From a619f981b477035027dd27dfbee6148b4cd4a83c Mon Sep 17 00:00:00 2001 From: Akira Iguchi Date: Fri, 26 Jan 2007 16:28:18 +0900 Subject: [PATCH] libata: PATA driver for Celleb This is the patch for PATA controller of Celleb. This driver uses the managed iomap (devres). Because this driver needs special taskfile accesses, there is a copy of ata_std_softreset(). ata_dev_try_classify() is exported so that it can be used in this function. Signed-off-by: Kou Ishizaki Signed-off-by: Akira Iguchi Signed-off-by: Jeff Garzik --- drivers/ata/Kconfig | 9 + drivers/ata/Makefile | 1 + drivers/ata/libata-core.c | 3 +- drivers/ata/pata_scc.c | 1228 +++++++++++++++++++++++++++++++++++++ include/linux/libata.h | 1 + 5 files changed, 1241 insertions(+), 1 deletion(-) create mode 100644 drivers/ata/pata_scc.c diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index 4af0a4bb5780..376d2cdde009 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -562,6 +562,15 @@ config PATA_IXP4XX_CF If unsure, say N. +config PATA_SCC + tristate "Toshiba's Cell Reference Set IDE support" + depends on PCI + help + This option enables support for the built-in IDE controller on + Toshiba Cell Reference Board. + + If unsure, say N. + endif endmenu diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile index 74298afbbaa7..13d7397e0008 100644 --- a/drivers/ata/Makefile +++ b/drivers/ata/Makefile @@ -59,6 +59,7 @@ obj-$(CONFIG_PATA_WINBOND_VLB) += pata_winbond.o obj-$(CONFIG_PATA_SIS) += pata_sis.o obj-$(CONFIG_PATA_TRIFLEX) += pata_triflex.o obj-$(CONFIG_PATA_IXP4XX_CF) += pata_ixp4xx_cf.o +obj-$(CONFIG_PATA_SCC) += pata_scc.o obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o # Should be last but one libata driver obj-$(CONFIG_ATA_GENERIC) += ata_generic.o diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index e900c5edefc4..9c54de5addff 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -708,7 +708,7 @@ unsigned int ata_dev_classify(const struct ata_taskfile *tf) * Device type - %ATA_DEV_ATA, %ATA_DEV_ATAPI or %ATA_DEV_NONE. */ -static unsigned int +unsigned int ata_dev_try_classify(struct ata_port *ap, unsigned int device, u8 *r_err) { struct ata_taskfile tf; @@ -6311,3 +6311,4 @@ EXPORT_SYMBOL_GPL(ata_irq_on); EXPORT_SYMBOL_GPL(ata_dummy_irq_on); EXPORT_SYMBOL_GPL(ata_irq_ack); EXPORT_SYMBOL_GPL(ata_dummy_irq_ack); +EXPORT_SYMBOL_GPL(ata_dev_try_classify); diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c new file mode 100644 index 000000000000..049a3a284729 --- /dev/null +++ b/drivers/ata/pata_scc.c @@ -0,0 +1,1228 @@ +/* + * Support for IDE interfaces on Celleb platform + * + * (C) Copyright 2006 TOSHIBA CORPORATION + * + * This code is based on drivers/ata/ata_piix.c: + * Copyright 2003-2005 Red Hat Inc + * Copyright 2003-2005 Jeff Garzik + * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer + * Copyright (C) 1998-2000 Andre Hedrick + * Copyright (C) 2003 Red Hat Inc + * + * and drivers/ata/ahci.c: + * Copyright 2004-2005 Red Hat, Inc. + * + * and drivers/ata/libata-core.c: + * Copyright 2003-2004 Red Hat, Inc. All rights reserved. + * Copyright 2003-2004 Jeff Garzik + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRV_NAME "pata_scc" +#define DRV_VERSION "0.1" + +#define PCI_DEVICE_ID_TOSHIBA_SCC_ATA 0x01b4 + +/* PCI BARs */ +#define SCC_CTRL_BAR 0 +#define SCC_BMID_BAR 1 + +/* offset of CTRL registers */ +#define SCC_CTL_PIOSHT 0x000 +#define SCC_CTL_PIOCT 0x004 +#define SCC_CTL_MDMACT 0x008 +#define SCC_CTL_MCRCST 0x00C +#define SCC_CTL_SDMACT 0x010 +#define SCC_CTL_SCRCST 0x014 +#define SCC_CTL_UDENVT 0x018 +#define SCC_CTL_TDVHSEL 0x020 +#define SCC_CTL_MODEREG 0x024 +#define SCC_CTL_ECMODE 0xF00 +#define SCC_CTL_MAEA0 0xF50 +#define SCC_CTL_MAEC0 0xF54 +#define SCC_CTL_CCKCTRL 0xFF0 + +/* offset of BMID registers */ +#define SCC_DMA_CMD 0x000 +#define SCC_DMA_STATUS 0x004 +#define SCC_DMA_TABLE_OFS 0x008 +#define SCC_DMA_INTMASK 0x010 +#define SCC_DMA_INTST 0x014 +#define SCC_DMA_PTERADD 0x018 +#define SCC_REG_CMD_ADDR 0x020 +#define SCC_REG_DATA 0x000 +#define SCC_REG_ERR 0x004 +#define SCC_REG_FEATURE 0x004 +#define SCC_REG_NSECT 0x008 +#define SCC_REG_LBAL 0x00C +#define SCC_REG_LBAM 0x010 +#define SCC_REG_LBAH 0x014 +#define SCC_REG_DEVICE 0x018 +#define SCC_REG_STATUS 0x01C +#define SCC_REG_CMD 0x01C +#define SCC_REG_ALTSTATUS 0x020 + +/* register value */ +#define TDVHSEL_MASTER 0x00000001 +#define TDVHSEL_SLAVE 0x00000004 + +#define MODE_JCUSFEN 0x00000080 + +#define ECMODE_VALUE 0x01 + +#define CCKCTRL_ATARESET 0x00040000 +#define CCKCTRL_BUFCNT 0x00020000 +#define CCKCTRL_CRST 0x00010000 +#define CCKCTRL_OCLKEN 0x00000100 +#define CCKCTRL_ATACLKOEN 0x00000002 +#define CCKCTRL_LCLKEN 0x00000001 + +#define QCHCD_IOS_SS 0x00000001 + +#define QCHSD_STPDIAG 0x00020000 + +#define INTMASK_MSK 0xD1000012 +#define INTSTS_SERROR 0x80000000 +#define INTSTS_PRERR 0x40000000 +#define INTSTS_RERR 0x10000000 +#define INTSTS_ICERR 0x01000000 +#define INTSTS_BMSINT 0x00000010 +#define INTSTS_BMHE 0x00000008 +#define INTSTS_IOIRQS 0x00000004 +#define INTSTS_INTRQ 0x00000002 +#define INTSTS_ACTEINT 0x00000001 + + +/* PIO transfer mode table */ +/* JCHST */ +static const unsigned long JCHSTtbl[2][7] = { + {0x0E, 0x05, 0x02, 0x03, 0x02, 0x00, 0x00}, /* 100MHz */ + {0x13, 0x07, 0x04, 0x04, 0x03, 0x00, 0x00} /* 133MHz */ +}; + +/* JCHHT */ +static const unsigned long JCHHTtbl[2][7] = { + {0x0E, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00}, /* 100MHz */ + {0x13, 0x03, 0x03, 0x03, 0x03, 0x00, 0x00} /* 133MHz */ +}; + +/* JCHCT */ +static const unsigned long JCHCTtbl[2][7] = { + {0x1D, 0x1D, 0x1C, 0x0B, 0x06, 0x00, 0x00}, /* 100MHz */ + {0x27, 0x26, 0x26, 0x0E, 0x09, 0x00, 0x00} /* 133MHz */ +}; + +/* DMA transfer mode table */ +/* JCHDCTM/JCHDCTS */ +static const unsigned long JCHDCTxtbl[2][7] = { + {0x0A, 0x06, 0x04, 0x03, 0x01, 0x00, 0x00}, /* 100MHz */ + {0x0E, 0x09, 0x06, 0x04, 0x02, 0x01, 0x00} /* 133MHz */ +}; + +/* JCSTWTM/JCSTWTS */ +static const unsigned long JCSTWTxtbl[2][7] = { + {0x06, 0x04, 0x03, 0x02, 0x02, 0x02, 0x00}, /* 100MHz */ + {0x09, 0x06, 0x04, 0x02, 0x02, 0x02, 0x02} /* 133MHz */ +}; + +/* JCTSS */ +static const unsigned long JCTSStbl[2][7] = { + {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x00}, /* 100MHz */ + {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x05} /* 133MHz */ +}; + +/* JCENVT */ +static const unsigned long JCENVTtbl[2][7] = { + {0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00}, /* 100MHz */ + {0x02, 0x02, 0x02, 0x02, 0x02, 0x02, 0x02} /* 133MHz */ +}; + +/* JCACTSELS/JCACTSELM */ +static const unsigned long JCACTSELtbl[2][7] = { + {0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00}, /* 100MHz */ + {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01} /* 133MHz */ +}; + +static const struct pci_device_id scc_pci_tbl[] = { + {PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { } /* terminate list */ +}; + +/** + * scc_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: um + * + * Set PIO mode for device. + * + * LOCKING: + * None (inherited from caller). + */ + +static void scc_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR]; + void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL; + void __iomem *piosht_port = ctrl_base + SCC_CTL_PIOSHT; + void __iomem *pioct_port = ctrl_base + SCC_CTL_PIOCT; + unsigned long reg; + int offset; + + reg = in_be32(cckctrl_port); + if (reg & CCKCTRL_ATACLKOEN) + offset = 1; /* 133MHz */ + else + offset = 0; /* 100MHz */ + + reg = JCHSTtbl[offset][pio] << 16 | JCHHTtbl[offset][pio]; + out_be32(piosht_port, reg); + reg = JCHCTtbl[offset][pio]; + out_be32(pioct_port, reg); +} + +/** + * scc_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: um + * @udma: udma mode, 0 - 6 + * + * Set UDMA mode for device. + * + * LOCKING: + * None (inherited from caller). + */ + +static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int udma = adev->dma_mode; + unsigned int is_slave = (adev->devno != 0); + u8 speed = udma; + void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR]; + void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL; + void __iomem *mdmact_port = ctrl_base + SCC_CTL_MDMACT; + void __iomem *mcrcst_port = ctrl_base + SCC_CTL_MCRCST; + void __iomem *sdmact_port = ctrl_base + SCC_CTL_SDMACT; + void __iomem *scrcst_port = ctrl_base + SCC_CTL_SCRCST; + void __iomem *udenvt_port = ctrl_base + SCC_CTL_UDENVT; + void __iomem *tdvhsel_port = ctrl_base + SCC_CTL_TDVHSEL; + int offset, idx; + + if (in_be32(cckctrl_port) & CCKCTRL_ATACLKOEN) + offset = 1; /* 133MHz */ + else + offset = 0; /* 100MHz */ + + if (speed >= XFER_UDMA_0) + idx = speed - XFER_UDMA_0; + else + return; + + if (is_slave) { + out_be32(sdmact_port, JCHDCTxtbl[offset][idx]); + out_be32(scrcst_port, JCSTWTxtbl[offset][idx]); + out_be32(tdvhsel_port, + (in_be32(tdvhsel_port) & ~TDVHSEL_SLAVE) | (JCACTSELtbl[offset][idx] << 2)); + } else { + out_be32(mdmact_port, JCHDCTxtbl[offset][idx]); + out_be32(mcrcst_port, JCSTWTxtbl[offset][idx]); + out_be32(tdvhsel_port, + (in_be32(tdvhsel_port) & ~TDVHSEL_MASTER) | JCACTSELtbl[offset][idx]); + } + out_be32(udenvt_port, + JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx]); +} + +/** + * scc_tf_load - send taskfile registers to host controller + * @ap: Port to which output is sent + * @tf: ATA taskfile register set + * + * Note: Original code is ata_tf_load(). + */ + +static void scc_tf_load (struct ata_port *ap, const struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; + + if (tf->ctl != ap->last_ctl) { + out_be32(ioaddr->ctl_addr, tf->ctl); + ap->last_ctl = tf->ctl; + ata_wait_idle(ap); + } + + if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { + out_be32(ioaddr->feature_addr, tf->hob_feature); + out_be32(ioaddr->nsect_addr, tf->hob_nsect); + out_be32(ioaddr->lbal_addr, tf->hob_lbal); + out_be32(ioaddr->lbam_addr, tf->hob_lbam); + out_be32(ioaddr->lbah_addr, tf->hob_lbah); + VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n", + tf->hob_feature, + tf->hob_nsect, + tf->hob_lbal, + tf->hob_lbam, + tf->hob_lbah); + } + + if (is_addr) { + out_be32(ioaddr->feature_addr, tf->feature); + out_be32(ioaddr->nsect_addr, tf->nsect); + out_be32(ioaddr->lbal_addr, tf->lbal); + out_be32(ioaddr->lbam_addr, tf->lbam); + out_be32(ioaddr->lbah_addr, tf->lbah); + VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n", + tf->feature, + tf->nsect, + tf->lbal, + tf->lbam, + tf->lbah); + } + + if (tf->flags & ATA_TFLAG_DEVICE) { + out_be32(ioaddr->device_addr, tf->device); + VPRINTK("device 0x%X\n", tf->device); + } + + ata_wait_idle(ap); +} + +/** + * scc_check_status - Read device status reg & clear interrupt + * @ap: port where the device is + * + * Note: Original code is ata_check_status(). + */ + +static u8 scc_check_status (struct ata_port *ap) +{ + return in_be32(ap->ioaddr.status_addr); +} + +/** + * scc_tf_read - input device's ATA taskfile shadow registers + * @ap: Port from which input is read + * @tf: ATA taskfile register set for storing input + * + * Note: Original code is ata_tf_read(). + */ + +static void scc_tf_read (struct ata_port *ap, struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + + tf->command = scc_check_status(ap); + tf->feature = in_be32(ioaddr->error_addr); + tf->nsect = in_be32(ioaddr->nsect_addr); + tf->lbal = in_be32(ioaddr->lbal_addr); + tf->lbam = in_be32(ioaddr->lbam_addr); + tf->lbah = in_be32(ioaddr->lbah_addr); + tf->device = in_be32(ioaddr->device_addr); + + if (tf->flags & ATA_TFLAG_LBA48) { + out_be32(ioaddr->ctl_addr, tf->ctl | ATA_HOB); + tf->hob_feature = in_be32(ioaddr->error_addr); + tf->hob_nsect = in_be32(ioaddr->nsect_addr); + tf->hob_lbal = in_be32(ioaddr->lbal_addr); + tf->hob_lbam = in_be32(ioaddr->lbam_addr); + tf->hob_lbah = in_be32(ioaddr->lbah_addr); + } +} + +/** + * scc_exec_command - issue ATA command to host controller + * @ap: port to which command is being issued + * @tf: ATA taskfile register set + * + * Note: Original code is ata_exec_command(). + */ + +static void scc_exec_command (struct ata_port *ap, + const struct ata_taskfile *tf) +{ + DPRINTK("ata%u: cmd 0x%X\n", ap->id, tf->command); + + out_be32(ap->ioaddr.command_addr, tf->command); + ata_pause(ap); +} + +/** + * scc_check_altstatus - Read device alternate status reg + * @ap: port where the device is + */ + +static u8 scc_check_altstatus (struct ata_port *ap) +{ + return in_be32(ap->ioaddr.altstatus_addr); +} + +/** + * scc_std_dev_select - Select device 0/1 on ATA bus + * @ap: ATA channel to manipulate + * @device: ATA device (numbered from zero) to select + * + * Note: Original code is ata_std_dev_select(). + */ + +static void scc_std_dev_select (struct ata_port *ap, unsigned int device) +{ + u8 tmp; + + if (device == 0) + tmp = ATA_DEVICE_OBS; + else + tmp = ATA_DEVICE_OBS | ATA_DEV1; + + out_be32(ap->ioaddr.device_addr, tmp); + ata_pause(ap); +} + +/** + * scc_bmdma_setup - Set up PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * Note: Original code is ata_bmdma_setup(). + */ + +static void scc_bmdma_setup (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u8 dmactl; + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + /* load PRD table addr */ + out_be32(mmio + SCC_DMA_TABLE_OFS, ap->prd_dma); + + /* specify data direction, triple-check start bit is clear */ + dmactl = in_be32(mmio + SCC_DMA_CMD); + dmactl &= ~(ATA_DMA_WR | ATA_DMA_START); + if (!rw) + dmactl |= ATA_DMA_WR; + out_be32(mmio + SCC_DMA_CMD, dmactl); + + /* issue r/w command */ + ap->ops->exec_command(ap, &qc->tf); +} + +/** + * scc_bmdma_start - Start a PCI IDE BMDMA transaction + * @qc: Info associated with this ATA transaction. + * + * Note: Original code is ata_bmdma_start(). + */ + +static void scc_bmdma_start (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + u8 dmactl; + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + /* start host DMA transaction */ + dmactl = in_be32(mmio + SCC_DMA_CMD); + out_be32(mmio + SCC_DMA_CMD, dmactl | ATA_DMA_START); +} + +/** + * scc_devchk - PATA device presence detection + * @ap: ATA channel to examine + * @device: Device to examine (starting at zero) + * + * Note: Original code is ata_devchk(). + */ + +static unsigned int scc_devchk (struct ata_port *ap, + unsigned int device) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + u8 nsect, lbal; + + ap->ops->dev_select(ap, device); + + out_be32(ioaddr->nsect_addr, 0x55); + out_be32(ioaddr->lbal_addr, 0xaa); + + out_be32(ioaddr->nsect_addr, 0xaa); + out_be32(ioaddr->lbal_addr, 0x55); + + out_be32(ioaddr->nsect_addr, 0x55); + out_be32(ioaddr->lbal_addr, 0xaa); + + nsect = in_be32(ioaddr->nsect_addr); + lbal = in_be32(ioaddr->lbal_addr); + + if ((nsect == 0x55) && (lbal == 0xaa)) + return 1; /* we found a device */ + + return 0; /* nothing found */ +} + +/** + * scc_bus_post_reset - PATA device post reset + * + * Note: Original code is ata_bus_post_reset(). + */ + +static void scc_bus_post_reset (struct ata_port *ap, unsigned int devmask) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + unsigned int dev0 = devmask & (1 << 0); + unsigned int dev1 = devmask & (1 << 1); + unsigned long timeout; + + /* if device 0 was found in ata_devchk, wait for its + * BSY bit to clear + */ + if (dev0) + ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT); + + /* if device 1 was found in ata_devchk, wait for + * register access, then wait for BSY to clear + */ + timeout = jiffies + ATA_TMOUT_BOOT; + while (dev1) { + u8 nsect, lbal; + + ap->ops->dev_select(ap, 1); + nsect = in_be32(ioaddr->nsect_addr); + lbal = in_be32(ioaddr->lbal_addr); + if ((nsect == 1) && (lbal == 1)) + break; + if (time_after(jiffies, timeout)) { + dev1 = 0; + break; + } + msleep(50); /* give drive a breather */ + } + if (dev1) + ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT); + + /* is all this really necessary? */ + ap->ops->dev_select(ap, 0); + if (dev1) + ap->ops->dev_select(ap, 1); + if (dev0) + ap->ops->dev_select(ap, 0); +} + +/** + * scc_bus_softreset - PATA device software reset + * + * Note: Original code is ata_bus_softreset(). + */ + +static unsigned int scc_bus_softreset (struct ata_port *ap, + unsigned int devmask) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + + DPRINTK("ata%u: bus reset via SRST\n", ap->id); + + /* software reset. causes dev0 to be selected */ + out_be32(ioaddr->ctl_addr, ap->ctl); + udelay(20); + out_be32(ioaddr->ctl_addr, ap->ctl | ATA_SRST); + udelay(20); + out_be32(ioaddr->ctl_addr, ap->ctl); + + /* spec mandates ">= 2ms" before checking status. + * We wait 150ms, because that was the magic delay used for + * ATAPI devices in Hale Landis's ATADRVR, for the period of time + * between when the ATA command register is written, and then + * status is checked. Because waiting for "a while" before + * checking status is fine, post SRST, we perform this magic + * delay here as well. + * + * Old drivers/ide uses the 2mS rule and then waits for ready + */ + msleep(150); + + /* Before we perform post reset processing we want to see if + * the bus shows 0xFF because the odd clown forgets the D7 + * pulldown resistor. + */ + if (scc_check_status(ap) == 0xFF) + return 0; + + scc_bus_post_reset(ap, devmask); + + return 0; +} + +/** + * scc_std_softreset - reset host port via ATA SRST + * @ap: port to reset + * @classes: resulting classes of attached devices + * + * Note: Original code is ata_std_softreset(). + */ + +static int scc_std_softreset (struct ata_port *ap, unsigned int *classes) +{ + unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS; + unsigned int devmask = 0, err_mask; + u8 err; + + DPRINTK("ENTER\n"); + + if (ata_port_offline(ap)) { + classes[0] = ATA_DEV_NONE; + goto out; + } + + /* determine if device 0/1 are present */ + if (scc_devchk(ap, 0)) + devmask |= (1 << 0); + if (slave_possible && scc_devchk(ap, 1)) + devmask |= (1 << 1); + + /* select device 0 again */ + ap->ops->dev_select(ap, 0); + + /* issue bus reset */ + DPRINTK("about to softreset, devmask=%x\n", devmask); + err_mask = scc_bus_softreset(ap, devmask); + if (err_mask) { + ata_port_printk(ap, KERN_ERR, "SRST failed (err_mask=0x%x)\n", + err_mask); + return -EIO; + } + + /* determine by signature whether we have ATA or ATAPI devices */ + classes[0] = ata_dev_try_classify(ap, 0, &err); + if (slave_possible && err != 0x81) + classes[1] = ata_dev_try_classify(ap, 1, &err); + + out: + DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]); + return 0; +} + +/** + * scc_bmdma_stop - Stop PCI IDE BMDMA transfer + * @qc: Command we are ending DMA for + */ + +static void scc_bmdma_stop (struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR]; + void __iomem *bmid_base = ap->host->iomap[SCC_BMID_BAR]; + u32 reg; + + while (1) { + reg = in_be32(bmid_base + SCC_DMA_INTST); + + if (reg & INTSTS_SERROR) { + printk(KERN_WARNING "%s: SERROR\n", DRV_NAME); + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_SERROR|INTSTS_BMSINT); + out_be32(bmid_base + SCC_DMA_CMD, + in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START); + continue; + } + + if (reg & INTSTS_PRERR) { + u32 maea0, maec0; + maea0 = in_be32(ctrl_base + SCC_CTL_MAEA0); + maec0 = in_be32(ctrl_base + SCC_CTL_MAEC0); + printk(KERN_WARNING "%s: PRERR [addr:%x cmd:%x]\n", DRV_NAME, maea0, maec0); + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_PRERR|INTSTS_BMSINT); + out_be32(bmid_base + SCC_DMA_CMD, + in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START); + continue; + } + + if (reg & INTSTS_RERR) { + printk(KERN_WARNING "%s: Response Error\n", DRV_NAME); + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_RERR|INTSTS_BMSINT); + out_be32(bmid_base + SCC_DMA_CMD, + in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START); + continue; + } + + if (reg & INTSTS_ICERR) { + out_be32(bmid_base + SCC_DMA_CMD, + in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START); + printk(KERN_WARNING "%s: Illegal Configuration\n", DRV_NAME); + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ICERR|INTSTS_BMSINT); + continue; + } + + if (reg & INTSTS_BMSINT) { + unsigned int classes; + printk(KERN_WARNING "%s: Internal Bus Error\n", DRV_NAME); + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMSINT); + /* TBD: SW reset */ + scc_std_softreset(ap, &classes); + continue; + } + + if (reg & INTSTS_BMHE) { + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMHE); + continue; + } + + if (reg & INTSTS_ACTEINT) { + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ACTEINT); + continue; + } + + if (reg & INTSTS_IOIRQS) { + out_be32(bmid_base + SCC_DMA_INTST, INTSTS_IOIRQS); + continue; + } + break; + } + + /* clear start/stop bit */ + out_be32(bmid_base + SCC_DMA_CMD, + in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START); + + /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */ + ata_altstatus(ap); /* dummy read */ +} + +/** + * scc_bmdma_status - Read PCI IDE BMDMA status + * @ap: Port associated with this ATA transaction. + */ + +static u8 scc_bmdma_status (struct ata_port *ap) +{ + u8 host_stat; + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + host_stat = in_be32(mmio + SCC_DMA_STATUS); + + /* Workaround for PTERADD: emulate DMA_INTR when + * - IDE_STATUS[ERR] = 1 + * - INT_STATUS[INTRQ] = 1 + * - DMA_STATUS[IORACTA] = 1 + */ + if (!(host_stat & ATA_DMA_INTR)) { + u32 int_status = in_be32(mmio + SCC_DMA_INTST); + if (ata_altstatus(ap) & ATA_ERR && + int_status & INTSTS_INTRQ && + host_stat & ATA_DMA_ACTIVE) + host_stat |= ATA_DMA_INTR; + } + + return host_stat; +} + +/** + * scc_data_xfer - Transfer data by PIO + * @adev: device for this I/O + * @buf: data buffer + * @buflen: buffer length + * @write_data: read/write + * + * Note: Original code is ata_data_xfer(). + */ + +static void scc_data_xfer (struct ata_device *adev, unsigned char *buf, + unsigned int buflen, int write_data) +{ + struct ata_port *ap = adev->ap; + unsigned int words = buflen >> 1; + unsigned int i; + u16 *buf16 = (u16 *) buf; + void __iomem *mmio = ap->ioaddr.data_addr; + + /* Transfer multiple of 2 bytes */ + if (write_data) { + for (i = 0; i < words; i++) + out_be32(mmio, cpu_to_le16(buf16[i])); + } else { + for (i = 0; i < words; i++) + buf16[i] = le16_to_cpu(in_be32(mmio)); + } + + /* Transfer trailing 1 byte, if any. */ + if (unlikely(buflen & 0x01)) { + u16 align_buf[1] = { 0 }; + unsigned char *trailing_buf = buf + buflen - 1; + + if (write_data) { + memcpy(align_buf, trailing_buf, 1); + out_be32(mmio, cpu_to_le16(align_buf[0])); + } else { + align_buf[0] = le16_to_cpu(in_be32(mmio)); + memcpy(trailing_buf, align_buf, 1); + } + } +} + +/** + * scc_irq_on - Enable interrupts on a port. + * @ap: Port on which interrupts are enabled. + * + * Note: Original code is ata_irq_on(). + */ + +static u8 scc_irq_on (struct ata_port *ap) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + u8 tmp; + + ap->ctl &= ~ATA_NIEN; + ap->last_ctl = ap->ctl; + + out_be32(ioaddr->ctl_addr, ap->ctl); + tmp = ata_wait_idle(ap); + + ap->ops->irq_clear(ap); + + return tmp; +} + +/** + * scc_irq_ack - Acknowledge a device interrupt. + * @ap: Port on which interrupts are enabled. + * + * Note: Original code is ata_irq_ack(). + */ + +static u8 scc_irq_ack (struct ata_port *ap, unsigned int chk_drq) +{ + unsigned int bits = chk_drq ? ATA_BUSY | ATA_DRQ : ATA_BUSY; + u8 host_stat, post_stat, status; + + status = ata_busy_wait(ap, bits, 1000); + if (status & bits) + if (ata_msg_err(ap)) + printk(KERN_ERR "abnormal status 0x%X\n", status); + + /* get controller status; clear intr, err bits */ + host_stat = in_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS); + out_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS, + host_stat | ATA_DMA_INTR | ATA_DMA_ERR); + + post_stat = in_be32(ap->ioaddr.bmdma_addr + SCC_DMA_STATUS); + + if (ata_msg_intr(ap)) + printk(KERN_INFO "%s: irq ack: host_stat 0x%X, new host_stat 0x%X, drv_stat 0x%X\n", + __FUNCTION__, + host_stat, post_stat, status); + + return status; +} + +/** + * scc_bmdma_freeze - Freeze BMDMA controller port + * @ap: port to freeze + * + * Note: Original code is ata_bmdma_freeze(). + */ + +static void scc_bmdma_freeze (struct ata_port *ap) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + + ap->ctl |= ATA_NIEN; + ap->last_ctl = ap->ctl; + + out_be32(ioaddr->ctl_addr, ap->ctl); + + /* Under certain circumstances, some controllers raise IRQ on + * ATA_NIEN manipulation. Also, many controllers fail to mask + * previously pending IRQ on ATA_NIEN assertion. Clear it. + */ + ata_chk_status(ap); + + ap->ops->irq_clear(ap); +} + +/** + * scc_pata_prereset - prepare for reset + * @ap: ATA port to be reset + */ + +static int scc_pata_prereset (struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA80; + return ata_std_prereset(ap); +} + +/** + * scc_std_postreset - standard postreset callback + * @ap: the target ata_port + * @classes: classes of attached devices + * + * Note: Original code is ata_std_postreset(). + */ + +static void scc_std_postreset (struct ata_port *ap, unsigned int *classes) +{ + DPRINTK("ENTER\n"); + + /* re-enable interrupts */ + if (!ap->ops->error_handler) + ap->ops->irq_on(ap); + + /* is double-select really necessary? */ + if (classes[0] != ATA_DEV_NONE) + ap->ops->dev_select(ap, 1); + if (classes[1] != ATA_DEV_NONE) + ap->ops->dev_select(ap, 0); + + /* bail out if no device is present */ + if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) { + DPRINTK("EXIT, no device\n"); + return; + } + + /* set up device control */ + if (ap->ioaddr.ctl_addr) + out_be32(ap->ioaddr.ctl_addr, ap->ctl); + + DPRINTK("EXIT\n"); +} + +/** + * scc_error_handler - Stock error handler for BMDMA controller + * @ap: port to handle error for + */ + +static void scc_error_handler (struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, scc_pata_prereset, scc_std_softreset, NULL, + scc_std_postreset); +} + +/** + * scc_bmdma_irq_clear - Clear PCI IDE BMDMA interrupt. + * @ap: Port associated with this ATA transaction. + * + * Note: Original code is ata_bmdma_irq_clear(). + */ + +static void scc_bmdma_irq_clear (struct ata_port *ap) +{ + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + if (!mmio) + return; + + out_be32(mmio + SCC_DMA_STATUS, in_be32(mmio + SCC_DMA_STATUS)); +} + +/** + * scc_port_start - Set port up for dma. + * @ap: Port to initialize + * + * Allocate space for PRD table using ata_port_start(). + * Set PRD table address for PTERADD. (PRD Transfer End Read) + */ + +static int scc_port_start (struct ata_port *ap) +{ + void __iomem *mmio = ap->ioaddr.bmdma_addr; + int rc; + + rc = ata_port_start(ap); + if (rc) + return rc; + + out_be32(mmio + SCC_DMA_PTERADD, ap->prd_dma); + return 0; +} + +/** + * scc_port_stop - Undo scc_port_start() + * @ap: Port to shut down + * + * Reset PTERADD. + */ + +static void scc_port_stop (struct ata_port *ap) +{ + void __iomem *mmio = ap->ioaddr.bmdma_addr; + + out_be32(mmio + SCC_DMA_PTERADD, 0); +} + +static struct scsi_host_template scc_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .slave_destroy = ata_scsi_slave_destroy, + .bios_param = ata_std_bios_param, + .resume = ata_scsi_device_resume, + .suspend = ata_scsi_device_suspend, +}; + +static const struct ata_port_operations scc_pata_ops = { + .port_disable = ata_port_disable, + .set_piomode = scc_set_piomode, + .set_dmamode = scc_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = scc_tf_load, + .tf_read = scc_tf_read, + .exec_command = scc_exec_command, + .check_status = scc_check_status, + .check_altstatus = scc_check_altstatus, + .dev_select = scc_std_dev_select, + + .bmdma_setup = scc_bmdma_setup, + .bmdma_start = scc_bmdma_start, + .bmdma_stop = scc_bmdma_stop, + .bmdma_status = scc_bmdma_status, + .data_xfer = scc_data_xfer, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + + .freeze = scc_bmdma_freeze, + .error_handler = scc_error_handler, + .post_internal_cmd = scc_bmdma_stop, + + .irq_handler = ata_interrupt, + .irq_clear = scc_bmdma_irq_clear, + .irq_on = scc_irq_on, + .irq_ack = scc_irq_ack, + + .port_start = scc_port_start, + .port_stop = scc_port_stop, +}; + +static struct ata_port_info scc_port_info[] = { + { + .sht = &scc_sht, + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_MMIO | ATA_FLAG_NO_LEGACY, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x00, + .udma_mask = ATA_UDMA6, + .port_ops = &scc_pata_ops, + }, +}; + +/** + * scc_reset_controller - initialize SCC PATA controller. + */ + +static int scc_reset_controller(struct ata_probe_ent *probe_ent) +{ + void __iomem *ctrl_base = probe_ent->iomap[SCC_CTRL_BAR]; + void __iomem *bmid_base = probe_ent->iomap[SCC_BMID_BAR]; + void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL; + void __iomem *mode_port = ctrl_base + SCC_CTL_MODEREG; + void __iomem *ecmode_port = ctrl_base + SCC_CTL_ECMODE; + void __iomem *intmask_port = bmid_base + SCC_DMA_INTMASK; + void __iomem *dmastatus_port = bmid_base + SCC_DMA_STATUS; + u32 reg = 0; + + out_be32(cckctrl_port, reg); + reg |= CCKCTRL_ATACLKOEN; + out_be32(cckctrl_port, reg); + reg |= CCKCTRL_LCLKEN | CCKCTRL_OCLKEN; + out_be32(cckctrl_port, reg); + reg |= CCKCTRL_CRST; + out_be32(cckctrl_port, reg); + + for (;;) { + reg = in_be32(cckctrl_port); + if (reg & CCKCTRL_CRST) + break; + udelay(5000); + } + + reg |= CCKCTRL_ATARESET; + out_be32(cckctrl_port, reg); + out_be32(ecmode_port, ECMODE_VALUE); + out_be32(mode_port, MODE_JCUSFEN); + out_be32(intmask_port, INTMASK_MSK); + + if (in_be32(dmastatus_port) & QCHSD_STPDIAG) { + printk(KERN_WARNING "%s: failed to detect 80c cable. (PDIAG# is high)\n", DRV_NAME); + return -EIO; + } + + return 0; +} + +/** + * scc_setup_ports - initialize ioaddr with SCC PATA port offsets. + * @ioaddr: IO address structure to be initialized + * @base: base address of BMID region + */ + +static void scc_setup_ports (struct ata_ioports *ioaddr, void __iomem *base) +{ + ioaddr->cmd_addr = base + SCC_REG_CMD_ADDR; + ioaddr->altstatus_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS; + ioaddr->ctl_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS; + ioaddr->bmdma_addr = base; + ioaddr->data_addr = ioaddr->cmd_addr + SCC_REG_DATA; + ioaddr->error_addr = ioaddr->cmd_addr + SCC_REG_ERR; + ioaddr->feature_addr = ioaddr->cmd_addr + SCC_REG_FEATURE; + ioaddr->nsect_addr = ioaddr->cmd_addr + SCC_REG_NSECT; + ioaddr->lbal_addr = ioaddr->cmd_addr + SCC_REG_LBAL; + ioaddr->lbam_addr = ioaddr->cmd_addr + SCC_REG_LBAM; + ioaddr->lbah_addr = ioaddr->cmd_addr + SCC_REG_LBAH; + ioaddr->device_addr = ioaddr->cmd_addr + SCC_REG_DEVICE; + ioaddr->status_addr = ioaddr->cmd_addr + SCC_REG_STATUS; + ioaddr->command_addr = ioaddr->cmd_addr + SCC_REG_CMD; +} + +static int scc_host_init(struct ata_probe_ent *probe_ent) +{ + struct pci_dev *pdev = to_pci_dev(probe_ent->dev); + int rc; + + rc = scc_reset_controller(probe_ent); + if (rc) + return rc; + + probe_ent->n_ports = 1; + + rc = pci_set_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + return rc; + rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK); + if (rc) + return rc; + + scc_setup_ports(&probe_ent->port[0], probe_ent->iomap[SCC_BMID_BAR]); + + pci_set_master(pdev); + + return 0; +} + +/** + * scc_init_one - Register SCC PATA device with kernel services + * @pdev: PCI device to register + * @ent: Entry in scc_pci_tbl matching with @pdev + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int scc_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version; + unsigned int board_idx = (unsigned int) ent->driver_data; + struct device *dev = &pdev->dev; + struct ata_probe_ent *probe_ent; + int rc; + + if (!printed_version++) + dev_printk(KERN_DEBUG, &pdev->dev, + "version " DRV_VERSION "\n"); + + rc = pcim_enable_device(pdev); + if (rc) + return rc; + + rc = pcim_iomap_regions(pdev, (1 << SCC_CTRL_BAR) | (1 << SCC_BMID_BAR), DRV_NAME); + if (rc == -EBUSY) + pcim_pin_device(pdev); + if (rc) + return rc; + + probe_ent = devm_kzalloc(dev, sizeof(*probe_ent), GFP_KERNEL); + if (!probe_ent) + return -ENOMEM; + + probe_ent->dev = dev; + INIT_LIST_HEAD(&probe_ent->node); + + probe_ent->sht = scc_port_info[board_idx].sht; + probe_ent->port_flags = scc_port_info[board_idx].flags; + probe_ent->pio_mask = scc_port_info[board_idx].pio_mask; + probe_ent->udma_mask = scc_port_info[board_idx].udma_mask; + probe_ent->port_ops = scc_port_info[board_idx].port_ops; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = IRQF_SHARED; + probe_ent->iomap = pcim_iomap_table(pdev); + + rc = scc_host_init(probe_ent); + if (rc) + return rc; + + if (!ata_device_add(probe_ent)) + return -ENODEV; + + devm_kfree(dev, probe_ent); + return 0; +} + +static struct pci_driver scc_pci_driver = { + .name = DRV_NAME, + .id_table = scc_pci_tbl, + .probe = scc_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +static int __init scc_init (void) +{ + int rc; + + DPRINTK("pci_register_driver\n"); + rc = pci_register_driver(&scc_pci_driver); + if (rc) + return rc; + + DPRINTK("done\n"); + return 0; +} + +static void __exit scc_exit (void) +{ + pci_unregister_driver(&scc_pci_driver); +} + +module_init(scc_init); +module_exit(scc_exit); + +MODULE_AUTHOR("Toshiba corp"); +MODULE_DESCRIPTION("SCSI low-level driver for Toshiba SCC PATA controller"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, scc_pci_tbl); +MODULE_VERSION(DRV_VERSION); diff --git a/include/linux/libata.h b/include/linux/libata.h index 86762a9f52ba..60dfc5f7e882 100644 --- a/include/linux/libata.h +++ b/include/linux/libata.h @@ -759,6 +759,7 @@ extern void ata_port_queue_task(struct ata_port *ap, work_func_t fn, extern u32 ata_wait_register(void __iomem *reg, u32 mask, u32 val, unsigned long interval_msec, unsigned long timeout_msec); +extern unsigned int ata_dev_try_classify(struct ata_port *, unsigned int, u8 *); /* * Default driver ops implementations -- 2.34.1