From 13e0fe49f676607688da7475c33540ec5dac53b5 Mon Sep 17 00:00:00 2001 From: Dmitry Eremin-Solenikov Date: Thu, 2 Jun 2011 18:51:14 +0400 Subject: [PATCH] mtd: drop physmap_configure physmap_configure() and physmap_set_partitions() have no users in kernel. Out of kernel users should have been converted to regular platform device long ago. Drop support for this obsolete API. Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Artem Bityutskiy --- drivers/mtd/maps/Kconfig | 6 ------ drivers/mtd/maps/physmap.c | 15 --------------- include/linux/mtd/physmap.h | 17 ----------------- 3 files changed, 38 deletions(-) diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig index 11cc2307c2ca..46eca3b3bcb0 100644 --- a/drivers/mtd/maps/Kconfig +++ b/drivers/mtd/maps/Kconfig @@ -41,8 +41,6 @@ config MTD_PHYSMAP_START are mapped on your particular target board. Refer to the memory map which should hopefully be in the documentation for your board. - Ignore this option if you use run-time physmap configuration - (i.e., run-time calling physmap_configure()). config MTD_PHYSMAP_LEN hex "Physical length of flash mapping" @@ -55,8 +53,6 @@ config MTD_PHYSMAP_LEN than the total amount of flash present. Refer to the memory map which should hopefully be in the documentation for your board. - Ignore this option if you use run-time physmap configuration - (i.e., run-time calling physmap_configure()). config MTD_PHYSMAP_BANKWIDTH int "Bank width in octets" @@ -67,8 +63,6 @@ config MTD_PHYSMAP_BANKWIDTH in octets. For example, if you have a data bus width of 32 bits, you would set the bus width octet value to 4. This is used internally by the CFI drivers. - Ignore this option if you use run-time physmap configuration - (i.e., run-time calling physmap_configure()). config MTD_PHYSMAP_OF tristate "Flash device in physical memory map based on OF description" diff --git a/drivers/mtd/maps/physmap.c b/drivers/mtd/maps/physmap.c index f64cee4a3bfb..2174d103297e 100644 --- a/drivers/mtd/maps/physmap.c +++ b/drivers/mtd/maps/physmap.c @@ -245,21 +245,6 @@ static struct platform_device physmap_flash = { .num_resources = 1, .resource = &physmap_flash_resource, }; - -void physmap_configure(unsigned long addr, unsigned long size, - int bankwidth, void (*set_vpp)(struct map_info *, int)) -{ - physmap_flash_resource.start = addr; - physmap_flash_resource.end = addr + size - 1; - physmap_flash_data.width = bankwidth; - physmap_flash_data.set_vpp = set_vpp; -} - -void physmap_set_partitions(struct mtd_partition *parts, int num_parts) -{ - physmap_flash_data.nr_parts = num_parts; - physmap_flash_data.parts = parts; -} #endif static int __init physmap_init(void) diff --git a/include/linux/mtd/physmap.h b/include/linux/mtd/physmap.h index e5f21d293c70..04e018160e2b 100644 --- a/include/linux/mtd/physmap.h +++ b/include/linux/mtd/physmap.h @@ -32,21 +32,4 @@ struct physmap_flash_data { struct mtd_partition *parts; }; -/* - * Board needs to specify the exact mapping during their setup time. - */ -void physmap_configure(unsigned long addr, unsigned long size, - int bankwidth, void (*set_vpp)(struct map_info *, int) ); - -/* - * Machines that wish to do flash partition may want to call this function in - * their setup routine. - * - * physmap_set_partitions(mypartitions, num_parts); - * - * Note that one can always override this hard-coded partition with - * command line partition (you need to enable CONFIG_MTD_CMDLINE_PARTS). - */ -void physmap_set_partitions(struct mtd_partition *parts, int num_parts); - #endif /* __LINUX_MTD_PHYSMAP__ */ -- 2.34.1