From 5ea417ae7749076ddaacb5b36487cae6ac920413 Mon Sep 17 00:00:00 2001 From: Shahar Levi Date: Sun, 6 Mar 2011 16:32:11 +0200 Subject: [PATCH] wl12xx: 1281/1283 support - New boot sequence Boot sequence support FREF clock and TCXO clock. WL128x has two clocks input - TCXO and FREF. TCXO is the main clock of the device, while FREF is used to sync between the GPS and the cellular modem. Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that case the FREF will be used as the WLAN/BT main clock. [Use clock enumeration as defined in linux/wl12xx.h; remove unnecessary else block in wl128x_switch_fref; remove unnecessary change in main.c; remove some unnecessary debug prints and comments; fix potential use of uninitialized value (pll_config) -- Luca] Signed-off-by: Shahar Levi Reviewed-by: Luciano Coelho Signed-off-by: Luciano Coelho --- drivers/net/wireless/wl12xx/boot.c | 183 ++++++++++++++++++++++-- drivers/net/wireless/wl12xx/sdio.c | 1 + drivers/net/wireless/wl12xx/sdio_test.c | 1 + drivers/net/wireless/wl12xx/spi.c | 1 + drivers/net/wireless/wl12xx/wl12xx.h | 1 + 5 files changed, 179 insertions(+), 8 deletions(-) diff --git a/drivers/net/wireless/wl12xx/boot.c b/drivers/net/wireless/wl12xx/boot.c index 38f3e8ba2628..9d742c1e75a9 100644 --- a/drivers/net/wireless/wl12xx/boot.c +++ b/drivers/net/wireless/wl12xx/boot.c @@ -22,6 +22,7 @@ */ #include +#include #include "acx.h" #include "reg.h" @@ -520,24 +521,159 @@ static void wl1271_boot_hw_version(struct wl1271 *wl) wl->quirks |= WL12XX_QUIRK_END_OF_TRANSACTION; } -/* uploads NVS and firmware */ -int wl1271_load_firmware(struct wl1271 *wl) +/* + * WL128x has two clocks input - TCXO and FREF. + * TCXO is the main clock of the device, while FREF is used to sync + * between the GPS and the cellular modem. + * In cases where TCXO is 32.736MHz or 16.368MHz, the FREF will be used + * as the WLAN/BT main clock. + */ +static int wl128x_switch_fref(struct wl1271 *wl, bool *is_ref_clk) { - int ret = 0; - u32 tmp, clk, pause; + u16 sys_clk_cfg_val; + + /* if working on XTAL-only mode go directly to TCXO TO FREF SWITCH */ + if ((wl->ref_clock == CONF_REF_CLK_38_4_M_XTAL) || + (wl->ref_clock == CONF_REF_CLK_26_M_XTAL)) + return true; + + /* Read clock source FREF or TCXO */ + sys_clk_cfg_val = wl1271_top_reg_read(wl, SYS_CLK_CFG_REG); + + if (sys_clk_cfg_val & PRCM_CM_EN_MUX_WLAN_FREF) { + /* if bit 3 is set - working with FREF clock */ + wl1271_debug(DEBUG_BOOT, "working with FREF clock, skip" + " to FREF"); + + *is_ref_clk = true; + } else { + /* if bit 3 is clear - working with TCXO clock */ + wl1271_debug(DEBUG_BOOT, "working with TCXO clock"); + + /* TCXO to FREF switch, check TXCO clock config */ + if ((wl->tcxo_clock != WL12XX_TCXOCLOCK_16_368) && + (wl->tcxo_clock != WL12XX_TCXOCLOCK_32_736)) { + /* + * not 16.368Mhz and not 32.736Mhz - skip to + * configure ELP stage + */ + wl1271_debug(DEBUG_BOOT, "NEW PLL ALGO:" + " TcxoRefClk=%d - not 16.368Mhz and not" + " 32.736Mhz - skip to configure ELP" + " stage", wl->tcxo_clock); + + *is_ref_clk = false; + } else { + wl1271_debug(DEBUG_BOOT, "NEW PLL ALGO:" + "TcxoRefClk=%d - 16.368Mhz or 32.736Mhz" + " - TCXO to FREF switch", + wl->tcxo_clock); + + return true; + } + } + + return false; +} + +static int wl128x_boot_clk(struct wl1271 *wl, bool *is_ref_clk) +{ + if (wl128x_switch_fref(wl, is_ref_clk)) { + wl1271_debug(DEBUG_BOOT, "XTAL-only mode go directly to" + " TCXO TO FREF SWITCH"); + /* TCXO to FREF switch - for PG2.0 */ + wl1271_top_reg_write(wl, WL_SPARE_REG, + WL_SPARE_MASK_8526); + + wl1271_top_reg_write(wl, SYS_CLK_CFG_REG, + WL_CLK_REQ_TYPE_PG2 | MCS_PLL_CLK_SEL_FREF); + + *is_ref_clk = true; + mdelay(15); + } + + /* Set bit 2 in spare register to avoid illegal access */ + wl1271_top_reg_write(wl, WL_SPARE_REG, WL_SPARE_VAL); + + /* working with TCXO clock */ + if ((*is_ref_clk == false) && + ((wl->tcxo_clock == WL12XX_TCXOCLOCK_16_8) || + (wl->tcxo_clock == WL12XX_TCXOCLOCK_33_6))) { + wl1271_debug(DEBUG_BOOT, "16_8_M or 33_6_M TCXO detected"); + + /* Manually Configure MCS PLL settings PG2.0 Only */ + wl1271_top_reg_write(wl, MCS_PLL_M_REG, MCS_PLL_M_REG_VAL); + wl1271_top_reg_write(wl, MCS_PLL_N_REG, MCS_PLL_N_REG_VAL); + wl1271_top_reg_write(wl, MCS_PLL_CONFIG_REG, + MCS_PLL_CONFIG_REG_VAL); + } else { + int pll_config; + u16 mcs_pll_config_val; + + /* + * Configure MCS PLL settings to FREF Freq + * Set the values that determine the time elapse since the PLL's + * get their enable signal until the lock indication is set + */ + wl1271_top_reg_write(wl, PLL_LOCK_COUNTERS_REG, + PLL_LOCK_COUNTERS_COEX | PLL_LOCK_COUNTERS_MCS); + + mcs_pll_config_val = wl1271_top_reg_read(wl, + MCS_PLL_CONFIG_REG); + /* + * Set the MCS PLL input frequency value according to the + * reference clock value detected/read + */ + if (*is_ref_clk == false) { + if ((wl->tcxo_clock == WL12XX_TCXOCLOCK_19_2) || + (wl->tcxo_clock == WL12XX_TCXOCLOCK_38_4)) + pll_config = 1; + else if ((wl->tcxo_clock == WL12XX_TCXOCLOCK_26) + || + (wl->tcxo_clock == WL12XX_TCXOCLOCK_52)) + pll_config = 2; + else + return -EINVAL; + } else { + if ((wl->ref_clock == CONF_REF_CLK_19_2_E) || + (wl->ref_clock == CONF_REF_CLK_38_4_E)) + pll_config = 1; + else if ((wl->ref_clock == CONF_REF_CLK_26_E) || + (wl->ref_clock == CONF_REF_CLK_52_E)) + pll_config = 2; + else + return -EINVAL; + } + + mcs_pll_config_val |= (pll_config << (MCS_SEL_IN_FREQ_SHIFT)) & + (MCS_SEL_IN_FREQ_MASK); + wl1271_top_reg_write(wl, MCS_PLL_CONFIG_REG, + mcs_pll_config_val); + } + + return 0; +} + +static int wl127x_boot_clk(struct wl1271 *wl) +{ + u32 pause; + u32 clk; wl1271_boot_hw_version(wl); - if (wl->ref_clock == 0 || wl->ref_clock == 2 || wl->ref_clock == 4) + if (wl->ref_clock == CONF_REF_CLK_19_2_E || + wl->ref_clock == CONF_REF_CLK_38_4_E || + wl->ref_clock == CONF_REF_CLK_38_4_M_XTAL) /* ref clk: 19.2/38.4/38.4-XTAL */ clk = 0x3; - else if (wl->ref_clock == 1 || wl->ref_clock == 3) + else if (wl->ref_clock == CONF_REF_CLK_26_E || + wl->ref_clock == CONF_REF_CLK_52_E) /* ref clk: 26/52 */ clk = 0x5; else return -EINVAL; - if (wl->ref_clock != 0) { + if (wl->ref_clock != CONF_REF_CLK_19_2_E) { u16 val; /* Set clock type (open drain) */ val = wl1271_top_reg_read(wl, OCP_REG_CLK_TYPE); @@ -567,6 +703,26 @@ int wl1271_load_firmware(struct wl1271 *wl) pause |= WU_COUNTER_PAUSE_VAL; wl1271_write32(wl, WU_COUNTER_PAUSE, pause); + return 0; +} + +/* uploads NVS and firmware */ +int wl1271_load_firmware(struct wl1271 *wl) +{ + int ret = 0; + u32 tmp, clk; + bool is_ref_clk = false; + + if (wl->chip.id == CHIP_ID_1283_PG20) { + ret = wl128x_boot_clk(wl, &is_ref_clk); + if (ret < 0) + goto out; + } else { + ret = wl127x_boot_clk(wl); + if (ret < 0) + goto out; + } + /* Continue the ELP wake up sequence */ wl1271_write32(wl, WELP_ARM_COMMAND, WELP_ARM_COMMAND_VAL); udelay(500); @@ -582,7 +738,15 @@ int wl1271_load_firmware(struct wl1271 *wl) wl1271_debug(DEBUG_BOOT, "clk2 0x%x", clk); - clk |= (wl->ref_clock << 1) << 4; + if (wl->chip.id == CHIP_ID_1283_PG20) { + if (is_ref_clk == false) + clk |= ((wl->tcxo_clock & 0x3) << 1) << 4; + else + clk |= ((wl->ref_clock & 0x3) << 1) << 4; + } else { + clk |= (wl->ref_clock << 1) << 4; + } + wl1271_write32(wl, DRPW_SCRATCH_START, clk); wl1271_set_partition(wl, &part_table[PART_WORK]); @@ -615,6 +779,9 @@ int wl1271_load_firmware(struct wl1271 *wl) /* WL1271: The reference driver skips steps 7 to 10 (jumps directly * to upload_fw) */ + if (wl->chip.id == CHIP_ID_1283_PG20) + wl1271_top_reg_write(wl, SDIO_IO_DS, HCI_IO_DS_6MA); + ret = wl1271_boot_upload_firmware(wl); if (ret < 0) goto out; diff --git a/drivers/net/wireless/wl12xx/sdio.c b/drivers/net/wireless/wl12xx/sdio.c index 7491b3d8487a..f6dd3dea4f30 100644 --- a/drivers/net/wireless/wl12xx/sdio.c +++ b/drivers/net/wireless/wl12xx/sdio.c @@ -255,6 +255,7 @@ static int __devinit wl1271_probe(struct sdio_func *func, wl->irq = wlan_data->irq; wl->ref_clock = wlan_data->board_ref_clock; + wl->tcxo_clock = wlan_data->board_tcxo_clock; ret = request_threaded_irq(wl->irq, wl1271_hardirq, wl1271_irq, IRQF_TRIGGER_HIGH | IRQF_ONESHOT, diff --git a/drivers/net/wireless/wl12xx/sdio_test.c b/drivers/net/wireless/wl12xx/sdio_test.c index e6e2ad63a1c1..c02c87046615 100644 --- a/drivers/net/wireless/wl12xx/sdio_test.c +++ b/drivers/net/wireless/wl12xx/sdio_test.c @@ -421,6 +421,7 @@ static int __devinit wl1271_probe(struct sdio_func *func, wl->irq = wlan_data->irq; wl->ref_clock = wlan_data->board_ref_clock; + wl->tcxo_clock = wlan_data->board_tcxo_clock; sdio_set_drvdata(func, wl_test); diff --git a/drivers/net/wireless/wl12xx/spi.c b/drivers/net/wireless/wl12xx/spi.c index bfb1171176ca..f5525361f2f5 100644 --- a/drivers/net/wireless/wl12xx/spi.c +++ b/drivers/net/wireless/wl12xx/spi.c @@ -401,6 +401,7 @@ static int __devinit wl1271_probe(struct spi_device *spi) } wl->ref_clock = pdata->board_ref_clock; + wl->tcxo_clock = pdata->board_tcxo_clock; wl->irq = spi->irq; if (wl->irq < 0) { diff --git a/drivers/net/wireless/wl12xx/wl12xx.h b/drivers/net/wireless/wl12xx/wl12xx.h index e59f5392e909..4b556776fd57 100644 --- a/drivers/net/wireless/wl12xx/wl12xx.h +++ b/drivers/net/wireless/wl12xx/wl12xx.h @@ -535,6 +535,7 @@ struct wl1271 { u8 ba_rx_bitmap; u32 block_size; + int tcxo_clock; /* * AP-mode - links indexed by HLID. The global and broadcast links -- 2.34.1