From 7911fc439b5e77f054e5280e5a2f015931bb0293 Mon Sep 17 00:00:00 2001 From: Pau Pajuel Date: Sat, 16 Jan 2016 11:51:11 +0100 Subject: [PATCH] ARM: dts: omap3-igep0030-common: Add USB Host support Provide RESET GPIO for the USB PHY, the USB Host port mode and the PHY device for the controller. Also provides pin multiplexer information for USB host pins. Signed-off-by: Pau Pajuel Signed-off-by: Enric Balletbo i Serra Reviewed-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep0030-common.dtsi | 41 ++++++++++++++++++++ 1 file changed, 41 insertions(+) diff --git a/arch/arm/boot/dts/omap3-igep0030-common.dtsi b/arch/arm/boot/dts/omap3-igep0030-common.dtsi index 640f06603966..63f8b9a2f3af 100644 --- a/arch/arm/boot/dts/omap3-igep0030-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0030-common.dtsi @@ -33,9 +33,28 @@ default-state = "off"; }; }; + + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* gpio_54 */ + }; }; &omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb2_pins>; + + hsusb2_pins: pinmux_hsusb2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + >; + }; + uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */ @@ -47,6 +66,20 @@ }; &omap3_pmx_core2 { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb2_core2_pins>; + + hsusb2_core2_pins: pinmux_hsusb2_core2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; + leds_core2_pins: pinmux_leds_core2_pins { pinctrl-single,pins = < OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */ @@ -54,6 +87,14 @@ }; }; +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + &uart2 { pinctrl-names = "default"; pinctrl-0 = <&uart2_pins>; -- 2.34.1