static const char *
1171 serial_omap_type(struct uart_port *port)
1172 {
1173 struct uart_omap_port *up = to_uart_omap_port(port);
1174
1175 dev_dbg(up->port.dev, "serial_omap_type+%d\n", up->port.line);
1176 return up->name;
1177 }
1178
1179 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1180
1181 static inline void wait_for_xmitr(struct uart_omap_port *up)
1182 {
1183 unsigned int status, tmout = 10000;
1184
1185 /* Wait up to 10ms for the character(s) to be sent. */
1186 do {
1187 status = serial_in(up, UART_LSR);
1188
1189 if (status & UART_LSR_BI)
1190 up->lsr_break_flag = UART_LSR_BI;
1191
1192 if (--tmout == 0)
1193 break;
1194 udelay(1);
1195 } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
1196
1197 /* Wait up to 1s for flow control if necessary */
1198 if (up->port.flags & UPF_CONS_FLOW) {
1199 tmout = 1000000;
1200 for (tmout = 1000000; tmout; tmout--) {
1201 unsigned int msr = serial_in(up, UART_MSR);
1202
1203 up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
1204 if (msr & UART_MSR_CTS)
1205 break;
1206
1207 udelay(1);
1208 }
1209 }
1210 }
1211
1212 #ifdef CONFIG_CONSOLE_POLL
1213
1214 static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
1215 {
1216 struct uart_omap_port *up = to_uart_omap_port(port);
1217
1218 pm_runtime_get_sync(up->dev);
1219 wait_for_xmitr(up);
1220 serial_out(up, UART_TX, ch);
1221 pm_runtime_mark_last_busy(up->dev);
1222 pm_runtime_put_autosuspend(up->dev);
1223 }
1224
1225 static int serial_omap_poll_get_char(struct uart_port *port)
1226 {
1227 struct uart_omap_port *up = to_uart_omap_port(port);
1228 unsigned int status;
1229
1230 pm_runtime_get_sync(up->dev);
1231 status = serial_in(up, UART_LSR);
1232 if (!(status & UART_LSR_DR)) {
1233 status = NO_POLL_CHAR;
1234 goto out;
1235 }
1236
1237 status = serial_in(up, UART_RX);
1238
1239 out:
1240 pm_runtime_mark_last_busy(up->dev);
1241 pm_runtime_put_autosuspend(up->dev);
1242
1243 return status;
1244 }
1245
1246 #endif /* CONFIG_CONSOLE_POLL */
1247
1248 #ifdef CONFIG_SERIAL_OMAP_CONSOLE
1249
1250 static struct uart_omap_port *serial_omap_console_ports[OMAP_MAX_HSUART_PORTS];
1251
1252 static struct uart_driver serial_omap_reg;
1253
1254 static void serial_omap_console_putchar(struct uart_port *port, int ch)
1255 {
1256 struct uart_omap_port *up = to_uart_omap_port(port);
1257
1258 wait_for_xmitr(up);
1259 serial_out(up, UART_TX, ch);
1260 }
1261
1262 static void
1263 serial_omap_console_write(struct console *co, const char *s,
1264 unsigned int count)
1265 {
1266 struct uart_omap_port *up = serial_omap_console_ports[co->index];
1267 unsigned long flags;
1268 unsigned int ier;
1269 int locked = 1;
1270
1271 pm_runtime_get_sync(up->dev);
1272
1273 local_irq_save(flags);
1274 if (up->port.sysrq)
1275 locked = 0;
1276 else if (oops_in_progress)
1277 locked = spin_trylock(&up->port.lock);
1278 else
1279 spin_lock(&up->port.lock);
1280
1281 /*
1282 * First save the IER then disable the interrupts
1283 */
1284 ier = serial_in(up, UART_IER);
1285 serial_out(up, UART_IER, 0);
1286
1287 uart_console_write(&up->port, s, count, serial_omap_console_putchar);
1288
1289 /*
1290 * Finally, wait for transmitter to become empty
1291 * and restore the IER
1292 */
1293 wait_for_xmitr(up);
1294 serial_out(up, UART_IER, ier);
1295 /*
1296 * The receive handling will happen properly because the
1297 * receive ready bit will still be set; it is not cleared
1298 * on read. However, modem control will not, we must
1299 * call it if we have saved something in the saved flags
1300 * while processing with interrupts off.
1301 */
1302 if (up->msr_saved_flags)
1303 check_modem_status(up);
1304
1305 pm_runtime_mark_last_busy(up->dev);
1306 pm_runtime_put_autosuspend(up->dev);
1307 if (locked)
1308 spin_unlock(&up->port.lock);
1309 local_irq_restore(flags);
1310 }
1311
1312 static int __init
1313 serial_omap_console_setup(struct console *co, char *options)
1314 {
1315 struct uart_omap_port *up;
1316 int baud = 115200;
1317 int bits = 8;
1318 int parity = 'n';
1319 int flow = 'n';
1320
1321 if (serial_omap_console_ports[co->index] == NULL)
1322 return -ENODEV;
1323 up = serial_omap_console_ports[co->index];
1324
1325 if (options)
1326 uart_parse_options(options, &baud, &parity, &bits, &flow);
1327
1328 return uart_set_options(&up->port, co, baud, parity, bits, flow);
1329 }
1330
1331 static struct console serial_omap_console = {
1332 .name = OMAP_SERIAL_NAME,
1333 .write = serial_omap_console_write,
1334 .device = uart_console_device,
1335 .setup = serial_omap_console_setup,
1336 .flags = CON_PRINTBUFFER,
1337 .index = -1,
1338 .data = &serial_omap_reg,
1339 };
1340
1341 static void serial_omap_add_console_port(struct uart_omap_port *up)
1342 {
1343 serial_omap_console_ports[up->port.line] = up;
1344 }
1345
1346 #define OMAP_CONSOLE (&serial_omap_console)
1347
1348 #else
1349
1350 #define OMAP_CONSOLE NULL
1351
1352 static inline void serial_omap_add_console_port(struct uart_omap_port *up)
1353 {}
1354
1355 #endif
1356
1357 /* Enable or disable the rs485 support */
1358 static void
1359 serial_omap_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf)
1360 {
1361 struct uart_omap_port *up = to_uart_omap_port(port);
1362 unsigned long flags;
1363 unsigned int mode;
1364 int val;
1365
1366 pm_runtime_get_sync(up->dev);
1367 spin_lock_irqsave(&up->port.lock, flags);
1368
1369 /* Disable interrupts from this port */
1370 mode = up->ier;
1371 up->ier = 0;
1372 serial_out(up, UART_IER, 0);
1373
1374 /* store new config */
1375 up->rs485 = *rs485conf;
1376
1377 /*
1378 * Just as a precaution, only allow rs485
1379 * to be enabled if the gpio pin is valid
1380 */
1381 if (gpio_is_valid(up->rts_gpio)) {
1382 /* enable / disable rts */
1383 val = (up->rs485.flags & SER_RS485_ENABLED) ?
1384 SER_RS485_RTS_AFTER_SEND : SER_RS485_RTS_ON_SEND;
1385 val = (up->rs485.flags & val) ? 1 : 0;
1386 gpio_set_value(up->rts_gpio, val);
1387 } else
1388 up->rs485.flags &= ~SER_RS485_ENABLED;
1389
1390 /* Enable interrupts */
1391 up->ier = mode;
1392 serial_out(up, UART_IER, up->ier);
1393
1394 /* If RS-485 is disabled, make sure the THR interrupt is fired when
1395 * TX FIFO is below the trigger level.
1396 */
1397 if (!(up->rs485.flags & SER_RS485_ENABLED) &&
1398 (up->scr & OMAP_UART_SCR_TX_EMPTY)) {
1399 up->scr &= ~OMAP_UART_SCR_TX_EMPTY;
1400 serial_out(up, UART_OMAP_SCR, up->scr);
1401 }
1402
1403 spin_unlock_irqrestore(&up->port.lock, flags);
1404 pm_runtime_mark_last_busy(up->dev);
1405 pm_runtime_put_autosuspend(up->dev);
1406 }
1407
1408 static int
1409 serial_omap_ioctl(struct uart_port *port, unsigned int cmd, unsigned long arg)
1410 {
1411 struct serial_rs485 rs485conf;
1412
1413 switch (cmd) {
1414 case TIOCSRS485:
1415 if (copy_from_user(&rs485conf, (void __user *) arg,
1416 sizeof(rs485conf)))
1417 return -EFAULT;
1418
1419 serial_omap_config_rs485(port, &rs485conf);
1420 break;
1421
1422 case TIOCGRS485:
1423 if (copy_to_user((void __user *) arg,
1424 &(to_uart_omap_port(port)->rs485),
1425 sizeof(rs485conf)))
1426 return -EFAULT;
1427 break;
1428
1429 default:
1430 return -ENOIOCTLCMD;
1431 }
1432 return 0;
1433 }
1434
1435
1436 static struct uart_ops serial_omap_pops = {
1437 .tx_empty = serial_omap_tx_empty,
1438 .set_mctrl = serial_omap_set_mctrl,
1439 .get_mctrl = serial_omap_get_mctrl,
1440 .stop_tx = serial_omap_stop_tx,
1441 .start_tx = serial_omap_start_tx,
1442 .throttle = serial_omap_throttle,
1443 .unthrottle = serial_omap_unthrottle,
1444 .stop_rx = serial_omap_stop_rx,
1445 .enable_ms = serial_omap_enable_ms,
1446 .break_ctl = serial_omap_break_ctl,
1447 .startup = serial_omap_startup,
1448 .shutdown = serial_omap_shutdown,
1449 .set_termios = serial_omap_set_termios,
1450 .pm = serial_omap_pm,
1451 .type = serial_omap_type,
1452 .release_port = serial_omap_release_port,
1453 .request_port = serial_omap_request_port,
1454 .config_port = serial_omap_config_port,
1455 .verify_port = serial_omap_verify_port,
1456 .ioctl = serial_omap_ioctl,
1457 #ifdef CONFIG_CONSOLE_POLL
1458 .poll_put_char = serial_omap_poll_put_char,
1459 .poll_get_char = serial_omap_poll_get_char,
1460 #endif
1461 };
1462
1463 static struct uart_driver serial_omap_reg = {
1464 .owner = THIS_MODULE,
1465 .driver_name = "OMAP-SERIAL",
1466 .dev_name = OMAP_SERIAL_NAME,
1467 .nr = OMAP_MAX_HSUART_PORTS,
1468 .cons = OMAP_CONSOLE,
1469 };
1470
1471 #ifdef CONFIG_PM_SLEEP
1472 static int serial_omap_prepare(struct device *dev)
1473 {
1474 struct uart_omap_port *up = dev_get_drvdata(dev);
1475
1476 up->is_suspending = true;
1477
1478 return 0;
1479 }
1480
1481 static void serial_omap_complete(struct device *dev)
1482 {
1483 struct uart_omap_port *up = dev_get_drvdata(dev);
1484
1485 up->is_suspending = false;
1486 }
1487
1488 static int serial_omap_suspend(struct device *dev)
1489 {
1490 struct uart_omap_port *up = dev_get_drvdata(dev);
1491
1492 uart_suspend_port(&serial_omap_reg, &up->port);
1493 flush_work(&up->qos_work);
1494
1495 if (device_may_wakeup(dev))
1496 serial_omap_enable_wakeup(up, true);
1497 else
1498 serial_omap_enable_wakeup(up, false);
1499
1500 return 0;
1501 }
1502
1503 static int serial_omap_resume(struct device *dev)
1504 {
1505 struct uart_omap_port *up = dev_get_drvdata(dev);
1506
1507 if (device_may_wakeup(dev))
1508 serial_omap_enable_wakeup(up, false);
1509
1510 uart_resume_port(&serial_omap_reg, &up->port);
1511
1512 return 0;
1513 }
1514 #else
1515 #define serial_omap_prepare NULL
1516 #define serial_omap_complete NULL
1517 #endif /* CONFIG_PM_SLEEP */
1518
1519 static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
1520 {
1521 u32 mvr, scheme;
1522 u16 revision, major, minor;
1523
1524 mvr = readl(up->port.membase + (UART_OMAP_MVER << up->port.regshift));
1525
1526 /* Check revision register scheme */
1527 scheme = mvr >> OMAP_UART_MVR_SCHEME_SHIFT;
1528
1529 switch (scheme) {
1530 case 0: /* Legacy Scheme: OMAP2/3 */
1531 /* MINOR_REV[0:4], MAJOR_REV[4:7] */
1532 major = (mvr & OMAP_UART_LEGACY_MVR_MAJ_MASK) >>
1533 OMAP_UART_LEGACY_MVR_MAJ_SHIFT;
1534 minor = (mvr & OMAP_UART_LEGACY_MVR_MIN_MASK);
1535 break;
1536 case 1:
1537 /* New Scheme: OMAP4+ */
1538 /* MINOR_REV[0:5], MAJOR_REV[8:10] */
1539 major = (mvr & OMAP_UART_MVR_MAJ_MASK) >>
1540 OMAP_UART_MVR_MAJ_SHIFT;
1541 minor = (mvr & OMAP_UART_MVR_MIN_MASK);
1542 break;
1543 default:
1544 dev_warn(up->dev,
1545 "Unknown %s revision, defaulting to highest\n",
1546 up->name);
1547 /* highest possible revision */
1548 major = 0xff;
1549 minor = 0xff;
1550 }
1551
1552 /* normalize revision for the driver */
1553 revision = UART_BUILD_REVISION(major, minor);
1554
1555 switch (revision) {
1556 case OMAP_UART_REV_46:
1557 up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
1558 UART_ERRATA_i291_DMA_FORCEIDLE);
1559 break;
1560 case OMAP_UART_REV_52:
1561 up->errata |= (UART_ERRATA_i202_MDR1_ACCESS |
1562 UART_ERRATA_i291_DMA_FORCEIDLE);
1563 up->features |= OMAP_UART_WER_HAS_TX_WAKEUP;
1564 break;
1565 case OMAP_UART_REV_63:
1566 up->errata |= UART_ERRATA_i202_MDR1_ACCESS;
1567 up->features |= OMAP_UART_WER_HAS_TX_WAKEUP;
1568 break;
1569 default:
1570 break;
1571 }
1572 }
1573
1574 static struct omap_uart_port_info *of_get_uart_port_info(struct device *dev)
1575 {
1576 struct omap_uart_port_info *omap_up_info;
1577
1578 omap_up_info = devm_kzalloc(dev, sizeof(*omap_up_info), GFP_KERNEL);
1579 if (!omap_up_info)
1580 return NULL; /* out of memory */
1581
1582 of_property_read_u32(dev->of_node, "clock-frequency",
1583 &omap_up_info->uartclk);
1584 return omap_up_info;
1585 }
1586
1587 static int serial_omap_probe_rs485(struct uart_omap_port *up,
1588 struct device_node *np)
1589 {
1590 struct serial_rs485 *rs485conf = &up->rs485;
1591 u32 rs485_delay[2];
1592 enum of_gpio_flags flags;
1593 int ret;
1594
1595 rs485conf->flags = 0;
1596 up->rts_gpio = -EINVAL;
1597
1598 if (!np)
1599 return 0;
1600
1601 if (of_property_read_bool(np, "rs485-rts-active-high"))
1602 rs485conf->flags |= SER_RS485_RTS_ON_SEND;
1603 else
1604 rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
1605
1606 /* check for tx enable gpio */
1607 up->rts_gpio = of_get_named_gpio_flags(np, "rts-gpio", 0, &flags);
1608 if (gpio_is_valid(up->rts_gpio)) {
1609 ret = devm_gpio_request(up->dev, up->rts_gpio, "omap-serial");
1610 if (ret < 0)
1611 return ret;
1612 ret = gpio_direction_output(up->rts_gpio,
1613 flags & SER_RS485_RTS_AFTER_SEND);
1614 if (ret < 0)
1615 return ret;
1616 } else if (up->rts_gpio == -EPROBE_DEFER) {
1617 return -EPROBE_DEFER;
1618 } else {
1619 up->rts_gpio = -EINVAL;
1620 }
1621
1622 if (of_property_read_u32_array(np, "rs485-rts-delay",
1623 rs485_delay, 2) == 0) {
1624 rs485conf->delay_rts_before_send = rs485_delay[0];
1625 rs485conf->delay_rts_after_send = rs485_delay[1];
1626 }
1627
1628 if (of_property_read_bool(np, "rs485-rx-during-tx"))
1629 rs485conf->flags |= SER_RS485_RX_DURING_TX;
1630
1631 if (of_property_read_bool(np, "linux,rs485-enabled-at-boot-time"))
1632 rs485conf->flags |= SER_RS485_ENABLED;
1633
1634 return 0;
1635 }
1636
1637 static int serial_omap_probe(struct platform_device *pdev)
1638 {
1639 struct omap_uart_port_info *omap_up_info = dev_get_platdata(&pdev->dev);
1640 struct uart_omap_port *up;
1641 struct resource *mem;
1642 void __iomem *base;
1643 int uartirq = 0;
1644 int wakeirq = 0;
1645 int ret;
1646
1647 /* The optional wakeirq may be specified in the board dts file */
1648 if (pdev->dev.of_node) {
1649 uartirq = irq_of_parse_and_map(pdev->dev.of_node, 0);
1650 if (!uartirq)
1651 return -EPROBE_DEFER;
1652 wakeirq = irq_of_parse_and_map(pdev->dev.of_node, 1);
1653 omap_up_info = of_get_uart_port_info(&pdev->dev);
1654 pdev->dev.platform_data = omap_up_info;
1655 } else {
1656 uartirq = platform_get_irq(pdev, 0);
1657 if (uartirq < 0)
1658 return -EPROBE_DEFER;
1659 }
1660
1661 up = devm_kzalloc(&pdev->dev, sizeof(*up), GFP_KERNEL);
1662 if (!up)
1663 return -ENOMEM;
1664
1665 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1666 base = devm_ioremap_resource(&pdev->dev, mem);
1667 if (IS_ERR(base))
1668 return PTR_ERR(base);
1669
1670 up->dev = &pdev->dev;
1671 up->port.dev = &pdev->dev;
1672 up->port.type = PORT_OMAP;
1673 up->port.iotype = UPIO_MEM;
1674 up->port.irq = uartirq;
1675 up->wakeirq = wakeirq;
1676 if (!up->wakeirq)
1677 dev_info(up->port.dev, "no wakeirq for uart%d\n",
1678 up->port.line);
1679
1680 up->port.regshift = 2;
1681 up->port.fifosize = 64;
1682 up->port.ops = &serial_omap_pops;
1683
1684 if (pdev->dev.of_node)
1685 up->port.line = of_alias_get_id(pdev->dev.of_node, "serial");
1686 else
1687 up->port.line = pdev->id;
1688
1689 if (up->port.line < 0) {
1690 dev_err(&pdev->dev, "failed to get alias/pdev id, errno %d\n",
1691 up->port.line);
1692 ret = -ENODEV;
1693 goto err_port_line;
1694 }
1695
1696 ret = serial_omap_probe_rs485(up, pdev->dev.of_node);
1697 if (ret < 0)
1698 goto err_rs485;
1699
1700 sprintf(up->name, "OMAP UART%d", up->port.line);
1701 up->port.mapbase = mem->start;
1702 up->port.membase = base;
1703 up->port.flags = omap_up_info->flags;
1704 up->port.uartclk = omap_up_info->uartclk;
1705 if (!up->port.uartclk) {
1706 up->port.uartclk = DEFAULT_CLK_SPEED;
1707 dev_warn(&pdev->dev,
1708 "No clock speed specified: using default: %d\n",
1709 DEFAULT_CLK_SPEED);
1710 }
1711
1712 up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
1713 up->calc_latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
1714 pm_qos_add_request(&up->pm_qos_request,
1715 PM_QOS_CPU_DMA_LATENCY, up->latency);
1716 INIT_WORK(&up->qos_work, serial_omap_uart_qos_work);
1717
1718 platform_set_drvdata(pdev, up);
1719 if (omap_up_info->autosuspend_timeout == 0)
1720 omap_up_info->autosuspend_timeout = -1;
1721
1722 device_init_wakeup(up->dev, true);
1723 pm_runtime_use_autosuspend(&pdev->dev);
1724 pm_runtime_set_autosuspend_delay(&pdev->dev,
1725 omap_up_info->autosuspend_timeout);
1726
1727 pm_runtime_irq_safe(&pdev->dev);
1728 pm_runtime_enable(&pdev->dev);
1729
1730 pm_runtime_get_sync(&pdev->dev);
1731
1732 omap_serial_fill_features_erratas(up);
1733
1734 ui[up->port.line] = up;
1735 serial_omap_add_console_port(up);
1736
1737 ret = uart_add_one_port(&serial_omap_reg, &up->port);
1738 if (ret != 0)
1739 goto err_add_port;
1740
1741 pm_runtime_mark_last_busy(up->dev);
1742 pm_runtime_put_autosuspend(up->dev);
1743 return 0;
1744
1745 err_add_port:
1746 pm_runtime_put(&pdev->dev);
1747 pm_runtime_disable(&pdev->dev);
1748 err_rs485:
1749 err_port_line:
1750 dev_err(&pdev->dev, "[UART%d]: failure [%s]: %d\n",
1751 pdev->id, __func__, ret);
1752 return ret;
1753 }
1754
1755 static int serial_omap_remove(struct platform_device *dev)
1756 {
1757 struct uart_omap_port *up = platform_get_drvdata(dev);
1758
1759 pm_runtime_put_sync(up->dev);
1760 pm_runtime_disable(up->dev);
1761 uart_remove_one_port(&serial_omap_reg, &up->port);
1762 pm_qos_remove_request(&up->pm_qos_request);
1763 device_init_wakeup(&dev->dev, false);
1764
1765 return 0;
1766 }
1767
1768 /*
1769 * Work Around for Errata i202 (2430, 3430, 3630, 4430 and 4460)
1770 * The access to uart register after MDR1 Access
1771 * causes UART to corrupt data.
1772 *
1773 * Need a delay =
1774 * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
1775 * give 10 times as much
1776 */
1777 static void serial_omap_mdr1_errataset(struct uart_omap_port *up, u8 mdr1)
1778 {
1779 u8 timeout = 255;
1780
1781 serial_out(up, UART_OMAP_MDR1, mdr1);
1782 udelay(2);
1783 serial_out(up, UART_FCR, up->fcr | UART_FCR_CLEAR_XMIT |
1784 UART_FCR_CLEAR_RCVR);
1785 /*
1786 * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
1787 * TX_FIFO_E bit is 1.
1788 */
1789 while (UART_LSR_THRE != (serial_in(up, UART_LSR) &
1790 (UART_LSR_THRE | UART_LSR_DR))) {
1791 timeout--;
1792 if (!timeout) {
1793 /* Should *never* happen. we warn and carry on */
1794 dev_crit(up->dev, "Errata i202: timedout %x\n",
1795 serial_in(up, UART_LSR));
1796 break;
1797 }
1798 udelay(1);
1799 }
1800 }
1801
1802 #ifdef CONFIG_PM_RUNTIME
1803 static void serial_omap_restore_context(struct uart_omap_port *up)
1804 {
1805 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1806 serial_omap_mdr1_errataset(up, UART_OMAP_MDR1_DISABLE);
1807 else
1808 serial_out(up, UART_OMAP_MDR1, UART_OMAP_MDR1_DISABLE);
1809
1810 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
1811 serial_out(up, UART_EFR, UART_EFR_ECB);
1812 serial_out(up, UART_LCR, 0x0); /* Operational mode */
1813 serial_out(up, UART_IER, 0x0);
1814 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
1815 serial_out(up, UART_DLL, up->dll);
1816 serial_out(up, UART_DLM, up->dlh);
1817 serial_out(up, UART_LCR, 0x0); /* Operational mode */
1818 serial_out(up, UART_IER, up->ier);
1819 serial_out(up, UART_FCR, up->fcr);
1820 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
1821 serial_out(up, UART_MCR, up->mcr);
1822 serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /* Config B mode */
1823 serial_out(up, UART_OMAP_SCR, up->scr);
1824 serial_out(up, UART_EFR, up->efr);
1825 serial_out(up, UART_LCR, up->lcr);
1826 if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
1827 serial_omap_mdr1_errataset(up, up->mdr1);
1828 else
1829 serial_out(up, UART_OMAP_MDR1, up->mdr1);
1830 serial_out(up, UART_OMAP_WER, up->wer);
1831 }
1832
1833 static int serial_omap_runtime_suspend(struct device *dev)
1834 {
1835 struct uart_omap_port *up = dev_get_drvdata(dev);
1836
1837 if (!up)
1838 return -EINVAL;
1839
1840 /*
1841 * When using 'no_console_suspend', the console UART must not be
1842 * suspended. Since driver suspend is managed by runtime suspend,
1843 * preventing runtime suspend (by returning error) will keep device
1844 * active during suspend.
1845 */
1846 if (up->is_suspending && !console_suspend_enabled &&
1847 uart_console(&up->port))
1848 return -EBUSY;
1849
1850 up->context_loss_cnt = serial_omap_get_context_loss_count(up);
1851
1852 serial_omap_enable_wakeup(up, true);
1853
1854 up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
1855 schedule_work(&up->qos_work);
1856
1857 return 0;
1858 }
1859
1860 static int serial_omap_runtime_resume(struct device *dev)
1861 {
1862 struct uart_omap_port *up = dev_get_drvdata(dev);
1863
1864 int loss_cnt = serial_omap_get_context_loss_count(up);
1865
1866 serial_omap_enable_wakeup(up, false);
1867
1868 if (loss_cnt < 0) {
1869 dev_dbg(dev, "serial_omap_get_context_loss_count failed : %d\n",
1870 loss_cnt);
1871 serial_omap_restore_context(up);
1872 } else if (up->context_loss_cnt != loss_cnt) {
1873 serial_omap_restore_context(up);
1874 }
1875 up->latency = up->calc_latency;
1876 schedule_work(&up->qos_work);
1877
1878 return 0;
1879 }
1880 #endif
1881
1882 static const struct dev_pm_ops serial_omap_dev_pm_ops = {
1883 SET_SYSTEM_SLEEP_PM_OPS(serial_omap_suspend, serial_omap_resume)
1884 SET_RUNTIME_PM_OPS(serial_omap_runtime_suspend,
1885 serial_omap_runtime_resume, NULL)
1886 .prepare = serial_omap_prepare,
1887 .complete = serial_omap_complete,
1888 };
1889
1890 #if defined(CONFIG_OF)
1891 static const struct of_device_id omap_serial_of_match[] = {
1892 { .compatible = "ti,omap2-uart" },
1893 { .compatible = "ti,omap3-uart" },
1894 { .compatible = "ti,omap4-uart" },
1895 {},
1896 };
1897 MODULE_DEVICE_TABLE(of, omap_serial_of_match);
1898 #endif
1899
1900 static struct platform_driver serial_omap_driver = {
1901 .probe = serial_omap_probe,
1902 .remove = serial_omap_remove,
1903 .driver = {
1904 .name = DRIVER_NAME,
1905 .pm = &serial_omap_dev_pm_ops,
1906 .of_match_table = of_match_ptr(omap_serial_of_match),
1907 },
1908 };
1909
1910 static int __init serial_omap_init(void)
1911 {
1912 int ret;
1913
1914 ret = uart_register_driver(&serial_omap_reg);
1915 if (ret != 0)
1916 return ret;
1917 ret = platform_driver_register(&serial_omap_driver);
1918 if (ret != 0)
1919 uart_unregister_driver(&serial_omap_reg);
1920 return ret;
1921 }
1922
1923 static void __exit serial_omap_exit(void)
1924 {
1925 platform_driver_unregister(&serial_omap_driver);
1926 uart_unregister_driver(&serial_omap_reg);
1927 }
1928
1929 module_init(serial_omap_init);
1930 module_exit(serial_omap_exit);
1931
1932 MODULE_DESCRIPTION("OMAP High Speed UART driver");
1933 MODULE_LICENSE("GPL");
1934 MODULE_AUTHOR("Texas Instruments Inc");
Linux kernel - Deliverables
This page took 0.062031 seconds and 4 git commands to generate.