From 37a0186fdef963a5345dc076d32779147acfa6cb Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Fri, 21 Nov 2014 14:30:13 +0100 Subject: [PATCH] ARM: at91: remove at91rm9200 legacy boards files Remove old board files that use at91rm9200 Atmel SoC. The device tree is mature on this SoCs. It must be used now. Signed-off-by: Nicolas Ferre Acked-by: Boris BREZILLON --- arch/arm/mach-at91/Makefile | 15 - arch/arm/mach-at91/board-1arm.c | 99 ----- arch/arm/mach-at91/board-carmeva.c | 167 ------- arch/arm/mach-at91/board-cpuat91.c | 189 -------- arch/arm/mach-at91/board-csb337.c | 260 ----------- arch/arm/mach-at91/board-csb637.c | 142 ------ arch/arm/mach-at91/board-eb9200.c | 126 ------ arch/arm/mach-at91/board-ecbat91.c | 191 -------- arch/arm/mach-at91/board-eco920.c | 160 ------- arch/arm/mach-at91/board-kafa.c | 113 ----- arch/arm/mach-at91/board-kb9202.c | 159 ------- arch/arm/mach-at91/board-picotux200.c | 129 ------ arch/arm/mach-at91/board-rm9200ek.c | 196 --------- arch/arm/mach-at91/board-yl-9200.c | 597 -------------------------- 14 files changed, 2543 deletions(-) delete mode 100644 arch/arm/mach-at91/board-1arm.c delete mode 100644 arch/arm/mach-at91/board-carmeva.c delete mode 100644 arch/arm/mach-at91/board-cpuat91.c delete mode 100644 arch/arm/mach-at91/board-csb337.c delete mode 100644 arch/arm/mach-at91/board-csb637.c delete mode 100644 arch/arm/mach-at91/board-eb9200.c delete mode 100644 arch/arm/mach-at91/board-ecbat91.c delete mode 100644 arch/arm/mach-at91/board-eco920.c delete mode 100644 arch/arm/mach-at91/board-kafa.c delete mode 100644 arch/arm/mach-at91/board-kb9202.c delete mode 100644 arch/arm/mach-at91/board-picotux200.c delete mode 100644 arch/arm/mach-at91/board-rm9200ek.c delete mode 100644 arch/arm/mach-at91/board-yl-9200.c diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index b2495d71f7ac..016d9a126eb9 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -22,21 +22,6 @@ obj-$(CONFIG_SOC_SAMA5D4) += sama5d4.o obj-$(CONFIG_ARCH_AT91RM9200) += at91rm9200_devices.o -# AT91RM9200 board-specific support -obj-$(CONFIG_MACH_ONEARM) += board-1arm.o -obj-$(CONFIG_MACH_AT91RM9200EK) += board-rm9200ek.o -obj-$(CONFIG_MACH_CSB337) += board-csb337.o -obj-$(CONFIG_MACH_CSB637) += board-csb637.o -obj-$(CONFIG_MACH_CARMEVA) += board-carmeva.o -obj-$(CONFIG_MACH_KB9200) += board-kb9202.o -obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o -obj-$(CONFIG_MACH_KAFA) += board-kafa.o -obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o -obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o -obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o -obj-$(CONFIG_MACH_CPUAT91) += board-cpuat91.o -obj-$(CONFIG_MACH_ECO920) += board-eco920.o - # AT91SAM board with device-tree obj-$(CONFIG_MACH_AT91RM9200_DT) += board-dt-rm9200.o obj-$(CONFIG_MACH_AT91SAM9_DT) += board-dt-sam9.o diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c deleted file mode 100644 index 3f6dbcc34022..000000000000 --- a/arch/arm/mach-at91/board-1arm.c +++ /dev/null @@ -1,99 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-1arm.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - -static void __init onearm_init_early(void) -{ - /* Set cpu type: PQFP */ - at91rm9200_set_type(ARCH_REVISON_9200_PQFP); - - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata onearm_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata onearm_usbh_data = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata onearm_udc_data = { - .vbus_pin = AT91_PIN_PC2, - .pullup_pin = AT91_PIN_PC3, -}; - -static void __init onearm_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - - /* USART1 on ttyS2 (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&onearm_eth_data); - /* USB Host */ - at91_add_device_usbh(&onearm_usbh_data); - /* USB Device */ - at91_add_device_udc(&onearm_udc_data); -} - -MACHINE_START(ONEARM, "Ajeco 1ARM single board computer") - /* Maintainer: Lennert Buytenhek */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = onearm_init_early, - .init_irq = at91_init_irq_default, - .init_machine = onearm_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c deleted file mode 100644 index 47313d3ee037..000000000000 --- a/arch/arm/mach-at91/board-carmeva.c +++ /dev/null @@ -1,167 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-carmeva.c - * - * Copyright (c) 2005 Peer Georgi - * Conitec Datasystems - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init carmeva_init_early(void) -{ - /* Initialize processor: 20.000 MHz crystal */ - at91_initialize(20000000); -} - -static struct macb_platform_data __initdata carmeva_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata carmeva_usbh_data = { - .ports = 2, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata carmeva_udc_data = { - .vbus_pin = AT91_PIN_PD12, - .pullup_pin = AT91_PIN_PD9, -}; - -/* FIXME: user dependent */ -// static struct at91_cf_data __initdata carmeva_cf_data = { -// .det_pin = AT91_PIN_PB0, -// .rst_pin = AT91_PIN_PC5, - // .irq_pin = -EINVAL, - // .vcc_pin = -EINVAL, -// }; - -static struct mci_platform_data __initdata carmeva_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PB10, - .wp_pin = AT91_PIN_PC14, - }, -}; - -static struct spi_board_info carmeva_spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 10 * 1000 * 1000, - }, - { /* User accessible spi - cs1 (250KHz) */ - .modalias = "spi-cs1", - .chip_select = 1, - .max_speed_hz = 250 * 1000, - }, - { /* User accessible spi - cs2 (1MHz) */ - .modalias = "spi-cs2", - .chip_select = 2, - .max_speed_hz = 1 * 1000 * 1000, - }, - { /* User accessible spi - cs3 (10MHz) */ - .modalias = "spi-cs3", - .chip_select = 3, - .max_speed_hz = 10 * 1000 * 1000, - }, -}; - -static struct gpio_led carmeva_leds[] = { - { /* "user led 1", LED9 */ - .name = "led9", - .gpio = AT91_PIN_PA21, - .active_low = 1, - .default_trigger = "heartbeat", - }, - { /* "user led 2", LED10 */ - .name = "led10", - .gpio = AT91_PIN_PA25, - .active_low = 1, - }, - { /* "user led 3", LED11 */ - .name = "led11", - .gpio = AT91_PIN_PA26, - .active_low = 1, - }, - { /* "user led 4", LED12 */ - .name = "led12", - .gpio = AT91_PIN_PA18, - .active_low = 1, - } -}; - -static void __init carmeva_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&carmeva_eth_data); - /* USB Host */ - at91_add_device_usbh(&carmeva_usbh_data); - /* USB Device */ - at91_add_device_udc(&carmeva_udc_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* SPI */ - at91_add_device_spi(carmeva_spi_devices, ARRAY_SIZE(carmeva_spi_devices)); - /* Compact Flash */ -// at91_add_device_cf(&carmeva_cf_data); - /* MMC */ - at91_add_device_mci(0, &carmeva_mci0_data); - /* LEDs */ - at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds)); -} - -MACHINE_START(CARMEVA, "Carmeva") - /* Maintainer: Conitec Datasystems */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = carmeva_init_early, - .init_irq = at91_init_irq_default, - .init_machine = carmeva_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c deleted file mode 100644 index c094350c9314..000000000000 --- a/arch/arm/mach-at91/board-cpuat91.c +++ /dev/null @@ -1,189 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-cpuat91.c - * - * Copyright (C) 2009 Eric Benard - eric@eukrea.com - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static struct gpio_led cpuat91_leds[] = { - { - .name = "led1", - .default_trigger = "heartbeat", - .active_low = 1, - .gpio = AT91_PIN_PC0, - }, -}; - -static void __init cpuat91_init_early(void) -{ - /* Set cpu type: PQFP */ - at91rm9200_set_type(ARCH_REVISON_9200_PQFP); - - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata cpuat91_eth_data = { - .phy_irq_pin = -EINVAL, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata cpuat91_usbh_data = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata cpuat91_udc_data = { - .vbus_pin = AT91_PIN_PC15, - .pullup_pin = AT91_PIN_PC14, -}; - -static struct mci_platform_data __initdata cpuat91_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PC2, - .wp_pin = -EINVAL, - }, -}; - -static struct physmap_flash_data cpuat91_flash_data = { - .width = 2, -}; - -static struct resource cpuat91_flash_resource = { - .start = AT91_CHIPSELECT_0, - .end = AT91_CHIPSELECT_0 + SZ_16M - 1, - .flags = IORESOURCE_MEM, -}; - -static struct platform_device cpuat91_norflash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &cpuat91_flash_data, - }, - .resource = &cpuat91_flash_resource, - .num_resources = 1, -}; - -#ifdef CONFIG_MTD_PLATRAM -struct platdata_mtd_ram at91_sram_pdata = { - .mapname = "SRAM", - .bankwidth = 2, -}; - -static struct resource at91_sram_resource[] = { - [0] = { - .start = AT91RM9200_SRAM_BASE, - .end = AT91RM9200_SRAM_BASE + AT91RM9200_SRAM_SIZE - 1, - .flags = IORESOURCE_MEM, - }, -}; - -static struct platform_device at91_sram = { - .name = "mtd-ram", - .id = 0, - .resource = at91_sram_resource, - .num_resources = ARRAY_SIZE(at91_sram_resource), - .dev = { - .platform_data = &at91_sram_pdata, - }, -}; -#endif /* MTD_PLATRAM */ - -static struct platform_device *platform_devices[] __initdata = { - &cpuat91_norflash, -#ifdef CONFIG_MTD_PLATRAM - &at91_sram, -#endif /* CONFIG_MTD_PLATRAM */ -}; - -static void __init cpuat91_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | - ATMEL_UART_RTS); - - /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | - ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR | - ATMEL_UART_DCD | ATMEL_UART_RI); - - /* USART2 on ttyS3 (Rx, Tx) */ - at91_register_uart(AT91RM9200_ID_US2, 3, 0); - - /* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS | - ATMEL_UART_RTS); - at91_add_device_serial(); - /* LEDs. */ - at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds)); - /* Ethernet */ - at91_add_device_eth(&cpuat91_eth_data); - /* USB Host */ - at91_add_device_usbh(&cpuat91_usbh_data); - /* USB Device */ - at91_add_device_udc(&cpuat91_udc_data); - /* MMC */ - at91_add_device_mci(0, &cpuat91_mci0_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* Platform devices */ - platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices)); -} - -MACHINE_START(CPUAT91, "Eukrea") - /* Maintainer: Eric Benard - EUKREA Electromatique */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = cpuat91_init_early, - .init_irq = at91_init_irq_default, - .init_machine = cpuat91_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c deleted file mode 100644 index 0e35a45cf8d4..000000000000 --- a/arch/arm/mach-at91/board-csb337.c +++ /dev/null @@ -1,260 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-csb337.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - -static void __init csb337_init_early(void) -{ - /* Initialize processor: 3.6864 MHz crystal */ - at91_initialize(3686400); -} - -static struct macb_platform_data __initdata csb337_eth_data = { - .phy_irq_pin = AT91_PIN_PC2, - .is_rmii = 0, - /* The CSB337 bootloader stores the MAC the wrong-way around */ - .rev_eth_addr = 1, -}; - -static struct at91_usbh_data __initdata csb337_usbh_data = { - .ports = 2, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata csb337_udc_data = { - .pullup_pin = AT91_PIN_PA24, - .vbus_pin = -EINVAL, -}; - -static struct i2c_board_info __initdata csb337_i2c_devices[] = { - { - I2C_BOARD_INFO("ds1307", 0x68), - }, -}; - -static struct at91_cf_data __initdata csb337_cf_data = { - /* - * connector P4 on the CSB 337 mates to - * connector P8 on the CSB 300CF - */ - - /* CSB337 specific */ - .det_pin = AT91_PIN_PC3, - - /* CSB300CF specific */ - .irq_pin = AT91_PIN_PA19, - .vcc_pin = AT91_PIN_PD0, - .rst_pin = AT91_PIN_PD2, -}; - -static struct mci_platform_data __initdata csb337_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PD5, - .wp_pin = AT91_PIN_PD6, - }, -}; - -static struct spi_board_info csb337_spi_devices[] = { - { /* CAN controller */ - .modalias = "sak82c900", - .chip_select = 0, - .max_speed_hz = 6 * 1000 * 1000, - }, -}; - -#define CSB_FLASH_BASE AT91_CHIPSELECT_0 -#define CSB_FLASH_SIZE SZ_8M - -static struct mtd_partition csb_flash_partitions[] = { - { - .name = "uMON flash", - .offset = 0, - .size = MTDPART_SIZ_FULL, - .mask_flags = MTD_WRITEABLE, /* read only */ - } -}; - -static struct physmap_flash_data csb_flash_data = { - .width = 2, - .parts = csb_flash_partitions, - .nr_parts = ARRAY_SIZE(csb_flash_partitions), -}; - -static struct resource csb_flash_resources[] = { - { - .start = CSB_FLASH_BASE, - .end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device csb_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &csb_flash_data, - }, - .resource = csb_flash_resources, - .num_resources = ARRAY_SIZE(csb_flash_resources), -}; - -/* - * GPIO Buttons (on CSB300) - */ -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -static struct gpio_keys_button csb300_buttons[] = { - { - .gpio = AT91_PIN_PB29, - .code = BTN_0, - .desc = "sw0", - .active_low = 1, - .wakeup = 1, - }, - { - .gpio = AT91_PIN_PB28, - .code = BTN_1, - .desc = "sw1", - .active_low = 1, - .wakeup = 1, - }, - { - .gpio = AT91_PIN_PA21, - .code = BTN_2, - .desc = "sw2", - .active_low = 1, - .wakeup = 1, - } -}; - -static struct gpio_keys_platform_data csb300_button_data = { - .buttons = csb300_buttons, - .nbuttons = ARRAY_SIZE(csb300_buttons), -}; - -static struct platform_device csb300_button_device = { - .name = "gpio-keys", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &csb300_button_data, - } -}; - -static void __init csb300_add_device_buttons(void) -{ - at91_set_gpio_input(AT91_PIN_PB29, 1); /* sw0 */ - at91_set_deglitch(AT91_PIN_PB29, 1); - at91_set_gpio_input(AT91_PIN_PB28, 1); /* sw1 */ - at91_set_deglitch(AT91_PIN_PB28, 1); - at91_set_gpio_input(AT91_PIN_PA21, 1); /* sw2 */ - at91_set_deglitch(AT91_PIN_PA21, 1); - - platform_device_register(&csb300_button_device); -} -#else -static void __init csb300_add_device_buttons(void) {} -#endif - -static struct gpio_led csb_leds[] = { - { /* "led0", yellow */ - .name = "led0", - .gpio = AT91_PIN_PB2, - .active_low = 1, - .default_trigger = "heartbeat", - }, - { /* "led1", green */ - .name = "led1", - .gpio = AT91_PIN_PB1, - .active_low = 1, - .default_trigger = "mmc0", - }, - { /* "led2", yellow */ - .name = "led2", - .gpio = AT91_PIN_PB0, - .active_low = 1, - .default_trigger = "ide-disk", - } -}; - - -static void __init csb337_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0 */ - at91_register_uart(0, 0, 0); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&csb337_eth_data); - /* USB Host */ - at91_add_device_usbh(&csb337_usbh_data); - /* USB Device */ - at91_add_device_udc(&csb337_udc_data); - /* I2C */ - at91_add_device_i2c(csb337_i2c_devices, ARRAY_SIZE(csb337_i2c_devices)); - /* Compact Flash */ - at91_set_gpio_input(AT91_PIN_PB22, 1); /* IOIS16 */ - at91_add_device_cf(&csb337_cf_data); - /* SPI */ - at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices)); - /* MMC */ - at91_add_device_mci(0, &csb337_mci0_data); - /* NOR flash */ - platform_device_register(&csb_flash); - /* LEDs */ - at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds)); - /* Switches on CSB300 */ - csb300_add_device_buttons(); -} - -MACHINE_START(CSB337, "Cogent CSB337") - /* Maintainer: Bill Gatliff */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = csb337_init_early, - .init_irq = at91_init_irq_default, - .init_machine = csb337_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c deleted file mode 100644 index 18d027f529a8..000000000000 --- a/arch/arm/mach-at91/board-csb637.c +++ /dev/null @@ -1,142 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-csb637.c - * - * Copyright (C) 2005 SAN People - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init csb637_init_early(void) -{ - /* Initialize processor: 3.6864 MHz crystal */ - at91_initialize(3686400); -} - -static struct macb_platform_data __initdata csb637_eth_data = { - .phy_irq_pin = AT91_PIN_PC0, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata csb637_usbh_data = { - .ports = 2, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata csb637_udc_data = { - .vbus_pin = AT91_PIN_PB28, - .pullup_pin = AT91_PIN_PB1, -}; - -#define CSB_FLASH_BASE AT91_CHIPSELECT_0 -#define CSB_FLASH_SIZE SZ_16M - -static struct mtd_partition csb_flash_partitions[] = { - { - .name = "uMON flash", - .offset = 0, - .size = MTDPART_SIZ_FULL, - .mask_flags = MTD_WRITEABLE, /* read only */ - } -}; - -static struct physmap_flash_data csb_flash_data = { - .width = 2, - .parts = csb_flash_partitions, - .nr_parts = ARRAY_SIZE(csb_flash_partitions), -}; - -static struct resource csb_flash_resources[] = { - { - .start = CSB_FLASH_BASE, - .end = CSB_FLASH_BASE + CSB_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device csb_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &csb_flash_data, - }, - .resource = csb_flash_resources, - .num_resources = ARRAY_SIZE(csb_flash_resources), -}; - -static struct gpio_led csb_leds[] = { - { /* "d1", red */ - .name = "d1", - .gpio = AT91_PIN_PB2, - .active_low = 1, - .default_trigger = "heartbeat", - }, -}; - -static void __init csb637_board_init(void) -{ - /* LED(s) */ - at91_gpio_leds(csb_leds, ARRAY_SIZE(csb_leds)); - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&csb637_eth_data); - /* USB Host */ - at91_add_device_usbh(&csb637_usbh_data); - /* USB Device */ - at91_add_device_udc(&csb637_udc_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* SPI */ - at91_add_device_spi(NULL, 0); - /* NOR flash */ - platform_device_register(&csb_flash); -} - -MACHINE_START(CSB637, "Cogent CSB637") - /* Maintainer: Bill Gatliff */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = csb637_init_early, - .init_irq = at91_init_irq_default, - .init_machine = csb637_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c deleted file mode 100644 index aa457a8b22f5..000000000000 --- a/arch/arm/mach-at91/board-eb9200.c +++ /dev/null @@ -1,126 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-eb9200.c - * - * Copyright (C) 2005 SAN People, adapted for ATEB9200 from Embest - * by Andrew Patrikalakis - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init eb9200_init_early(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata eb9200_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata eb9200_usbh_data = { - .ports = 2, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata eb9200_udc_data = { - .vbus_pin = AT91_PIN_PD4, - .pullup_pin = AT91_PIN_PD5, -}; - -static struct at91_cf_data __initdata eb9200_cf_data = { - .irq_pin = -EINVAL, - .det_pin = AT91_PIN_PB0, - .vcc_pin = -EINVAL, - .rst_pin = AT91_PIN_PC5, -}; - -static struct mci_platform_data __initdata eb9200_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = -EINVAL, - .wp_pin = -EINVAL, - }, -}; - -static struct i2c_board_info __initdata eb9200_i2c_devices[] = { - { - I2C_BOARD_INFO("24c512", 0x50), - }, -}; - - -static void __init eb9200_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - - /* USART2 on ttyS2. (Rx, Tx) - IRDA */ - at91_register_uart(AT91RM9200_ID_US2, 2, 0); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&eb9200_eth_data); - /* USB Host */ - at91_add_device_usbh(&eb9200_usbh_data); - /* USB Device */ - at91_add_device_udc(&eb9200_udc_data); - /* I2C */ - at91_add_device_i2c(eb9200_i2c_devices, ARRAY_SIZE(eb9200_i2c_devices)); - /* Compact Flash */ - at91_add_device_cf(&eb9200_cf_data); - /* SPI */ - at91_add_device_spi(NULL, 0); - /* MMC */ - /* only supports 1 or 4 bit interface, not wired through to SPI */ - at91_add_device_mci(0, &eb9200_mci0_data); -} - -MACHINE_START(ATEB9200, "Embest ATEB9200") - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = eb9200_init_early, - .init_irq = at91_init_irq_default, - .init_machine = eb9200_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c deleted file mode 100644 index ede1373ccaba..000000000000 --- a/arch/arm/mach-at91/board-ecbat91.c +++ /dev/null @@ -1,191 +0,0 @@ -/* - * linux/arch/arm/mach-at91rm9200/board-ecbat91.c - * Copyright (C) 2007 emQbit.com. - * - * We started from board-dk.c, which is Copyright (C) 2005 SAN People. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init ecb_at91init_early(void) -{ - /* Set cpu type: PQFP */ - at91rm9200_set_type(ARCH_REVISON_9200_PQFP); - - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata ecb_at91eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata ecb_at91usbh_data = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct mci_platform_data __initdata ecbat91_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = -EINVAL, - .wp_pin = -EINVAL, - }, -}; - - -#if defined(CONFIG_MTD_DATAFLASH) -static struct mtd_partition __initdata my_flash0_partitions[] = -{ - { /* 0x8400 */ - .name = "Darrell-loader", - .offset = 0, - .size = 12 * 1056, - }, - { - .name = "U-boot", - .offset = MTDPART_OFS_NXTBLK, - .size = 110 * 1056, - }, - { /* 1336 (167 blocks) pages * 1056 bytes = 0x158700 bytes */ - .name = "UBoot-env", - .offset = MTDPART_OFS_NXTBLK, - .size = 8 * 1056, - }, - { /* 1336 (167 blocks) pages * 1056 bytes = 0x158700 bytes */ - .name = "Kernel", - .offset = MTDPART_OFS_NXTBLK, - .size = 1534 * 1056, - }, - { /* 190200 - jffs2 root filesystem */ - .name = "Filesystem", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL, /* 26 sectors */ - } -}; - -static struct flash_platform_data __initdata my_flash0_platform = { - .name = "Removable flash card", - .parts = my_flash0_partitions, - .nr_parts = ARRAY_SIZE(my_flash0_partitions) -}; - -#endif - -static struct spi_board_info __initdata ecb_at91spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 10 * 1000 * 1000, - .bus_num = 0, -#if defined(CONFIG_MTD_DATAFLASH) - .platform_data = &my_flash0_platform, -#endif - }, - { /* User accessible spi - cs1 (250KHz) */ - .modalias = "spi-cs1", - .chip_select = 1, - .max_speed_hz = 250 * 1000, - }, - { /* User accessible spi - cs2 (1MHz) */ - .modalias = "spi-cs2", - .chip_select = 2, - .max_speed_hz = 1 * 1000 * 1000, - }, - { /* User accessible spi - cs3 (10MHz) */ - .modalias = "spi-cs3", - .chip_select = 3, - .max_speed_hz = 10 * 1000 * 1000, - }, -}; - -/* - * LEDs - */ -static struct gpio_led ecb_leds[] = { - { /* D1 */ - .name = "led1", - .gpio = AT91_PIN_PC7, - .active_low = 1, - .default_trigger = "heartbeat", - } -}; - -static void __init ecb_at91board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1. (Rx & Tx only) */ - at91_register_uart(AT91RM9200_ID_US0, 1, 0); - at91_add_device_serial(); - - /* Ethernet */ - at91_add_device_eth(&ecb_at91eth_data); - - /* USB Host */ - at91_add_device_usbh(&ecb_at91usbh_data); - - /* I2C */ - at91_add_device_i2c(NULL, 0); - - /* MMC */ - at91_add_device_mci(0, &ecbat91_mci0_data); - - /* SPI */ - at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices)); - - /* LEDs */ - at91_gpio_leds(ecb_leds, ARRAY_SIZE(ecb_leds)); -} - -MACHINE_START(ECBAT91, "emQbit's ECB_AT91") - /* Maintainer: emQbit.com */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = ecb_at91init_early, - .init_irq = at91_init_irq_default, - .init_machine = ecb_at91board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c deleted file mode 100644 index 4e75321a8f2a..000000000000 --- a/arch/arm/mach-at91/board-eco920.c +++ /dev/null @@ -1,160 +0,0 @@ -/* - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA - */ - -#include -#include -#include -#include - -#include - -#include -#include - -#include -#include -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init eco920_init_early(void) -{ - /* Set cpu type: PQFP */ - at91rm9200_set_type(ARCH_REVISON_9200_PQFP); - - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata eco920_eth_data = { - .phy_irq_pin = AT91_PIN_PC2, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata eco920_usbh_data = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata eco920_udc_data = { - .vbus_pin = AT91_PIN_PB12, - .pullup_pin = AT91_PIN_PB13, -}; - -static struct mci_platform_data __initdata eco920_mci0_data = { - .slot[0] = { - .bus_width = 1, - .detect_pin = -EINVAL, - .wp_pin = -EINVAL, - }, -}; - -static struct physmap_flash_data eco920_flash_data = { - .width = 2, -}; - -static struct resource eco920_flash_resource = { - .start = 0x11000000, - .end = 0x11ffffff, - .flags = IORESOURCE_MEM, -}; - -static struct platform_device eco920_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &eco920_flash_data, - }, - .resource = &eco920_flash_resource, - .num_resources = 1, -}; - -static struct spi_board_info eco920_spi_devices[] = { - { /* CAN controller */ - .modalias = "tlv5638", - .chip_select = 3, - .max_speed_hz = 20 * 1000 * 1000, - .mode = SPI_CPHA, - }, -}; - -/* - * LEDs - */ -static struct gpio_led eco920_leds[] = { - { /* D1 */ - .name = "led1", - .gpio = AT91_PIN_PB0, - .active_low = 1, - .default_trigger = "heartbeat", - }, - { /* D2 */ - .name = "led2", - .gpio = AT91_PIN_PB1, - .active_low = 1, - .default_trigger = "timer", - } -}; - -static void __init eco920_board_init(void) -{ - /* DBGU on ttyS0. (Rx & Tx only */ - at91_register_uart(0, 0, 0); - at91_add_device_serial(); - at91_add_device_eth(&eco920_eth_data); - at91_add_device_usbh(&eco920_usbh_data); - at91_add_device_udc(&eco920_udc_data); - - at91_add_device_mci(0, &eco920_mci0_data); - platform_device_register(&eco920_flash); - - at91_ramc_write(0, AT91_SMC_CSR(7), AT91_SMC_RWHOLD_(1) - | AT91_SMC_RWSETUP_(1) - | AT91_SMC_DBW_8 - | AT91_SMC_WSEN - | AT91_SMC_NWS_(15)); - - at91_set_A_periph(AT91_PIN_PC6, 1); - - at91_set_gpio_input(AT91_PIN_PA23, 0); - at91_set_deglitch(AT91_PIN_PA23, 1); - -/* Initialization of the Static Memory Controller for Chip Select 3 */ - at91_ramc_write(0, AT91_SMC_CSR(3), - AT91_SMC_DBW_16 | /* 16 bit */ - AT91_SMC_WSEN | - AT91_SMC_NWS_(5) | /* wait states */ - AT91_SMC_TDF_(1) /* float time */ - ); - - at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices)); - /* LEDs */ - at91_gpio_leds(eco920_leds, ARRAY_SIZE(eco920_leds)); -} - -MACHINE_START(ECO920, "eco920") - /* Maintainer: Sascha Hauer */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = eco920_init_early, - .init_irq = at91_init_irq_default, - .init_machine = eco920_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c deleted file mode 100644 index 93b1df42f639..000000000000 --- a/arch/arm/mach-at91/board-kafa.c +++ /dev/null @@ -1,113 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-kafa.c - * - * Copyright (C) 2006 Sperry-Sun - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init kafa_init_early(void) -{ - /* Set cpu type: PQFP */ - at91rm9200_set_type(ARCH_REVISON_9200_PQFP); - - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata kafa_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata kafa_usbh_data = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata kafa_udc_data = { - .vbus_pin = AT91_PIN_PB6, - .pullup_pin = AT91_PIN_PB7, -}; - -/* - * LEDs - */ -static struct gpio_led kafa_leds[] = { - { /* D1 */ - .name = "led1", - .gpio = AT91_PIN_PB4, - .active_low = 1, - .default_trigger = "heartbeat", - }, -}; - -static void __init kafa_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx, Tx, CTS, RTS) */ - at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&kafa_eth_data); - /* USB Host */ - at91_add_device_usbh(&kafa_usbh_data); - /* USB Device */ - at91_add_device_udc(&kafa_udc_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* SPI */ - at91_add_device_spi(NULL, 0); - /* LEDs */ - at91_gpio_leds(kafa_leds, ARRAY_SIZE(kafa_leds)); -} - -MACHINE_START(KAFA, "Sperry-Sun KAFA") - /* Maintainer: Sergei Sharonov */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = kafa_init_early, - .init_irq = at91_init_irq_default, - .init_machine = kafa_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c deleted file mode 100644 index d58d36225e08..000000000000 --- a/arch/arm/mach-at91/board-kb9202.c +++ /dev/null @@ -1,159 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-kb9202.c - * - * Copyright (c) 2005 kb_admin - * KwikByte, Inc. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init kb9202_init_early(void) -{ - /* Set cpu type: PQFP */ - at91rm9200_set_type(ARCH_REVISON_9200_PQFP); - - /* Initialize processor: 10 MHz crystal */ - at91_initialize(10000000); -} - -static struct macb_platform_data __initdata kb9202_eth_data = { - .phy_irq_pin = AT91_PIN_PB29, - .is_rmii = 0, -}; - -static struct at91_usbh_data __initdata kb9202_usbh_data = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata kb9202_udc_data = { - .vbus_pin = AT91_PIN_PB24, - .pullup_pin = AT91_PIN_PB22, -}; - -static struct mci_platform_data __initdata kb9202_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PB2, - .wp_pin = -EINVAL, - }, -}; - -static struct mtd_partition __initdata kb9202_nand_partition[] = { - { - .name = "nand_fs", - .offset = 0, - .size = MTDPART_SIZ_FULL, - }, -}; - -static struct atmel_nand_data __initdata kb9202_nand_data = { - .ale = 22, - .cle = 21, - .det_pin = -EINVAL, - .rdy_pin = AT91_PIN_PC29, - .enable_pin = AT91_PIN_PC28, - .ecc_mode = NAND_ECC_SOFT, - .parts = kb9202_nand_partition, - .num_parts = ARRAY_SIZE(kb9202_nand_partition), -}; - -/* - * LEDs - */ -static struct gpio_led kb9202_leds[] = { - { /* D1 */ - .name = "led1", - .gpio = AT91_PIN_PC19, - .active_low = 1, - .default_trigger = "heartbeat", - }, - { /* D2 */ - .name = "led2", - .gpio = AT91_PIN_PC18, - .active_low = 1, - .default_trigger = "timer", - } -}; - -static void __init kb9202_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART0 on ttyS1 (Rx & Tx only) */ - at91_register_uart(AT91RM9200_ID_US0, 1, 0); - - /* USART1 on ttyS2 (Rx & Tx only) - IRDA (optional) */ - at91_register_uart(AT91RM9200_ID_US1, 2, 0); - - /* USART3 on ttyS3 (Rx, Tx, CTS, RTS) - RS485 (optional) */ - at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&kb9202_eth_data); - /* USB Host */ - at91_add_device_usbh(&kb9202_usbh_data); - /* USB Device */ - at91_add_device_udc(&kb9202_udc_data); - /* MMC */ - at91_add_device_mci(0, &kb9202_mci0_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* SPI */ - at91_add_device_spi(NULL, 0); - /* NAND */ - at91_add_device_nand(&kb9202_nand_data); - /* LEDs */ - at91_gpio_leds(kb9202_leds, ARRAY_SIZE(kb9202_leds)); -} - -MACHINE_START(KB9200, "KB920x") - /* Maintainer: KwikByte, Inc. */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = kb9202_init_early, - .init_irq = at91_init_irq_default, - .init_machine = kb9202_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c deleted file mode 100644 index 2c0f2d554d84..000000000000 --- a/arch/arm/mach-at91/board-picotux200.c +++ /dev/null @@ -1,129 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-picotux200.c - * - * Copyright (C) 2005 SAN People - * Copyright (C) 2007 Kleinhenz Elektronik GmbH - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include - -#include -#include -#include - -#include -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init picotux200_init_early(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata picotux200_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata picotux200_usbh_data = { - .ports = 1, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct mci_platform_data __initdata picotux200_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PB27, - .wp_pin = AT91_PIN_PA17, - }, -}; - -#define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0 -#define PICOTUX200_FLASH_SIZE SZ_4M - -static struct physmap_flash_data picotux200_flash_data = { - .width = 2, -}; - -static struct resource picotux200_flash_resource = { - .start = PICOTUX200_FLASH_BASE, - .end = PICOTUX200_FLASH_BASE + PICOTUX200_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct platform_device picotux200_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &picotux200_flash_data, - }, - .resource = &picotux200_flash_resource, - .num_resources = 1, -}; - -static void __init picotux200_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&picotux200_eth_data); - /* USB Host */ - at91_add_device_usbh(&picotux200_usbh_data); - /* I2C */ - at91_add_device_i2c(NULL, 0); - /* MMC */ - at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mci(0, &picotux200_mci0_data); - /* NOR Flash */ - platform_device_register(&picotux200_flash); -} - -MACHINE_START(PICOTUX2XX, "picotux 200") - /* Maintainer: Kleinhenz Elektronik GmbH */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = picotux200_init_early, - .init_irq = at91_init_irq_default, - .init_machine = picotux200_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c deleted file mode 100644 index 953cea416754..000000000000 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ /dev/null @@ -1,196 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-rm9200ek.c - * - * Copyright (C) 2005 SAN People - * - * Epson S1D framebuffer glue code is: - * Copyright (C) 2005 Thibaut VARENE - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init ek_init_early(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -static struct macb_platform_data __initdata ek_eth_data = { - .phy_irq_pin = AT91_PIN_PC4, - .is_rmii = 1, -}; - -static struct at91_usbh_data __initdata ek_usbh_data = { - .ports = 2, - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin = AT91_PIN_PD4, - .pullup_pin = AT91_PIN_PD5, -}; - -#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD -static struct mci_platform_data __initdata ek_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PB27, - .wp_pin = AT91_PIN_PA17, - } -}; -#endif - -static struct spi_board_info ek_spi_devices[] = { - { /* DataFlash chip */ - .modalias = "mtd_dataflash", - .chip_select = 0, - .max_speed_hz = 15 * 1000 * 1000, - }, -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - { /* DataFlash card */ - .modalias = "mtd_dataflash", - .chip_select = 3, - .max_speed_hz = 15 * 1000 * 1000, - }, -#endif -}; - -static struct i2c_board_info __initdata ek_i2c_devices[] = { - { - I2C_BOARD_INFO("ics1523", 0x26), - }, - { - I2C_BOARD_INFO("dac3550", 0x4d), - } -}; - -#define EK_FLASH_BASE AT91_CHIPSELECT_0 -#define EK_FLASH_SIZE SZ_8M - -static struct physmap_flash_data ek_flash_data = { - .width = 2, -}; - -static struct resource ek_flash_resource = { - .start = EK_FLASH_BASE, - .end = EK_FLASH_BASE + EK_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, -}; - -static struct platform_device ek_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &ek_flash_data, - }, - .resource = &ek_flash_resource, - .num_resources = 1, -}; - -static struct gpio_led ek_leds[] = { - { /* "user led 1", DS2 */ - .name = "green", - .gpio = AT91_PIN_PB0, - .active_low = 1, - .default_trigger = "mmc0", - }, - { /* "user led 2", DS4 */ - .name = "yellow", - .gpio = AT91_PIN_PB1, - .active_low = 1, - .default_trigger = "heartbeat", - }, - { /* "user led 3", DS6 */ - .name = "red", - .gpio = AT91_PIN_PB2, - .active_low = 1, - } -}; - -static void __init ek_board_init(void) -{ - /* Serial */ - /* DBGU on ttyS0. (Rx & Tx only) */ - at91_register_uart(0, 0, 0); - - /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ - at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS - | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD - | ATMEL_UART_RI); - at91_add_device_serial(); - /* Ethernet */ - at91_add_device_eth(&ek_eth_data); - /* USB Host */ - at91_add_device_usbh(&ek_usbh_data); - /* USB Device */ - at91_add_device_udc(&ek_udc_data); - at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */ - /* I2C */ - at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); - /* SPI */ - at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); -#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD - /* DataFlash card */ - at91_set_gpio_output(AT91_PIN_PB22, 0); -#else - /* MMC */ - at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */ - at91_add_device_mci(0, &ek_mci0_data); -#endif - /* NOR Flash */ - platform_device_register(&ek_flash); - /* LEDs */ - at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); - /* VGA */ -// ek_add_device_video(); -} - -MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK") - /* Maintainer: SAN People/Atmel */ - .init_time = at91rm9200_timer_init, - .map_io = at91_map_io, - .handle_irq = at91_aic_handle_irq, - .init_early = ek_init_early, - .init_irq = at91_init_irq_default, - .init_machine = ek_board_init, -MACHINE_END diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c deleted file mode 100644 index 46fdb0c68a68..000000000000 --- a/arch/arm/mach-at91/board-yl-9200.c +++ /dev/null @@ -1,597 +0,0 @@ -/* - * linux/arch/arm/mach-at91/board-yl-9200.c - * - * Adapted from various board files in arch/arm/mach-at91 - * - * Modifications for YL-9200 platform: - * Copyright (C) 2007 S. Birtles - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include - -#include -#include -#include - -#include -#include -#include -#include - -#include "at91_aic.h" -#include "board.h" -#include "generic.h" -#include "gpio.h" - - -static void __init yl9200_init_early(void) -{ - /* Set cpu type: PQFP */ - at91rm9200_set_type(ARCH_REVISON_9200_PQFP); - - /* Initialize processor: 18.432 MHz crystal */ - at91_initialize(18432000); -} - -/* - * LEDs - */ -static struct gpio_led yl9200_leds[] = { - { /* D2 */ - .name = "led2", - .gpio = AT91_PIN_PB17, - .active_low = 1, - .default_trigger = "timer", - }, - { /* D3 */ - .name = "led3", - .gpio = AT91_PIN_PB16, - .active_low = 1, - .default_trigger = "heartbeat", - }, - { /* D4 */ - .name = "led4", - .gpio = AT91_PIN_PB15, - .active_low = 1, - }, - { /* D5 */ - .name = "led5", - .gpio = AT91_PIN_PB8, - .active_low = 1, - } -}; - -/* - * Ethernet - */ -static struct macb_platform_data __initdata yl9200_eth_data = { - .phy_irq_pin = AT91_PIN_PB28, - .is_rmii = 1, -}; - -/* - * USB Host - */ -static struct at91_usbh_data __initdata yl9200_usbh_data = { - .ports = 1, /* PQFP version of AT91RM9200 */ - .vbus_pin = {-EINVAL, -EINVAL}, - .overcurrent_pin= {-EINVAL, -EINVAL}, -}; - -/* - * USB Device - */ -static struct at91_udc_data __initdata yl9200_udc_data = { - .pullup_pin = AT91_PIN_PC4, - .vbus_pin = AT91_PIN_PC5, - .pullup_active_low = 1, /* Active Low due to PNP transistor (pg 7) */ - -}; - -/* - * MMC - */ -static struct mci_platform_data __initdata yl9200_mci0_data = { - .slot[0] = { - .bus_width = 4, - .detect_pin = AT91_PIN_PB9, - .wp_pin = -EINVAL, - }, -}; - -/* - * NAND Flash - */ -static struct mtd_partition __initdata yl9200_nand_partition[] = { - { - .name = "AT91 NAND partition 1, boot", - .offset = 0, - .size = SZ_256K - }, - { - .name = "AT91 NAND partition 2, kernel", - .offset = MTDPART_OFS_NXTBLK, - .size = (2 * SZ_1M) - SZ_256K - }, - { - .name = "AT91 NAND partition 3, filesystem", - .offset = MTDPART_OFS_NXTBLK, - .size = 14 * SZ_1M - }, - { - .name = "AT91 NAND partition 4, storage", - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_16M - }, - { - .name = "AT91 NAND partition 5, ext-fs", - .offset = MTDPART_OFS_NXTBLK, - .size = SZ_32M - } -}; - -static struct atmel_nand_data __initdata yl9200_nand_data = { - .ale = 6, - .cle = 7, - .det_pin = -EINVAL, - .rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */ - .enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */ - .ecc_mode = NAND_ECC_SOFT, - .parts = yl9200_nand_partition, - .num_parts = ARRAY_SIZE(yl9200_nand_partition), -}; - -/* - * NOR Flash - */ -#define YL9200_FLASH_BASE AT91_CHIPSELECT_0 -#define YL9200_FLASH_SIZE SZ_16M - -static struct mtd_partition yl9200_flash_partitions[] = { - { - .name = "Bootloader", - .offset = 0, - .size = SZ_256K, - .mask_flags = MTD_WRITEABLE, /* force read-only */ - }, - { - .name = "Kernel", - .offset = MTDPART_OFS_NXTBLK, - .size = (2 * SZ_1M) - SZ_256K - }, - { - .name = "Filesystem", - .offset = MTDPART_OFS_NXTBLK, - .size = MTDPART_SIZ_FULL - } -}; - -static struct physmap_flash_data yl9200_flash_data = { - .width = 2, - .parts = yl9200_flash_partitions, - .nr_parts = ARRAY_SIZE(yl9200_flash_partitions), -}; - -static struct resource yl9200_flash_resources[] = { - { - .start = YL9200_FLASH_BASE, - .end = YL9200_FLASH_BASE + YL9200_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, - } -}; - -static struct platform_device yl9200_flash = { - .name = "physmap-flash", - .id = 0, - .dev = { - .platform_data = &yl9200_flash_data, - }, - .resource = yl9200_flash_resources, - .num_resources = ARRAY_SIZE(yl9200_flash_resources), -}; - -/* - * I2C (TWI) - */ -static struct i2c_board_info __initdata yl9200_i2c_devices[] = { - { /* EEPROM */ - I2C_BOARD_INFO("24c128", 0x50), - } -}; - -/* - * GPIO Buttons -*/ -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -static struct gpio_keys_button yl9200_buttons[] = { - { - .gpio = AT91_PIN_PA24, - .code = BTN_2, - .desc = "SW2", - .active_low = 1, - .wakeup = 1, - }, - { - .gpio = AT91_PIN_PB1, - .code = BTN_3, - .desc = "SW3", - .active_low = 1, - .wakeup = 1, - }, - { - .gpio = AT91_PIN_PB2, - .code = BTN_4, - .desc = "SW4", - .active_low = 1, - .wakeup = 1, - }, - { - .gpio = AT91_PIN_PB6, - .code = BTN_5, - .desc = "SW5", - .active_low = 1, - .wakeup = 1, - } -}; - -static struct gpio_keys_platform_data yl9200_button_data = { - .buttons = yl9200_buttons, - .nbuttons = ARRAY_SIZE(yl9200_buttons), -}; - -static struct platform_device yl9200_button_device = { - .name = "gpio-keys", - .id = -1, - .num_resources = 0, - .dev = { - .platform_data = &yl9200_button_data, - } -}; - -static void __init yl9200_add_device_buttons(void) -{ - at91_set_gpio_input(AT91_PIN_PA24, 1); /* SW2 */ - at91_set_deglitch(AT91_PIN_PA24, 1); - at91_set_gpio_input(AT91_PIN_PB1, 1); /* SW3 */ - at91_set_deglitch(AT91_PIN_PB1, 1); - at91_set_gpio_input(AT91_PIN_PB2, 1); /* SW4 */ - at91_set_deglitch(AT91_PIN_PB2, 1); - at91_set_gpio_input(AT91_PIN_PB6, 1); /* SW5 */ - at91_set_deglitch(AT91_PIN_PB6, 1); - - /* Enable buttons (Sheet 5) */ - at91_set_gpio_output(AT91_PIN_PB7, 1); - - platform_device_register(&yl9200_button_device); -} -#else -static void __init yl9200_add_device_buttons(void) {} -#endif - -/* - * Touchscreen - */ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -static int ads7843_pendown_state(void) -{ - return !at91_get_gpio_value(AT91_PIN_PB11); /* Touchscreen PENIRQ */ -} - -static struct ads7846_platform_data ads_info = { - .model = 7843, - .x_min = 150, - .x_max = 3830, - .y_min = 190, - .y_max = 3830, - .vref_delay_usecs = 100, - - /* For a 8" touch-screen */ - // .x_plate_ohms = 603, - // .y_plate_ohms = 332, - - /* For a 10.4" touch-screen */ - // .x_plate_ohms = 611, - // .y_plate_ohms = 325, - - .x_plate_ohms = 576, - .y_plate_ohms = 366, - - .pressure_max = 15000, /* generally nonsense on the 7843 */ - .debounce_max = 1, - .debounce_rep = 0, - .debounce_tol = (~0), - .get_pendown_state = ads7843_pendown_state, -}; - -static void __init yl9200_add_device_ts(void) -{ - at91_set_gpio_input(AT91_PIN_PB11, 1); /* Touchscreen interrupt pin */ - at91_set_gpio_input(AT91_PIN_PB10, 1); /* Touchscreen BUSY signal - not used! */ -} -#else -static void __init yl9200_add_device_ts(void) {} -#endif - -/* - * SPI devices - */ -static struct spi_board_info yl9200_spi_devices[] = { -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - { /* Touchscreen */ - .modalias = "ads7846", - .chip_select = 0, - .max_speed_hz = 5000 * 26, - .platform_data = &ads_info, - .irq = AT91_PIN_PB11, - }, -#endif - { /* CAN */ - .modalias = "mcp2510", - .chip_select = 1, - .max_speed_hz = 25000 * 26, - .irq = AT91_PIN_PC0, - } -}; - -/* - * LCD / VGA - * - * EPSON S1D13806 FB (discontinued chip) - * EPSON S1D13506 FB - */ -#if defined(CONFIG_FB_S1D13XXX) || defined(CONFIG_FB_S1D13XXX_MODULE) -#include